Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.07 (Sep 18 2019 - 15:55:50 +0200) DRAM: 512 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2019.07 (Sep 18 2019 - 15:55:50 +0200) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Olimex A10-OLinuXino-LIME I2C: ready DRAM: 512 MiB MMC: mmc@1c0f000: 0 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: eth0: ethernet@1c0b000 starting USB... Bus usb@1c14000: USB EHCI 1.00 Bus usb@1c14400: USB OHCI 1.0 Bus usb@1c1c000: USB EHCI 1.00 Bus usb@1c1c400: USB OHCI 1.0 scanning bus usb@1c14000 for devices... 1 USB Device(s) found scanning bus usb@1c14400 for devices... 1 USB Device(s) found scanning bus usb@1c1c000 for devices... 1 USB Device(s) found scanning bus usb@1c1c400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ENET Speed is 100 Mbps - FULL duplex connection BOOTP broadcast 1 DHCP client bound to address 10.201.4.69 (9 ms) => setenv serverip 10.201.1.8 setenv serverip 10.201.1.8 => tftp 0x42000000 3222080/tftp-deploy-xl_q82f5/kernel/zImage tftp 0x42000000 3222080/tftp-deploy-xl_q82f5/kernel/zImage Using ethernet@1c0b000 device TFTP from server 10.201.1.8; our IP address is 10.201.4.69 Filename '3222080/tftp-deploy-xl_q82f5/kernel/zImage'. Load address: 0x42000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################### 280.3 KiB/s done Bytes transferred = 4844792 (49ecf8 hex) => tftp 0x43300000 3222080/tftp-deploy-xl_q82f5/ramdisk/ramdisk.cpio.gz.uboot tftp 0x43300000 3222080/tftp-deploy-xl_q82f5/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@1c0b000 device TFTP from server 10.201.1.8; our IP address is 10.201.4.69 Filename '3222080/tftp-deploy-xl_q82f5/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x43300000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##########################T T T T ####################################### ########################################################## 193.4 KiB/s done Bytes transferred = 7950283 (794fcb hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x43000000 3222080/tftp-deploy-xl_q82f5/dtb/sun4i-a10-olinuxino-lime.dtb tftp 0x43000000 3222080/tftp-deploy-xl_q82f5/dtb/sun4i-a10-olinuxino-lime.dtb Using ethernet@1c0b000 device TFTP from server 10.201.1.8; our IP address is 10.201.4.69 Filename '3222080/tftp-deploy-xl_q82f5/dtb/sun4i-a10-olinuxino-lime.dtb'. Load address: 0x43000000 Loading: *##### 110.4 KiB/s done Bytes transferred = 22240 (56e0 hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x42000000 0x43300000 0x43000000 bootz 0x42000000 0x43300000 0x43000000 ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7950219 Bytes = 7.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Using Device Tree in place at 43000000, end 430086df Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.162-cip24-rt10 (KernelCI@build-j927118-arm-gcc-10-sunxi-defconfig-w7ljm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Jan 27 00:40:54 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Olimex A10-OLinuXino-LIME [ 0.000000] earlycon: uart0 at MMIO32 0x01c28000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] Reserved memory: created CMA memory pool at 0x4a000000, size 96 MiB [ 0.000000] OF: reserved mem: initialized node default-pool, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] Normal zone: 1024 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 131072 pages, LIFO batch:31 [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 11 pages/cpu s14924 r8192 d21940 u45056 [ 0.000000] pcpu-alloc: s14924 r8192 d21940 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 400924K/524288K available (7168K kernel code, 916K rwdata, 1952K rodata, 1024K init, 262K bss, 25060K reserved, 98304K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000003] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008329] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018385] Console: colour dummy device 80x30 <6>[ 0.023376] Calibrating delay loop... 910.13 BogoMIPS (lpj=4550656) <6>[ 0.114877] pid_max: default: 32768 minimum: 301 <6>[ 0.120026] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.127788] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.136664] CPU: Testing write buffer coherency: ok <3>[ 