Connected to bbb-patersonc-01 console [channel connected] (~$quit to exit) U-Boot SPL 2020.10 (Apr 28 2023 - 11:09:01 +0100) Trying to boot from MMC2 U-Boot 2020.10 (Apr 28 2023 - 11:09:01 +0100) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... Unable to use mmc 1:1... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2 0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.1.28 (1091 ms) => setenv serverip 192.168.1.1 setenv serverip 192.168.1.1 => tftp 0x82000000 997876/tftp-deploy-0qla_l_3/kernel/zImage tftp 0x82000000 997876/tftp-deploy-0qla_l_3/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.28 Filename '997876/tftp-deploy-0qla_l_3/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 2.3 MiB/s done Bytes transferred = 4604784 (464370 hex) => tftp 0x83000000 997876/tftp-deploy-0qla_l_3/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 997876/tftp-deploy-0qla_l_3/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.28 Filename '997876/tftp-deploy-0qla_l_3/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 2.4 MiB/s done Bytes transferred = 14156799 (d803ff hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 997876/tftp-deploy-0qla_l_3/dtb/am335x-boneblack.dtb tftp 0x88000000 997876/tftp-deploy-0qla_l_3/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 192.168.1.1; our IP address is 192.168.1.28 Filename '997876/tftp-deploy-0qla_l_3/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 2.1 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-08-16 13:08:45 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14156735 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.186-cip37 (KernelCI@build-j14951-arm-gcc-10-omap2plus-defconfig-6g8wq) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 16 12:40:41 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472040K/522240K available (9216K kernel code, 1027K rwdata, 2176K rodata, 1024K init, 279K bss, 33816K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008344] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018567] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030214] Console: colour dummy device 80x30 <3>[ 0.035085] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042145] This ensures that you still see kernel messages. Please <3>[ 0.048871] update your kernel commandline. <6>[ 0.053475] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095549] pid_max: default: 32768 minimum: 301 <6>[ 0.100713] LSM: Security Framework initializing <6>[ 0.105827] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.113644] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.122934] CPU: Testing write buffer coherency: ok <6>[ 0.128299] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.134219] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140717] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147914] rcu: Hierarchical SRCU implementation. <6>[ 0.153728] smp: Bringing up secondary CPUs ... <6>[ 0.158666] smp: Brought up 1 node, 1 CPU <6>[ 0.163116] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169859] CPU: All CPU(s) started in SVC mode. <6>[ 0.175611] devtmpfs: initialized <6>[ 0.191463] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.200002] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210440] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.219118] pinctrl core: initialized pinctrl subsystem <6>[ 0.226684] NET: Registered protocol family 16 <6>[ 0.234271] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260759] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266843] audit: initializing netlink subsys (disabled) <6>[ 0.273905] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273920] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280530] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287247] cpuidle: using governor menu <5>[ 1.157332] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.281544] No ATAGs? <6>[ 1.284172] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.308524] Kprobes globally optimized <6>[ 1.321924] iommu: Default domain type: Translated <6>[ 1.329104] vgaarb: loaded <5>[ 1.332702] SCSI subsystem initialized <6>[ 1.337743] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.343279] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.353006] PTP clock support registered <6>[ 1.358710] clocksource: Switched to clocksource dmtimer <5>[ 2.029588] VFS: Disk quotas dquot_6.6.0 <6>[ 2.033998] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.051044] NET: Registered protocol family 2 <6>[ 2.056106] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.064813] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.073770] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.082065] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.089743] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.096662] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.103696] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.111320] NET: Registered protocol family 1 <6>[ 2.117097] RPC: Registered named UNIX socket transport module. <6>[ 2.123557] RPC: Registered udp transport module. <6>[ 2.128694] RPC: Registered tcp transport module. <6>[ 2.133800] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.140728] PCI: CLS 0 bytes, default 64 <6>[ 2.145774] Trying to unpack rootfs image as initramfs... <6>[ 3.133043] Freeing initrd memory: 13828K <6>[ 3.138963] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.149492] Initialise system trusted keyrings <6>[ 3.154817] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.163045] NFS: Registering the id_resolver key type <5>[ 3.168675] Key type id_resolver registered <5>[ 3.173249] Key type id_legacy registered <6>[ 3.177696] jffs2: version 2.2. (NAND) (SUMMARY) B) 2001-2006 Red Hat, Inc. <5>[ 3.185731] Key type asymmetric registered <5>[ 3.190267] Asymmetric key parser 'x509' registered <6>[ 3.195568] io scheduler mq-deadline registered <6>[ 3.200517] io scheduler kyber registered <3>[ 3.337621] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.346330] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.454366] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.496117] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.567460] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.576209] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.635772] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.644472] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.661881] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.670563] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.733748] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.742312] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.769669] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.784213] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.795157] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.804600] printk: console [ttyS0] enabled <6>[ 3.804600] printk: console [ttyS0] enabled <6>[ 3.813661] printk: bootconsole [omap8250] disabled <6>[ 3.813661] printk: bootconsole [omap8250] disabled <6>[ 3.837410] brd: module loaded <6>[ 3.849861] loop: module loaded <3>[ 3.855334] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.928592] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.971039] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.980968] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.987620] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.993438] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.000990] cpsw 4a100000.ethernet: Detected MACID = f4:b8:98:ab:fa:84 <6>[ 4.010055] i2c /dev entries driver <5>[ 4.015557] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.023497] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.030038] sdhci: Copyright(c) Pierre Ossman <6>[ 4.035387] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.043740] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.053597] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.062075] Initializing XFRM netlink socket <6>[ 4.066876] NET: Registered protocol family 10 <6>[ 4.073314] Segment Routing with IPv6 <6>[ 4.077366] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.084428] NET: Registered protocol family 17 <6>[ 4.089278] NET: Registered protocol family 15 <5>[ 4.094116] Key type dns_resolver registered <6>[ 4.099315] oprofile: using arm/armv7 <6>[ 4.103358] ThumbEE CPU extension supported. <5>[ 4.107933] Registering SWP/SWPB emulation handler <3>[ 4.113480] omap_voltage_late_init: Voltage driver support not added <3>[ 4.120200] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.128632] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.137300] SmartReflex Class3 initialized <6>[ 4.142395] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.151363] Loading compiled-in X.509 certificates <6>[ 4.176364] OMAP GPIO hardware version 0.1 <4>[ 4.209230] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.222917] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.231704] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.238032] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.247998] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.259584] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.268682] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.273848] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.287368] mmc1: new high speed MMC card at address 0001 <6>[ 4.294271] mmcblk1: mmc1:0001 MK2704 3.53 GiB <6>[ 4.299810] mmcblk1boot0: mmc1:0001 MK2704 partition 1 2.00 MiB <6>[ 4.306458] mmcblk1boot1: mmc1:0001 MK2704 partition 2 2.00 MiB <6>[ 4.313064] mmcblk1rpmb: mmc1:0001 MK2704 partition 3 512 KiB, chardev (249:0) <6>[ 4.322587] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.331585] mmcblk1: p1 <6>[ 4.339854] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.430095] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.569232] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.598581] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.628668] Sending DHCP requests ., OK <6>[ 7.672661] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.28 <6>[ 7.680647] IP-Config: Complete: <6>[ 7.684156] device=eth0, hwaddr=f4:b8:98:ab:fa:84, ipaddr=192.168.1.28, mask=255.255.255.0, gw=192.168.1.1 <6>[ 7.694587] host=192.168.1.28, domain=example.org, nis-domain=(none) <6>[ 7.701689] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.701696] nameserver0=192.168.1.1 <6>[ 7.715013] Freeing unused kernel memory: 1024K <6>[ 7.739022] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.971759] udevd[100]: starting version 3.2.9 <5>[ 7.978122] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.986212] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.993326] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.010302] udevd[100]: specified user 'tss' unknown <27>[ 8.015884] udevd[100]: specified group 'tss' unknown <30>[ 8.030929] udevd[101]: starting eudev-3.2.9 <4>[ 8.876609] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.885832] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.902115] remoteproc remoteproc0: wkup_m3 is available <6>[ 9.014182] usbcore: registered new interface driver usbfs <6>[ 9.020211] usbcore: registered new interface driver hub <6>[ 9.025913] usbcore: registered new device driver usb <4>[ 9.160092] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 9.169257] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 9.353510] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.359343] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.568934] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.577527] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.585113] usb usb1: Product: MUSB HDRC host driver <6>[ 9.590384] usb usb1: Manufacturer: Linux 5.10.186-cip37 musb-hcd <6>[ 9.596767] usb usb1: SerialNumber: musb-hdrc.1 <4>[ 9.637965] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.706718] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 