[Enter `^Ec?' for help] U-Boot 2015.01-rc3-00172-gd0a58bc (Dec 28 2014 - 23:49:42) for ODROID-XU3 CPU: Exynos5800@800MHz Board: Odroid XU3 based on EXYNOS5422 I2C: ready DRAM: 1.8 GiB trace: copying 000a7308 bytes of early data from 50000000 to aeff0000 trace: enabled MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 2  0 ODROID-XU3 # usb start usb start (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 1 Ethernet Device(s) found ODROID-XU3 # setenv autoload no setenv autoload no ODROID-XU3 # dhcp dhcp Waiting for Ethernet connection... done. BOOTP broadcast 1 EHCI timed out on TD - token=0x8008d80 BOOTP broadcast 2 DHCP client bound to address 192.168.201.15 (5012 ms) ODROID-XU3 # setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 ODROID-XU3 # tftp 0x42000000 12705531/tftp-deploy-ezdevrsr/kernel/zImage tftp 0x42000000 12705531/tftp-deploy-ezdevrsr/kernel/zImage Waiting for Ethernet connection... done. Using sms0 device TFTP from server 192.168.201.1; our IP address is 192.168.201.15 Filename '12705531/tftp-deploy-ezdevrsr/kernel/zImage'. Load address: 0x42000000 Loading: *T ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 443.4 KiB/s done Bytes transferred = 9720320 (945200 hex) ODROID-XU3 # tftp 0x43300000 12705531/tftp-deploy-ezdevrsr/ramdisk/ramdisk.cpio.gz.uboot tftp 0x43300000 12705531/tftp-deploy-ezdevrsr/ramdisk/ramdisk.cpio.gz.uboot Waiting for Ethernet connection... done. Using sms0 device TFTP from server 192.168.201.1; our IP address is 192.168.201.15 Filename '12705531/tftp-deploy-ezdevrsr/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x43300000 Loading: *EHCI timed out on TD - token=0x8008d80 T ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 655.3 KiB/s done Bytes transferred = 16077123 (f55143 hex) ODROID-XU3 # setenv initrd_size ${filesize} setenv initrd_size ${filesize} ODROID-XU3 # tftp 0x43000000 12705531/tftp-deploy-ezdevrsr/dtb/exynos5422-odroidxu3.dtb tftp 0x43000000 12705531/tftp-deploy-ezdevrsr/dtb/exynos5422-odroidxu3.dtb Waiting for Ethernet connection... done. Using sms0 device TFTP from server 192.168.201.1; our IP address is 192.168.201.15 Filename '12705531/tftp-deploy-ezdevrsr/dtb/exynos5422-odroidxu3.dtb'. Load address: 0x43000000 Loading: *EHCI timed out on TD - token=0x8008d80 T ##### 7.8 KiB/s done Bytes transferred = 65532 (fffc hex) ODROID-XU3 # setenv bootargs 'console=ttySAC2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' setenv bootargs 'console=ttySAC2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp' ODROID-XU3 # bootz 0x42000000 0x43300000 0x43000000 bootz 0x42000000 0x43300000 0x43000000 Kernel image @ 0x42000000 [ 0x000000 - 0x945200 ] ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16077059 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Ramdisk to 4f0aa000, end 4ffff103 ... OK Loading Device Tree to 4f097000, end 4f0a9ffb ... OK Starting kernel ...(fake run for tracing) Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 5.10.209-cip44-rt18 (KernelCI@build-j99558-arm-gcc-10-defconfig-8kbrf) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Feb 6 01:44:15 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Hardkernel Odroid XU3 [ 0.000000] earlycon: exynos4210 at MMIO 0x12c20000 (options '115200n8') [ 0.000000] printk: bootconsole [exynos4210] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xac000000 [ 0.000000] Samsung CPU ID: 0xe5422001 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000006fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000070000000-0x00000000afffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000afffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000afffffff] [ 0.000000] On node 0 totalpages: 458752 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 262144 pages, LIFO batch:63 [ 0.000000] Running under secure firmware. [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] pcpu-alloc: s33676 r8192 d23668 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 457216 [ 0.000000] Kernel command line: console=ttySAC2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=:::::eth0:dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1712548K/1835008K available (14336K kernel code, 2332K rwdata, 5364K rodata, 2048K init, 417K bss, 56924K reserved, 65536K cma-reserved, 983040K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=8. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <4>[ 0.008065] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57 <6>[ 0.022495] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.027380] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.038387] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.046616] Ignoring duplicate/late registration of read_current_timer delay <6>[ 0.057194] Console: colour dummy device 80x30 <6>[ 0.060476] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.071018] CPU: Testing write buffer coherency: ok <6>[ 0.076127] pid_max: default: 32768 minimum: 301 <6>[ 0.081134] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.088529] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.097757] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100 <6>[ 0.103380] Setting up static identity map for 0x40300000 - 0x403000ac <6>[ 0.109479] ARM CCI driver probed <6>[ 0.113214] Exynos MCPM support installed <6>[ 0.119561] rcu: Hierarchical SRCU implementation. <6>[ 0.126748] soc soc0: Exynos: CPU[EXYNOS5800] PRO_ID[0xe5422001] REV[0x1] Detected <6>[ 0.135405] EFI services will not be available. <6>[ 0.139333] smp: Bringing up secondary CPUs ... <6>[ 0.144505] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101 <6>[ 0.150555] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102 <6>[ 0.156455] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103 <6>[ 0.162333] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.167055] CPU4: Spectre v2: using ICIALLU workaround <6>[ 0.172427] CPU4: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.180277] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.184905] CPU5: Spectre v2: using ICIALLU workaround <6>[ 0.191519] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.196170] CPU6: Spectre v2: using ICIALLU workaround <6>[ 0.202789] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.207435] CPU7: Spectre v2: using ICIALLU workaround <6>[ 0.213017] smp: Brought up 1 node, 8 CPUs <6>[ 0.217168] SMP: Total of 8 processors activated (384.00 BogoMIPS). <6>[ 0.223638] CPU: All CPU(s) started in HYP mode. <6>[ 0.228506] CPU: Virtualization extensions available. <6>[ 0.234858] devtmpfs: initialized <6>[ 0.256604] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3 <6>[ 0.263331] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.273162] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) <6>[ 0.283700] pinctrl core: initialized pinctrl subsystem <6>[ 0.291247] DMI not present or invalid. <6>[ 0.294731] NET: Registered protocol family 16 <6>[ 0.301544] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.311094] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.313743] cpuidle: using governor menu <6>[ 0.322881] No ATAGs? <6>[ 0.325463] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.333443] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.342956] Serial: AMBA PL011 UART driver <6>[ 0.589091] EXYNOS5420 PMU initialized <6>[ 0.698361] iommu: Default domain type: Translated <6>[ 0.702439] vgaarb: loaded <5>[ 0.706032] SCSI subsystem initialized <7>[ 0.709130] libata version 3.00 loaded. <6>[ 0.713297] usbcore: registered new interface driver usbfs <6>[ 0.718785] usbcore: registered new interface driver hub <6>[ 0.724393] usbcore: registered new device driver usb <6>[ 0.731518] s3c-i2c 12c60000.i2c: slave address 0x00 <6>[ 0.735281] s3c-i2c 12c60000.i2c: bus frequency set to 65 KHz <6>[ 0.748290] s3c-i2c 12c60000.i2c: i2c-0: S3C I2C adapter <6>[ 0.752725] s3c-i2c 12c80000.i2c: slave address 0x00 <6>[ 0.757587] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz <6>[ 0.763811] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter <6>[ 0.770429] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.774326] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.783691] PTP clock support registered <6>[ 0.792443] clocksource: Switched to clocksource mct-frc <6>[ 1.754470] NET: Registered protocol family 2 <6>[ 1.757811] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.766311] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.773874] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.781849] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.789325] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.795874] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.802643] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.810041] NET: Registered protocol family 1 <6>[ 1.815143] RPC: Registered named UNIX socket transport module. <6>[ 1.820604] RPC: Registered udp transport module. <6>[ 1.825589] RPC: Registered tcp transport module. <6>[ 1.830488] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.837191] PCI: CLS 0 bytes, default 64 <6>[ 1.841968] Trying to unpack rootfs image as initramfs... <6>[ 2.919290] Freeing initrd memory: 15704K <6>[ 2.923850] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <6>[ 2.931547] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <5>[ 2.940845] Initialise system trusted keyrings <6>[ 2.944348] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 2.958417] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.963863] NFS: Registering the id_resolver key type <5>[ 2.968338] Key type id_resolver registered <5>[ 2.972766] Key type id_legacy registered <6>[ 2.977089] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.983937] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.991571] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.996641] Key type asymmetric registered <5>[ 3.000462] Asymmetric key parser 'x509' registered <6>[ 3.005656] bounce: pool size: 64 pages <6>[ 3.009675] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.017302] io scheduler mq-deadline registered <6>[ 3.022040] io scheduler kyber registered <4>[ 3.040194] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator <4>[ 3.047409] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator <4>[ 3.056706] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator <4>[ 3.064911] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator <6>[ 3.123532] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 <6>[ 3.129014] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 <6>[ 3.140049] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 <6>[ 3.145564] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 <6>[ 3.155272] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 <6>[ 3.161042] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 <6>[ 3.254638] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.265398] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 70, base_baud = 0) is a S3C6400/10 <6>[ 3.273764] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 71, base_baud = 0) is a S3C6<6>[ 3.282858] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 72, base_baud = 0) is a S3C6400/10 <6>[ 3.290661] printk: console [ttySAC2] enabled <6>[ 3.295183] printk: bootconsole [exynos4210] disabled <6>[ 3.290661] printk: console [ttySAC2] enabled <6>[ 3.295183] printk: bootconsole [exynos4210] disabled <6>[ 3.301129] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 73, base_baud = 0) is a S3C6400/10 <6>[ 3.302278] SuperH (H)SCI(F) driver initialized <6>[ 3.304376] msm_serial: driver initialized <6>[ 3.304743] STMicroelectronics ASC driver initialized <6>[ 3.307453] STM32 USART driver initialized <6>[ 3.309357] exynos-trng 10830600.rng: Exynos True Random Number Generator. <6>[ 3.331091] brd: module loaded <6>[ 3.341696] loop: module loaded <6>[ 3.364246] CAN device driver interface <6>[ 3.366064] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.368376] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.368380] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.368440] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.368445] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.377204] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.377245] usbcore: registered new interface driver pegasus <6>[ 3.377291] usbcore: registered new interface driver asix <6>[ 3.377325] usbcore: registered new interface driver ax88179_178a <6>[ 3.377360] usbcore: registered new interface driver cdc_ether <6>[ 3.377412] usbcore: registered new interface driver smsc75xx <6>[ 3.377460] usbcore: registered new interface driver smsc95xx <6>[ 3.377496] usbcore: registered new interface driver net1080 <6>[ 3.377531] usbcore: registered new interface driver cdc_subset <6>[ 3.377564] usbcore: registered new interface driver zaurus <6>[ 3.377634] usbcore: registered new interface driver cdc_ncm <6>[ 3.382969] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.382977] ehci-pci: EHCI PCI platform driver <6>[ 3.383014] ehci-platform: EHCI generic platform driver <6>[ 3.383403] ehci-orion: EHCI orion driver <6>[ 3.383734] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.384030] ehci-st: EHCI STMicroelectronics driver <6>[ 3.384325] ehci-exynos: EHCI Exynos driver <6>[ 3.384754] ehci-atmel: EHCI Atmel driver <6>[ 3.385042] tegra-ehci: Tegra EHCI driver <6>[ 3.385368] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.385387] ohci-pci: OHCI PCI platform driver <6>[ 3.385426] ohci-platform: OHCI generic platform driver <6>[ 3.385787] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.386084] ohci-st: OHCI STMicroelectronics driver <6>[ 3.386382] ohci-atmel: OHCI Atmel driver <6>[ 3.388059] usbcore: registered new interface driver usb-storage <6>[ 3.399029] i2c /dev entries driver <6>[ 3.426884] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV <6>[ 3.439155] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV <6>[ 3.453651] vdd_sd: Bringing 3300000uV into 2800000-2800000uV <6>[ 3.530025] exynos-tmu 10060000.tmu: More trip points than supported by this TMU. <6>[ 3.530036] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode. <6>[ 3.531241] exynos-tmu 10064000.tmu: More trip points than supported by this TMU. <6>[ 3.531250] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode. <6>[ 3.532518] exynos-tmu 10068000.tmu: More trip points than supported by this TMU. <6>[ 3.532526] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode. <6>[ 3.533731] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU. <6>[ 3.533739] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode. <6>[ 3.534953] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU. <6>[ 3.534960] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode. <6>[ 3.558118] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.558125] sdhci: Copyright(c) Pierre Ossman <6>[ 3.562334] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.565712] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. <6>[ 3.566124] dwmmc_exynos 12200000.mmc: Using internal DMA controller. <6>[ 3.566181] dwmmc_exynos 12200000.mmc: Version ID is 250a <6>[ 3.566380] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. <6>[ 3.566402] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.566454] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 94,64 bit host data width,64 deep fifo <6>[ 3.566595] dwmmc_exynos 12220000.mmc: Using internal DMA controller. <6>[ 3.566648] dwmmc_exynos 12220000.mmc: Version ID is 250a <6>[ 3.566911] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 95,64 bit host data width,64 deep fifo <6>[ 3.569036] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq <6>[ 3.575116] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.576502] usbcore: registered new interface driver usbhid <6>[ 3.576507] usbhid: USB HID core driver <6>[ 3.585677] NET: Registered protocol family 10 <6>[ 3.587007] Segment Routing with IPv6 <6>[ 3.587080] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.587735] NET: Registered protocol family 17 <6>[ 3.587751] can: controller area network core <6>[ 3.587818] NET: Registered protocol family 29 <6>[ 3.587826] can: raw protocol <6>[ 3.587834] can: broadcast manager protocol <6>[ 3.587846] can: netlink gateway - max_hops=1 <5>[ 3.588332] Key type dns_resolver registered <6>[ 3.589146] ThumbEE CPU extension supported. <5>[ 3.589160] Registering SWP/SWPB emulation handler <6>[ 3.590067] printk: console [ttySAC2]: printing thread started <5>[ 3.590098] Loading compiled-in X.509 certificates <6>[ 3.594394] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330 <6>[ 3.594406] dma-pl330 3880000.adma: DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6 <6>[ 3.595961] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) <6>[ 3.612569] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) <4>[ 3.635518] dma-pl330 3880000.adma: PM domain MAU will not be powered off <6>[ 3.636226] exynos-asv 10000000.chipid: cpu0 opp0, freq: 1500 missing <6>[ 3.636266] exynos-asv 10000000.chipid: cpu4 opp0, freq: 2100 missing <6>[ 3.640179] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller <6>[ 3.640194] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 1 <6>[ 3.640395] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 <6>[ 3.640468] xhci-hcd xhci-hcd.6.auto: irq 170, io mem 0x12000000 <6>[ 3.640636] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller <6>[ 3.640644] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 2 <6>[ 3.640651] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.641151] hub 1-0:1.0: USB hub found <6>[ 3.641174] hub 1-0:1.0: 1 port detected <6>[ 3.641428] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.641827] hub 2-0:1.0: USB hub found <6>[ 3.641849] hub 2-0:1.0: 1 port detected <6>[ 3.645720] dwc3 12400000.dwc3: changing max_speed on rev 5533200a <6>[ 3.654640] input: gpio_keys as /devices/platform/gpio_keys/input/input0 <6>[ 3.921024] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 3.921123] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0) <6>[ 3.922237] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 3.923631] mmc_host mmc0: Bus speed (slot 0) = 400000000Hz (slot req 200000000Hz, actual 200000000HZ div = 1) <6>[ 3.924038] mmc0: new HS400 MMC card at address 0001 <6>[ 3.926534] mmcblk0: mmc0:0001 SDW32G 29.1 GiB <6>[ 3.928106] mmcblk0boot0: mmc0:0001 SDW32G partition 1 4.00 MiB <6>[ 3.929683] mmcblk0boot1: mmc0:0001 SDW32G partition 2 4.00 MiB <6>[ 3.930129] mmcblk0rpmb: mmc0:0001 SDW32G partition 3 4.00 MiB, chardev (235:0) <6>[ 3.939993] mmcblk0: p1 p2 <6>[ 16.171275] Freeing unused kernel memory: 2048K <6>[ 16.173307] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.331923] udevd[160]: starting version 3.2.9 <5>[ 16.332752] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.332983] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.333063] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 16.338337] udevd[160]: specified user 'tss' unknown <27>[ 16.338421] udevd[160]: specified group 'tss' unknown <30>[ 16.340500] udevd[161]: starting eudev-3.2.9 <6>[ 16.679583] s5p-secss 10830000.sss: s5p-sss driver registered <6>[ 16.719375] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp <6>[ 16.719630] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp <6>[ 16.719807] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp <6>[ 16.719988] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp <6>[ 16.736409] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0_0) <6>[ 16.756781] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled <6>[ 16.756988] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0_1) <6>[ 16.767069] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1_0) <6>[ 16.767551] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1_1) <6>[ 16.773287] mc: Linux media interface: v0.10 <6>[ 16.785222] videodev: Linux video capture interface: v2.00 <6>[ 16.794796] s5p-jpeg 11f50000.jpeg: Adding to iommu group 0 <6>[ 16.794964] panfrost 11800000.gpu: clock rate = 400000000 <6>[ 16.795674] s5p-jpeg 11f50000.jpeg: encoder device registered as /dev/video0 <6>[ 16.795832] s5p-jpeg 11f50000.jpeg: decoder device registered as /dev/video1 <6>[ 16.795839] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec <6>[ 16.796141] s5p-jpeg 11f60000.jpeg: Adding to iommu group 1 <6>[ 16.807667] s5p-jpeg 11f60000.jpeg: encoder device registered as /dev/video2 <6>[ 16.808206] s5p-mfc 11000000.codec: Adding to iommu group 2 <6>[ 16.808467] s5p-jpeg 11f60000.jpeg: decoder device registered as /dev/video3 <6>[ 16.808478] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec <4>[ 16.812682] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator <6>[ 16.819503] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0 <6>[ 16.823144] exynos-ehci 12110000.usb: EHCI Host Controller <6>[ 16.823176] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 3 <6>[ 16.824381] ohci-exynos: OHCI Exynos driver <6>[ 16.824907] exynos-ohci 12120000.usb: USB Host Controller <6>[ 16.824928] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 4 <6>[ 16.827564] s5p-mfc 11000000.codec: preallocated 8 MiB buffer for the firmware and context buffers <4>[ 16.828276] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v8.fw failed with error -2 <3>[ 16.828287] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel <6>[ 16.828604] s5p-mfc 11000000.codec: decoder registered as /dev/video4 <6>[ 16.834364] panfrost 11800000.gpu: mali-t620 id 0x620 major 0x0 minor 0x1 status 0x0 <6>[ 16.834374] panfrost 11800000.gpu: features: 00000000,10206400, issues: 00000000,21eee400 <6>[ 16.834380] panfrost 11800000.gpu: Features: L2:0x07110206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xf JS:0x7 <6>[ 16.834387] panfrost 11800000.gpu: shader_present=0x3f l2_present=0x11 <6>[ 16.842533] s5p-mfc 11000000.codec: encoder registered as /dev/video5 <6>[ 16.910347] [drm] Initialized panfrost 1.1.0 20180908 for 11800000.gpu on minor 0 <6>[ 16.938516] exynos-gsc 13e00000.video-scaler: Adding to iommu group 3 <6>[ 16.941456] exynos-gsc 13e10000.video-scaler: Adding to iommu group 4 <6>[ 16.950198] exynos-mixer 14450000.mixer: Adding to iommu group 5 <3>[ 16.956119] OF: graph: no port node found in /soc/hdmi@14530000 <6>[ 16.975898] s5m-rtc s2mps14-rtc: registered as rtc0 <6>[ 16.977804] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01T00:01:46 UTC (946684906) <6>[ 16.980052] ina2xx 0-0040: power monitor ina231 (Rshunt = 10000 uOhm) <6>[ 17.001831] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations <6>[ 17.001905] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm]) <6>[ 17.001970] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops [exynosdrm]) <6>[ 17.002309] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes <6>[ 17.002673] exynos-drm exynos-drm: [drm] Cannot find any crtc or sizes <6>[ 17.003000] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1 <4>[ 17.004411] s2mps11-clk s2mps11-clk: DMA mask not set <6>[ 17.023133] exynos-bus: new bus device registered: soc:bus_wcore ( 88700 KHz ~ 532000 KHz) <6>[ 17.023347] ina2xx 0-0041: power monitor ina231 (Rshunt = 10000 uOhm) <6>[ 17.025019] ina2xx 0-0044: power monitor ina231 (Rshunt = 10000 uOhm) <6>[ 17.026592] ina2xx 0-0045: power monitor ina231 (Rshunt = 10000 uOhm) <6>[ 17.030618] exynos-bus: new bus device registered: soc:bus_noc ( 66600 KHz ~ 111000 KHz) <6>[ 17.031169] exynos-bus: new bus device registered: soc:bus_fsys_apb (111000 KHz ~ 222000 KHz) <6>[ 17.031804] exynos-bus: new bus device registered: soc:bus_fsys2 ( 75000 KHz ~ 200000 KHz) <6>[ 17.032683] exynos-bus: new bus device registered: soc:bus_mfc ( 83250 KHz ~ 333000 KHz) <6>[ 17.033374] exynos-bus: new bus device registered: soc:bus_gen ( 88700 KHz ~ 266000 KHz) <6>[ 17.033736] exynos-bus: new bus device registered: soc:bus_peri ( 66600 KHz ~ 66600 KHz) <6>[ 17.034395] exynos-bus: new bus device registered: soc:bus_g2d ( 83250 KHz ~ 333000 KHz) <6>[ 17.035053] exynos-bus: new bus device registered: soc:bus_g2d_acp ( 66500 KHz ~ 266000 KHz) <6>[ 17.035657] exynos-bus: new bus device registered: soc:bus_jpeg ( 75000 KHz ~ 300000 KHz) <6>[ 17.036236] exynos-bus: new bus device registered: soc:bus_jpeg_apb ( 83250 KHz ~ 166500 KHz) <6>[ 17.036661] exynos-bus: new bus device registered: soc:bus_disp1_fimd (120000 KHz ~ 200000 KHz) <6>[ 17.037148] exynos-bus: new bus device registered: soc:bus_disp1 (120000 KHz ~ 300000 KHz) <6>[ 17.037650] exynos-bus: new bus device registered: soc:bus_gscl_scaler (150000 KHz ~ 300000 KHz) <6>[ 17.038291] exynos-bus: new bus device registered: soc:bus_mscl ( 84000 KHz ~ 666000 KHz) <4>[ 17.066424] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s <4>[ 17.198923] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v8.fw failed with error -2 <3>[ 17.198946] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel <4>[ 17.216248] s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v8.fw failed with error -2 <3>[ 17.216268] s5p_mfc_load_firmware:69: Firmware is not present in the /lib/firmware directory nor compiled in kernel <6>[ 17.295208] exynos-ehci 12110000.usb: irq 92, io mem 0x12110000 <6>[ 17.295234] exynos-ohci 12120000.usb: irq 92, io mem 0x12120000 <6>[ 17.327878] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 <6>[ 17.330289] hub 3-0:1.0: USB hub found <6>[ 17.330425] hub 3-0:1.0: 3 ports detected <6>[ 17.368696] hub 4-0:1.0: USB hub found <6>[ 17.368808] hub 4-0:1.0: 3 ports detected <6>[ 17.393167] max98090 5-0010: MAX98090 REVID=0x43 <6>[ 17.395205] max98090 5-0010: use default 2.8v micbias done <6>[ 17.426607] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling <6>[ 17.428018] s3c-rtc 101e0000.rtc: registered as rtc1 Saving random seed: <5>[ 17.471046] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: <5>[ 17.591889] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # <6>[ 17.632545] usb 3-1: new high-speed USB device number 2 using exynos-ehci / # # # / # export SHELL=/bin/sh <6>[ 17.839100] hub 3-1:1.0: USB hub found <6>[ 17.839581] hub 3-1:1.0: 5 ports detected export SHELL=/bin/sh / # . /lava-12705531/environment . /lava-12705531/environment / # /lava-12705531/bin/lava-test-runner /lava-12705531/0 /lava-12705531/bin/lava-test-runner /lava-12705531/0 <6>[ 18.162704] usb 3-1.1: new high-speed USB device number 3 using exynos-ehci + export 'TESTRUN_ID=0_dmesg' + cd /lava-12705531/0/tests/0_dmesg + cat uuid + UUID=12705531_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.292471] <8>[ 18.338996] <6>[ 18.346044] smsc95xx v2.0.0 <8>[ 18.374359] + set +x <8>[ 18.417913] <8>[ 18.420759] / # # export SHELL=/bin/sh # / # <6>[ 18.559785] SMSC LAN8700 usb-003:003:01: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=usb-003:003:01, irq=POLL) <6>[ 18.563398] smsc95xx 3-1.1:1.0 eth0: register 'smsc95xx' at usb-12110000.usb-1.1, smsc95xx USB 2.0 Ethernet, 46:6c:a2:89:64:e7 export SHELL=/bin/sh. /lava-12705531/environment / # . /lava-12705531/environment/lava-12705531/bin/lava-test-runner /lava-12705531/1 / # /lava-12705531/bin/lava-test-runner /lava-12705531/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12705531/1/tests/1_bootrr + cat uuid + UUID=12705531_1.5.2.4.5 + set +x + export 'PATH=/opt/bo<8>[ o tr1r8/.978025] libexec/bootrr/helpers:/lava-12705531/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-12705531/1/../bin/lava-test-case <8>[ 19.048976] /lava-12705531/1/../bin/lava-test-case <8>[ 19.098570] /lava-12705531/1/../bin/lava-test-case <8>[ 19.125822] + set +x �