Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.98 (1254 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 145777/tftp-deploy-kkuzejlp/kernel/Image tftp 0x82000000 145777/tftp-deploy-kkuzejlp/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.98; sending through gateway 172.16.0.254 Filename '145777/tftp-deploy-kkuzejlp/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 11.9 MiB/s done Bytes transferred = 31838720 (1e5d200 hex) => tftp 0x90080000 145777/tftp-deploy-kkuzejlp/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 145777/tftp-deploy-kkuzejlp/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.98; sending through gateway 172.16.0.254 Filename '145777/tftp-deploy-kkuzejlp/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 11.8 MiB/s done Bytes transferred = 18909575 (1208987 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 145777/tftp-deploy-kkuzejlp/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 145777/tftp-deploy-kkuzejlp/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.98; sending through gateway 172.16.0.254 Filename '145777/tftp-deploy-kkuzejlp/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6 MiB/s done Bytes transferred = 25279 (62bf hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2022-07-26 14:24:49 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18909511 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900092be WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.129-cip12 (KernelCI@build-j402888-arm64-gcc-10-defconfig-bmwx4) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Jul 26 14:01:37 UTC 2022 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7feb00-0x20ff800fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 23 pages/cpu s56600 r8192 d29416 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3897760K/4126720K available (14592K kernel code, 2804K rwdata, 7596K rodata, 5952K init, 514K bss, 196192K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008728] Console: colour dummy device 80x25 <6>[ 0.013517] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024235] pid_max: default: 32768 minimum: 301 <6>[ 0.029194] LSM: Security Framework initializing <6>[ 0.034165] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041920] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050997] rcu: Hierarchical SRCU implementation. <6>[ 0.056245] Platform MSI: gic-its@6020000 domain created <6>[ 0.061953] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069813] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075945] EFI services will not be available. <6>[ 0.080889] smp: Bringing up secondary CPUs ... <6>[ 0.085999] Detected PIPT I-cache on CPU1 <6>[ 0.086018] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.086024] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.086050] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.086107] smp: Brought up 1 node, 2 CPUs <6>[ 0.116420] SMP: Total of 2 processors activated. <6>[ 0.121432] CPU features: detected: 32-bit EL0 Support <6>[ 0.126890] CPU features: detected: CRC32 instructions <6>[ 0.132341] CPU features: detected: 32-bit EL1 Support <6>[ 0.148735] CPU: All CPU(s) started at EL2 <6>[ 0.153152] alternatives: patching kernel code <6>[ 0.158649] devtmpfs: initialized <4>[ 0.164323] KASLR disabled due to lack of seed <6>[ 0.169179] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.179287] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.186977] pinctrl core: initialized pinctrl subsystem <6>[ 0.193140] DMI not present or invalid. <6>[ 0.197664] NET: Registered protocol family 16 <6>[ 0.203165] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210659] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218904] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.227181] audit: initializing netlink subsys (disabled) <5>[ 0.233016] audit: type=2000 audit(0.148:1): state=initialized audit_enabled=0 res=1 <6>[ 0.233539] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.241104] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.247651] cpuidle: using governor menu <6>[ 0.258819] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.265960] ASID allocator initialised with 65536 entries <6>[ 0.272344] Serial: AMBA PL011 UART driver <6>[ 0.287551] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.295201] SoC family: QorIQ LS1028A <6>[ 0.299155] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.311723] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.318763] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.325793] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.332823] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.340603] cryptd: max_cpu_qlen set to 1000 <6>[ 0.346551] ACPI: Interpreter disabled. <6>[ 0.351659] iommu: Default domain type: Translated <6>[ 0.356964] vgaarb: loaded <5>[ 0.360099] SCSI subsystem initialized <6>[ 0.364370] usbcore: registered new interface driver usbfs <6>[ 0.370200] usbcore: registered new interface driver hub <6>[ 0.375842] usbcore: registered new device driver usb <6>[ 0.381452] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.389402] i2c i2c-0: IMX I2C adapter registered <6>[ 0.394583] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.402269] i2c i2c-1: IMX I2C adapter registered <6>[ 0.407380] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.415154] i2c i2c-2: IMX I2C adapter registered <6>[ 0.420455] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.425732] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.435232] PTP clock support registered <6>[ 0.439523] EDAC MC: Ver: 3.0.0 <6>[ 0.443709] FPGA manager framework <6>[ 0.447439] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.454257] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.460773] VFS: Disk quotas dquot_6.6.0 <6>[ 0.465025] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.472322] pnp: PnP ACPI: disabled <6>[ 0.479393] NET: Registered protocol family 2 <6>[ 0.484350] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.493411] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.502337] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.510684] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.518685] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.525652] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.532704] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.540259] NET: Registered protocol family 1 <6>[ 0.545225] RPC: Registered named UNIX socket transport module. <6>[ 0.551472] RPC: Registered udp transport module. <6>[ 0.556484] RPC: Registered tcp transport module. <6>[ 0.561496] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.568266] PCI: CLS 0 bytes, default 64 <6>[ 0.572574] Unpacking initramfs... <6>[ 1.205878] Freeing initrd memory: 18460K <6>[ 1.210515] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.219249] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.224431] kvm [1]: GICv3: no GICV resource entry <6>[ 1.229535] kvm [1]: disabling GICv2 emulation <6>[ 1.234296] kvm [1]: GIC system register CPU interface enabled <6>[ 1.240481] kvm [1]: vgic interrupt IRQ9 <6>[ 1.244765] kvm [1]: Hyp mode initialized successfully <5>[ 1.251221] Initialise system trusted keyrings <6>[ 1.256064] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.265939] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.272506] NFS: Registering the id_resolver key type <5>[ 1.277885] Key type id_resolver registered <5>[ 1.282374] Key type id_legacy registered <6>[ 1.286729] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.293759] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.301577] 9p: Installing v9fs 9p2000 file system support <5>[ 1.337313] Key type asymmetric registered <5>[ 1.341715] Asymmetric key parser 'x509' registered <6>[ 1.346919] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.354651] io scheduler mq-deadline registered <6>[ 1.359486] io scheduler kyber registered <6>[ 1.368900] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.377010] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 1.386157] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 1.395304] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 1.404448] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 1.413593] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 1.422738] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 1.431882] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 1.441069] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.450180] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.457474] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.463013] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 1.473729] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 1.484884] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.495608] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.506768] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 1.517484] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 1.528638] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 1.539370] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.545728] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.556537] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.567781] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.578849] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.590369] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.596179] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.606456] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.617331] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.623683] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.634488] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.645731] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.656798] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.668316] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.674124] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.684404] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.695237] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.701591] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.712396] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.723650] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