Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.73 (255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 511172/tftp-deploy-fz3qvlid/kernel/Image tftp 0x82000000 511172/tftp-deploy-fz3qvlid/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.73; sending through gateway 172.16.0.254 Filename '511172/tftp-deploy-fz3qvlid/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 13.9 MiB/s done Bytes transferred = 58178048 (377ba00 hex) => tftp 0x90080000 511172/tftp-deploy-fz3qvlid/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 511172/tftp-deploy-fz3qvlid/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.73; sending through gateway 172.16.0.254 Filename '511172/tftp-deploy-fz3qvlid/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######## 14.5 MiB/s done Bytes transferred = 28742685 (1b6941d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 511172/tftp-deploy-fz3qvlid/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 511172/tftp-deploy-fz3qvlid/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.73; sending through gateway 172.16.0.254 Filename '511172/tftp-deploy-fz3qvlid/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *## 5.4 MiB/s done Bytes transferred = 28448 (6f20 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-04 20:51:47 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 28742621 Bytes = 27.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 0000000090009f1f WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.112-cip30 (KernelCI@build-j362210-arm64-gcc-12-defconfig-kselftest-f5nbr) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Mon Nov 4 20:34:35 UTC 2024 [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7d4640-0x20ff7d6fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 [ 0.000000] percpu: Embedded 32 pages/cpu s92704 r8192 d30176 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3916412K/4194304K available (23424K kernel code, 7150K rwdata, 11840K rodata, 14272K init, 11463K bss, 245124K reserved, 32768K cma-reserved) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 66663 entries in 261 pages <6>[ 0.000000] ftrace: allocated 261 pages with 3 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080380000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080310000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080320000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.009153] Console: colour dummy device 80x25 <4>[ 0.013943] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.022044] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026459] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030961] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035637] ... CLASSHASH_SIZE: 4096 <4>[ 0.040314] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.045079] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049843] ... CHAINHASH_SIZE: 32768 <4>[ 0.054608] memory used by lock dependency info: 6365 kB <4>[ 0.060338] memory used for stack traces: 4224 kB <4>[ 0.065453] per task-struct memory footprint: 1920 bytes <6>[ 0.071310] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.082055] pid_max: default: 32768 minimum: 301 <6>[ 0.087339] LSM: Security Framework initializing <6>[ 0.092360] landlock: Up and running. <6>[ 0.096384] LSM support for eBPF active <6>[ 0.100836] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.108596] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.123035] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.130653] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.137357] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.144971] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.151667] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.159278] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.165970] Running RCU-tasks wait API self tests <6>[ 0.276249] rcu: Hierarchical SRCU implementation. <6>[ 0.281392] rcu: Max phase no-delay instances is 1000. <6>[ 0.287024] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.300815] Platform MSI: gic-its@6020000 domain created <6>[ 0.306692] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.314662] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.320996] EFI services will not be available. <6>[ 0.326471] smp: Bringing up secondary CPUs ... <6>[ 0.333157] Detected PIPT I-cache on CPU1 <6>[ 0.333262] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.333273] GICv3: CPU1: using allocated LPI pending table @0x0000002080330000 <6>[ 0.333319] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.333731] smp: Brought up 1 node, 2 CPUs <6>[ 0.364185] SMP: Total of 2 processors activated. <6>[ 0.369223] CPU features: detected: 32-bit EL0 Support <6>[ 0.374745] CPU features: detected: 32-bit EL1 Support <6>[ 0.380242] CPU features: detected: CRC32 instructions <6>[ 0.385816] CPU: All CPU(s) started at EL2 <6>[ 0.390250] alternatives: applying system-wide alternatives <6>[ 0.400549] devtmpfs: initialized <6>[ 0.416907] Callback from call_rcu_tasks_rude() invoked. <6>[ 0.451773] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.461922] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.480731] pinctrl core: initialized pinctrl subsystem <6>[ 0.490501] Machine: Kontron KBox A-230-LS <6>[ 0.494923] SoC family: QorIQ LS1028A <6>[ 0.498884] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.507032] DMI not present or invalid. <6>[ 0.513234] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.523186] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.530955] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.539746] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.548267] audit: initializing netlink subsys (disabled) <5>[ 0.554515] audit: type=2000 audit(0.408:1): state=initialized audit_enabled=0 res=1 <6>[ 0.559468] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.562609] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.569258] cpuidle: using governor menu <6>[ 0.580463] Callback from call_rcu_tasks() invoked. <6>[ 0.581326] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.592905] ASID allocator initialised with 65536 entries <6>[ 0.606580] Serial: AMBA PL011 UART driver <4>[ 0.677544] KASLR disabled due to lack of seed <6>[ 