Trying 192.168.1.205... Connected to ts5. Escape character is '^]'. ser2net port telnet,2002 device serialdev,/dev/ttyUSB-lf-bbb-02,115200n81,local [] (Debian GNU/Linux) U-Boot SPL 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) Trying to boot from MMC2 U-Boot 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 172.16.3.131 (69 ms) => setenv serverip 172.16.3.3 setenv serverip 172.16.3.3 => tftp 0x82000000 1123298/tftp-deploy-7wftwced/kernel/zImage tftp 0x82000000 1123298/tftp-deploy-7wftwced/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.131 Filename '1123298/tftp-deploy-7wftwced/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 3.8 MiB/s done Bytes transferred = 4610016 (4657e0 hex) => tftp 0x83000000 1123298/tftp-deploy-7wftwced/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1123298/tftp-deploy-7wftwced/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.131 Filename '1123298/tftp-deploy-7wftwced/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 13.5 MiB 3.6 MiB/s done Bytes transferred = 14165752 (d826f8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1123298/tftp-deploy-7wftwced/dtb/am335x-boneblack.dtb tftp 0x88000000 1123298/tftp-deploy-7wftwced/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.131 Filename '1123298/tftp-deploy-7wftwced/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 3.2 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x4657e0 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-04-23 2:04:59 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14165688 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.214-cip46 (KernelCI@build-j174492-arm-gcc-10-omap2plus-defconfig-ngpsb) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Apr 23 01:39:12 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472032K/522240K available (9216K kernel code, 1027K rwdata, 2176K rodata, 1024K init, 278K bss, 33824K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018564] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030222] Console: colour dummy device 80x30 <3>[ 0.035089] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042145] This ensures that you still see kernel messages. Please <3>[ 0.048869] update your kernel commandline. <6>[ 0.053470] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095540] CPU: Testing write buffer coherency: ok <6>[ 0.100916] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106380] pid_max: default: 32768 minimum: 301 <6>[ 0.111541] LSM: Security Framework initializing <6>[ 0.116639] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124454] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134103] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140626] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147825] rcu: Hierarchical SRCU implementation. <6>[ 0.153608] smp: Bringing up secondary CPUs ... <6>[ 0.158544] smp: Brought up 1 node, 1 CPU <6>[ 0.162970] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169697] CPU: All CPU(s) started in SVC mode. <6>[ 0.175413] devtmpfs: initialized <6>[ 0.191259] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199855] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210294] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218782] pinctrl core: initialized pinctrl subsystem <6>[ 0.226418] NET: Registered protocol family 16 <6>[ 0.234010] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260503] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266596] audit: initializing netlink subsys (disabled) <6>[ 0.273666] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273679] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280285] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287018] cpuidle: using governor menu <5>[ 1.157866] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.282109] No ATAGs? <6>[ 1.284734] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.309095] Kprobes globally optimized <6>[ 1.322318] iommu: Default domain type: Translated <6>[ 1.329431] vgaarb: loaded <5>[ 1.333010] SCSI subsystem initialized <6>[ 1.338068] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.343568] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.353298] PTP clock support registered <6>[ 1.359109] clocksource: Switched to clocksource dmtimer <5>[ 1.997194] VFS: Disk quotas dquot_6.6.0 <6>[ 2.001701] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.018385] NET: Registered protocol family 2 <6>[ 2.023561] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.032220] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.041180] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.049477] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.057136] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.064078] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.071107] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.078715] NET: Registered protocol family 1 <6>[ 2.084513] RPC: Registered named UNIX socket transport module. <6>[ 2.090975] RPC: Registered udp transport module. <6>[ 2.096082] RPC: Registered tcp transport module. <6>[ 2.101209] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.108115] PCI: CLS 0 bytes, default 64 <6>[ 2.113166] Trying to unpack rootfs image as initramfs... <6>[ 3.099418] Freeing initrd memory: 13836K <6>[ 3.104985] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.115412] Initialise system trusted keyrings <6>[ 3.120843] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.129103] NFS: Registering the id_resolver key type <5>[ 3.134631] Key type id_resolver registered <5>[ 3.139252] Key type id_legacy registered <6>[ 3.143698] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.151682] Key type asymmetric registered <5>[ 3.156172] Asymmetric key parser 'x509' registered <6>[ 3.161521] io scheduler mq-deadline registered <6>[ 3.166451] io scheduler kyber registered <3>[ 3.303722] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.312429] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.420557] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.462358] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.533754] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.542456] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.602038] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.610725] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.628083] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.636790] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.700167] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.708624] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.735824] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.750476] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.761534] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.770959] printk: console [ttyS0] enabled <6>[ 3.770959] printk: console [ttyS0] enabled <6>[ 3.780027] printk: bootconsole [omap8250] disabled <6>[ 3.780027] printk: bootconsole [omap8250] disabled <6>[ 3.803884] brd: module loaded <6>[ 3.814598] loop: module loaded <3>[ 3.820319] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.888818] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.931533] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.941441] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.948094] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.953913] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.961475] cpsw 