0.142117] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.152357] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.158706] Setting up static identity map for 0x40100000 - 0x40100060 <6>[ 0.166019] rcu: Hierarchical SRCU implementation. <6>[ 0.171828] smp: Bringing up secondary CPUs ... <6>[ 0.176863] smp: Brought up 1 node, 1 CPU <6>[ 0.181258] SMP: Total of 1 processors activated (910.13 BogoMIPS). <6>[ 0.187936] CPU: All CPU(s) started in SVC mode. <6>[ 0.193390] devtmpfs: initialized <6>[ 0.202218] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.210509] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.221136] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.232954] pinctrl core: initialized pinctrl subsystem <6>[ 0.240067] NET: Registered protocol family 16 <6>[ 0.246631] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.254935] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.255175] hw-breakpoint: debug architecture 0x4 unsupported. <5>[ 0.290158] SCSI subsystem initialized <7>[ 0.294642] libata version 3.00 loaded. <6>[ 0.299230] usbcore: registered new interface driver usbfs <6>[ 0.305311] usbcore: registered new interface driver hub <6>[ 0.311098] usbcore: registered new device driver usb <6>[ 0.316725] mc: Linux media interface: v0.10 <6>[ 0.321529] videodev: Linux video capture interface: v2.00 <6>[ 0.327652] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.333148] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.342782] PTP clock support registered <6>[ 0.347544] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.355261] clocksource: Switched to clocksource timer <6>[ 0.368878] NET: Registered protocol family 2 <6>[ 0.373978] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.382421] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 0.391536] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.399786] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.407430] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.414291] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.421287] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.429020] NET: Registered protocol family 1 <6>[ 0.434609] RPC: Registered named UNIX socket transport module. <6>[ 0.441151] RPC: Registered udp transport module. <6>[ 0.446372] RPC: Registered tcp transport module. <6>[ 0.451460] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.458608] Unpacking initramfs... <6>[ 0.972789] Freeing initrd memory: 7764K <6>[ 0.977622] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <6>[ 0.987776] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <5>[ 1.001208] NFS: Registering the id_resolver key type <5>[ 1.006937] Key type id_resolver registered <5>[ 1.011598] Key type id_legacy registered <6>[ 1.016079] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.024129] io scheduler mq-deadline registered <6>[ 1.029053] io scheduler kyber registered <3>[ 1.034063] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO <6>[ 1.043869] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver <6>[ 1.105822] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled <4>[ 1.114670] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pb not found, using dummy regulator <6>[ 1.124528] printk: console [ttyS0] disabled <6>[ 1.149543] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 39, base_baud = 1500000) is a U6_16550A <6>[ 1.159352] printk: console [ttyS0] enabled <6>[ 1.159352] printk: console [ttyS0] enabled <6>[ 1.168482] printk: bootconsole [uart0] disabled <6>[ 1.168482] printk: bootconsole [uart0] disabled <6>[ 1.182786] sun4i-drm display-engine: bound 1e00000.display-frontend (ops 0xc084c738) <6>[ 1.191091] sun4i-drm display-engine: bound 1e20000.display-frontend (ops 0xc084c738) <6>[ 1.199566] sun4i-drm display-engine: bound 1e60000.display-backend (ops 0xc084bed4) <3>[ 1.207602] sun4i-drm display-engine: attempt to add DMA range to existing map <6>[ 1.215431] sun4i-drm display-engine: bound 1e40000.display-backend (ops 0xc084bed4) <6>[ 1.223859] sun4i-drm display-engine: No panel or bridge found... RGB output disabled <6>[ 1.231994] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc084a834) <6>[ 1.240311] sun4i-drm display-engine: No panel or bridge found... RGB output disabled <6>[ 1.248439] sun4i-drm