Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete..... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.111 (1257 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 350887/tftp-deploy-aqon2v0q/kernel/Image tftp 0x82000000 350887/tftp-deploy-aqon2v0q/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.111; sending through gateway 172.16.0.254 Filename '350887/tftp-deploy-aqon2v0q/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 15.6 MiB/s done Bytes transferred = 52455936 (3206a00 hex) => tftp 0x90080000 350887/tftp-deploy-aqon2v0q/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 350887/tftp-deploy-aqon2v0q/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.111; sending through gateway 172.16.0.254 Filename '350887/tftp-deploy-aqon2v0q/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 15.1 MiB/s done Bytes transferred = 26906463 (19a8f5f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 350887/tftp-deploy-aqon2v0q/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 350887/tftp-deploy-aqon2v0q/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.111; sending through gateway 172.16.0.254 Filename '350887/tftp-deploy-aqon2v0q/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *## 3.9 MiB/s done Bytes transferred = 28448 (6f20 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2023-06-05 22:37:46 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26906399 Bytes = 25.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 0000000090009f1f WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.31 (KernelCI@build-j1612516-arm64-gcc-10-defconfig-kselftest-dqqsp) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Mon Jun 5 22:24:33 UTC 2023 [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7d3640-0x20ff7d5fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 [ 0.000000] percpu: Embedded 31 pages/cpu s89696 r8192 d29088 u126976 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3923904K/4194304K available (22144K kernel code, 5850K rwdata, 11096K rodata, 11968K init, 11400K bss, 237632K reserved, 32768K cma-reserved) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 66730 entries in 261 pages <6>[ 0.000000] ftrace: allocated 261 pages with 3 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080380000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080310000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080320000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.009122] Console: colour dummy device 80x25 <4>[ 0.013907] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.022009] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026425] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030927] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035605] ... CLASSHASH_SIZE: 4096 <4>[ 0.040283] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.045048] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049813] ... CHAINHASH_SIZE: 32768 <4>[ 0.054578] memory used by lock dependency info: 6365 kB <4>[ 0.060309] memory used for stack traces: 4224 kB <4>[ 0.065425] per task-struct memory footprint: 1920 bytes <6>[ 0.071285] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.082030] pid_max: default: 32768 minimum: 301 <6>[ 0.087340] LSM: Security Framework initializing <6>[ 0.092363] landlock: Up and running. <6>[ 0.096387] LSM support for eBPF active <6>[ 0.100839] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.108601] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.123106] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.130743] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.137453] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.144185] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.150914] Running RCU-tasks wait API self tests <6>[ 0.261170] rcu: Hierarchical SRCU implementation. <6>[ 0.266312] rcu: Max phase no-delay instances is 1000. <6>[ 0.271941] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.285929] Platform MSI: gic-its@6020000 domain created <6>[ 0.291803] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.299783] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.306111] EFI services will not be available. <6>[ 0.311585] smp: Bringing up secondary CPUs ... <6>[ 0.318295] Detected PIPT I-cache on CPU1 <6>[ 0.318370] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.318381] GICv3: CPU1: using allocated LPI pending table @0x0000002080330000 <6>[ 0.318424] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.318837] smp: Brought up 1 node, 2 CPUs <6>[ 0.349273] SMP: Total of 2 processors activated. <6>[ 0.354310] CPU features: detected: 32-bit EL0 Support <6>[ 0.359831] CPU features: detected: 32-bit EL1 Support <6>[ 0.365319] CPU features: detected: CRC32 instructions <6>[ 0.370890] CPU: All CPU(s) started at EL2 <6>[ 0.375321] alternatives: applying system-wide alternatives <6>[ 0.384455] devtmpfs: initialized <6>[ 0.404833] Callback from call_rcu_tasks_rude() invoked. <6>[ 0.436694] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.446853] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.461247] pinctrl core: initialized pinctrl subsystem <6>[ 0.470975] Machine: Kontron KBox A-230-LS <6>[ 0.475394] SoC family: QorIQ LS1028A <6>[ 0.479355] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.487512] DMI not present or invalid. <6>[ 0.493700] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.503571] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.511271] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.519975] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.528491] audit: initializing netlink subsys (disabled) <5>[ 0.534718] audit: type=2000 audit(0.392:1): state=initialized audit_enabled=0 res=1 <6>[ 0.539644] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.542812] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.549462] cpuidle: using governor menu <6>[ 0.561500] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.568747] Callback from call_rcu_tasks() invoked. <6>[ 0.568787] ASID allocator initialised with 65536 entries <6>[ 0.587591] Serial: AMBA PL011 UART driver <4>[ 0.656547] KASLR disabled due to lack of seed <6>[ 0.722008] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.729208] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.735924] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.743059] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.749674] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.756806] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.763411] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.770540] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.785036] ACPI: Interpreter disabled. <6>[ 0.797935] iommu: Default domain type: Translated <6>[ 0.803157] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.811787] SCSI subsystem initialized <6>[ 0.817872] usbcore: registered new interface driver usbfs <6>[ 0.823959] usbcore: registered new interface driver hub <6>[ 0.829751] usbcore: registered new device driver usb <6>[ 0.837400] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.847130] i2c i2c-0: IMX I2C adapter registered <6>[ 0.853821] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.862773] i2c i2c-1: IMX I2C adapter registered <6>[ 0.868593] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.876994] i2c i2c-2: IMX I2C adapter registered <6>[ 0.884048] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.889399] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.899007] PTP clock support registered <6>[ 0.903778] EDAC MC: Ver: 3.0.0 <6>[ 0.913035] FPGA manager framework <6>[ 0.917463] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.926689] NET: Registered PF_ATMPVC protocol family <6>[ 0.932080] NET: Registered PF_ATMSVC protocol family <6>[ 0.938608] vgaarb: loaded <6>[ 0.942774] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.951927] VFS: Disk quotas dquot_6.6.0 <6>[ 0.956348] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.964825] pnp: PnP ACPI: disabled <6>[ 0.999247] NET: Registered PF_INET protocol family <6>[ 1.004798] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.016326] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 147456 bytes, linear) <6>[ 1.025805] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.034005] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.042536] TCP bind hash table entries: 32768 (order: 10, 4718592 bytes, vmalloc hugepage) <6>[ 1.060379] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.068272] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.077003] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.084911] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.093586] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.101445] RPC: Registered named UNIX socket transport module. <6>[ 1.107774] RPC: Registered udp transport module. <6>[ 1.112805] RPC: Registered tcp transport module. <6>[ 1.117832] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.124662] NET: Registered PF_XDP protocol family <6>[ 1.129796] PCI: CLS 0 bytes, default 64 <6>[ 1.135242] Unpacking initramfs... <6>[ 1.146894] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.163693] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.184686] kvm [1]: GICv3: no GICV resource entry <6>[ 1.198786] kvm [1]: disabling GICv2 emulation <6>[ 1.203594] kvm [1]: GIC system register CPU interface enabled <6>[ 1.218943] kvm [1]: vgic interrupt IRQ9 <6>[ 1.230858] kvm [1]: Hyp mode initialized successfully <5>[ 1.252512] Initialise system trusted keyrings <6>[ 1.271086] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.441193] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.452827] NFS: Registering the id_resolver key type <5>[ 1.458388] Key type id_resolver registered <5>[ 1.462946] Key type id_legacy registered <6>[ 1.467926] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.475071] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.484474] 9p: Installing v9fs 9p2000 file system support <6>[ 1.522132] NET: Registered PF_ALG protocol family <5>[ 1.527391] Key type asymmetric registered <5>[ 1.531848] Asymmetric key parser 'x509' registered <6>[ 1.537370] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.545196] io scheduler mq-deadline registered <6>[ 1.550068] io scheduler kyber registered <4>[ 