Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.8 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 803485/tftp-deploy-hrd60gip/kernel/zImage tftp 0x82000000 803485/tftp-deploy-hrd60gip/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.8 Filename '803485/tftp-deploy-hrd60gip/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 5.1 MiB/s done Bytes transferred = 4595352 (461e98 hex) => tftp 0x83000000 803485/tftp-deploy-hrd60gip/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 803485/tftp-deploy-hrd60gip/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.8 Filename '803485/tftp-deploy-hrd60gip/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 5.1 MiB/s done Bytes transferred = 14146054 (d7da06 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 803485/tftp-deploy-hrd60gip/dtb/am335x-boneblack.dtb tftp 0x88000000 803485/tftp-deploy-hrd60gip/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.8 Filename '803485/tftp-deploy-hrd60gip/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2022-12-11 19:28:31 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14145990 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.158-cip22-rt9 (KernelCI@build-j680951-arm-gcc-10-omap2plus-defconfig-9p26n) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun Dec 11 17:45:55 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] On node 0 totalpages: 130560 [ 0.000000] Normal zone: 1148 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 130560 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 16 pages/cpu s33484 r8192 d23860 u65536 [ 0.000000] pcpu-alloc: s33484 r8192 d23860 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472060K/522240K available (9216K kernel code, 1041K rwdata, 2168K rodata, 1024K init, 271K bss, 33796K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008338] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018544] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030205] Console: colour dummy device 80x30 <3>[ 0.035077] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042134] This ensures that you still see kernel messages. Please <3>[ 0.048860] update your kernel commandline. <6>[ 0.053462] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095545] pid_max: default: 32768 minimum: 301 <6>[ 0.100716] LSM: Security Framework initializing <6>[ 0.105825] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.113646] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.122932] CPU: Testing write buffer coherency: ok <6>[ 0.128293] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.134198] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140688] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147889] rcu: Hierarchical SRCU implementation. <6>[ 0.153727] smp: Bringing up secondary CPUs ... <6>[ 0.158666] smp: Brought up 1 node, 1 CPU <6>[ 0.163112] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169855] CPU: All CPU(s) started in SVC mode. <6>[ 0.175598] devtmpfs: initialized <6>[ 0.191422] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199953] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210394] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.219000] pinctrl core: initialized pinctrl subsystem <6>[ 0.226517] NET: Registered protocol family 16 <6>[ 0.234147] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260596] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266678] audit: initializing netlink subsys (disabled) <6>[ 0.273733] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273746] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.273751] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.274014] cpuidle: using governor menu <5>[ 1.160980] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.285438] No ATAGs? <6>[ 1.288066] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.312491] Kprobes globally optimized <7>[ 1.322870] reg-fixed-voltage fixedregulator0: GPIO lookup for consumer (null) <7>[ 1.330742] reg-fixed-voltage fixedregulator0: using device tree for GPIO lookup <7>[ 1.338639] of_get_named_gpiod_flags: can't parse 'gpios' property of node '/fixedregulator0[0]' <7>[ 1.347996] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixedregulator0[0]' <7>[ 1.357241] reg-fixed-voltage fixedregulator0: using lookup tables for GPIO lookup <7>[ 1.365314] reg-fixed-voltage fixedregulator0: No GPIO consumer (null) found <6>[ 1.375517] iommu: Default domain type: Translated <6>[ 1.382760] vgaarb: loaded <5>[ 1.386327] SCSI subsystem initialized <7>[ 1.391098] libata version 3.00 loaded. <6>[ 1.395858] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.401339] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.411062] PTP clock support registered <6>[ 1.416586] clocksource: Switched to clocksource dmtimer <5>[ 2.018619] VFS: Disk quotas dquot_6.6.0 <6>[ 2.023034] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.039972] NET: Registered protocol family 2 <6>[ 2.045053] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.053784] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.062749] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.071048] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.078732] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.085647] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.092683] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.100295] NET: Registered protocol family 1 <6>[ 2.106054] RPC: Registered named UNIX socket transport module. <6>[ 2.112520] RPC: Registered udp transport module. <6>[ 2.117651] RPC: Registered tcp transport module. <6>[ 2.122756] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.129679] PCI: CLS 0 bytes, default 64 <6>[ 2.134699] Trying to unpack rootfs image as initramfs... <6>[ 3.122441] Freeing initrd memory: 13816K <6>[ 3.128180] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.138558] Initialise system trusted keyrings <6>[ 3.143855] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.152073] NFS: Registering the id_resolver key type <5>[ 3.157695] Key