[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11090588/tftp-deploy-k_qirw_m/kernel/zImage tftp 0x10000000 11090588/tftp-deploy-k_qirw_m/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11090588/tftp-deploy-k_qirw_m/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 3 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 11090588/tftp-deploy-k_qirw_m/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11090588/tftp-deploy-k_qirw_m/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11090588/tftp-deploy-k_qirw_m/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 3.2 MiB/s done Bytes transferred = 16077697 (f55381 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11090588/tftp-deploy-k_qirw_m/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11090588/tftp-deploy-k_qirw_m/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11090588/tftp-deploy-k_qirw_m/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16077633 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.186-cip37-rt15 (KernelCI@build-j2434-arm-gcc-10-multi-v7-defconfig-p9z66) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Jul 15 00:24:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] pcpu-alloc: s33676 r8192 d23668 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932632K/1048576K available (14336K kernel code, 2332K rwdata, 5360K rodata, 2048K init, 417K bss, 50408K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000000] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008089] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021695] Console: colour dummy device 80x30 <6>[ 0.023588] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034261] pid_max: default: 32768 minimum: 301 <6>[ 0.039290] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046714] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055331] CPU: Testing write buffer coherency: ok <6>[ 0.059843] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065386] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071788] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079431] rcu: Hierarchical SRCU implementation. <6>[ 0.086407] EFI services will not be available. <6>[ 0.088650] smp: Bringing up secondary CPUs ... <6>[ 0.093954] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099047] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105280] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110269] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116496] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121491] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.126925] smp: Brought up 1 node, 4 CPUs <6>[ 0.131148] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.137695] CPU: All CPU(s) started in SVC mode. <6>[ 0.143111] devtmpfs: initialized <6>[ 0.153662] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159010] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168874] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179091] pinctrl core: initialized pinctrl subsystem <6>[ 0.183577] DMI not present or invalid. <6>[ 0.186682] NET: Registered protocol family 16 <6>[ 0.194047] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200695] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200874] cpuidle: using governor menu <6>[ 0.208958] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.390754] vdd1p1: supplied by regulator-dummy <6>[ 0.399997] vdd3p0: supplied by regulator-dummy <6>[ 0.409178] vdd2p5: supplied by regulator-dummy <6>[ 0.418384] vddarm: supplied by regulator-dummy <6>[ 0.427730] vddpu: supplied by regulator-dummy <6>[ 0.436701] vddsoc: supplied by regulator-dummy <6>[ 0.771198] No ATAGs? <6>[ 0.771382] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.779162] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.789321] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.799587] Serial: AMBA PL011 UART driver <6>[ 0.803248] printk: console [ramoops-1] enabled <6>[ 0.806104] pstore: Registered ramoops as persistent store backend <6>[ 0.812311] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.850411] iommu: Default domain type: Translated <6>[ 0.853125] vgaarb: loaded <5>[ 0.856571] SCSI subsystem initialized <7>[ 0.860033] libata version 3.00 loaded. <6>[ 0.863991] usbcore: registered new interface driver usbfs <6>[ 0.869571] usbcore: registered new interface driver hub <6>[ 0.875098] usbcore: registered new device driver usb <6>[ 0.881917] i2c i2c-0: IMX I2C adapter registered <6>[ 0.886740] i2c i2c-1: IMX I2C adapter registered <6>[ 0.891111] i2c i2c-2: IMX I2C adapter registered <6>[ 0.896619] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.900466] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.909899] PTP clock support registered <6>[ 0.917600] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.982704] NET: Registered protocol family 2 <6>[ 1.984912] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.993330] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.000805] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.008845] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.016277] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.022997] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.029690] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.037115] NET: Registered protocol family 1 <6>[ 2.042243] RPC: Registered named UNIX socket transport module. <6>[ 2.047763] RPC: Registered udp transport module. <6>[ 2.052684] RPC: Registered tcp transport module. <6>[ 2.057664] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.064352] PCI: CLS 0 bytes, default 64 <6>[ 2.069023] Trying to unpack rootfs image as initramfs... <6>[ 3.431222] Freeing initrd memory: 15704K <4>[ 3.433201] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.440523] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.450279] Initialise system trusted keyrings <6>[ 3.453441] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.465798] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.469859] NFS: Registering the id_resolver key type <5>[ 3.474386] Key type id_resolver registered <5>[ 3.478809] Key type id_legacy registered <6>[ 3.483151] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.490030] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.497709] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.502734] Key type asymmetric registered <5>[ 3.506629] Asymmetric key parser 'x509' registered <6>[ 3.511824] bounce: pool size: 64 pages <6>[ 3.515881] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.523528] io scheduler mq-deadline registered <6>[ 3.528305] io scheduler kyber registered <6>[ 3.571792] mxs-dma 110000.dma-apbh: initialized <4>[ 3.578535] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.585445] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.654977] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.663206] SuperH (H)SCI(F) driver initialized <6>[ 3.666160] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.675052] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.682988] printk: console [ttymxc1] enabled <6>[ 3.687494] printk: bootconsole [ec_imx21] disabled <6>[ 3.682988] printk: console [ttymxc1] enabled <6>[ 3.687494] printk: bootconsole [ec_imx21] disabled <6>[ 3.694100] msm_serial: driver initialized <6>[ 3.694353] STMicroelectronics ASC driver initialized <6>[ 