.729569] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.735923] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.746731] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.757985] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.763897] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.770248] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.781056] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.792309] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.798223] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.804574] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.815381] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.826624] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.837439] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.843353] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.849704] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.860508] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.871762] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.878393] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.884759] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.893054] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.900720] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.909602] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.918566] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 1.925599] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 1.931401] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 1.937909] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 1.948816] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 1.955195] pci 0001:00:00.0: supports D1 D2 <6>[ 1.959768] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.967577] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 1.974526] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 1.979954] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 1.987616] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 1.996518] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.005472] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 2.012505] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 2.018308] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 2.027620] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.038525] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.044903] pci 0002:00:00.0: supports D1 D2 <6>[ 2.049477] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.057273] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.064221] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 2.070237] EINJ: ACPI disabled. <6>[ 2.081655] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.089572] printk: console [ttyS0] disabled <6>[ 2.094193] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.103353] printk: console [ttyS0] enabled <6>[ 2.103353] printk: console [ttyS0] enabled <6>[ 2.112295] printk: bootconsole [ns16550a0] disabled <6>[ 2.112295] printk: bootconsole [ns16550a0] disabled <6>[ 2.123125] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 2.132511] SuperH (H)SCI(F) driver initialized <6>[ 2.137624] msm_serial: driver initialized <6>[ 2.142376] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 2.152965] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 2.159709] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 2.164607] arm-smmu 5000000.iommu: stage 1 translation <5>[ 2.170200] arm-smmu 5000000.iommu: stage 2 translation <5>[ 2.175795] arm-smmu 5000000.iommu: nested translation <5>[ 2.181301] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 2.188728] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 2.195547] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 2.202275] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 2.209002] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 2.220252] loop: module loaded <6>[ 2.228794] megasas: 07.714.04.00-rc1 <6>[ 2.234933] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 2.249665] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 2.262548] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 2.269637] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 2.275144] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 2.282622] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 2.290593] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 2.298618] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 2.306595] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 2.314600] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 2.322591] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 2.330591] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 2.340345] tun: Universal TUN/TAP device driver, 1.6 <6>[ 2.346156] thunder_xcv, ver 1.0 <6>[ 2.349683] thunder_bgx, ver 1.0 <6>[ 2.353201] nicpf, ver 1.0 <6>[ 2.356694] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 2.470273] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 2.476789] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using e6:40:de:dc:2e:03 <6>[ 2.485615] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using