[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12705445/tftp-deploy-oga2nobx/kernel/zImage tftp 0x10000000 12705445/tftp-deploy-oga2nobx/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '12705445/tftp-deploy-oga2nobx/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 6 MiB/s done Bytes transferred = 9720320 (945200 hex) => tftp 0x14000000 12705445/tftp-deploy-oga2nobx/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12705445/tftp-deploy-oga2nobx/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '12705445/tftp-deploy-oga2nobx/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 14.1 MiB/s done Bytes transferred = 16081164 (f5610c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12705445/tftp-deploy-oga2nobx/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12705445/tftp-deploy-oga2nobx/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '12705445/tftp-deploy-oga2nobx/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.5 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x945200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16081100 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.209-cip44-rt18 (KernelCI@build-j99560-arm-gcc-10-multi-v7-defconfig-d9q9l) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Feb 6 01:44:18 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] pcpu-alloc: s33676 r8192 d23668 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932628K/1048576K available (14336K kernel code, 2332K rwdata, 5364K rodata, 2048K init, 417K bss, 50412K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008439] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022201] Console: colour dummy device 80x30 <6>[ 0.024092] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034504] CPU: Testing write buffer coherency: ok <6>[ 0.039634] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044933] pid_max: default: 32768 minimum: 301 <6>[ 0.049958] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057395] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066274] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072011] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079693] rcu: Hierarchical SRCU implementation. <6>[ 0.086656] EFI services will not be available. <6>[ 0.088897] smp: Bringing up secondary CPUs ... <6>[ 0.094199] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099296] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105532] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110518] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116732] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121742] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127172] smp: Brought up 1 node, 4 CPUs <6>[ 0.131398] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137855] CPU: All CPU(s) started in SVC mode. <6>[ 0.143272] devtmpfs: initialized <6>[ 0.153736] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159085] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168950] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179162] pinctrl core: initialized pinctrl subsystem <6>[ 0.183653] DMI not present or invalid. <6>[ 0.186753] NET: Registered protocol family 16 <6>[ 0.194104] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200764] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200953] cpuidle: using governor menu <6>[ 0.209026] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.411357] vdd1p1: supplied by regulator-dummy <6>[ 0.421445] vdd3p0: supplied by regulator-dummy <6>[ 0.431402] vdd2p5: supplied by regulator-dummy <6>[ 0.441452] vddarm: supplied by regulator-dummy <6>[ 0.451624] vddpu: supplied by regulator-dummy <6>[ 0.461369] vddsoc: supplied by regulator-dummy <6>[ 0.836090] No ATAGs? <6>[ 0.836274] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.844033] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.854286] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.864675] Serial: AMBA PL011 UART driver <6>[ 0.868420] printk: console [ramoops-1] enabled <6>[ 0.871172] pstore: Registered ramoops as persistent store backend <6>[ 0.877428] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.915313] iommu: Default domain type: Translated <6>[ 0.918126] vgaarb: loaded <5>[ 0.921440] SCSI subsystem initialized <7>[ 0.924894] libata version 3.00 loaded. <6>[ 0.928938] usbcore: registered new interface driver usbfs <6>[ 0.934437] usbcore: registered new interface driver hub <6>[ 0.940018] usbcore: registered new device driver usb <6>[ 0.946865] i2c i2c-0: IMX I2C adapter registered <6>[ 0.951571] i2c i2c-1: IMX I2C adapter registered <6>[ 0.956034] i2c i2c-2: IMX I2C adapter registered <6>[ 0.961502] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.965368] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.974805] PTP clock support registered <6>[ 0.982560] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.094357] NET: Registered protocol family 2 <6>[ 2.096548] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.105184] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.112427] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.120514] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.127962] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.134634] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.141319] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.148801] NET: Registered protocol family 1 <6>[ 2.153835] RPC: Registered named UNIX socket transport module. <6>[ 2.159379] RPC: Registered udp transport module. <6>[ 2.164374] RPC: Registered tcp transport module. <6>[ 2.169296] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.176023] PCI: CLS 0 bytes, default 64 <6>[ 2.180653] Trying to unpack rootfs image as initramfs... <6>[ 3.546966] Freeing initrd memory: 15708K <4>[ 3.548820] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.556346] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.566058] Initialise system trusted keyrings <6>[ 3.569160] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.581311] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.585320] NFS: Registering the id_resolver key type <5>[ 3.589891] Key type id_resolver registered <5>[ 3.594327] Key type id_legacy registered <6>[ 3.598662] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.605540] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.613234] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.618277] Key type asymmetric registered <5>[ 3.622140] Asymmetric key parser 'x509' registered <6>[ 3.627340] bounce: pool size: 64 pages <6>[ 3.631393] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.639036] io scheduler mq-deadline registered <6>[ 3.643817] io scheduler kyber registered <6>[ 3.688082] mxs-dma 110000.dma-controller: initialized <4>[ 3.695420] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.703232] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.760435] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.768653] SuperH (H)SCI(F) driver initialized <6>[ 3.771597] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.780482] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.788437] printk: console [ttymxc1] enabled <6>[ 3.792955] printk: bootconsole [ec_imx21] disabled <6>[ 3.788437] printk: console [ttymxc1] enabled <6>[ 3.792955] printk: bootconsole [ec_imx21] disabled <6>[ 3.799659] msm_serial: driver initialized <6>[ 3.799917] STMicroelectronics ASC driver initialized <6>[ 3.801868] STM32 USART driver initialized <4>[ 3.812437] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.812622] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.813250] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.822046] brd: module loaded <6>[ 3.829550] loop: module loaded <6>[ 3.833601] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.833616] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.833626] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.833635] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.833709] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.833854] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.833943] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.836774] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.836802] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.836820] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.838321] scsi host0: ahci-imx <6>[ 3.838692] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.851355] CAN device driver interface <6>[ 3.852754] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.856353] pps pps0: new PPS source ptp0 <6>[ 3.889541] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.891058] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.891064] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.891125] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.891131] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.897447] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.897501] usbcore: registered new interface driver pegasus <6>[ 3.897543] usbcore: registered new interface driver asix <6>[ 3.897577] usbcore: registered new interface driver ax88179_178a <6>[ 3.897612] usbcore: registered new interface driver cdc_ether <6>[ 3.897655] usbcore: registered new interface driver smsc75xx <6>[ 3.897706] usbcore: registered new interface driver smsc95xx <6>[ 3.897749] usbcore: registered new interface driver net1080 <6>[ 3.897785] usbcore: registered new interface driver cdc_subset <6>[ 3.897817] usbcore: registered new interface driver zaurus <6>[ 3.897887] usbcore: registered new interface driver cdc_ncm <6>[ 3.901546] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.901553] ehci-pci: EHCI PCI platform driver <6>[ 3.901592] ehci-platform: EHCI generic platform driver <6>[ 3.901887] ehci-orion: EHCI orion driver <6>[ 3.902113] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.902299] ehci-st: EHCI STMicroelectronics driver <6>[ 3.902484] ehci-exynos: EHCI Exynos driver <6>[ 3.902712] ehci-atmel: EHCI Atmel driver <6>[ 3.902907] tegra-ehci: Tegra EHCI driver <6>[ 3.903130] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.903151] ohci-pci: OHCI PCI platform driver <6>[ 3.903195] ohci-platform: OHCI generic platform driver <6>[ 3.903467] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.903671] ohci-st: OHCI STMicroelectronics driver <6>[ 3.903862] ohci-atmel: OHCI Atmel driver <6>[ 3.905153] usbcore: registered new interface driver usb-storage <6>[ 3.913603] i2c /dev entries driver <6>[ 3.933942] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.933949] sdhci: Copyright(c) Pierre Ossman <6>[ 3.936785] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.938798] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.940084] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.940126] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.941347] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.944151] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.945188] usbcore: registered new interface driver usbhid <6>[ 3.945196] usbhid: USB HID core driver <6>[ 3.951920] NET: Registered protocol family 10 <6>[ 3.953008] Segment Routing with IPv6 <6>[ 3.953089] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.953646] NET: Registered protocol family 17 <6>[ 3.953662] can: controller area network core <6>[ 3.953742] NET: Registered protocol family 29 <6>[ 3.953750] can: raw protocol <6>[ 3.953757] can: broadcast manager protocol <6>[ 3.953767] can: netlink gateway - max_hops=1 <5>[ 3.954159] Key type dns_resolver registered <6>[ 3.956223] ThumbEE CPU extension supported. <5>[ 3.956239] Registering SWP/SWPB emulation handler <6>[ 3.957057] printk: console [ttymxc1]: printing thread started <6>[ 3.957255] printk: console [ramoops-1]: printing thread started <5>[ 3.957281] Loading compiled-in X.509 certificates <6>[ 3.962374] pstore: Using crash dump compression: deflate <6>[ 3.973216] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.973657] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.983573] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.983719] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.985168] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.993714] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.997215] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.997240] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.022561] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.023158] hub 1-0:1.0: USB hub found <6>[ 4.023193] hub 1-0:1.0: 1 port detected <6>[ 4.025212] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.029569] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.029697] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.031091] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.035348] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.035470] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.036868] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.038809] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.044326] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.044459] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.045883] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.155556] mmc2: new high speed SDHC card at address 0001 <6>[ 4.156310] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 4.174069] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.174126] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.174133] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.186497] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <4>[ 4.266814] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.266820] GPT:7812499 != 30560255 <4>[ 4.266826] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.266829] GPT:7812499 != 30560255 <4>[ 4.266832] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.266869] mmcblk2: p1 p2 p3 <4>[ 4.272083] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.272222] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.273731] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.312540] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.538005] hub 1-1:1.0: USB hub found <6>[ 4.545722] hub 1-1:1.0: 3 ports detected <4>[ 4.593381] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.593507] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.594952] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.283081] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.312663] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.342679] Sending DHCP requests ., OK <6>[ 7.382626] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 7.382652] IP-Config: Complete: <6>[ 7.382658] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.382682] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 7.382695] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.382710] nameserver0=192.168.201.1 <6>[ 7.391222] Freeing unused kernel memory: 2048K <6>[ 7.445273] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.563176] udevd[140]: starting version 3.2.9 <5>[ 7.564040] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.564288] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.564382] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.571370] udevd[140]: specified user 'tss' unknown <27>[ 7.571490] udevd[140]: specified group 'tss' unknown <30>[ 7.574579] udevd[141]: starting eudev-3.2.9 <6>[ 7.879201] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.881170] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.887860] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.888072] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.890512] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.903697] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.903861] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.905693] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.949709] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.949859] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.951379] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.091849] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.092047] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.095027] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.114689] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.175493] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.217022] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.217176] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.219037] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.236255] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.236273] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.236282] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.244417] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.247034] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.248923] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.281065] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.287383] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.287817] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.287908] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.322779] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.322863] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.322876] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.323291] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 8.326831] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.326989] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.328542] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.362913] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.363023] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.363131] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.363247] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.367297] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.367450] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.369073] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.386203] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.386266] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.386328] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.386379] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.576011] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.576245] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.576981] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.577148] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.577336] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.577478] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.578392] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.587090] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.587158] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.587215] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.587259] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.588552] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.591198] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.591420] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.593481] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.640298] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.653709] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.653781] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.653843] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.653890] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.657455] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.657622] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.950737] caam algorithms registered in /proc/crypto <6>[ 8.952082] caam 2100000.crypto: registering rng-caam <4>[ 8.965151] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.982965] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.983092] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) done <6>[ 8.983224] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.983356] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.986790] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.986954] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.988653] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 9.058917] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) OK<6>[ 9.058983] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.059044] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.059090] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <5>[ 9.068102] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL <5>[ 9.134516] random: crng init done <5>[ 9.134528] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12705445/environment . /lava-12705445/environment / # /lava-12705445/bin/lava-test-runner /lava-12705445/0 /lava-12705445/bin/lava-test-runner /lava-12705445/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12705445/0/tests/0_dmesg + cat uuid + UUID=12705445_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.784003] <8>[ 9.832717] <8>[ 9.865830] + set +x <8>[ 9.899092] / # <8>[ 9.900348] # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12705445/environment / # . /lava-12705445/environment/lava-12705445/bin/lava-test-runner /lava-12705445/1 / # /lava-12705445/bin/lava-test-runner /lava-12705445/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12705445/1/tests/1_bootrr + cat uuid + UUID=12705445_1.5.2.4.5 + set +x + export 'PAT<8>[ 10.417959] H=/opt/bootrr/libexec/bootrr/helpers:/lava-12705445/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 backlight-lcd 120000.hdmi /lava-12705445/1/../bin/lava-test-case <8>[ 11.482309] /lava-12705445/1/../bin/lava-test-case /lava-12705445/1/../bin/lava-test-case <8>[ 11.522717] <8>[ 11.540166] + set +x / # <8>[ 11.559319]