[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12210301/tftp-deploy-84cypx1o/kernel/zImage tftp 0x10000000 12210301/tftp-deploy-84cypx1o/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12210301/tftp-deploy-84cypx1o/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 14 MiB/s done Bytes transferred = 9708032 (942200 hex) => tftp 0x14000000 12210301/tftp-deploy-84cypx1o/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12210301/tftp-deploy-84cypx1o/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12210301/tftp-deploy-84cypx1o/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 14 MiB/s done Bytes transferred = 12152570 (b96efa hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12210301/tftp-deploy-84cypx1o/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12210301/tftp-deploy-84cypx1o/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12210301/tftp-deploy-84cypx1o/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12210301/extract-nfsrootfs-p0m28loh,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12210301/extract-nfsrootfs-p0m28loh,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x942200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12152506 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j37949-arm-gcc-10-multi-v7-defconfig-pncrh) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Dec 7 19:44:33 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12210301/extract-nfsrootfs-p0m28loh,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936488K/1048576K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 46552K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022199] Console: colour dummy device 80x30 <6>[ 0.024093] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034500] CPU: Testing write buffer coherency: ok <6>[ 0.039632] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044930] pid_max: default: 32768 minimum: 301 <6>[ 0.049958] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057395] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066272] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072009] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079689] rcu: Hierarchical SRCU implementation. <6>[ 0.086684] EFI services will not be available. <6>[ 0.088920] smp: Bringing up secondary CPUs ... <6>[ 0.094222] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094230] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105565] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105573] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116768] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116776] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127204] smp: Brought up 1 node, 4 CPUs <6>[ 0.131427] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137886] CPU: All CPU(s) started in SVC mode. <6>[ 0.143307] devtmpfs: initialized <6>[ 0.153830] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159176] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169044] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179260] pinctrl core: initialized pinctrl subsystem <6>[ 0.183750] DMI not present or invalid. <6>[ 0.186852] NET: Registered protocol family 16 <6>[ 0.194127] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200761] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200945] cpuidle: using governor menu <6>[ 0.209062] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.387707] vdd1p1: supplied by regulator-dummy <6>[ 0.396839] vdd3p0: supplied by regulator-dummy <6>[ 0.405840] vdd2p5: supplied by regulator-dummy <6>[ 0.414875] vddarm: supplied by regulator-dummy <6>[ 0.424071] vddpu: supplied by regulator-dummy <6>[ 0.432886] vddsoc: supplied by regulator-dummy <6>[ 0.760662] No ATAGs? <6>[ 0.760848] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.768624] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.778823] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.789095] Serial: AMBA PL011 UART driver <6>[ 0.793249] printk: console [ramoops-1] enabled <6>[ 0.795601] pstore: Registered ramoops as persistent store backend <6>[ 0.801825] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.839390] iommu: Default domain type: Translated <6>[ 0.842114] vgaarb: loaded <5>[ 0.845503] SCSI subsystem initialized <6>[ 0.849262] usbcore: registered new interface driver usbfs <6>[ 0.854421] usbcore: registered new interface driver hub <6>[ 0.860025] usbcore: registered new device driver usb <6>[ 0.866846] i2c i2c-0: IMX I2C adapter registered <6>[ 0.871533] i2c i2c-1: IMX I2C adapter registered <6>[ 0.876007] i2c i2c-2: IMX I2C adapter registered <6>[ 0.881475] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.885355] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.894786] PTP clock support registered <6>[ 0.902777] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.054928] NET: Registered protocol family 2 <6>[ 2.057139] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.065747] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.073030] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.081048] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.088533] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.095228] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.101890] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.109365] NET: Registered protocol family 1 <6>[ 2.114413] RPC: Registered named UNIX socket transport module. <6>[ 2.119951] RPC: Registered udp transport module. <6>[ 2.124944] RPC: Registered tcp transport module. <6>[ 2.129866] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.136592] PCI: CLS 0 bytes, default 64 <6>[ 2.141245] Trying to unpack rootfs image as initramfs... <6>[ 3.096389] Freeing initrd memory: 11868K <4>[ 3.098371] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.105694] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.115441] Initialise system trusted keyrings <6>[ 3.118702] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.130860] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.134856] NFS: Registering the id_resolver key type <5>[ 3.139457] Key type id_resolver registered <5>[ 3.143875] Key type id_legacy registered <6>[ 3.148212] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.155092] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.162782] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.167807] Key