display-engine: bound 1c0d000.lcd-controller (ops 0xc084a834) <6>[ 1.257732] sun4i-drm display-engine: bound 1c16000.hdmi (ops 0xc084ce58) <6>[ 1.265580] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 <6>[ 1.273649] sun4i-drm display-engine: [drm] Cannot find any crtc or sizes <6>[ 1.285026] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 <6>[ 1.291602] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 <6>[ 1.298191] lima 1c40000.gpu: l2 cache 32K, 4-way, 64byte cache line, 64bit external bus <6>[ 1.307114] lima 1c40000.gpu: bus rate = 152000000 <6>[ 1.312178] lima 1c40000.gpu: mod rate = 384000000 <6>[ 1.317712] [drm] Initialized lima 1.1.0 20191231 for 1c40000.gpu on minor 1 <4>[ 1.325788] ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator <4>[ 1.333695] ahci-sunxi 1c18000.sata: supply phy not found, using dummy regulator <4>[ 1.343130] sun4i-mdio 1c0b080.mdio: supply phy not found, using dummy regulator <6>[ 1.412638] CAN device driver interface <4>[ 1.417206] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator <6>[ 1.427843] sun4i-emac 1c0b000.ethernet: eth0: at (ptrval), IRQ 19 MAC: 02:49:09:40:ab:3d <6>[ 1.437209] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.444001] ehci-platform: EHCI generic platform driver <6>[ 1.450054] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.456571] ohci-platform: OHCI generic platform driver <6>[ 1.464240] sunxi-rtc 1c20d00.rtc: registered as rtc0 <6>[ 1.469720] sunxi-rtc 1c20d00.rtc: setting system clock to 2010-01-01T00:01:12 UTC (1262304072) <6>[ 1.478836] i2c /dev entries driver <6>[ 1.483649] axp20x-i2c 1-0034: AXP20x variant AXP209 found <4>[ 1.495689] axp20x-gpio: Failed to locate of_node [id: -1] <6>[ 1.501916] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-1/1-0034/axp20x-pek/input/input0 <4>[ 1.520009] axp20x-regulator axp20x-regulator: regulators node not found <6>[ 1.527203] ldo1: supplied by regulator-dummy <6>[ 1.532473] ldo2: supplied by regulator-dummy <6>[ 1.537773] ldo3: supplied by regulator-dummy <6>[ 1.542574] ldo4: supplied by regulator-dummy <6>[ 1.547847] ldo5: supplied by regulator-dummy <6>[ 1.553081] dcdc2: supplied by regulator-dummy <6>[ 1.558430] dcdc3: supplied by regulator-dummy <4>[ 1.563218] axp20x-adc: Failed to locate of_node [id: -1] <4>[ 1.569068] axp20x-battery-power-supply: Failed to locate of_node [id: -1] <4>[ 1.576345] axp20x-ac-power-supply: Failed to locate of_node [id: -1] <4>[ 1.583148] axp20x-usb-power-supply: Failed to locate of_node [id: -1] <6>[ 1.590071] axp20x-i2c 1-0034: AXP20X driver loaded <6>[ 1.598404] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) <4>[ 1.608346] sun4i-pinctrl 1c20800.pinctrl: supply vcc-ph not found, using dummy regulator <6>[ 1.617591] sun4i-ss 1c15000.crypto-engine: Die ID 7 <4>[ 1.623186] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator <6>[ 1.632787] sunxi-mmc 1c0f000.mmc: Got CD GPIO <6>[ 1.640017] usbcore: registered new interface driver usbhid <6>[ 1.645942] usbhid: USB HID core driver <6>[ 1.650723] cedrus 1c0e000.video-codec: Device registered as /dev/video0 <6>[ 1.662929] NET: Registered protocol family 17 <6>[ 1.667814] can: controller area network core <6>[ 1.672522] NET: Registered protocol family 29 <6>[ 1.677258] can: raw protocol <6>[ 1.680491] can: broadcast manager protocol <6>[ 1.684938] can: netlink gateway - max_hops=1 <5>[ 1.689814] Key type dns_resolver registered <5>[ 1.694420] Registering SWP/SWPB emulation handler <6>[ 1.700029] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 2048 KB <6>[ 1.707619] printk: console [ttyS0]: printing thread started <4>[ 1.727427] sun4i-pinctrl 1c20800.pinctrl: supply vcc-pc not found, using dummy regulator <4>[ 1.730806] ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator <4>[ 1.730983] ahci-sunxi 1c18000.sata: supply phy not found, using dummy regulator <4>[ 1.789906] mmc0: host does not support reading read-only switch, assuming write-enable <6>[ 1.791820] mmc0: new high speed SDHC card at address 0007 <6>[ 1.792741] mmcblk0: mmc0:0007 SD16G 14.5 GiB <6>[ 1.796387] mmcblk0: p1 <6>[ 1.825337] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP <4>[ 1.825354] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 <6>[ 