Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 0a:49:8a:15:c7:2e , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 32:12:77:b5:2e:26 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1244118/tftp-deploy-h7mqsf7v/kernel/uImage tftp 0x80080000 1244118/tftp-deploy-h7mqsf7v/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1244118/tftp-deploy-h7mqsf7v/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 3.8 MiB/s done Bytes transferred = 31849024 (1e5fa40 hex) => tftp 0x91000000 1244118/tftp-deploy-h7mqsf7v/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1244118/tftp-deploy-h7mqsf7v/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1244118/tftp-deploy-h7mqsf7v/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 2.7 MiB/s done Bytes transferred = 18909163 (12087eb hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1244118/tftp-deploy-h7mqsf7v/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1244118/tftp-deploy-h7mqsf7v/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1244118/tftp-deploy-h7mqsf7v/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 1000 Bytes/s done Bytes transferred = 19637 (4cb5 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-08-16 13:15:11 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 31848960 Bytes = 30.4 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-08-16 13:15:15 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18909099 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007cb4 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 5.10.186-cip37 (KernelCI@build-j14992-arm64-gcc-10-defconfig-b7wlw) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Wed Aug 16 12:49:45 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3f7b00-0x837e3f9fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu s56664 r8192 d29352 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) [ 0.000000] Memory: 14180204K/14612480K available (14528K kernel code, 2814K rwdata, 7644K rodata, 6016K init, 512K bss, 399508K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080050000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080060000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080070000 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008274] Console: colour dummy device 80x25 [ 0.012772] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023192] pid_max: default: 32768 minimum: 301 [ 0.027866] LSM: Security Framework initializing [ 0.032579] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.040240] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.048962] rcu: Hierarchical SRCU implementation. [ 0.053889] Platform MSI: gic-its@6020000 domain created [ 0.059276] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.066835] fsl-mc MSI: gic-its@6020000 domain created [ 0.072451] EFI services will not be available. [ 0.077184] smp: Bringing up secondary CPUs ... [ 0.081965] Detected PIPT I-cache on CPU1 [ 0.081982] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.081990] GICv3: CPU1: using allocated LPI pending table @0x0000008080080000 [ 0.082004] arch_timer: CPU1: Trapping CNTVCT access [ 0.082013] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.082275] Detected PIPT I-cache on CPU2 [ 0.082290] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.082298] GICv3: CPU2: using allocated LPI pending table @0x0000008080090000 [ 0.082312] arch_timer: CPU2: Trapping CNTVCT access [ 0.082320] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.082577] Detected PIPT I-cache on CPU3 [ 0.082586] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.082593] GICv3: CPU3: using allocated LPI pending table @0x00000080800a0000 [ 0.082603] arch_timer: CPU3: Trapping CNTVCT access [ 0.082610] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.082860] Detected PIPT I-cache on CPU4 [ 0.082875] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.082883] GICv3: CPU4: using allocated LPI pending table @0x00000080800b0000 [ 0.082896] arch_timer: CPU4: Trapping CNTVCT access [ 0.082905] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.083164] Detected PIPT I-cache on CPU5 [ 0.083175] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.083182] GICv3: CPU5: using allocated LPI pending table @0x00000080800c0000 [ 0.083192] arch_timer: CPU5: Trapping CNTVCT access [ 0.083199] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.083452] Detected PIPT I-cache on CPU6 [ 0.083469] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.083477] GICv3: CPU6: using allocated LPI pending table @0x00000080800d0000 [ 0.083492] arch_timer: CPU6: Trapping CNTVCT access [ 0.083501] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.083751] Detected PIPT I-cache on CPU7 [ 0.083762] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.083769] GICv3: CPU7: using allocated LPI pending table @0x00000080800e0000 [ 0.083780] arch_timer: CPU7: Trapping CNTVCT access [ 0.083787] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.083826] smp: Brought up 1 node, 8 CPUs [ 0.297299] SMP: Total of 8 processors activated. [ 0.302031] CPU features: detected: 32-bit EL0 Support [ 0.307207] CPU features: detected: CRC32 instructions [ 0.312376] CPU features: detected: 32-bit EL1 Support [ 0.329064] CPU: All CPU(s) started at EL2 [ 0.333208] alternatives: patching kernel code [ 0.338354] devtmpfs: initialized [ 0.342986] KASLR enabled [ 0.345686] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.355502] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.362858] pinctrl core: initialized pinctrl subsystem [ 0.368566] DMI not present or invalid. [ 0.372707] NET: Registered protocol family 16 [ 0.377859] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.385342] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.393672] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.401740] audit: initializing netlink subsys (disabled) [ 0.407260] audit: type=2000 