0.743170] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.750454] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.757094] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.764227] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.770844] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.777975] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.784582] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.791712] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.806188] ACPI: Interpreter disabled. <6>[ 0.819524] iommu: Default domain type: Translated <6>[ 0.824751] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.833341] SCSI subsystem initialized <6>[ 0.839446] usbcore: registered new interface driver usbfs <6>[ 0.845541] usbcore: registered new interface driver hub <6>[ 0.851336] usbcore: registered new device driver usb <6>[ 0.858979] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.868714] i2c i2c-0: IMX I2C adapter registered <6>[ 0.875389] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.884183] i2c i2c-1: IMX I2C adapter registered <6>[ 0.890023] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.898412] i2c i2c-2: IMX I2C adapter registered <6>[ 0.905481] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.910833] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.920450] PTP clock support registered <6>[ 0.925311] EDAC MC: Ver: 3.0.0 <6>[ 0.934359] FPGA manager framework <6>[ 0.938781] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.947981] NET: Registered PF_ATMPVC protocol family <6>[ 0.953386] NET: Registered PF_ATMSVC protocol family <6>[ 0.959892] vgaarb: loaded <6>[ 0.964086] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.973617] VFS: Disk quotas dquot_6.6.0 <6>[ 0.978045] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.986548] pnp: PnP ACPI: disabled <6>[ 1.020973] NET: Registered PF_INET protocol family <6>[ 1.026515] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.038057] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 147456 bytes, linear) <6>[ 1.047553] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.055754] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.064287] TCP bind hash table entries: 32768 (order: 10, 4718592 bytes, vmalloc hugepage) <6>[ 1.082183] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.090062] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.098786] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.106715] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.115560] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.123420] RPC: Registered named UNIX socket transport module. <6>[ 1.129711] RPC: Registered udp transport module. <6>[ 1.134750] RPC: Registered tcp transport module. <6>[ 1.139780] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.146611] NET: Registered PF_XDP protocol family <6>[ 1.151748] PCI: CLS 0 bytes, default 64 <6>[ 1.157107] Unpacking initramfs... <6>[ 1.169577] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.184847] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.205739] kvm [1]: GICv3: no GICV resource entry <6>[ 1.220092] kvm [1]: disabling GICv2 emulation <6>[ 1.224902] kvm [1]: GIC system register CPU interface enabled <6>[ 1.244260] kvm [1]: vgic interrupt IRQ9 <6>[ 1.256144] kvm [1]: Hyp mode initialized successfully <5>[ 1.277927] Initialise system trusted keyrings <6>[ 1.296377] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.430311] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.441932] NFS: Registering the id_resolver key type <5>[ 1.447525] Key type id_resolver registered <5>[ 1.452082] Key type id_legacy registered <6>[ 1.457065] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.464188] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.473592] 9p: Installing v9fs 9p2000 file system support <6>[ 1.511544] NET: Registered PF_ALG protocol family <5>[ 1.516811] Key type asymmetric registered <5>[ 1.521278] Asymmetric key parser 'x509' registered <6>[ 1.526779] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.534602] io scheduler mq-deadline registered <6>[ 1.539468] io scheduler kyber registered <4>[ 1.545075] test_firmware: interface ready <6>[ 1.645082] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.660247] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 1.676226] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 1.696214] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 1.712217] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 1.732217] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 1.752216] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 1.768205] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 1.788378] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.808904] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.824274] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.829874] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 1.852233] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.868226] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 1.884190] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.900208] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 1.916204] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.932189] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.948314] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.964363] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.980423] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.004145] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.028150] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.048253] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 2.054228] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.088180] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.105449] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 2.118917] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.129875] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.141237] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.152417] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.164141] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 