1.555709] test_firmware: interface ready <6>[ 1.650582] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.674973] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 1.691113] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 1.714999] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 1.730992] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 1.740436] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 1.749687] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 1.758967] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 1.768473] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.778462] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.785884] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.791520] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 1.799018] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.806946] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 1.814418] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.822328] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 1.829832] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.846813] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.862973] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.869579] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.894820] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.914844] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.938832] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.962912] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.968892] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.994809] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.006927] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 2.013519] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.024431] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.035786] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.046993] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.058711] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 2.064655] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.075024] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.087071] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 2.093574] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.104448] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.131001] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 2.143960] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 2.155078] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.165958] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.177331] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 2.184343] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 2.190861] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.201707] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.213076] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 2.219963] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 2.226466] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.237311] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.248608] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.259534] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 2.266515] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 2.273275] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.284135] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.295506] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 2.303313] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 2.310005] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 2.319190] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 2.328301] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 2.335804] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 2.345094] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 2.352970] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 2.362009] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 2.371026] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 2.377305] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.247486] Freeing initrd memory: 26268K <3>[ 3.342842] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 3.349795] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.356875] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.362712] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.369248] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.380270] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.386866] pci 0001:00:00.0: supports D1 D2 <6>[ 3.391463] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.400116] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.407101] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.413079] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.420875] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.429831] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.438837] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 3.445101] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 4.453702] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 4.460534] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 4.467601] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 