9.714502] at24 2-0054: supply vcc not found, using dummy regulator <4>[ 9.890272] at24 2-0055: supply vcc not found, using dummy regulator <3>[ 9.915860] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 9.927332] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 9.969737] hub 1-0:1.0: USB hub found <4>[ 10.032395] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 10.039958] hub 1-0:1.0: 1 port detected <6>[ 10.044586] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 10.054283] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 10.102628] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 10.175219] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.189679] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 10.195095] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <3>[ 10.279723] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.302275] tda998x 0-0070: found TDA19988 <3>[ 10.379554] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.899784] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 10.958370] remoteproc remoteproc0: powering up wkup_m3 <3>[ 11.004268] davinci-mcasp 48038000.mcasp: IRQ common not found <4>[ 11.035536] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.045405] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.051661] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 11.683291] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.718861] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.726522] random: crng init done <6>[ 11.809815] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <3>[ 11.897256] PM: Cannot get wkup_m3_ipc handle <6>[ 11.912173] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 11.939317] PM: Cannot get wkup_m3_ipc handle <6>[ 11.951006] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 12.135665] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.163329] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.214754] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 12.239376] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.342531] PM: Cannot get wkup_m3_ipc handle <3>[ 12.360990] PM: Cannot get wkup_m3_ipc handle <3>[ 12.842302] PM: Cannot get wkup_m3_ipc handle <3>[ 12.874330] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-997876/environment . /lava-997876/environment / # /lava-997876/bin/lava-test-runner /lava-997876/0 /lava-997876/bin/lava-test-runner /lava-997876/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-997876/0/tests/0_dmesg + cat uuid + UUID=997876_1.5.2.4.1 + <8>[ 13.804892] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.870378] <8>[ 13.929889] <8>[ 13.990011] + set +x <8>[ 14.001178] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-997876/environment / # . /lava-997876/environment/lava-997876/bin/lava-test-runner /lava-997876/1 / # /lava-997876/bin/lava-test-runner /lava-997876/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-997876/1/tests/1_bootrr + cat uuid + UUID=997876_1.5.2.4.5 <8>[ 14.563775] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-997876/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-997876/1/../bin/lava-test-case <8>[ 15.668003] /lava-997876/1/../bin/lava-test-case <8>[ 15.722976] /lava-997876/1/../bin/lava-test-case <8>[ 15.755703] /lava-997876/1/../bin/lava-test-case <8>[ 15.816759] /lava-997876/1/../bin/lava-test-case <8>[ 15.867576] /lava-997876/1/../bin/lava-test-case <8>[ 15.908135] /lava-997876/1/../bin/lava-test-case <8>[ 15.958679] /lava-997876/1/../bin/lava-test-case <8>[ 16.024399] /lava-997876/1/../bin/lava-test-case <8>[ 16.065180] /lava-997876/1/../bin/lava-test-case <8>[ 16.114916] /lava-997876/1/../bin/lava-test-case <8>[ 16.155355] /lava-997876/1/../bin/lava-test-case <8>[ 16.205628] /lava-997876/1/../bin/lava-test-case <8>[ 16.245998] /lava-997876/1/../bin/lava-test-case <8>[ 16.286269] /lava-997876/1/../bin/lava-test-case <8>[ 16.327564] /lava-997876/1/../bin/lava-test-case <8>[ 16.377495] /lava-997876/1/../bin/lava-test-case <8>[ 16.419372] /lava-997876/1/../bin/lava-test-case <8>[ 16.470184] /lava-997876/1/../bin/lava-test-case <8>[ 16.519406] /lava-997876/1/../bin/lava-test-case <8>[ 16.559465] /lava-997876/1/../bin/lava-test-case <8>[ 16.609725] /lava-997876/1/../bin/lava-test-case <8>[ 16.659762] /lava-997876/1/../bin/lava-test-case <8>[ 16.701038] /lava-997876/1/../bin/lava-test-case <8>[ 16.751658] /lava-997876/1/../bin/lava-test-case <8>[ 16.792457] /lava-997876/1/../bin/lava-test-case <8>[ 16.842694] /lava-997876/1/../bin/lava-test-case <8>[ 16.883358] /lava-997876/1/../bin/lava-test-case <8>[ 17.960565] /lava-997876/1/../bin/lava-test-case <8>[ 18.001495] /lava-997876/1/../bin/lava-test-case <8>[ 18.052212] /lava-997876/1/../bin/lava-test-case <8>[ 18.093494] /lava-997876/1/../bin/lava-test-case <8>[ 18.144386] /lava-997876/1/../bin/lava-test-case <8>[ 18.184548] /lava-997876/1/../bin/lava-test-case <8>[ 18.235202] /lava-997876/1/../bin/lava-test-case <8>[ 18.275432] /lava-997876/1/../bin/lava-test-case <8>[ 18.326192] /lava-997876/1/../bin/lava-test-case <8>[ 18.366966] /lava-997876/1/../bin/lava-test-case <8>[ 18.417842] /lava-997876/1/../bin/lava-test-case <8>[ 18.458047] /lava-997876/1/../bin/lava-test-case <8>[ 18.508988] /lava-997876/1/../bin/lava-test-case <8>[ 18.549221] /lava-997876/1/../bin/lava-test-case <8>[ 18.599580] /lava-997876/1/../bin/lava-test-case <8>[ 18.640229] /lava-997876/1/../bin/lava-test-case <8>[ 18.690315] /lava-997876/1/../bin/lava-test-case <8>[ 18.730703] /lava-997876/1/../bin/lava-test-case <8>[ 18.780364] /lava-997876/1/../bin/lava-test-case <8>[ 18.820885] /lava-997876/1/../bin/lava-test-case <8>[ 18.870912] /lava-997876/1/../bin/lava-test-case <8>[ 18.911288] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-997876/1/../bin/lava-test-case <8>[ 18.953819] /lava-997876/1/../bin/lava-test-case <8>[ 19.004600] /lava-997876/1/../bin/lava-test-case <8>[ 19.052876] + set +x <8>[ 19.069002] / #