audit(0.268:1): state=initialized audit_enabled=0 res=1 [ 0.407608] thermal_sys: Registered thermal governor 'step_wise' [ 0.415051] thermal_sys: Registered thermal governor 'power_allocator' [ 0.421440] cpuidle: using governor menu [ 0.432030] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.438935] ASID allocator initialised with 32768 entries [ 0.444844] Serial: AMBA PL011 UART driver [ 0.455975] Machine: Freescale Layerscape 2088A RDB Board [ 0.461409] SoC family: QorIQ LS2088A [ 0.465086] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.477664] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.484597] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.491337] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.498073] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.505444] cryptd: max_cpu_qlen set to 1000 [ 0.510807] ACPI: Interpreter disabled. [ 0.515305] iommu: Default domain type: Translated [ 0.520301] vgaarb: loaded [ 0.523128] SCSI subsystem initialized [ 0.527033] usbcore: registered new interface driver usbfs [ 0.532562] usbcore: registered new interface driver hub [ 0.537912] usbcore: registered new device driver usb [ 0.543196] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.550570] i2c i2c-0: IMX I2C adapter registered [ 0.555443] pps_core: LinuxPPS API ver. 1 registered [ 0.560432] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.569637] PTP clock support registered [ 0.573643] EDAC MC: Ver: 3.0.0 [ 0.577267] fsl-ifc 2240000.ifc: Freescale Integrated Flash Controller [ 0.583848] fsl-ifc 2240000.ifc: IFC version 2.0, 8 banks [ 0.589346] FPGA manager framework [ 0.592785] Advanced Linux Sound Architecture Driver Initialized. [ 0.599223] clocksource: Switched to clocksource arch_sys_counter [ 0.605426] VFS: Disk quotas dquot_6.6.0 [ 0.609392] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.616377] pnp: PnP ACPI: disabled [ 0.622085] NET: Registered protocol family 2 [ 0.626887] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.637952] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.646718] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.655308] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.663197] TCP: Hash tables configured (established 131072 bind 65536) [ 0.669941] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.676941] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.684437] NET: Registered protocol family 1 [ 0.689002] RPC: Registered named UNIX socket transport module. [ 0.694961] RPC: Registered udp transport module. [ 0.699697] RPC: Registered tcp transport module. [ 0.704428] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.710905] PCI: CLS 0 bytes, default 64 [ 0.714911] Unpacking initramfs... [ 1.170407] Freeing initrd memory: 18460K [ 1.174885] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.182844] kvm [1]: IPA Size Limit: 44 bits [ 1.187605] kvm [1]: vgic-v2@c0e0000 [ 1.191206] kvm [1]: GIC system register CPU interface enabled [ 1.197219] kvm [1]: vgic interrupt IRQ9 [ 1.201266] kvm [1]: Hyp mode initialized successfully [ 1.208279] Initialise system trusted keyrings [ 1.212816] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 1.221547] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.227670] NFS: Registering the id_resolver key type [ 1.232763] Key type id_resolver registered [ 1.236967] Key type id_legacy registered [ 1.241027] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.247768] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.255273] 9p: Installing v9fs 9p2000 file system support [ 1.281584] Key type asymmetric registered [ 1.285702] Asymmetric key parser 'x509' registered [ 1.290618] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.298057] io scheduler mq-deadline registered [ 1.302611] io scheduler kyber registered [ 1.310306] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.317677] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 1.326261] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 1.334910] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 1.341650] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.347164] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.353378] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.363983] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.370028] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 1.376333] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 1.382636] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 1.389757] pci 0000:00:00.0: supports D1 D2 [ 1.394047] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.400715] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 1.406820] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 1.413508] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 1.420194] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 1.425837] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 1.432595] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 1.439935] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.455700] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.462880] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.470064] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.477677] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.484941] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.491155] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.498341] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.505954] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.513140] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.520324] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.526462] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.531714] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.537842] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.545178] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.552545] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 