2.170032] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.180350] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.192318] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 2.198827] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.209673] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.221045] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 2.227918] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 2.234454] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.245300] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.256686] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 2.263658] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 2.270406] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.281339] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.292788] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 2.300018] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 2.306540] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.317402] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.328683] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.339613] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 2.346610] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 2.353113] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.363960] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.375329] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 2.383110] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 2.389784] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 2.398967] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 2.408271] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 2.415708] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 2.425381] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 2.433180] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 2.442218] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 2.451244] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 2.457517] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.272963] Freeing initrd memory: 28064K <3>[ 3.412242] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 3.419199] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.426278] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.432114] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.438648] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.449671] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.456274] pci 0001:00:00.0: supports D1 D2 <6>[ 3.460872] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.469530] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.476531] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.482584] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.490367] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.499324] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.508312] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 3.514577] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 4.523186] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 4.530039] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 4.537106] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 4.542940] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 4.552282] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 4.563267] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 4.569843] pci 0002:00:00.0: supports D1 D2 <6>[ 4.574441] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 4.582987] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 4.589986] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 4.599950] EINJ: ACPI disabled. <6>[ 4.686791] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 4.705953] printk: console [ttyS0] disabled <6>[ 4.711027] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.720412] printk: console [ttyS0] enabled <6>[ 4.720412] printk: console [ttyS0] enabled <6>[ 4.729424] printk: bootconsole [ns16550a0] disabled <6>[ 4.729424] printk: bootconsole [ns16550a0] disabled <6>[ 4.743163] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.754434] SuperH (H)SCI(F) driver initialized <6>[ 4.760974] msm_serial: driver initialized <6>[ 4.767713] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 4.797770] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.804543] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.809463] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.815082] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.820697] arm-smmu 5000000.iommu: nested translation <5>[ 4.826238] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.833707] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.840591] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.847343] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.854093] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.863416] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 4.899816] loop: module loaded <6>[ 4.905952] lkdtm: No crash points registered, enable through debugfs <4>[ 4.945943] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 4.959475] megasas: 07.719.03.00-rc1 <6>[ 4.969180] ahci-qoriq 3200000.sata: Adding to iommu group 0 <4>[ 4.976243] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator <4>[ 4.984930] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator <4>[ 4.993016] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator <6>[ 5.001797] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode <6>[ 5.011090] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst <6>[ 5.024506] scsi host0: ahci-qoriq <6>[ 5.030062] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 96 <6>[ 5.052055] spi-nor spi0.0: w25q32dw (4096 Kbytes) <5>[ 5.085053] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 5.092220] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 5.097854] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 5.110489] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 5.122923] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 5.135551] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 5.147131] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 5.186946] thunder_xcv, ver 1.0 <6>[ 5.190736] thunder_bgx, ver 1.0 <6>[ 5.194525] nicpf, ver 1.0 <6>[ 5.200987] fsl_enetc 0000:00:00.0: Adding to iommu group 1 <6>[ 5.208395] fsl_enetc 