4a100000.ethernet: Detected MACID = 04:79:b7:e7:06:e0 <6>[ 3.970528] i2c /dev entries driver <5>[ 3.976057] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 3.983986] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.990527] sdhci: Copyright(c) Pierre Ossman <6>[ 3.995878] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.004184] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.013999] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.022444] Initializing XFRM netlink socket <6>[ 4.027243] NET: Registered protocol family 10 <6>[ 4.033672] Segment Routing with IPv6 <6>[ 4.037718] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.044789] NET: Registered protocol family 17 <6>[ 4.049645] NET: Registered protocol family 15 <5>[ 4.054484] Key type dns_resolver registered <6>[ 4.059673] oprofile: using arm/armv7 <6>[ 4.063716] ThumbEE CPU extension supported. <5>[ 4.068280] Registering SWP/SWPB emulation handler <3>[ 4.073830] omap_voltage_late_init: Voltage driver support not added <3>[ 4.080547] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.088962] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.097620] SmartReflex Class3 initialized <6>[ 4.102601] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.111512] Loading compiled-in X.509 certificates <6>[ 4.136568] OMAP GPIO hardware version 0.1 <4>[ 4.169504] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.183170] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.191951] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.198266] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.208203] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.219702] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.228713] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.233970] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.247227] mmc1: new high speed MMC card at address 0001 <6>[ 4.254084] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.259656] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.266313] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.272926] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.282465] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.291456] mmcblk1: p1 <6>[ 4.299710] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.390358] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 6.529493] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.538826] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.568963] Sending DHCP requests ., OK <6>[ 6.672935] IP-Config: Got DHCP answer from 172.16.3.3, my address is 172.16.3.131 <6>[ 6.680851] IP-Config: Complete: <6>[ 6.684361] device=eth0, hwaddr=04:79:b7:e7:06:e0, ipaddr=172.16.3.131, mask=255.255.255.0, gw=172.16.3.3 <6>[ 6.694691] host=172.16.3.131, domain=denx.de, nis-domain=(none) <6>[ 6.701441] bootserver=172.16.3.33, rootserver=172.16.3.33, rootpath= <6>[ 6.701447] nameserver0=172.16.3.3 <6>[ 6.712742] ntpserver0=172.16.3.3 <6>[ 6.719671] Freeing unused kernel memory: 1024K <6>[ 6.729328] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.964563] udevd[100]: starting version 3.2.9 <5>[ 6.971314] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.978529] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.986175] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.003588] udevd[100]: specified user 'tss' unknown <27>[ 7.009491] udevd[100]: specified group 'tss' unknown <30>[ 7.021574] udevd[101]: starting eudev-3.2.9 <6>[ 7.845686] remoteproc remoteproc0: wkup_m3 is available <4>[ 7.884841] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 7.894083] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 7.959286] usbcore: registered new interface driver usbfs <6>[ 7.965146] usbcore: registered new interface driver hub <6>[ 7.970951] usbcore: registered new device driver usb <4>[ 8.148468] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.157647] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.343648] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 8.349472] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.539234] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 8.547829] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 8.555439] usb usb1: Product: MUSB HDRC host driver <6>[ 8.560714] usb usb1: Manufacturer: Linux 5.10.214-cip46 musb-hcd <6>[ 8.567096] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 8.859694] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 8.865114] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <6>[ 8.909026] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <4>[ 8.985172] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 8.993320] hub 1-0:1.0: USB hub found <6>[ 9.029028] hub 1-0:1.0: 1 port detected <4>[ 9.132706] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 9.140182] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 9.147739] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 9.279637] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <3>[ 9.303599] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 9.340834] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 9.453007] at24 2-0056: supply vcc not found, using dummy regulator <3>[ 9.559600] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 9.584781] davinci-mcasp 48038000.mcasp: IRQ common not found <4>[ 9.631231] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 9.676938] tda998x 0-0070: found TDA19988 <3>[ 9.711671] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 9.826541] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.899490] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 9.929075] remoteproc remoteproc0: powering up wkup_m3 <4>[ 9.934749] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 9.944617] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 9.950858] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 10.612804] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 10.661176] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 10.724891] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.745141] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.761109] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 10.768599] random: crng init done <3>[ 10.924642] PM: Cannot get wkup_m3_ipc handle <6>[ 11.172711] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 11.232400] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 11.258561] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 11.295955] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 11.350174] PM: Cannot get wkup_m3_ipc handle <3>[ 11.390091] PM: Cannot get wkup_m3_ipc handle <3>[ 11.844381] PM: Cannot get wkup_m3_ipc handle <3>[ 11.879080] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1123298/environment . /lava-1123298/environment / # /lava-1123298/bin/lava-test-runner /lava-1123298/0 /lava-1123298/bin/lava-test-runner /lava-1123298/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1123298/0/tests/0_dmesg + cat uuid + UUID=1123298_1.5.2.4.1 + <8>[ 12.776361] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.843392] <8>[ 12.904289] <8>[ 12.965262] + set +x <8>[ 12.976378] / #