type asymmetric registered <5>[ 3.171692] Asymmetric key parser 'x509' registered <6>[ 3.176896] bounce: pool size: 64 pages <6>[ 3.180945] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.188590] io scheduler mq-deadline registered <6>[ 3.193369] io scheduler kyber registered <6>[ 3.237496] mxs-dma 110000.dma-controller: initialized <4>[ 3.244860] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.252668] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.309560] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.317721] SuperH (H)SCI(F) driver initialized <6>[ 3.320686] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.329569] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.337469] printk: console [ttymxc1] enabled <6>[ 3.337469] printk: console [ttymxc1] enabled <6>[ 3.346638] printk: bootconsole [ec_imx21] disabled <6>[ 3.346638] printk: bootconsole [ec_imx21] disabled <6>[ 3.358393] msm_serial: driver initialized <6>[ 3.364415] STMicroelectronics ASC driver initialized <6>[ 3.371702] STM32 USART driver initialized <4>[ 3.386553] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.394476] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.401225] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.417810] brd: module loaded <6>[ 3.428541] loop: module loaded <6>[ 3.435952] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.444170] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.452444] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.460905] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.468911] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.476654] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.484242] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.494756] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.502014] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.511094] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.521892] scsi host0: ahci-imx <6>[ 3.525802] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.546515] CAN device driver interface <6>[ 3.551959] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.561500] pps pps0: new PPS source ptp0 <6>[ 3.583776] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.591379] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.596649] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.602915] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.608580] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.620610] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.628346] usbcore: registered new interface driver pegasus <6>[ 3.634338] usbcore: registered new interface driver asix <6>[ 3.640038] usbcore: registered new interface driver ax88179_178a <6>[ 3.646450] usbcore: registered new interface driver cdc_ether <6>[ 3.652593] usbcore: registered new interface driver smsc75xx <6>[ 3.658668] usbcore: registered new interface driver smsc95xx <6>[ 3.664729] usbcore: registered new interface driver net1080 <6>[ 3.670708] usbcore: registered new interface driver cdc_subset <6>[ 3.676945] usbcore: registered new interface driver zaurus <6>[ 3.682874] usbcore: registered new interface driver cdc_ncm <6>[ 3.692400] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.699221] ehci-pci: EHCI PCI platform driver <6>[ 3.703993] ehci-platform: EHCI generic platform driver <6>[ 3.709788] ehci-orion: EHCI orion driver <6>[ 3.714323] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.718792] ehci-st: EHCI STMicroelectronics driver <6>[ 3.724148] ehci-exynos: EHCI Exynos driver <6>[ 3.728785] ehci-atmel: EHCI Atmel driver <6>[ 3.733280] tegra-ehci: Tegra EHCI driver <6>[ 3.737775] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.744259] ohci-pci: OHCI PCI platform driver <6>[ 3.749012] ohci-platform: OHCI generic platform driver <6>[ 3.754787] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.759258] ohci-st: OHCI STMicroelectronics driver <6>[ 3.764629] ohci-atmel: OHCI Atmel driver <6>[ 3.770162] usbcore: registered new interface driver usb-storage <6>[ 3.784841] i2c /dev entries driver <6>[ 3.808642] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.815136] sdhci: Copyright(c) Pierre Ossman <6>[ 3.822581] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.830887] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.838116] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.842413] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.843420] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.854158] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.861532] usbcore: registered new interface driver usbhid <6>[ 3.867400] usbhid: USB HID core driver <6>[ 3.874180] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.878286] NET: Registered protocol family 10 <6>[ 3.879893] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.885538] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.885638] Segment Routing with IPv6 <6>[ 3.885713] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.886292] NET: Registered protocol family 17 <6>[ 3.886304] can: controller area network core <6>[ 3.886378] NET: Registered protocol family 29 <6>[ 3.886384] can: raw protocol <6>[ 3.886392] can: broadcast manager protocol <6>[ 3.886402] can: netlink gateway - max_hops=1 <5>[ 3.886836] Key type dns_resolver registered <6>[ 3.891152] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.893149] ThumbEE CPU extension supported. <5>[ 3.893162] Registering SWP/SWPB emulation handler <5>[ 3.898548] Loading compiled-in X.509 certificates <6>[ 3.905752] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.917951] pstore: Using crash dump compression: deflate <6>[ 3.951476] mmc2: new high speed SDHC card at address 0001 <4>[ 3.977762] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 3.981130] mmcblk2: mmc2:0001 SD 14.8 GiB <4>[ 3.988151] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.000975] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.010922] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.018649] GPT:29296874 != 30965759 <4>[ 4.022514] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.028813] GPT:29296874 != 30965759 <4>[ 4.032666] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.038168] mmcblk2: p1 p2 p3 <4>[ 