4.473435] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 4.482778] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 4.493760] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 4.500331] pci 0002:00:00.0: supports D1 D2 <6>[ 4.504927] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 4.513454] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 4.520453] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 4.530254] EINJ: ACPI disabled. <6>[ 4.615246] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 4.634274] printk: console [ttyS0] disabled <6>[ 4.639330] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.648704] printk: console [ttyS0] enabled <6>[ 4.648704] printk: console [ttyS0] enabled <6>[ 4.657738] printk: bootconsole [ns16550a0] disabled <6>[ 4.657738] printk: bootconsole [ns16550a0] disabled <6>[ 4.671569] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.682894] SuperH (H)SCI(F) driver initialized <6>[ 4.689347] msm_serial: driver initialized <6>[ 4.696185] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 4.725916] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.732690] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.737609] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.743224] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.748838] arm-smmu 5000000.iommu: nested translation <5>[ 4.754378] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.761848] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.768708] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.775470] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.782220] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.791663] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 4.827938] loop: module loaded <6>[ 4.833943] lkdtm: No crash points registered, enable through debugfs <4>[ 4.873266] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 4.886805] megasas: 07.719.03.00-rc1 <6>[ 4.896432] ahci-qoriq 3200000.sata: Adding to iommu group 0 <4>[ 4.903485] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator <4>[ 4.912165] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator <4>[ 4.920215] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator <6>[ 4.929002] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode <6>[ 4.938294] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst <6>[ 4.951803] scsi host0: ahci-qoriq <6>[ 4.957342] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 96 <6>[ 4.979585] spi-nor spi0.0: w25q32dw (4096 Kbytes) <5>[ 5.012219] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 5.019388] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 5.025182] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 5.037808] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 5.050210] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 5.062716] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 5.074251] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 5.114199] thunder_xcv, ver 1.0 <6>[ 5.117993] thunder_bgx, ver 1.0 <6>[ 5.121756] nicpf, ver 1.0 <6>[ 5.128189] fsl_enetc 0000:00:00.0: Adding to iommu group 1 <6>[ 5.135600] fsl_enetc 0000:00:00.1: Adding to iommu group 2 <6>[ 5.143116] fsl_enetc 0000:00:00.2: Adding to iommu group 3 <6>[ 5.150312] fsl_enetc 0000:00:00.6: Adding to iommu group 4 <6>[ 5.158832] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 5 <6>[ 5.270828] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 5.281477] ata1: SATA link down (SStatus 0 SControl 300) <5>[ 5.361460] bcm_phy_lib: module verification failed: signature and/or required key missing - tainting kernel <6>[ 5.473676] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 6 <6>[ 5.480665] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 5.488737] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 5.498524] pps pps0: new PPS source ptp0 <6>[ 5.505490] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 5.513301] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 5.519320] hclge is initializing <6>[ 5.523046] e1000: Intel(R) PRO/1000 Network Driver <6>[ 5.528223] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 5.534539] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 5.539816] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.546314] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 5.552014] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.558083] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 5.564658] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 5.572270] sky2: driver version 1.30 <6>[ 5.580448] VFIO - User Level meta-driver version: 0.3 <6>[ 5.588445] dwc3 3100000.usb: Adding to iommu group 7 <6>[ 5.599601] dwc3 3110000.usb: Adding to iommu group 8 <6>[ 5.618990] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.625076] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 5.633994] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 5.643877] xhci-hcd xhci-hcd.0.auto: irq 101, io mem 0x03110000 <6>[ 5.651309] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.657139] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 