3.696259] STM32 USART driver initialized <4>[ 3.706581] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.706733] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.707124] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.715927] brd: module loaded <6>[ 3.725853] loop: module loaded <6>[ 3.729865] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.729881] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.729890] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.729899] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.729976] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.730145] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.730213] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.733043] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.733072] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.733089] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.734602] scsi host0: ahci-imx <6>[ 3.734976] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.747396] CAN device driver interface <6>[ 3.748784] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.752332] pps pps0: new PPS source ptp0 <6>[ 3.785585] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.787075] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.787081] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.787139] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.787144] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.793330] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.793375] usbcore: registered new interface driver pegasus <6>[ 3.793417] usbcore: registered new interface driver asix <6>[ 3.793454] usbcore: registered new interface driver ax88179_178a <6>[ 3.793487] usbcore: registered new interface driver cdc_ether <6>[ 3.793530] usbcore: registered new interface driver smsc75xx <6>[ 3.793581] usbcore: registered new interface driver smsc95xx <6>[ 3.793617] usbcore: registered new interface driver net1080 <6>[ 3.793649] usbcore: registered new interface driver cdc_subset <6>[ 3.793681] usbcore: registered new interface driver zaurus <6>[ 3.793753] usbcore: registered new interface driver cdc_ncm <6>[ 3.797304] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.797311] ehci-pci: EHCI PCI platform driver <6>[ 3.797347] ehci-platform: EHCI generic platform driver <6>[ 3.797662] ehci-orion: EHCI orion driver <6>[ 3.797895] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.798082] ehci-st: EHCI STMicroelectronics driver <6>[ 3.798263] ehci-exynos: EHCI Exynos driver <6>[ 3.798441] ehci-atmel: EHCI Atmel driver <6>[ 3.798620] tegra-ehci: Tegra EHCI driver <6>[ 3.798846] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.798865] ohci-pci: OHCI PCI platform driver <6>[ 3.798909] ohci-platform: OHCI generic platform driver <6>[ 3.799171] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.799357] ohci-st: OHCI STMicroelectronics driver <6>[ 3.799545] ohci-atmel: OHCI Atmel driver <6>[ 3.800771] usbcore: registered new interface driver usb-storage <6>[ 3.808946] i2c /dev entries driver <6>[ 3.828435] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.828442] sdhci: Copyright(c) Pierre Ossman <6>[ 3.831162] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.833104] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.838188] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.838221] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.838500] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.839291] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.840400] usbcore: registered new interface driver usbhid <6>[ 3.840407] usbhid: USB HID core driver <6>[ 3.846961] NET: Registered protocol family 10 <6>[ 3.848027] Segment Routing with IPv6 <6>[ 3.848105] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.848673] NET: Registered protocol family 17 <6>[ 3.848688] can: controller area network core <6>[ 3.848766] NET: Registered protocol family 29 <6>[ 3.848774] can: raw protocol <6>[ 3.848782] can: broadcast manager protocol <6>[ 3.848793] can: netlink gateway - max_hops=1 <5>[ 3.849176] Key type dns_resolver registered <6>[ 3.850946] ThumbEE CPU extension supported. <5>[ 3.850961] Registering SWP/SWPB emulation handler <6>[ 3.851390] printk: console [ttymxc1]: printing thread started <6>[ 3.851519] printk: console [ramoops-1]: printing thread started <5>[ 3.851548] Loading compiled-in X.509 certificates <6>[ 3.856894] pstore: Using crash dump compression: deflate <6>[ 3.870673] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.871268] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.882117] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.882269] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.884076] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.893655] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.897271] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.897300] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.916146] mmc2: new high speed SDHC card at address 0001 <6>[ 3.917006] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 3.927590] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.928363] hub 1-0:1.0: USB hub found <6>[ 3.928407] hub 1-0:1.0: 1 port detected <3>[ 3.930829] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 3.930841] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 3.930863] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 3.935581] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.935743] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.937429] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.942619] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.942765] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.944439] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.946848] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 3.952600] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.952758] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.954520] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.966326] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.966334] GPT:29296874 != 30560255 <4>[ 3.966340] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.966343] GPT:29296874 != 30560255 <4>[ 3.966347] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.966394] mmcblk2: p1 p2 p3 <4>[ 3.972391] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.972544] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.974231] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.071481] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.071531] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.071539] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.083452] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.217584] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.418664] hub 1-1:1.0: USB hub found <6>[ 4.418773] hub 1-1:1.0: 3 ports detected <4>[ 4.424513] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.424664] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.426393] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.158079] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.177644] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.207752] Sending DHCP requests ., OK <6>[ 6.247660] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 6.247688] IP-Config: Complete: <6>[ 