4.044351] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.054254] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.059420] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.092805] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.099921] hub 1-0:1.0: USB hub found <6>[ 4.104126] hub 1-0:1.0: 1 port detected <6>[ 4.112792] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.129629] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.137557] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.145460] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.157516] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.165436] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.173294] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.183334] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.195393] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.203309] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.211187] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.224808] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.432725] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.634325] hub 1-1:1.0: USB hub found <6>[ 4.638541] hub 1-1:1.0: 3 ports detected <4>[ 4.648864] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.656832] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.665106] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.363160] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.382782] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.412725] Sending DHCP requests ., OK <6>[ 7.456919] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 7.465246] IP-Config: Complete: <6>[ 7.468767] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.479523] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 7.487665] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.487678] nameserver0=192.168.201.1 <6>[ 7.508735] Freeing unused kernel memory: 2048K <6>[ 7.533179] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.361491] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.372868] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.380857] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.403031] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.413381] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.424202] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.432136] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.454022] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.467896] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.470053] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.475875] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.484325] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.494888] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.499261] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.513220] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.515635] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.523422] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.551639] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.582982] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.590168] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.590697] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.601864] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.609174] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.663106] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.697573] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.705695] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.714327] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.720426] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.722385] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.723861] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.723876] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.723882] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.731762] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.769702] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.776773] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.783220] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.791828] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.813291] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.821823] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.830415] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.839020] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.884306] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.892239] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.914648] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.936180] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.944782] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.953351] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.961864] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.194428] caam algorithms registered in /proc/crypto <6>[ 9.201251] caam 2100000.crypto: registering rng-caam <4>[ 9.208442] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.216498] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.233871] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting<6>[ 9.249326] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) root file system ... <6>[ 9.259868] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/nfs-top .<6>[ 9.270199] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) .. done. <6>[ 9.281480] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/nfs-premo<4>[ 9.292817] panel-simple panel-lcd: supply power not found, using dummy regulator unt ... Waiting up to 60 secs for<4>[ 9.301554] panel-simple panel-lcd: Specify missing connector_type any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 9.389065] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.163028] systemd[1]: System time before build time, advancing clock. <30>[ 10.235723] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.259841] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.305179] systemd[1]: Set hostname to . <30>[ 