5.665143] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.675673] hub 1-0:1.0: USB hub found <6>[ 5.679971] hub 1-0:1.0: 1 port detected <6>[ 5.686431] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.697473] hub 2-0:1.0: USB hub found <6>[ 5.701662] hub 2-0:1.0: 1 port detected <6>[ 5.709140] usbcore: registered new interface driver usb-storage <6>[ 5.726832] i2c_dev: i2c /dev entries driver <6>[ 5.751304] sp805-wdt c000000.watchdog: registration successful <6>[ 5.758702] sp805-wdt c010000.watchdog: registration successful <6>[ 5.774375] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 5.787567] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.794075] sdhci: Copyright(c) Pierre Ossman <6>[ 5.801232] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.811349] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.820920] sdhci-esdhc 2140000.mmc: Adding to iommu group 9 <6>[ 5.827047] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.827686] sdhci-esdhc 2150000.mmc: Adding to iommu group 10 <6>[ 5.852742] usbcore: registered new interface driver usbhid <6>[ 5.858646] usbhid: USB HID core driver <6>[ 5.870957] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 5.878466] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 5.887977] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.895863] IPv4 over IPsec tunneling driver <6>[ 5.907044] NET: Registered PF_INET6 protocol family <6>[ 5.918469] Segment Routing with IPv6 <6>[ 5.922597] In-situ OAM (IOAM) with IPv6 <6>[ 5.929450] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.939849] NET: Registered PF_PACKET protocol family <6>[ 5.946045] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 5.960035] 8021q: 802.1Q VLAN Support v1.8 <6>[ 5.962830] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 5.965350] 9pnet: Installing 9P2000 support <5>[ 5.976487] Key type dns_resolver registered <6>[ 5.981170] mpls_gso: MPLS GSO support <6>[ 5.991705] registered taskstats version 1 <5>[ 5.996279] Loading compiled-in X.509 certificates <6>[ 6.012709] mmc0: new HS400 MMC card at address 0001 <6>[ 6.022323] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 6.037226] mmcblk0: p1 p2 p3 <6>[ 6.045223] mmcblk0boot0: mmc0:0001 S0J58X 31.5 MiB <5>[ 6.059256] Loaded X.509 cert 'Build time autogenerated kernel key: df1aaae2d160521060c3139935f3f6bef3cf7f1c' <6>[ 6.059941] mmcblk0boot1: mmc0:0001 S0J58X 31.5 MiB <6>[ 6.070581] ima: No TPM chip found, activating TPM-bypass! <6>[ 6.080895] ima: Allocated hash algorithm: sha1 <6>[ 6.085294] mmcblk0rpmb: mmc0:0001 S0J58X 4.00 MiB, chardev (511:0) <6>[ 6.085987] ima: No architecture policies found <6>[ 6.139904] fsl-edma 22c0000.dma-controller: Adding to iommu group 11 <6>[ 6.159084] pcieport 0001:00:00.0: Adding to iommu group 12 <6>[ 6.166626] pcieport 0001:00:00.0: PME: Signaling with IRQ 105 <6>[ 6.173926] pcieport 0001:00:00.0: AER: enabled with IRQ 105 <6>[ 6.181265] pcieport 0002:00:00.0: Adding to iommu group 13 <6>[ 6.188311] hub 1-1:1.0: USB hub found <6>[ 6.188646] pcieport 0002:00:00.0: PME: Signaling with IRQ 106 <6>[ 6.198639] hub 1-1:1.0: 7 ports detected <6>[ 6.199784] pcieport 0002:00:00.0: AER: enabled with IRQ 106 <6>[ 6.315056] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 6.326150] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 72:50:5b:18:0c:be <6>[ 6.335012] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 66:4f:c2:be:a0:53 <6>[ 6.458832] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 6.470272] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using ee:64:19:fd:5a:58 <6>[ 6.479141] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using 56:29:1e:5f:9e:34 <6>[ 6.547135] usb 1-1.6: new full-speed USB device number 3 using xhci-hcd <6>[ 6.599054] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 6.607497] fsl_enetc 0000:00:00.2: no MAC address specified for SI0, using d6:8c:ae:63:b0:22 <3>[ 6.710352] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <6>[ 6.731079] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 6.739545] fsl_enetc 0000:00:00.6: no MAC address specified for SI0, using 1e:9b:ab:e8:3c:98 <6>[ 6.769419] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 6.786289] 8021q: adding VLAN 0 to HW filter on device bond0 <6>[ 6.858498] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 6.958836] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 7.018450] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.3:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 7.117614] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 7.178987] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 7.186902] fsl_enetc 0000:00:00.2 eth2: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 7.237236] fsl_enetc 0000:00:00.6 eth3: configuring for fixed/internal link mode <6>[ 7.245131] fsl_enetc 0000:00:00.6 eth3: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 7.274863] Sending DHCP requests .. <6>[ 10.045122] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 10.057561] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <4>[ 13.470968] ., OK <6>[ 13.489894] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.111 <6>[ 13.498174] IP-Config: Complete: <6>[ 