[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13433227/tftp-deploy-0rfibe_0/kernel/zImage tftp 0x10000000 13433227/tftp-deploy-0rfibe_0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '13433227/tftp-deploy-0rfibe_0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 5.8 MiB/s done Bytes transferred = 9720320 (945200 hex) => tftp 0x14000000 13433227/tftp-deploy-0rfibe_0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13433227/tftp-deploy-0rfibe_0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '13433227/tftp-deploy-0rfibe_0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.8 MiB/s done Bytes transferred = 16081947 (f5641b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13433227/tftp-deploy-0rfibe_0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13433227/tftp-deploy-0rfibe_0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '13433227/tftp-deploy-0rfibe_0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.8 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x945200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16081883 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.214-cip46-rt19 (KernelCI@build-j172096-arm-gcc-10-multi-v7-defconfig-nkhvp) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Apr 19 23:43:16 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33676 r8192 d23668 u65536 [ 0.000000] pcpu-alloc: s33676 r8192 d23668 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932628K/1048576K available (14336K kernel code, 2332K rwdata, 5368K rodata, 2048K init, 417K bss, 50412K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022191] Console: colour dummy device 80x30 <6>[ 0.024085] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034493] CPU: Testing write buffer coherency: ok <6>[ 0.039625] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044924] pid_max: default: 32768 minimum: 301 <6>[ 0.049946] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057386] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066261] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072004] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079715] rcu: Hierarchical SRCU implementation. <6>[ 0.086687] EFI services will not be available. <6>[ 0.088926] smp: Bringing up secondary CPUs ... <6>[ 0.094228] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099326] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105562] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110549] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116765] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121772] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127201] smp: Brought up 1 node, 4 CPUs <6>[ 0.131428] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137887] CPU: All CPU(s) started in SVC mode. <6>[ 0.143298] devtmpfs: initialized <6>[ 0.153755] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159103] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168966] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179183] pinctrl core: initialized pinctrl subsystem <6>[ 0.183648] DMI not present or invalid. <6>[ 0.186761] NET: Registered protocol family 16 <6>[ 0.194149] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200795] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200982] cpuidle: using governor menu <6>[ 0.209064] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.386573] vdd1p1: supplied by regulator-dummy <6>[ 0.395646] vdd3p0: supplied by regulator-dummy <6>[ 0.404594] vdd2p5: supplied by regulator-dummy <6>[ 0.413587] vddarm: supplied by regulator-dummy <6>[ 0.422741] vddpu: supplied by regulator-dummy <6>[ 0.431495] vddsoc: supplied by regulator-dummy <6>[ 0.757779] No ATAGs? <6>[ 0.757962] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.765742] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.775918] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.786115] Serial: AMBA PL011 UART driver <6>[ 0.789781] printk: console [ramoops-1] enabled <6>[ 0.792610] pstore: Registered ramoops as persistent store backend <6>[ 0.798873] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.836575] iommu: Default domain type: Translated <6>[ 0.839300] vgaarb: loaded <5>[ 0.842692] SCSI subsystem initialized <7>[ 0.846169] libata version 3.00 loaded. <6>[ 0.850163] usbcore: registered new interface driver usbfs <6>[ 0.855743] usbcore: registered new interface driver hub <6>[ 0.861263] usbcore: registered new device driver usb <6>[ 0.868100] i2c i2c-0: IMX I2C adapter registered <6>[ 0.872826] i2c i2c-1: IMX I2C adapter registered <6>[ 0.877308] i2c i2c-2: IMX I2C adapter registered <6>[ 0.882739] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.886650] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.896060] PTP clock support registered <6>[ 0.903773] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.015568] NET: Registered protocol family 2 <6>[ 2.017773] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.026389] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.033637] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.041714] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.049170] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.055848] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.062527] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.070010] NET: Registered protocol family 1 <6>[ 2.075051] RPC: Registered named UNIX socket transport module. <6>[ 2.080589] RPC: Registered udp transport module. <6>[ 2.085582] RPC: Registered tcp transport module. <6>[ 2.090507] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.097231] PCI: CLS 0 bytes, default 64 <6>[ 2.101861] Trying to unpack rootfs image as initramfs... <6>[ 3.464730] Freeing initrd memory: 15708K <4>[ 3.466626] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.474025] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.483837] Initialise system trusted keyrings <6>[ 3.486932] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.499106] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.503075] NFS: Registering the id_resolver key type <5>[ 3.507791] Key type id_resolver registered <5>[ 3.512093] Key type id_legacy registered <6>[ 3.516474] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.523317] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.531020] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.536111] Key type asymmetric registered <5>[ 3.539935] Asymmetric key parser 'x509' registered <6>[ 3.545135] bounce: pool size: 64 pages <6>[ 3.549188] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.556832] io scheduler mq-deadline registered <6>[ 3.561598] io scheduler kyber registered <6>[ 3.605155] mxs-dma 110000.dma-controller: initialized <4>[ 3.623696] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.631542] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.670156] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.678322] SuperH (H)SCI(F) driver initialized <6>[ 3.681255] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.690160] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.698104] printk: console [ttymxc1] enabled <6>[ 3.702610] printk: bootconsole [ec_imx21] disabled <6>[ 3.698104] printk: console [ttymxc1] enabled <6>[ 3.702610] printk: bootconsole [ec_imx21] disabled <6>[ 3.709296] msm_serial: driver initialized <6>[ 3.709557] STMicroelectronics ASC driver initialized <6>[ 3.711515] STM32 USART driver initialized <4>[ 3.721943] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.722089] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.722443] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.731213] brd: module loaded <6>[ 3.738610] loop: module loaded <6>[ 3.742534] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.742549] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.742559] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.742569] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.742644] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.742796] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.742855] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.745692] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.745720] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.745736] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.747249] scsi host0: ahci-imx <6>[ 3.747613] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.759951] CAN device driver interface <6>[ 3.761261] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.764060] pps pps0: new PPS source ptp0 <6>[ 3.797431] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.798927] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.798933] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.798994] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.798999] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.805245] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.805292] usbcore: registered new interface driver pegasus <6>[ 3.805343] usbcore: registered new interface driver asix <6>[ 3.805380] usbcore: registered new interface driver ax88179_178a <6>[ 3.805413] usbcore: registered new interface driver cdc_ether <6>[ 3.805458] usbcore: registered new interface driver smsc75xx <6>[ 3.805502] usbcore: registered new interface driver smsc95xx <6>[ 3.805536] usbcore: registered new interface driver net1080 <6>[ 3.805576] usbcore: registered new interface driver cdc_subset <6>[ 3.805608] usbcore: registered new interface driver zaurus <6>[ 3.805680] usbcore: registered new interface driver cdc_ncm <6>[ 3.809272] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.809279] ehci-pci: EHCI PCI platform driver <6>[ 3.809326] ehci-platform: EHCI generic platform driver <6>[ 3.809613] ehci-orion: EHCI orion driver <6>[ 3.809837] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.810024] ehci-st: EHCI STMicroelectronics driver <6>[ 3.810210] ehci-exynos: EHCI Exynos driver <6>[ 3.810387] ehci-atmel: EHCI Atmel driver <6>[ 3.810564] tegra-ehci: Tegra EHCI driver <6>[ 3.810778] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.810798] ohci-pci: OHCI PCI platform driver <6>[ 3.810842] ohci-platform: OHCI generic platform driver <6>[ 3.811102] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.811294] ohci-st: OHCI STMicroelectronics driver <6>[ 3.811490] ohci-atmel: OHCI Atmel driver <6>[ 3.812729] usbcore: registered new interface driver usb-storage <6>[ 3.821040] i2c /dev entries driver <6>[ 3.840791] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.840799] sdhci: Copyright(c) Pierre Ossman <6>[ 3.843560] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.845581] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.846862] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.846905] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.848109] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.850764] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.851762] usbcore: registered new interface driver usbhid <6>[ 3.851769] usbhid: USB HID core driver <6>[ 3.858492] NET: Registered protocol family 10 <6>[ 3.859560] Segment Routing with IPv6 <6>[ 3.859641] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.860205] NET: Registered protocol family 17 <6>[ 3.860221] can: controller area network core <6>[ 3.860300] NET: Registered protocol family 29 <6>[ 3.860309] can: raw protocol <6>[ 3.860317] can: broadcast manager protocol <6>[ 3.860327] can: netlink gateway - max_hops=1 <5>[ 3.860719] Key type dns_resolver registered <6>[ 3.862791] ThumbEE CPU extension supported. <5>[ 3.862806] Registering SWP/SWPB emulation handler <6>[ 3.863669] printk: console [ttymxc1]: printing thread started <6>[ 3.863892] printk: console [ramoops-1]: printing thread started <5>[ 3.863918] Loading compiled-in X.509 certificates <6>[ 3.868949] pstore: Using crash dump compression: deflate <6>[ 3.888536] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.888905] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <4>[ 3.890173] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.890306] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.891785] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.900232] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.903788] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.903819] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.933757] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.934371] hub 1-0:1.0: USB hub found <6>[ 3.934405] hub 1-0:1.0: 1 port detected <6>[ 3.936499] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.940743] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.940879] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.942250] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.946553] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.946676] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.948025] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.949899] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 3.955196] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.955330] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.956727] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.095395] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.095441] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.095448] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.111788] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.135569] mmc2: new high speed SDHC card at address 0001 <6>[ 4.141801] mmcblk2: mmc2:0001 SD 14.6 GiB (ro) <4>[ 4.197139] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.197147] GPT:7812499 != 30560255 <4>[ 4.197152] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.197155] GPT:7812499 != 30560255 <4>[ 4.197158] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.197196] mmcblk2: p1 p2 p3 <4>[ 4.216720] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.216852] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.218241] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.223767] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.444731] hub 1-1:1.0: USB hub found <6>[ 4.444866] hub 1-1:1.0: 3 ports detected <4>[ 