be:eb:f9:cc:9c:8a <6>[ 2.504836] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 2.618268] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 2.625649] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 2.632019] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 2.742269] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 2.749074] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 2.755438] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 2.866268] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 2.873073] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 2.879497] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 2.990269] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 2.997444] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 3.003734] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 3.010660] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 3.019691] pps pps0: new PPS source ptp0 <6>[ 3.024442] hclge is initializing <6>[ 3.028045] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 3.035558] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 3.041181] e1000: Intel(R) PRO/1000 Network Driver <6>[ 3.046339] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 3.052401] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.057645] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.063875] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.069555] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.075428] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 3.081979] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 3.088383] sky2: driver version 1.30 <6>[ 3.092970] VFIO - User Level meta-driver version: 0.3 <6>[ 3.098744] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 3.104640] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 3.111297] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.118127] ehci-pci: EHCI PCI platform driver <6>[ 3.122871] ehci-platform: EHCI generic platform driver <6>[ 3.128456] ehci-orion: EHCI orion driver <6>[ 3.132801] ehci-exynos: EHCI Exynos driver <6>[ 3.137313] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.143787] ohci-pci: OHCI PCI platform driver <6>[ 3.148530] ohci-platform: OHCI generic platform driver <6>[ 3.154103] ohci-exynos: OHCI Exynos driver <6>[ 3.158839] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.164621] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.172721] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.182439] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 3.189039] hub 1-0:1.0: USB hub found <6>[ 3.193078] hub 1-0:1.0: 1 port detected <6>[ 3.197426] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.203205] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.211156] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.217995] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.226619] hub 2-0:1.0: USB hub found <6>[ 3.230656] hub 2-0:1.0: 1 port detected <6>[ 3.235056] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.240833] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 3.248917] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 3.258632] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 3.265163] hub 3-0:1.0: USB hub found <6>[ 3.269202] hub 3-0:1.0: 1 port detected <6>[ 3.273532] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 3.279307] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 3.287261] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.294101] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.302726] hub 4-0:1.0: USB hub found <6>[ 3.306767] hub 4-0:1.0: 1 port detected <6>[ 3.311308] usbcore: registered new interface driver usb-storage <6>[ 3.319198] i2c /dev entries driver <6>[ 3.325873] sp805-wdt c000000.watchdog: registration successful <6>[ 3.332181] sp805-wdt c010000.watchdog: registration successful <6>[ 3.339711] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 3.348434] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.354924] sdhci: Copyright(c) Pierre Ossman <6>[ 3.359886] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.366851] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.373313] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 3.373889] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 3.379272] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.392461] usbcore: registered new interface driver usbhid <6>[ 3.398325] usbhid: USB HID core driver <6>[ 3.405205] NET: Registered protocol family 17 <6>[ 3.410023] 9pnet: Installing 9P2000 support <6>[ 3.410277] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <5>[ 3.414616] Key type dns_resolver registered <6>[ 3.421745] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 3.426543] registered taskstats version 1 <5>[ 3.437823] Loading compiled-in X.509 certificates <6>[ 3.445215] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 3.453047] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 3.459069] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 3.465239] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 3.471239] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 3.479889] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 3.523669] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 3.526910] mmc0: new HS400 MMC card at address 0001 <6>[ 3.537317] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 3.539497] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 3.554396] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 3.559468] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB <6>[ 3.565929] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB <6>[ 3.572261] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (234:0) <6>[ 3.582744] mmcblk0: p1 p2 <6>[ 3.774497] hub 3-1:1.0: USB hub found <6>[ 3.778683] hub 3-1:1.0: 7 ports detected <6>[ 6.599190] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 6.626315] Sending DHCP requests ., OK <6>[ 6.646573] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.98 <6>[ 6.654572] IP-Config: Complete: <6>[ 6.658093] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.98, mask=255.255.255.0, gw=172.16.0.254 <6>[ 6.668550] host=172.16.0.98, domain=lava.lan, nis-domain=(none) <6>[ 6.675315] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 6.675327] nameserver0=8.8.8.8 <6>[ 6.686228] ALSA device list: <6>[ 6.689562] No soundcards found. <6>[ 6.696983] Freeing unused kernel memory: 5952K <6>[ 6.702087] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.758504] udevd[125]: starting version 3.2.9 <5>[ 6.763719] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.770632] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.777395] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.786899] udevd[125]: specified user 'tss' unknown <27>[ 6.792281] udevd[125]: specified group 'tss' unknown <30>[ 6.798577] udevd[126]: starting eudev-3.2.9 <6>[ 6.973391] mali-dp f080000.display: Adding to iommu group 13 <27>[ 7.045392] udevd[138]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 7.062590] NET: Registered protocol family 10 <6>[ 7.068164] Segment Routing with IPv6 <4>[ 7.094216] at24 0-0050: supply vcc not found, using dummy regulator <28>[ 7.109791] udevd[138]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <4>[ 7.125579] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 7.132686] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 7.139748] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 7.154695] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 7.162333] wm8904 2-001a: supply CPVDD not found, using dummy regulator <6>[ 7.169658] mscc_felix 0000:00:00.5: Adding to iommu group 14 <4>[ 7.178494] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 7.185054] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 7.194467] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 7.201051] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 7.208017] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 7.217482] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.224037] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 7.231968] wm8904 2-001a: revision A <4>[ 7.236966] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 7.244206] rtc-rv8803 0-0032: registered as rtc0 <4>[ 7.264683] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 7.273051] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <3>[ 7.281874] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 7.296586] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 7.411848] caam 8000000.crypto: Entropy delay = 3200 <6>[ 7.437400] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 7.457490] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 7.462999] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 7.470517] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 7.557129] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 7.563579] caam algorithms registered in /proc/crypto <6>[ 7.570074] caam 8000000.crypto: registering rng-caam <6>[ 7.575646] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 7.581656] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 7.587678] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.635710] random: crng init done <5>[ 7.639415] random: 4 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-145777/environment . /lava-145777/environment / # /lava-145777/bin/lava-test-runner /lava-145777/0 /lava-145777/bin/lava-test-runner /lava-145777/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 8.191622] d /lava-145777/0/tests/0_dmesg + cat uuid + UUID=145777_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.211135] <8>[ 8.231199] <8>[ 8.252456] + set +x <8>[ 8.262040] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-145777/environment / # . /lava-145777/environment/lava-145777/bin/lava-test-runner /lava-145777/1 / # /lava-145777/bin/lava-test-runner /lava-145777/1 + export 'TESTRUN_ID=1_bootrr' + <8>[ 8.712554] cd /lava-145777/1/tests/1_bootrr + cat uuid + UUID=145777_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-145777/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-145777/1/../bin/lava-test-case <8>[ 9.733040] /lava-145777/1/../bin/lava-test-case <8>[ 9.751916] /lava-145777/1/../bin/lava-test-case <8>[ 9.764899] /lava-145777/1/../bin/lava-test-case <8>[ 9.784841] /lava-145777/1/../bin/lava-test-case <8>[ 9.800508] /lava-145777/1/../bin/lava-test-case <8>[ 9.815068] /lava-145777/1/../bin/lava-test-case <8>[ 9.831207] /lava-145777/1/../bin/lava-test-case <8>[ 9.846639] /lava-145777/1/../bin/lava-test-case <8>[ 9.862914] /lava-145777/1/../bin/lava-test-case <8>[ 9.878190] /lava-145777/1/../bin/lava-test-case <8>[ 9.893487] /lava-145777/1/../bin/lava-test-case <8>[ 9.908083] /lava-145777/1/../bin/lava-test-case <8>[ 9.923176] /lava-145777/1/../bin/lava-test-case <8>[ 9.937427] /lava-145777/1/../bin/lava-test-case <8>[ 9.952876] /lava-145777/1/../bin/lava-test-case <8>[ 9.967448] /lava-145777/1/../bin/lava-test-case <8>[ 9.982942] /lava-145777/1/../bin/lava-test-case <8>[ 9.998158] /lava-145777/1/../bin/lava-test-case <8>[ 10.016183] /lava-145777/1/../bin/lava-test-case <8>[ 10.032068] /lava-145777/1/../bin/lava-test-case <8>[ 10.050900] /lava-145777/1/../bin/lava-test-case <8>[ 10.066334] /lava-145777/1/../bin/lava-test-case <8>[ 10.081670] /lava-145777/1/../bin/lava-test-case <8>[ 10.097614] /lava-145777/1/../bin/lava-test-case <8>[ 10.116952] /lava-145777/1/../bin/lava-test-case <8>[ 10.132784] /lava-145777/1/../bin/lava-test-case <8>[ 10.147899] /lava-145777/1/../bin/lava-test-case <8>[ 10.163466] /lava-145777/1/../bin/lava-test-case <8>[ 10.178197] /lava-145777/1/../bin/lava-test-case <8>[ 10.193707] /lava-145777/1/../bin/lava-test-case <8>[ 10.208963] /lava-145777/1/../bin/lava-test-case <8>[ 10.224231] /lava-145777/1/../bin/lava-test-case <8>[ 10.239477] /lava-145777/1/../bin/lava-test-case <8>[ 10.255134] /lava-145777/1/../bin/lava-test-case <8>[ 10.269713] /lava-145777/1/../bin/lava-test-case <8>[ 10.288212] /lava-145777/1/../bin/lava-test-case <8>[ 10.303489] /lava-145777/1/../bin/lava-test-case <8>[ 10.319366] /lava-145777/1/../bin/lava-test-case <8>[ 10.334757] /lava-145777/1/../bin/lava-test-case <8>[ 10.349901] /lava-145777/1/../bin/lava-test-case <8>[ 10.365710] /lava-145777/1/../bin/lava-test-case <8>[ 10.381296] /lava-145777/1/../bin/lava-test-case <8>[ 10.396626] /lava-145777/1/../bin/lava-test-case <8>[ 10.412362] /lava-145777/1/../bin/lava-test-case <8>[ 10.427760] /lava-145777/1/../bin/lava-test-case <8>[ 10.443352] /lava-145777/1/../bin/lava-test-case <8>[ 10.457959] /lava-145777/1/../bin/lava-test-case <8>[ 10.474009] /lava-145777/1/../bin/lava-test-case <8>[ 10.489739] /lava-145777/1/../bin/lava-test-case <8>[ 10.508191] /lava-145777/1/../bin/lava-test-case <8>[ 10.523393] /lava-145777/1/../bin/lava-test-case <8>[ 10.538309] /lava-145777/1/../bin/lava-test-case <8>[ 10.556132] /lava-145777/1/../bin/lava-test-case <8>[ 10.572288] /lava-145777/1/../bin/lava-test-case <8>[ 10.588177] /lava-145777/1/../bin/lava-test-case <8>[ 10.606878] /lava-145777/1/../bin/lava-test-case <8>[ 10.622799] /lava-145777/1/../bin/lava-test-case <8>[ 10.637332] /lava-145777/1/../bin/lava-test-case <8>[ 10.652741] /lava-145777/1/../bin/lava-test-case <8>[ 10.667036] /lava-145777/1/../bin/lava-test-case <8>[ 10.682516] /lava-145777/1/../bin/lava-test-case <8>[ 10.700377] /lava-145777/1/../bin/lava-test-case <8>[ 10.715516] /lava-145777/1/../bin/lava-test-case <8>[ 10.730614] /lava-145777/1/../bin/lava-test-case <8>[ 10.745766] /lava-145777/1/../bin/lava-test-case <8>[ 10.764328] /lava-145777/1/../bin/lava-test-case <8>[ 10.780817] /lava-145777/1/../bin/lava-test-case <8>[ 10.796567] /lava-145777/1/../bin/lava-test-case <8>[ 10.812610] /lava-145777/1/../bin/lava-test-case <8>[ 10.827682] /lava-145777/1/../bin/lava-test-case <8>[ 10.844038] /lava-145777/1/../bin/lava-test-case <8>[ 11.861377] /lava-145777/1/../bin/lava-test-case <8>[ 12.880064] /lava-145777/1/../bin/lava-test-case <8>[ 13.897453] /lava-145777/1/../bin/lava-test-case <8>[ 14.916121] /lava-145777/1/../bin/lava-test-case <8>[ 14.931777] /lava-145777/1/../bin/lava-test-case <8>[ 14.947773] /lava-145777/1/../bin/lava-test-case <8>[ 14.962968] /lava-145777/1/../bin/lava-test-case <8>[ 14.978956] /lava-145777/1/../bin/lava-test-case <8>[ 14.993800] /lava-145777/1/../bin/lava-test-case <8>[ 15.009784] /lava-145777/1/../bin/lava-test-case <8>[ 15.024986] /lava-145777/1/../bin/lava-test-case <8>[ 15.040734] /lava-145777/1/../bin/lava-test-case <8>[ 15.055988] /lava-145777/1/../bin/lava-test-case <8>[ 15.071207] /lava-145777/1/../bin/lava-test-case <8>[ 15.087235] /lava-145777/1/../bin/lava-test-case <8>[ 15.102657] /lava-145777/1/../bin/lava-test-case <8>[ 15.117879] /lava-145777/1/../bin/lava-test-case <8>[ 15.133458] /lava-145777/1/../bin/lava-test-case <8>[ 15.148655] /lava-145777/1/../bin/lava-test-case <8>[ 15.164683] /lava-145777/1/../bin/lava-test-case <8>[ 15.179815] /lava-145777/1/../bin/lava-test-case <8>[ 15.195118] /lava-145777/1/../bin/lava-test-case <8>[ 15.209594] /lava-145777/1/../bin/lava-test-case <8>[ 15.224645] /lava-145777/1/../bin/lava-test-case <8>[ 15.239737] /lava-145777/1/../bin/lava-test-case <8>[ 15.254650] /lava-145777/1/../bin/lava-test-case <8>[ 15.270184] /lava-145777/1/../bin/lava-test-case <8>[ 16.290051] /lava-145777/1/../bin/lava-test-case <8>[ 17.309082] + set +x <8>[ 17.318873] / #