13.501819] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.111, mask=255.255.255.0, gw=172.16.0.254 <6>[ 13.512451] host=172.16.0.111, domain=lava.lan, nis-domain=(none) <6>[ 13.519401] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 13.519438] nameserver0=8.8.8.8 <6>[ 13.613631] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 13.663856] fsl_enetc 0000:00:00.6 eth3: Link is Down <6>[ 13.713352] ALSA device list: <6>[ 13.716722] No soundcards found. <6>[ 13.768770] Freeing unused kernel memory: 11968K <6>[ 13.774043] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.125914] udevd[149]: starting version 3.2.9 <5>[ 15.114954] random: crng init done <27>[ 15.128389] udevd[149]: specified user 'tss' unknown <27>[ 15.133920] udevd[149]: specified group 'tss' unknown <30>[ 15.145592] udevd[150]: starting eudev-3.2.9 <6>[ 16.927175] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <27>[ 16.997318] udevd[158]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 17.007602] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <6>[ 17.014364] fsl_ddr_edac acquired irq 121 for MC <6>[ 17.038834] fsl_ddr_edac MC err registered <6>[ 17.063999] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <28>[ 17.092007] udevd[158]: could not rename interface '8' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 17.115549] fsl_enetc 0000:00:00.6 enp0s0f6: renamed from eth3 <6>[ 17.279613] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 17.335739] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <4>[ 17.385366] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 17.395829] mscc_felix 0000:00:00.5: Failed to find a tagging driver for protocol ocelot-8021q, using default <4>[ 17.426858] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 17.454872] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 17.462070] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 17.503237] mscc_felix 0000:00:00.5: Failed to find a tagging driver for protocol ocelot-8021q, using default <4>[ 17.523429] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 17.570981] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 17.580011] rtc-rv8803 0-0032: registered as rtc0 <6>[ 17.623242] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 17.666283] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 17.673379] at24 2-0050: supply vcc not found, using dummy regulator <3>[ 17.678065] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 17.722228] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <6>[ 17.743182] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <6>[ 17.751200] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 17.780051] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <4>[ 17.800522] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 17.814909] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <4>[ 17.870972] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 17.941909] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 18.039533] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 18.106126] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 18.113714] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 18.131414] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 18.187089] mscc_felix 0000:00:00.5: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 18.212573] CAN device driver interface <6>[ 18.270299] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.482116] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.655832] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.733421] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 18.756320] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 18.785005] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.821088] device enp0s0f2 entered promiscuous mode <6>[ 18.836259] device enp0s0f6 entered promiscuous mode <6>[ 18.848747] DSA: tree 0 setup <6>[ 18.943075] mali-dp f080000.display: Adding to iommu group 15 <6>[ 18.971743] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 18.982989] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 18.998442] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 19.291414] caam_jr 8010000.jr: Adding to iommu group 16 <6>[ 19.310449] caam algorithms registered in /proc/crypto <6>[ 19.320860] caam 8000000.crypto: registering rng-caam <6>[ 19.328428] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.337079] caam_jr 8020000.jr: Adding to iommu group 17 <6>[ 19.345308] caam_jr 8030000.jr: Adding to iommu group 18 <6>[ 19.353917] caam_jr 8040000.jr: Adding to iommu group 19 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-350887/environment . /lava-350887/environment / # /lava-350887/bin/lava-test-runner /lava-350887/0 /lava-350887/bin/lava-test-runner /lava-350887/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-350887/0/tests/0_dmesg + cat uuid + UUID=350887_1.5.<8>[ 20.415496] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 20.514013] <8>[ 20.611180] <8>[ 20.712520] + set +x <8>[ 20.731157] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-350887/environment / # . /lava-350887/environment/lava-350887/bin/lava-test-runner /lava-350887/1 / # /lava-350887/bin/lava-test-runner /lava-350887/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-350887/1/tests/1_bootrr + cat uuid + UUID=350887_1.5.