type id_resolver registered <5>[ 3.162268] Key type id_legacy registered <6>[ 3.166729] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.174681] Key type asymmetric registered <5>[ 3.179246] Asymmetric key parser 'x509' registered <6>[ 3.184545] io scheduler mq-deadline registered <6>[ 3.189496] io scheduler kyber registered <3>[ 3.326996] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.335628] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.443948] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.485865] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.557474] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.566107] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.625735] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.634449] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.651907] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.660600] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.723879] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.732450] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.759586] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <7>[ 3.768471] gpio-clk clk_mcasp0: GPIO lookup for consumer enable <7>[ 3.774944] gpio-clk clk_mcasp0: using device tree for GPIO lookup <7>[ 3.781679] gpio-clk clk_mcasp0: No GPIO consumer enable found <6>[ 3.793572] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <7>[ 3.804335] omap8250 44e09000.serial: GPIO lookup for consumer rs485-term <7>[ 3.811759] omap8250 44e09000.serial: using device tree for GPIO lookup <7>[ 3.818879] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.833963] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/ocp/interconnect@44c00000/segment@200000/target-module@9000/serial@0[0]' <7>[ 3.848946] omap8250 44e09000.serial: using lookup tables for GPIO lookup <7>[ 3.856200] omap8250 44e09000.serial: No GPIO consumer rs485-term found <6>[ 3.863333] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.872755] printk: console [ttyS0] enabled <6>[ 3.872755] printk: console [ttyS0] enabled <6>[ 3.881819] printk: bootconsole [omap8250] disabled <6>[ 3.881819] printk: bootconsole [omap8250] disabled <6>[ 3.905666] brd: module loaded <6>[ 3.918113] loop: module loaded <3>[ 3.923506] mtdoops: mtd device (mtddev=name/number) must be supplied <7>[ 3.932600] mdio_bus fixed-0: GPIO lookup for consumer reset <7>[ 3.938648] mdio_bus fixed-0: using lookup tables for GPIO lookup <7>[ 3.945038] mdio_bus fixed-0: No GPIO consumer reset found <7>[ 3.955227] mdio_bus 4a101000.mdio: GPIO lookup for consumer reset <7>[ 3.961827] mdio_bus 4a101000.mdio: using device tree for GPIO lookup <7>[ 3.968597] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 3.983671] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000[0]' <7>[ 3.998651] mdio_bus 4a101000.mdio: using lookup tables for GPIO lookup <7>[ 4.005559] mdio_bus 4a101000.mdio: No GPIO consumer reset found <6>[ 4.066595] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <7>[ 4.107563] mdio_bus 4a101000.mdio:00: GPIO lookup for consumer reset <7>[ 4.114341] mdio_bus 4a101000.mdio:00: using device tree for GPIO lookup <7>[ 4.121441] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.137880] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/ocp/interconnect@4a000000/segment@0/target-module@100000/ethernet@0/mdio@1000/ethernet-phy@0[0]' <7>[ 4.154180] mdio_bus 4a101000.mdio:00: using lookup tables for GPIO lookup <7>[ 4.161371] mdio_bus 4a101000.mdio:00: No GPIO consumer reset found <6>[ 4.169256] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.179170] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.185827] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.191631] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.199214] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.208270] i2c /dev entries driver <5>[ 4.213752] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.221654] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.228195] sdhci: Copyright(c) Pierre Ossman <6>[ 4.233520] sdhci-pltfm: SDHCI platform and OF driver helper <7>[ 4.240542] sdhci-omap 48060000.mmc: GPIO lookup for consumer cd <7>[ 4.246960] sdhci-omap 48060000.mmc: using device tree for GPIO lookup <7>[ 4.253807] sdhci-omap 48060000.mmc: No GPIO consumer cd found <7>[ 4.260856] sdhci-omap 481d8000.mmc: GPIO lookup for consumer wp <7>[ 4.267264] sdhci-omap 481d8000.mmc: using device tree for GPIO lookup <7>[ 4.274098] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.287993] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/ocp/interconnect@48000000/segment@100000/target-module@d8000/mmc@0[0]' <7>[ 4.301764] sdhci-omap 481d8000.mmc: using lookup tables for GPIO lookup <7>[ 4.308780] sdhci-omap 481d8000.mmc: No GPIO consumer wp found <4>[ 4.315079] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.323667] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.331994] Initializing XFRM netlink socket <6>[ 4.336830] NET: Registered protocol family 10 <6>[ 4.343045] Segment Routing with IPv6 <6>[ 4.347171] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.354142] NET: Registered protocol family 17 <6>[ 4.358974] NET: Registered protocol family 15 <5>[ 4.363814] Key type dns_resolver registered <6>[ 4.369020] oprofile: using arm/armv7 <6>[ 4.373059] ThumbEE CPU extension supported. <5>[ 4.377694] Registering SWP/SWPB emulation handler <3>[ 4.383164] omap_voltage_late_init: Voltage driver support not added <3>[ 4.389882] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.398317] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.406990] SmartReflex Class3 initialized <6>[ 4.438946] printk: console [ttyS0]: printing thread started <5>[ 4.439023] Loading compiled-in X.509 certificates <6>[ 4.458092] OMAP GPIO hardware version 0.1 <6>[ 4.474581] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <4>[ 4.507325] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.514727] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.529390] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.530142] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.534080] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.539281] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.539291] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.539546] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.637103] mmc1: new high speed MMC card at address 0001 <6>[ 4.638203] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.638634] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.639032] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.639374] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.641449] mmcblk1: p1 <6>[ 4.693037] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.719945] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.818100] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.977241] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.996582] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.026717] Sending DHCP requests ., OK <6>[ 8.066555] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.8 <6>[ 8.066576] IP-Config: Complete: <6>[ 8.066579] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.8, mask=255.255.255.0, gw=192.168.11.1 <6>[ 8.066593] host=192.168.11.8, domain=usen.ad.jp, nis-domain=(none) <6>[ 8.066599] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.066606] nameserver0=192.168.11.1 <6>[ 8.069233] Freeing unused kernel memory: 1024K <6>[ 8.127065] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.361528] udevd[101]: starting version 3.2.9 <5>[ 8.362982] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.363377] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.363512] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.399730] udevd[101]: specified user 'tss' unknown <27>[ 8.399940] udevd[101]: specified group 'tss' unknown <30>[ 8.409364] udevd[102]: starting eudev-3.2.9 <4>[ 9.232706] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.233015] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.274141] remoteproc remoteproc0: wkup_m3 is available <6>[ 9.371264] usbcore: registered new interface driver usbfs <6>[ 9.371340] usbcore: registered new interface driver hub <6>[ 9.371425] usbcore: registered new device driver usb <4>[ 9.468078] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.468391] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.671164] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.671218] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.769315] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.769347] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.769356] usb usb1: Product: MUSB HDRC host driver <6>[ 9.769363] usb usb1: Manufacturer: Linux 5.10.158-cip22-rt9 musb-hcd <6>[ 9.769370] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.773630] hub 1-0:1.0: USB hub found <6>[ 9.773749] hub 1-0:1.0: 1 port detected <4>[ 10.038949] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 10.077039] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 10.077534] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 10.111061] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 10.140513] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 10.179269] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 10.313090] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.315792] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.315892] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 10.348683] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 10.407380] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <3>[ 10.620433] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.700040] tda998x 0-0070: found TDA19988 <3>[ 10.987430] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 11.087258] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 11.201570] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 11.244604] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 11.413705] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.413850] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.413869] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.413877] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 11.883990] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.884516] random: crng init done <6>[ 11.917218] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.919116] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 11.919537] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 11.921620] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 12.412521] PM: Cannot get wkup_m3_ipc handle <6>[ 12.459640] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.486691] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 12.558248] PM: Cannot get wkup_m3_ipc handle <6>[ 12.594892] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.616830] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.701391] PM: Cannot get wkup_m3_ipc handle <3>[ 13.259390] PM: Cannot get wkup_m3_ipc handle <3>[ 13.284186] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-803485/environment . /lava-803485/environment / # /lava-803485/bin/lava-test-runner /lava-803485/0 /lava-803485/bin/lava-test-runner /lava-803485/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-803485/0/tests/0_dmesg + cat uuid + UUID=803485_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 14.201912] <8>[ 14.268424] <8>[ 14.329175] + set +x / # <8>[ 14.389483] <8>[ 14.391537] # / # export SHELL=/bin/sh. /lava-803485/environment / # . /lava-803485/environment/lava-803485/bin/lava-test-runner /lava-803485/1 / # /lava-803485/bin/lava-test-runner /lava-803485/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-803485/1/tests/1_bootrr + cat uuid + UUID=803485_1.5.2.4.5 <8>[ 14.925783] + set +x + export 'PATH=/opt/bootrr/helpers:/lava-803485/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-803485/1/../bin/lava-test-case <8>[ 16.007044] /lava-803485/1/../bin/lava-test-case <8>[ 16.061759] /lava-803485/1/../bin/lava-test-case <8>[ 16.094229] + set +x