1.561130] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 1.569771] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 1.576513] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.582029] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.591039] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.601635] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.607685] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 1.614798] pci 0001:00:00.0: supports D1 D2 [ 1.619088] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.626081] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 1.633695] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.639459] EINJ: ACPI disabled. [ 1.648077] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.655318] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 16, base_baud = 21875000) is a 16550A [ 1.664380] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 16, base_baud = 21875000) is a 16550A [ 1.673238] printk: console [ttyS1] enabled [ 1.673238] printk: console [ttyS1] enabled [ 1.681620] printk: bootconsole [uart8250] disabled [ 1.681620] printk: bootconsole [uart8250] disabled [ 1.691604] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 17, base_baud = 21875000) is a 16550A [ 1.700593] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 17, base_baud = 21875000) is a 16550A [ 1.709581] SuperH (H)SCI(F) driver initialized [ 1.714304] msm_serial: driver initialized [ 1.719163] arm-smmu 5000000.iommu: probing hardware configuration... [ 1.725603] arm-smmu 5000000.iommu: SMMUv2 with: [ 1.730215] arm-smmu 5000000.iommu: stage 1 translation [ 1.735522] arm-smmu 5000000.iommu: stage 2 translation [ 1.740828] arm-smmu 5000000.iommu: nested translation [ 1.746048] arm-smmu 5000000.iommu: coherent table walk [ 1.751356] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 1.758489] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 1.765013] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 1.771449] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.777883] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.788305] loop: module loaded [ 1.791847] megasas: 07.714.04.00-rc1 [ 1.795970] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 1.803499] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 1.810909] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 1.818622] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.827584] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.837760] scsi host0: ahci-qoriq [ 1.841264] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 104 [ 1.849330] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 1.856860] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 1.864269] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 1.871965] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.880923] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.890828] scsi host1: ahci-qoriq [ 1.894299] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 105 [ 1.902593] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 1.911861] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 1.921948] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.927091] Amd/Fujitsu Extended Query version 1.3. [ 1.932140] number of CFI chips: 1 [ 1.952145] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 1.958510] nand: Micron MT29F16G08ABABAWP [ 1.962605] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 1.971361] Bad block table found at page 524160, version 0x01 [ 1.979113] Bad block table found at page 524032, version 0x01 [ 1.999624] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 2.007628] spi-nor spi0.0: unrecognized JEDEC id bytes: e3 c7 8f 1e 3c 78 [ 2.014835] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.021723] spi-nor: probe of spi1.0 failed with error -2 [ 2.028215] tun: Universal TUN/TAP device driver, 1.6 [ 2.033557] thunder_xcv, ver 1.0 [ 2.036824] thunder_bgx, ver 1.0 [ 2.040063] nicpf, ver 1.0 [ 2.043213] hclge is initializing [ 2.046534] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.053751] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.059074] e1000: Intel(R) PRO/1000 Network Driver [ 2.063948] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 2.069704] e1000e: Intel(R) PRO/1000 Network Driver [ 2.074664] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.080660] e1000e 0000:01:00.0: Adding to iommu group 0 [ 2.086328] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.143666] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.161388] ata1: SATA link down (SStatus 0 SControl 300) [ 2.205155] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 2.213080] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.217384] ata2: SATA link down (SStatus 0 SControl 300) [ 2.219966] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 2.232076] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.237471] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.243055] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 2.249318] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 2.255399] sky2: driver version 1.30 [ 2.259463] VFIO - User Level meta-driver version: 0.3 [ 2.265815] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.272361] ehci-pci: EHCI PCI platform driver [ 2.276816] ehci-platform: EHCI generic platform driver [ 2.282086] ehci-orion: EHCI orion driver [ 2.286127] ehci-exynos: EHCI Exynos driver [ 2.290339] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.296522] ohci-pci: OHCI PCI platform driver [ 2.300973] ohci-platform: OHCI generic platform driver [ 2.306232] ohci-exynos: OHCI Exynos driver [ 2.310558] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.316048] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 2.323780] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.333191] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x03100000 [ 2.339263] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.344747] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 2.352402] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.359134] hub 1-0:1.0: USB hub found [ 2.362892] hub 1-0:1.0: 1 port detected [ 2.366929] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.375180] hub 2-0:1.0: USB hub found [ 2.378934] hub 2-0:1.0: 1 port detected [ 2.382985] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.388477] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 2.396202] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.405608] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x03110000 [ 2.411678] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.417162] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 2.424818] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.431506] hub 3-0:1.0: USB hub found [ 2.435261] hub 3-0:1.0: 1 port detected [ 2.439293] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.447540] hub 4-0:1.0: USB hub found [ 2.451296] hub 4-0:1.0: 1 port detected [ 2.455487] usbcore: registered new interface driver usb-storage [ 2.462500] i2c /dev entries driver [ 2.467181] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.472349] rtc-ds3232: probe of 2-0068 failed with error -11 [ 2.478110] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.483032] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.487952] i2c i2c-0: Added multiplexed i2c bus 4 [ 2.492815] i2c i2c-0: Added multiplexed i2c bus 5 [ 2.497671] i2c i2c-0: Added multiplexed i2c bus 6 [ 2.502527] i2c i2c-0: Added multiplexed i2c bus 7 [ 2.507390] i2c i2c-0: Added multiplexed i2c bus 8 [ 2.512181] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 2.520554] sp805-wdt c000000.wdt: registration successful [ 2.526116] sp805-wdt c010000.wdt: registration successful [ 2.531669] sp805-wdt c100000.wdt: registration successful [ 2.537229] sp805-wdt c110000.wdt: registration successful [ 2.542783] sp805-wdt c200000.wdt: registration successful [ 2.548337] sp805-wdt c210000.wdt: registration successful [ 2.553892] sp805-wdt c300000.wdt: registration successful [ 2.559452] sp805-wdt c310000.wdt: registration successful [ 2.566438] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 2.574904] sdhci: Secure Digital Host Controller Interface driver [ 2.581091] sdhci: Copyright(c) Pierre Ossman [ 2.585651] Synopsys Designware Multimedia Card Interface Driver [ 2.592022] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.598566] ledtrig-cpu: registered to indicate activity on CPUs [ 2.605153] usbcore: registered new interface driver usbhid [ 2.610724] usbhid: USB HID core driver [ 2.615747] optee: probing for conduit method. [ 2.620190] optee: api uid mismatch [ 2.623245] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.623680] optee: probe of firmware:optee failed with error -22 [ 2.638192] NET: Registered protocol family 17 [ 2.642714] 9pnet: Installing 9P2000 support [ 2.647007] Key type dns_resolver registered [ 2.651417] registered taskstats version 1 [ 2.655514] Loading compiled-in X.509 certificates [ 2.661863] pcieport 0000:00:00.0: Adding to iommu group 1 [ 2.667618] pcieport 0000:00:00.0: PME: Signaling with IRQ 112 [ 2.673654] pcieport 0001:00:00.0: Adding to iommu group 2 [ 2.679407] pcieport 0001:00:00.0: PME: Signaling with IRQ 116 [ 5.288235] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 5.323251] Sending DHCP requests ..., OK [ 13.455294] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 13.462870] IP-Config: Complete: [ 13.466105] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 13.476115] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 13.482907] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 13.482912] nameserver0=172.16.1.4 [ 13.493130] ALSA device list: [ 13.496113] No soundcards found. [ 13.501997] Freeing unused kernel memory: 6016K [ 13.511285] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 13.547976] udevd[185]: starting version 3.2.9 [ 13.552729] random: udevd: uninitialized urandom read (16 bytes read) [ 13.559247] random: udevd: uninitialized urandom read (16 bytes read) [ 13.565710] random: udevd: uninitialized urandom read (16 bytes read) [ 13.574135] udevd[185]: specified user 'tss' unknown [ 13.579137] udevd[185]: specified group 'tss' unknown [ 13.585041] udevd[186]: starting eudev-3.2.9 [ 13.692082] udevd[196]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 13.701007] udevd[196]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 13.701233] lm90 4-004c: supply vcc not found, using dummy regulator [ 13.715624] ina2xx 3-0040: error configuring the device: -11 [ 14.219225] lm90 4-004c: Failed to initialize device [ 14.224274] lm90: probe of 4-004c failed with error -110 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 14.288722] NET: Registered protocol family 10 [ 14.293917] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1244118/environment . /lava-1244118/environment / # /lava-1244118/bin/lava-test-runner /lava-1244118/0 /lava-1244118/bin/lava-test-runner /lava-1244118/0 + export 'TESTRUN_[ 15.013362] ID=0_dmesg' + cd /lava-1244118/0/tests/0_dmesg + cat uuid + UUID=1244118_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 15.032260] [ 15.053110] [ 15.071773] + [ 15.080806] set +x # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1244118/environment / # . /lava-1244118/environment/lava-1244118/bin/lava-test-runner /lava-1244118/1 / # /lava-1244118/bin/lava-test-runner /lava-1244118/1 + export 'TESTRUN_ID=1_bootrr' + [ 15.517262] cd /lava-1244118/1/tests/1_bootrr + cat uuid + UUID=1244118_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1244118/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1244118/1/../bin/lava-test-case [ 16.538523] /lava-1244118/1/../bin/lava-test-case [ 16.556758] /lava-1244118/1/../bin/lava-test-case [ 16.570114] + set +x [ 16.580959] / #