<8>[ 21.333604] 2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-350887/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-350887/1/../bin/lava-test-case <8>[ 21.456618] /lava-350887/1/../bin/lava-test-case <8>[ 21.551935] /lava-350887/1/../bin/lava-test-case <8>[ 21.602949] /lava-350887/1/../bin/lava-test-case <8>[ 21.720986] /lava-350887/1/../bin/lava-test-case <8>[ 21.808877] /lava-350887/1/../bin/lava-test-case <8>[ 21.878910] /lava-350887/1/../bin/lava-test-case <8>[ 21.966398] /lava-350887/1/../bin/lava-test-case <8>[ 22.036504] /lava-350887/1/../bin/lava-test-case <8>[ 22.125891] /lava-350887/1/../bin/lava-test-case <8>[ 22.198089] /lava-350887/1/../bin/lava-test-case <8>[ 22.284135] /lava-350887/1/../bin/lava-test-case <8>[ 22.386140] /lava-350887/1/../bin/lava-test-case <8>[ 22.490456] /lava-350887/1/../bin/lava-test-case <8>[ 22.579053] /lava-350887/1/../bin/lava-test-case <8>[ 22.649266] /lava-350887/1/../bin/lava-test-case <8>[ 22.736239] /lava-350887/1/../bin/lava-test-case <8>[ 22.840543] /lava-350887/1/../bin/lava-test-case <8>[ 22.925756] /lava-350887/1/../bin/lava-test-case <8>[ 22.995032] /lava-350887/1/../bin/lava-test-case <8>[ 23.081669] /lava-350887/1/../bin/lava-test-case <8>[ 23.150454] /lava-350887/1/../bin/lava-test-case <8>[ 23.240870] /lava-350887/1/../bin/lava-test-case <8>[ 23.333121] /lava-350887/1/../bin/lava-test-case <8>[ 23.425637] /lava-350887/1/../bin/lava-test-case <8>[ 23.494184] /lava-350887/1/../bin/lava-test-case <8>[ 23.581436] /lava-350887/1/../bin/lava-test-case <8>[ 23.650318] /lava-350887/1/../bin/lava-test-case <8>[ 23.737069] /lava-350887/1/../bin/lava-test-case <8>[ 23.809374] /lava-350887/1/../bin/lava-test-case <8>[ 23.897458] /lava-350887/1/../bin/lava-test-case <8>[ 23.984439] /lava-350887/1/../bin/lava-test-case <8>[ 24.057360] /lava-350887/1/../bin/lava-test-case <8>[ 24.145255] /lava-350887/1/../bin/lava-test-case <8>[ 24.232486] /lava-350887/1/../bin/lava-test-case <8>[ 24.304594] /lava-350887/1/../bin/lava-test-case <8>[ 24.393957] /lava-350887/1/../bin/lava-test-case <8>[ 24.462441] /lava-350887/1/../bin/lava-test-case <8>[ 24.551630] /lava-350887/1/../bin/lava-test-case <8>[ 24.621509] /lava-350887/1/../bin/lava-test-case <8>[ 24.709039] /lava-350887/1/../bin/lava-test-case <8>[ 24.796951] /lava-350887/1/../bin/lava-test-case <8>[ 24.866745] /lava-350887/1/../bin/lava-test-case <8>[ 24.954292] /lava-350887/1/../bin/lava-test-case <8>[ 25.041640] /lava-350887/1/../bin/lava-test-case <8>[ 25.111083] /lava-350887/1/../bin/lava-test-case <8>[ 25.200860] /lava-350887/1/../bin/lava-test-case <8>[ 25.289573] /lava-350887/1/../bin/lava-test-case <8>[ 25.359827] /lava-350887/1/../bin/lava-test-case <8>[ 25.449664] /lava-350887/1/../bin/lava-test-case <8>[ 25.518532] /lava-350887/1/../bin/lava-test-case <8>[ 25.605126] /lava-350887/1/../bin/lava-test-case <8>[ 25.677307] /lava-350887/1/../bin/lava-test-case <8>[ 25.764367] /lava-350887/1/../bin/lava-test-case <8>[ 25.852280] /lava-350887/1/../bin/lava-test-case <8>[ 25.940066] /lava-350887/1/../bin/lava-test-case <8>[ 26.029110] /lava-350887/1/../bin/lava-test-case <8>[ 26.098690] /lava-350887/1/../bin/lava-test-case <8>[ 26.190294] /lava-350887/1/../bin/lava-test-case <8>[ 26.281237] /lava-350887/1/../bin/lava-test-case <8>[ 26.350684] /lava-350887/1/../bin/lava-test-case <8>[ 26.443229] /lava-350887/1/../bin/lava-test-case <8>[ 26.512562] /lava-350887/1/../bin/lava-test-case <8>[ 26.600192] /lava-350887/1/../bin/lava-test-case <8>[ 26.673339] /lava-350887/1/../bin/lava-test-case <8>[ 26.763998] /lava-350887/1/../bin/lava-test-case <8>[ 26.833127] /lava-350887/1/../bin/lava-test-case <8>[ 26.920883] /lava-350887/1/../bin/lava-test-case <8>[ 26.993495] /lava-350887/1/../bin/lava-test-case <8>[ 27.078562] /lava-350887/1/../bin/lava-test-case <8>[ 27.146441] /lava-350887/1/../bin/lava-test-case <8>[ 27.237513] /lava-350887/1/../bin/lava-test-case <8>[ 27.306677] /lava-350887/1/../bin/lava-test-case <8>[ 27.395980] /lava-350887/1/../bin/lava-test-case <8>[ 27.465768] /lava-350887/1/../bin/lava-test-case <8>[ 27.553537] /lava-350887/1/../bin/lava-test-case <8>[ 27.640695] /lava-350887/1/../bin/lava-test-case <8>[ 27.713243] /lava-350887/1/../bin/lava-test-case <8>[ 27.800371] /lava-350887/1/../bin/lava-test-case <8>[ 27.891753] /lava-350887/1/../bin/lava-test-case <8>[ 27.979879] /lava-350887/1/../bin/lava-test-case <8>[ 28.068352] /lava-350887/1/../bin/lava-test-case <8>[ 28.142633] /lava-350887/1/../bin/lava-test-case <8>[ 28.232140] /lava-350887/1/../bin/lava-test-case <8>[ 28.302003] /lava-350887/1/../bin/lava-test-case <8>[ 28.388046] /lava-350887/1/../bin/lava-test-case <8>[ 28.455716] /lava-350887/1/../bin/lava-test-case <8>[ 28.542742] /lava-350887/1/../bin/lava-test-case <8>[ 28.630171] /lava-350887/1/../bin/lava-test-case <8>[ 28.699160] /lava-350887/1/../bin/lava-test-case <8>[ 28.785365] /lava-350887/1/../bin/lava-test-case <8>[ 28.854819] /lava-350887/1/../bin/lava-test-case <8>[ 28.944638] + set +x <8>[ 28.975600] / #