6.247694] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.247720] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 6.247732] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.247746] nameserver0=192.168.201.1 <6>[ 6.255729] Freeing unused kernel memory: 2048K <6>[ 6.293019] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.438811] udevd[132]: starting version 3.2.9 <5>[ 6.439807] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.440054] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.440169] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.458914] udevd[132]: specified user 'tss' unknown <27>[ 6.459080] udevd[132]: specified group 'tss' unknown <30>[ 6.461846] udevd[133]: starting eudev-3.2.9 <6>[ 6.859330] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 6.861774] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 6.867515] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.867879] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.870747] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 6.882732] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.882912] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.884754] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 6.901118] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.901348] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.903600] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 6.928891] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.929081] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.064839] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.064970] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.065093] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.065222] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.129053] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.135192] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.135381] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.178465] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.188385] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.195629] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.195756] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.196145] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.196228] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.196243] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.196704] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 7.198455] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.198533] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.198610] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.198669] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.200422] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.206245] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.206427] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.210613] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.210689] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.210756] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.210814] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.429077] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.489878] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.550641] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.550665] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.550676] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 7.556465] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.602130] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.602338] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.627813] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.627918] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.627995] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.628058] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.637666] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.637902] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.638077] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.638233] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.639893] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.645926] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.646175] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.656932] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.657044] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.657151] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.657243] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.682293] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.690508] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.690715] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.697295] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.697408] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.697483] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.697540] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.741117] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.753723] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 7.813155] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.820776] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.821013] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.832625] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.832713] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.832806] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.832863] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.089912] caam algorithms registered in /proc/crypto <6>[ 8.091518] caam 2100000.crypto: registering rng-caam <4>[ 8.093429] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.100485] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.100674] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.105794] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.105872] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.105949] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done <6>[ 8.106005] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.107726] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: OK <5>[ 8.185089] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.274017] random: crng init done <5>[ 8.274035] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11090588/environment . /lava-11090588/environment / # /lava-11090588/bin/lava-test-runner /lava-11090588/0 /lava-11090588/bin/lava-test-runner /lava-11090588/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11090588/0/tests/0_dmesg + cat uuid + UUID=11090588_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.<8>[ 8.900319] sh <8>[ 8.950762] <8>[ 8.994888] + set +x / # <8>[ 9.037682] <8>[ 9.038932] # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11090588/environment / # . /lava-11090588/environment/lava-11090588/bin/lava-test-runner /lava-11090588/1 / # /lava-11090588/bin/lava-test-runner /lava-11090588/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11090588/1/tests/1_bootrr + cat uuid + UUID=11090588_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/he<8>[ 9.590785] lpers:/lava-11090588/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd 120000.hdmi panel-lvds0 /lava-11090588/1/../bin/lava-test-case <8>[ 10.671617] /lava-11090588/1/../bin/lava-test-case <8>[ 10.715680] /lava-11090588/1/../bin/lava-test-case <8>[ 10.737212] + set +x <8>[ 10.764785] / #