1.825421] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.825438] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc <6>[ 1.826547] scsi host0: ahci-sunxi <6>[ 1.826890] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 29 <6>[ 1.827819] ehci-platform 1c14000.usb: EHCI Host Controller <6>[ 1.827881] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 <6>[ 1.828339] ehci-platform 1c14000.usb: irq 25, io mem 0x01c14000 <6>[ 1.900432] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.901306] hub 1-0:1.0: USB hub found <6>[ 1.901364] hub 1-0:1.0: 1 port detected <6>[ 1.902561] ehci-platform 1c1c000.usb: EHCI Host Controller <6>[ 1.902594] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.902946] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 <6>[ 1.940044] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.941078] hub 2-0:1.0: USB hub found <6>[ 1.941130] hub 2-0:1.0: 1 port detected <6>[ 1.942290] ohci-platform 1c14400.usb: Generic Platform OHCI controller <6>[ 1.942322] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 <6>[ 1.942662] ohci-platform 1c14400.usb: irq 26, io mem 0x01c14400 <6>[ 2.010041] hub 3-0:1.0: USB hub found <6>[ 2.010091] hub 3-0:1.0: 1 port detected <6>[ 2.011273] ohci-platform 1c1c400.usb: Generic Platform OHCI controller <6>[ 2.011310] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 <6>[ 2.011640] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 <6>[ 2.081208] hub 4-0:1.0: USB hub found <6>[ 2.081287] hub 4-0:1.0: 1 port detected <4>[ 2.082913] usb_phy_generic usb_phy_generic.0.auto: supply vcc not found, using dummy regulator <4>[ 2.083137] usb_phy_generic usb_phy_generic.0.auto: dummy supplies not allowed for exclusive requests <6>[ 2.084064] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver <6>[ 2.084111] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5 <6>[ 2.085442] hub 5-0:1.0: USB hub found <6>[ 2.131868] hub 5-0:1.0: 1 port detected <6>[ 2.159883] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.425298] sun4i-emac 1c0b000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <5>[ 2.456105] Sending DHCP requests ., OK <6>[ 2.495289] IP-Config: Got DHCP answer from 10.201.1.3, my address is 10.201.4.69 <6>[ 2.495310] IP-Config: Complete: <6>[ 2.495315] device=eth0, hwaddr=02:49:09:40:ab:3d, ipaddr=10.201.4.69, mask=255.255.0.0, gw=10.201.1.3 <6>[ 2.495333] host=10.201.4.69, domain=, nis-domain=(none) <6>[ 2.495342] bootserver=10.201.1.3, rootserver=10.201.1.3, rootpath= <6>[ 2.495352] nameserver0=10.1.1.1 <6>[ 2.495947] ALSA device list: <6>[ 2.495960] No soundcards found. <6>[ 2.499115] Freeing unused kernel memory: 1024K <6>[ 2.566995] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 2.748924] udevd[98]: starting version 3.2.9 <5>[ 2.749954] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 2.750323] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 2.750447] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 2.785193] udevd[98]: specified user 'tss' unknown <27>[ 2.785875] udevd[98]: specified group 'tss' unknown <30>[ 2.789531] udevd[99]: starting eudev-3.2.9 done Saving random seed: OK <5>[ 4.304549] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 4.403001] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-3222080/environment . /lava-3222080/environment / # /lava-3222080/bin/lava-test-runner /lava-3222080/0 /lava-3222080/bin/lava-test-runner /lava-3222080/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-3222080/0/tests/0_dmesg + cat uuid + UUID=3222080_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 5.067812] <8>[ 5.116564] <8>[ 5.163043] + set +x / # <8>[ 5.209730] <8>[ 5.211342] # / # export SHELL=/bin/sh. /lava-3222080/environment / # . /lava-3222080/environment/lava-3222080/bin/lava-test-runner /lava-3222080/1 / # /lava-3222080/bin/lava-test-runner /lava-3222080/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-3222080/1/tests/1_bootrr + cat uuid + UUID=3222080_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/l<8>[ 5.753227] ibexec/bootrr/helpers:/lava-3222080/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-3222080/1/../bin/lava-test-case <8>[ 5.815518] /lava-3222080/1/../bin/lava-test-case <8>[ 5.859092] /lava-3222080/1/../bin/lava-test-case <8>[ 5.886508] + set +x