0000:00:00.1: Adding to iommu group 2 <6>[ 5.215613] fsl_enetc 0000:00:00.2: Adding to iommu group 3 <6>[ 5.223047] fsl_enetc 0000:00:00.6: Adding to iommu group 4 <6>[ 5.231523] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 5 <6>[ 5.344132] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 5.350794] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 5.408836] mdio_bus 0000:00:00.3:04: Fixed dependency cycle(s) with /soc/pcie@1f0000000/mdio@0,3/ethernet-phy@4/vddio-regulator <5>[ 5.448576] bcm_phy_lib: module verification failed: signature and/or required key missing - tainting kernel <6>[ 5.565737] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 6 <6>[ 5.572726] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 5.580823] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 5.590606] pps pps0: new PPS source ptp0 <6>[ 5.597872] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 5.605430] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 5.611425] hclge is initializing <6>[ 5.615142] e1000: Intel(R) PRO/1000 Network Driver <6>[ 5.620323] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 5.626648] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 5.631916] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.638406] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 5.644109] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.650180] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 5.656758] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 5.664406] sky2: driver version 1.30 <6>[ 5.672720] VFIO - User Level meta-driver version: 0.3 <6>[ 5.680784] dwc3 3100000.usb: Adding to iommu group 7 <6>[ 5.689347] dwc3 3110000.usb: Adding to iommu group 8 <6>[ 5.710459] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.716556] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 5.725450] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 5.735327] xhci-hcd xhci-hcd.0.auto: irq 101, io mem 0x03110000 <6>[ 5.742737] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.748567] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 5.756571] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.766961] hub 1-0:1.0: USB hub found <6>[ 5.771354] hub 1-0:1.0: 1 port detected <6>[ 5.777885] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.788985] hub 2-0:1.0: USB hub found <6>[ 5.793169] hub 2-0:1.0: 1 port detected <6>[ 5.800631] usbcore: registered new interface driver usb-storage <6>[ 5.818815] i2c_dev: i2c /dev entries driver <6>[ 5.843778] sp805-wdt c000000.watchdog: registration successful <6>[ 5.851191] sp805-wdt c010000.watchdog: registration successful <6>[ 5.867228] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 5.883393] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.889936] sdhci: Copyright(c) Pierre Ossman <6>[ 5.897163] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.907682] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.916987] sdhci-esdhc 2140000.mmc: Adding to iommu group 9 <6>[ 5.924218] sdhci-esdhc 2150000.mmc: Adding to iommu group 10 <6>[ 5.930556] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.947928] usbcore: registered new interface driver usbhid <6>[ 5.953831] usbhid: USB HID core driver <6>[ 5.964293] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 5.971738] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 5.984829] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.992640] IPv4 over IPsec tunneling driver <6>[ 6.002796] NET: Registered PF_INET6 protocol family <6>[ 6.014643] Segment Routing with IPv6 <6>[ 6.018987] In-situ OAM (IOAM) with IPv6 <6>[ 6.026137] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.036171] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 6.036884] NET: Registered PF_PACKET protocol family <6>[ 6.049600] 9pnet: Installing 9P2000 support <5>[ 6.054468] Key type dns_resolver registered <6>[ 6.059061] mpls_gso: MPLS GSO support <6>[ 6.071363] registered taskstats version 1 <6>[ 6.073198] mmc0: new HS400 MMC card at address 0001 <5>[ 6.075951] Loading compiled-in X.509 certificates <6>[ 6.084946] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 6.101560] mmcblk0: p1 p2 p3 <6>[ 6.109552] mmcblk0boot0: mmc0:0001 S0J58X 31.5 MiB <6>[ 6.124047] mmcblk0boot1: mmc0:0001 S0J58X 31.5 MiB <6>[ 6.137023] mmcblk0rpmb: mmc0:0001 S0J58X 4.00 MiB, chardev (511:0) <5>[ 6.143465] Loaded X.509 cert 'Build time autogenerated kernel key: 53425c829e8e0fa9c8d3c0af7abef4e871897764' <6>[ 6.154646] ima: No TPM chip found, activating TPM-bypass! <6>[ 6.160522] ima: Allocated hash algorithm: sha1 <6>[ 6.165536] ima: No architecture policies found <6>[ 6.214288] fsl-edma 22c0000.dma-controller: Adding to iommu group 11 <6>[ 6.233407] pcieport 0001:00:00.0: Adding to iommu group 12 <6>[ 6.241155] pcieport 0001:00:00.0: PME: Signaling with IRQ 105 <6>[ 6.244560] hub 1-1:1.0: USB hub found <6>[ 6.248516] pcieport 0001:00:00.0: AER: enabled with IRQ 105 <6>[ 6.251593] hub 1-1:1.0: 7 ports detected <6>[ 6.258870] pcieport 0002:00:00.0: Adding to iommu group 13 <6>[ 6.269418] pcieport 0002:00:00.0: PME: Signaling with IRQ 106 <6>[ 6.276706] pcieport 0002:00:00.0: AER: enabled with IRQ 106 <6>[ 6.388229] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 6.399325] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 0e:7d:ee:fc:af:82 <6>[ 6.408190] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using de:76:ad:f6:f2:5d <6>[ 6.532508] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 6.543679] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using 06:64:a7:88:d9:f6 <6>[ 6.552548] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using 2e:b8:db:45:ba:81 <6>[ 6.600154] usb 1-1.6: new full-speed USB device number 3 using xhci-hcd <6>[ 6.672286] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 6.680743] fsl_enetc 0000:00:00.2: no MAC address specified for SI0, using 4a:6d:5c:d2:03:eb <3>[ 6.769734] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <6>[ 6.804493] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 6.812970] fsl_enetc 0000:00:00.6: no MAC address specified for SI0, using 56:be:0a:e2:9d:b6 <6>[ 6.843698] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 6.923474] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 