11.068028] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.077373] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.090196] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.099892] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.134024] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.173408] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.213737] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.253522] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.293065] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.333331] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.346073] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.383691] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.412912] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.453034] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.483286] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.513959] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.588060] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.597984] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.634391] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.675192] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.716375] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.753479] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.794017] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.803656] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.816190] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.856869] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.897351] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.939548] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 11.976513] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.019363] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.056314] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.069482] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.112460] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.155342] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.196634] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.249298] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.283395] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.323960] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.381415] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 12.705041] systemd-journald[271]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.201-cip41 #1 SMP Thu Dec 7 19:44:33 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12210301/extract-nfsrootfs-p0m28loh' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12210301/extract-nfsrootfs-p0m28loh' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12210301/environment . /lava-12210301/environment / # /lava-12210301/bin/lava-test-runner /lava-12210301/0 /lava-12210301/bin/lava-test-runner /lava-12210301/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12210301/0/tests/0_timesync-off ++ cat uuid + UUID=12210301_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-12210301/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=12210301_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip/linux-5.10.y-cip/v5.10.201-cip41-28-ga386bc478aa6b/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-12-07 20:08:15-- http://storage.kernelci.org/cip/linux-5.10.y-cip/v5.10.201-cip41-28-ga386bc478aa6b/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1410888 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 2%[ ] 28.01K 70.5KB/s kselftest.tar.xz 2%[ ] 36.01K 54.4KB/s kselftest.tar.xz 11%[=> ] 151.96K 143KB/s kselftest.tar.xz 15%[==> ] 213.25K 161KB/s kselftest.tar.xz 18%[==> ] 252.36K 159KB/s kselftest.tar.xz 19%[==> ] 268.40K 145KB/s kselftest.tar.xz 21%[===> ] 293.85K 135KB/s kselftest.tar.xz 23%[===> ] 317.89K 133KB/s kselftest.tar.xz 24%[===> ] 339.10K 128KB/s kselftest.tar.xz 26%[====> ] 358.90K 123KB/s kselftest.tar.xz 27%[====> ] 378.70K 119KB/s eta 8s kselftest.tar.xz 29%[====> ] 406.98K 118KB/s eta 8s kselftest.tar.xz 30%[=====> ] 422.05K 114KB/s eta 8s kselftest.tar.xz 32%[=====> ] 449.40K 113KB/s eta 8s kselftest.tar.xz 33%[=====> ] 464.47K 110KB/s eta 8s kselftest.tar.xz 35%[======> ] 486.17K 110KB/s eta 8s kselftest.tar.xz 36%[======> ] 500.31K 108KB/s eta 8s kselftest.tar.xz 37%[======> ] 518.69K 107KB/s eta 8s kselftest.tar.xz 38%[======> ] 537.07K 109KB/s eta 8s kselftest.tar.xz 40%[=======> ] 558.28K 112KB/s eta 8s kselftest.tar.xz 42%[=======> ] 579.50K 95.6KB/s eta 8s kselftest.tar.xz 43%[=======> ] 604.95K 88.5KB/s eta 8s kselftest.tar.xz 46%[========> ] 634.16K 86.1KB/s eta 8s kselftest.tar.xz 48%[========> ] 662.92K 88.8KB/s eta 7s kselftest.tar.xz 49%[========> ] 684.14K 88.0KB/s eta 7s kselftest.tar.xz 51%[=========> ] 709.59K 89.6KB/s eta 7s kselftest.tar.xz 53%[=========> ] 733.63K 91.7KB/s eta 7s kselftest.tar.xz 55%[==========> ] 764.74K 95.8KB/s eta 7s kselftest.tar.xz 57%[==========> ] 793.02K 96.4KB/s eta 5s kselftest.tar.xz 59%[==========> ] 818.47K 101KB/s eta 5s kselftest.tar.xz 61%[===========> ] 853.34K 102KB/s eta 5s kselftest.tar.xz 64%[===========> ] 883.52K 105KB/s eta 5s kselftest.tar.xz 66%[============> ] 913.21K 107KB/s eta 4s kselftest.tar.xz 67%[============> ] 933.94K 106KB/s eta 4s kselftest.tar.xz 69%[============> ] 962.22K 107KB/s eta 4s kselftest.tar.xz 71%[=============> ] 985.33K 106KB/s eta 4s kselftest.tar.xz 72%[=============> ] 1005K 104KB/s eta 4s kselftest.tar.xz 74%[=============> ] 1.00M 103KB/s eta 4s kselftest.tar.xz 76%[==============> ] 1.03M 102KB/s eta 4s kselftest.tar.xz 78%[==============> ] 1.05M 101KB/s eta 4s kselftest.tar.xz 79%[==============> ] 1.07M 101KB/s eta 3s kselftest.tar.xz 80%[===============> ] 1.09M 99.5KB/s eta 3s kselftest.tar.xz 82%[===============> ] 1.11M 98.6KB/s eta 3s kselftest.tar.xz 84%[===============> ] 1.13M 96.6KB/s eta 3s kselftest.tar.xz 86%[================> ] 1.16M 95.6KB/s eta 2s kselftest.tar.xz 87%[================> ] 1.18M 92.5KB/s eta 2s kselftest.tar.xz 90%[=================> ] 1.21M 88.8KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.24M 89.9KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.27M 88.0KB/s eta 1s kselftest.tar.xz 96%[==================> ] 1.29M 87.9KB/s eta 1s kselftest.tar.xz 98%[==================> ] 1.32M 87.9KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.34M 90.9KB/s in 14s 2023-12-07 20:08:29 (101 KB/s) - 'kselftest.tar.xz' saved [1410888/1410888] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== shardfile-filesystems pass <12>[ 45.374845] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #