Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.127 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 501860/tftp-deploy-ucxfbi66/kernel/Image tftp 0x82000000 501860/tftp-deploy-ucxfbi66/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.127; sending through gateway 172.16.0.254 Filename '501860/tftp-deploy-ucxfbi66/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 14.4 MiB/s done Bytes transferred = 37900800 (2425200 hex) => tftp 0x90080000 501860/tftp-deploy-ucxfbi66/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 501860/tftp-deploy-ucxfbi66/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.127; sending through gateway 172.16.0.254 Filename '501860/tftp-deploy-ucxfbi66/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################## 15.5 MiB/s done Bytes transferred = 22203117 (152caed hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 501860/tftp-deploy-ucxfbi66/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 501860/tftp-deploy-ucxfbi66/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.127; sending through gateway 172.16.0.254 Filename '501860/tftp-deploy-ucxfbi66/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 6.9 MiB/s done Bytes transferred = 28772 (7064 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-10-04 18:39:58 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22203053 Bytes = 21.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a063 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.111-cip29 (KernelCI@build-j332753-arm64-gcc-12-defconfig-czqqd) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Fri Oct 4 18:26:39 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f6a00-0x20ff7f8fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 21 pages/cpu s47848 r8192 d29976 u86016 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3888132K/4126720K available (16192K kernel code, 3732K rwdata, 9356K rodata, 7616K init, 609K bss, 205820K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008844] Console: colour dummy device 80x25 <6>[ 0.013638] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024357] pid_max: default: 32768 minimum: 301 <6>[ 0.029312] LSM: Security Framework initializing <6>[ 0.034304] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042052] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051083] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.058657] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.065114] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.072676] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.079199] rcu: Hierarchical SRCU implementation. <6>[ 0.084303] rcu: Max phase no-delay instances is 1000. <6>[ 0.089976] Platform MSI: gic-its@6020000 domain created <6>[ 0.095676] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.103536] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.109750] EFI services will not be available. <6>[ 0.114688] smp: Bringing up secondary CPUs ... <6>[ 0.119797] Detected PIPT I-cache on CPU1 <6>[ 0.119847] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.119856] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.119880] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.119934] smp: Brought up 1 node, 2 CPUs <6>[ 0.150253] SMP: Total of 2 processors activated. <6>[ 0.155265] CPU features: detected: 32-bit EL0 Support <6>[ 0.160722] CPU features: detected: 32-bit EL1 Support <6>[ 0.166173] CPU features: detected: CRC32 instructions <6>[ 0.171656] CPU: All CPU(s) started at EL2 <6>[ 0.176061] alternatives: applying system-wide alternatives <6>[ 0.183025] devtmpfs: initialized <6>[ 0.189918] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.200041] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.207746] pinctrl core: initialized pinctrl subsystem <6>[ 0.213681] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.221326] SoC family: QorIQ LS1028A <6>[ 0.225279] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.230574] DMI not present or invalid. <6>[ 0.235123] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.241951] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.249446] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.257677] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.265967] audit: initializing netlink subsys (disabled) <5>[ 0.271793] audit: type=2000 audit(0.164:1): state=initialized audit_enabled=0 res=1 <6>[ 0.272378] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.279880] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.286305] cpuidle: using governor menu <6>[ 0.297495] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.304640] ASID allocator initialised with 65536 entries <6>[ 0.311215] Serial: AMBA PL011 UART driver <4>[ 0.325911] KASLR disabled due to lack of seed <6>[ 0.335505] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.342629] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.349223] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.356339] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.362928] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.370042] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.376631] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.383745] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.391275] ACPI: Interpreter disabled. <6>[ 0.396733] iommu: Default domain type: Translated <6>[ 0.401923] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.408647] SCSI subsystem initialized <6>[ 0.412903] usbcore: registered new interface driver usbfs <6>[ 0.418727] usbcore: registered new interface driver hub <6>[ 0.424367] usbcore: registered new device driver usb <6>[ 0.430018] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.437814] i2c i2c-0: IMX I2C adapter registered <6>[ 0.443019] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.450673] i2c i2c-1: IMX I2C adapter registered <6>[ 0.455786] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.463505] i2c i2c-2: IMX I2C adapter registered <6>[ 0.468940] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.474216] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.483716] PTP clock support registered <6>[ 0.488016] EDAC MC: Ver: 3.0.0 <6>[ 0.492302] FPGA manager framework <6>[ 0.496048] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.502861] vgaarb: loaded <6>[ 0.506027] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.512572] VFS: Disk quotas dquot_6.6.0 <6>[ 0.516818] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.524113] pnp: PnP ACPI: disabled <6>[ 0.531560] NET: Registered PF_INET protocol family <6>[ 0.536962] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.546716] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.555639] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.563735] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.572077] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.580441] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.587399] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.594471] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.602064] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.608329] RPC: Registered named UNIX socket transport module. <6>[ 0.614580] RPC: Registered udp transport module. <6>[ 0.619590] RPC: Registered tcp transport module. <6>[ 0.624600] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.631379] PCI: CLS 0 bytes, default 64 <6>[ 0.635697] Unpacking initramfs... <6>[ 0.639712] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 0.648517] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.654009] kvm [1]: GICv3: no GICV resource entry <6>[ 0.659117] kvm [1]: disabling GICv2 emulation <6>[ 0.663883] kvm [1]: GIC system register CPU interface enabled <6>[ 0.670083] kvm [1]: vgic interrupt IRQ9 <6>[ 0.674358] kvm [1]: Hyp mode initialized successfully <5>[ 0.680459] Initialise system trusted keyrings <6>[ 0.685358] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.695725] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.702322] NFS: Registering the id_resolver key type <5>[ 0.707720] Key type id_resolver registered <5>[ 0.712224] Key type id_legacy registered <6>[ 0.716607] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.723645] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.731527] 9p: Installing v9fs 9p2000 file system support <5>[ 0.767342] Key type asymmetric registered <5>[ 0.771746] Asymmetric key parser 'x509' registered <6>[ 0.776981] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.784720] io scheduler mq-deadline registered <6>[ 0.789559] io scheduler kyber registered <6>[ 0.800840] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.808986] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.818246] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.827428] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.836600] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.845773] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.854943] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.864114] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.873326] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.882499] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.889832] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.895390] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.902801] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.910642] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.918042] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.925871] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.933272] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.941111] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.948536] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.954917] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.965749] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.977017] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.988107] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.999676] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.005511] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.015821] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.026735] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.033111] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.043940] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.055199] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.066291] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.077844] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.083677] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.093979] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.104902] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.111286] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.122117] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.133404] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.139415] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.145800] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.156631] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.167914] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.173881] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.180261] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.191092] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.202382] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.208376] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.214743] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.225556] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.236803] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.247626] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.253621] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.259986] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.270805] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.282069] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.288784] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.295177] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.303193] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.311330] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 1.317619] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 1.324207] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.331886] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.340778] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.349718] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 1.355965] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 1.399953] Freeing initrd memory: 21676K <3>[ 2.364324] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.370787] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.377821] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.383625] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.390130] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.401042] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.407430] pci 0001:00:00.0: supports D1 D2 <6>[ 2.412004] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.419259] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.426214] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 2.431622] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.439294] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.448177] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.457088] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 2.463329] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 3.471681] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.478068] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.485100] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.490903] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.500216] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.511121] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.517501] pci 0002:00:00.0: supports D1 D2 <6>[ 3.522074] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.529248] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.536202] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 3.542260] EINJ: ACPI disabled. <6>[ 3.559210] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.567465] printk: console [ttyS0] disabled <6>[ 3.572088] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 3.581252] printk: console [ttyS0] enabled <6>[ 3.581252] printk: console [ttyS0] enabled <6>[ 3.590205] printk: bootconsole [ns16550a0] disabled <6>[ 3.590205] printk: bootconsole [ns16550a0] disabled <6>[ 3.601049] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 3.610494] SuperH (H)SCI(F) driver initialized <6>[ 3.615619] msm_serial: driver initialized <6>[ 3.620402] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 3.632071] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.638810] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.643707] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.649298] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.654889] arm-smmu 5000000.iommu: nested translation <5>[ 3.660395] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.667824] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.674644] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.681370] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.688095] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 3.695035] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 3.704324] loop: module loaded <4>[ 3.713294] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 3.723292] megasas: 07.719.03.00-rc1 <6>[ 3.729333] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 3.748891] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 3.766152] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 3.773269] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 3.778777] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 3.784392] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 3.791330] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 3.798260] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 3.804383] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 3.813676] tun: Universal TUN/TAP device driver, 1.6 <6>[ 3.819615] thunder_xcv, ver 1.0 <6>[ 3.823150] thunder_bgx, ver 1.0 <6>[ 3.826677] nicpf, ver 1.0 <6>[ 3.830219] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 3.836291] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 3.950044] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 3.957436] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 3.963802] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 4.074037] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 4.080847] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 4.087209] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 4.198040] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 4.204838] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 4.211461] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 4.322044] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.343442] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 4.349777] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.356712] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.365725] pps pps0: new PPS source ptp0 <6>[ 4.370507] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.378036] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.383666] hclge is initializing <6>[ 4.387263] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.392419] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.398477] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.403725] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.409956] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.415636] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.421509] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.428064] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.434502] sky2: driver version 1.30 <6>[ 4.439162] VFIO - User Level meta-driver version: 0.3 <6>[ 4.444985] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 4.451189] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 4.458881] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.464673] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.472749] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 4.482468] xhci-hcd xhci-hcd.0.auto: irq 99, io mem 0x03100000 <6>[ 4.488763] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.494535] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.502485] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.509617] hub 1-0:1.0: USB hub found <6>[ 4.513660] hub 1-0:1.0: 1 port detected <6>[ 4.518032] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.526668] hub 2-0:1.0: USB hub found <6>[ 4.530709] hub 2-0:1.0: 1 port detected <6>[ 4.535112] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.540892] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.548955] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 4.558672] xhci-hcd xhci-hcd.1.auto: irq 100, io mem 0x03110000 <6>[ 4.565047] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.570819] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.578770] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.585849] hub 3-0:1.0: USB hub found <6>[ 4.589890] hub 3-0:1.0: 1 port detected <6>[ 4.594247] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.602864] hub 4-0:1.0: USB hub found <6>[ 4.606904] hub 4-0:1.0: 1 port detected <6>[ 4.611632] usbcore: registered new interface driver usb-storage <6>[ 4.619884] i2c_dev: i2c /dev entries driver <6>[ 4.627842] sp805-wdt c000000.watchdog: registration successful <6>[ 4.634191] sp805-wdt c010000.watchdog: registration successful <6>[ 4.642010] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.650880] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.657369] sdhci: Copyright(c) Pierre Ossman <6>[ 4.662505] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.669448] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.675973] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 4.681953] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.682191] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 4.696035] usbcore: registered new interface driver usbhid <6>[ 4.701911] usbhid: USB HID core driver <6>[ 4.710350] NET: Registered PF_PACKET protocol family <6>[ 4.715771] 9pnet: Installing 9P2000 support <6>[ 4.718048] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <5>[ 4.720439] Key type dns_resolver registered <6>[ 4.727505] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.732299] registered taskstats version 1 <5>[ 4.743638] Loading compiled-in X.509 certificates <6>[ 4.752826] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 4.760765] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 4.766902] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.773225] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.779358] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 4.785471] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.791779] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.874053] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.881494] mmc0: new HS400 MMC card at address 0001 <6>[ 4.887270] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.893368] mmcblk0: p1 p2 <6>[ 4.896910] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.902042] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.903147] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.909616] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 0a:ad:f5:91:ba:78 <6>[ 4.914693] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 4.922783] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 72:5a:74:b6:d3:60 <6>[ 4.941479] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.999455] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.027987] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.097955] hub 3-1:1.0: USB hub found <6>[ 5.102167] hub 3-1:1.0: 7 ports detected <6>[ 8.098990] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 8.126073] Sending DHCP requests ., OK <6>[ 8.146349] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.127 <6>[ 8.154444] IP-Config: Complete: <6>[ 8.157953] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.127, mask=255.255.255.0, gw=172.16.0.254 <6>[ 8.168491] host=172.16.0.127, domain=lava.lan, nis-domain=(none) <6>[ 8.175340] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.175357] nameserver0=8.8.8.8 <6>[ 8.186203] clk: Disabling unused clocks <6>[ 8.190530] ALSA device list: <6>[ 8.193774] No soundcards found. <6>[ 8.201381] Freeing unused kernel memory: 7616K <6>[ 8.206338] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.272955] udevd[132]: starting version 3.2.9 <5>[ 9.290032] random: crng init done <27>[ 9.296563] udevd[132]: specified user 'tss' unknown <27>[ 9.301954] udevd[132]: specified group 'tss' unknown <30>[ 9.308324] udevd[133]: starting eudev-3.2.9 <27>[ 9.567903] udevd[142]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <4>[ 9.577592] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.597988] NET: Registered PF_INET6 protocol family <6>[ 9.598124] CAN device driver interface <28>[ 9.607514] udevd[142]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 9.627433] Segment Routing with IPv6 <6>[ 9.631424] In-situ OAM (IOAM) with IPv6 <6>[ 9.634435] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 9.643428] wm8904 2-001a: supply DCVDD not found, using dummy regulator <6>[ 9.654850] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 9.665481] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 9.679209] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 9.682215] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 9.689974] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 9.704027] fsl_ddr_edac acquired irq 112 for MC <6>[ 9.708954] fsl_ddr_edac MC err registered <6>[ 9.709535] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 9.714384] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 9.732293] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 9.739397] wm8904 2-001a: supply MICVDD not found, using dummy regulator <4>[ 9.742298] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 9.750803] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 9.754731] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 9.770620] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 9.778454] wm8904 2-001a: revision A <6>[ 9.790535] mscc_felix 0000:00:00.5: Adding to iommu group 13 <6>[ 9.799715] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 9.809076] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 9.817031] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 9.855539] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 9.868359] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 9.874035] rtc-rv8803 0-0032: registered as rtc0 <4>[ 9.880990] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 9.887418] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 9.963516] caam 8000000.crypto: Entropy delay = 3200 <6>[ 10.009662] mali-dp f080000.display: Adding to iommu group 14 <6>[ 10.023277] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 10.040382] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.043346] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 10.052839] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 10.053745] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 10.059885] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 10.076574] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 10.110397] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 10.116682] caam algorithms registered in /proc/crypto <6>[ 10.122929] caam 8000000.crypto: registering rng-caam <6>[ 10.128439] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 10.135616] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 10.141615] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 10.147627] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-501860/environment . /lava-501860/environment / # /lava-501860/bin/lava-test-runner /lava-501860/0 /lava-501860/bin/lava-test-runner /lava-501860/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 10.740778] d /lava-501860/0/tests/0_dmesg + cat uuid + UUID=501860_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.761355] <8>[ 10.782888] <8>[ 10.804220] + set +x <8>[ 10.813896] / #