7.013098] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 7.094402] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.3:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 7.151110] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 7.207269] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 7.215445] fsl_enetc 0000:00:00.2 eth2: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 7.261538] fsl_enetc 0000:00:00.6 eth3: configuring for fixed/internal link mode <6>[ 7.269462] fsl_enetc 0000:00:00.6 eth3: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 7.270904] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready <6>[ 7.285189] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready <5>[ 7.316173] Sending DHCP requests .. <6>[ 10.078331] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 10.078462] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <4>[ 14.700281] ., OK <6>[ 14.705191] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.73 <6>[ 14.713323] IP-Config: Complete: <6>[ 14.716961] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.73, mask=255.255.255.0, gw=172.16.0.254 <6>[ 14.727506] host=172.16.0.73, domain=lava.lan, nis-domain=(none) <6>[ 14.734368] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 14.734407] nameserver0=8.8.8.8 <6>[ 14.815188] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 14.861224] fsl_enetc 0000:00:00.6 eth3: Link is Down <6>[ 14.906511] clk: Disabling unused clocks <6>[ 14.910999] ALSA device list: <6>[ 14.914329] No soundcards found. <6>[ 14.966001] Freeing unused kernel memory: 14272K <6>[ 14.971106] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.326564] udevd[149]: starting version 3.2.9 <5>[ 16.304237] random: crng init done <27>[ 16.318006] udevd[149]: specified user 'tss' unknown <27>[ 16.323552] udevd[149]: specified group 'tss' unknown <30>[ 16.335451] udevd[150]: starting eudev-3.2.9 <6>[ 17.777545] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 17.790199] fsl_ddr_edac acquired irq 121 for MC <6>[ 17.798065] fsl_ddr_edac MC err registered <6>[ 17.833607] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <6>[ 17.893084] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <4>[ 17.921103] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 17.929010] fsl_enetc 0000:00:00.6 enp0s0f6: renamed from eth3 <27>[ 17.957467] udevd[154]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <4>[ 17.980704] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 17.991641] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 18.008287] rtc-rv8803 0-0032: Voltage low, data loss detected. <28>[ 18.012832] udevd[154]: could not rename interface '8' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 18.026314] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 18.026540] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 18.044626] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 18.052629] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 18.056984] rtc-rv8803 0-0032: registered as rtc0 <4>[ 18.072626] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 18.084271] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 18.099791] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 18.110914] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 18.124763] mscc_felix 0000:00:00.5: Adding to iommu group 14 <4>[ 18.138310] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 18.154015] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 18.157979] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <4>[ 18.200950] mscc_felix 0000:00:00.5: Failed to find a tagging driver for protocol ocelot-8021q, using default <6>[ 18.233495] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <4>[ 18.260788] mscc_felix 0000:00:00.5: Failed to find a tagging driver for protocol ocelot-8021q, using default <6>[ 18.310144] CAN device driver interface <6>[ 18.438382] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 18.525715] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <6>[ 18.538233] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <6>[ 18.549713] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <6>[ 18.556954] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <6>[ 18.702264] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 18.710712] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 18.726041] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 18.736737] mali-dp f080000.display: Adding to iommu group 15 <6>[ 18.737472] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 18.780392] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 18.808380] mscc_felix 0000:00:00.5: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 18.875718] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.902343] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 18.911192] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 18.923709] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 18.983659] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Broadcom BCM54140] (irq=POLL) <6>[ 19.081710] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Broadcom BCM54140] (irq=POLL) <6>[ 19.179514] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Broadcom BCM54140] (irq=POLL) <6>[ 19.209681] device enp0s0f2 entered promiscuous mode <6>[ 19.224830] caam_jr 8010000.jr: Adding to iommu group 16 <6>[ 19.237125] device enp0s0f6 entered promiscuous mode <6>[ 19.243939] DSA: tree 0 setup <6>[ 19.247518] caam algorithms registered in /proc/crypto <6>[ 19.290856] caam 8000000.crypto: registering rng-caam <6>[ 19.302762] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.311952] caam_jr 8020000.jr: Adding to iommu group 17 <6>[ 19.320619] caam_jr 8030000.jr: Adding to iommu group 18 <6>[ 19.328914] caam_jr 8040000.jr: Adding to iommu group 19 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-511172/environment . /lava-511172/environment / # /lava-511172/bin/lava-test-runner /lava-511172/0 /lava-511172/bin/lava-test-runner /lava-511172/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-511172/0/tests/0_dmesg + cat uuid + UUID=511172_1.5.<8>[ 20.381098] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 20.480203] <8>[ 20.579256] <8>[ 20.685333] + set +x <8>[ 20.707877] / # <0