4.449611] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.449732] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.451111] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.204270] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.213851] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.243820] Sending DHCP requests ., OK <6>[ 7.283849] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 7.283874] IP-Config: Complete: <6>[ 7.283880] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.283907] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 7.283920] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.283935] nameserver0=192.168.201.1 <6>[ 7.292257] Freeing unused kernel memory: 2048K <6>[ 7.384792] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.514586] udevd[139]: starting version 3.2.9 <5>[ 7.515549] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.515857] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.515974] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.524859] udevd[139]: specified user 'tss' unknown <27>[ 7.525009] udevd[139]: specified group 'tss' unknown <30>[ 7.527522] udevd[140]: starting eudev-3.2.9 <6>[ 7.907155] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.909034] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.913586] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.913833] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.915697] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.922682] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.922831] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.924673] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.957698] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.957804] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.957912] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.958005] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.967340] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.967497] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.969129] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.072226] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.089711] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.113169] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.113288] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.113573] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.113657] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.113671] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.114301] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.188463] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.188573] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.188692] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.188776] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.197110] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.197303] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.199029] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.213786] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.268656] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.268721] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.268783] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.268825] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.274591] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.335354] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.335373] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.335382] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.364390] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.364582] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.366401] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.449556] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.449621] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.449688] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.449733] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.498230] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.498412] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.498579] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.498707] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.505299] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.505524] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.507880] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.524902] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.524967] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.525031] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.525075] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.525211] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.530326] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.533022] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.533160] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.534772] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.551464] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.551532] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.551589] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.551633] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.571523] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.571715] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.574401] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.580118] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.580201] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.580260] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.580308] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.856180] caam algorithms registered in /proc/crypto <6>[ 8.857553] caam 2100000.crypto: registering rng-caam <4>[ 8.862834] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.862997] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.864741] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.868202] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.868275] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.868344] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.868389] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.874553] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.874713] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.876456] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.879672] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.879734] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.879789] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.879833] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <5>[ 9.040042] random: crng init done <5>[ 9.040062] random: 1 urandom warning(s) missed due to ratelimiting done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-13433227/environment . /lava-13433227/environment / # /lava-13433227/bin/lava-test-runner /lava-13433227/0 /lava-13433227/bin/lava-test-runner /lava-13433227/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-13433227/0/tests/0_dmesg + cat uuid + UUID=13433227_1.5.2.4.1 + set +x + KERNELCI_LAVA<8>[ 9.878927] =y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.917860] <8>[ 9.956532] + set +x / # <8>[ 9.997393] <8>[ 9.998641]