Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 20:57:22, Jun 27 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 20:57:30, Jun 27 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gc873063750 (Jun 27 2019 - 18:08:01 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 0 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1000 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:3f:90:5c DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - d6:15:34:f0:d1:b2 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - de:1d:1d:8a:5d:be , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 86:e0:48:96:e6:2f , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 8e:e8:61:ec:6a:23 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - b6:b3:9c:4c:83:2b , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - be:bb:b5:36:0f:27 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 22:0a:b8:e3:52:72 , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 2a:02:91:99:de:7e , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.14; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.14; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1233936/tftp-deploy-or4qbk1x/kernel/uImage tftp 0x80080000 1233936/tftp-deploy-or4qbk1x/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1233936/tftp-deploy-or4qbk1x/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 4.2 MiB/s done Bytes transferred = 37358144 (23a0a40 hex) => tftp 0x91000000 1233936/tftp-deploy-or4qbk1x/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1233936/tftp-deploy-or4qbk1x/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1233936/tftp-deploy-or4qbk1x/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 3 MiB/s done Bytes transferred = 22133492 (151baf4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1233936/tftp-deploy-or4qbk1x/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1233936/tftp-deploy-or4qbk1x/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1233936/tftp-deploy-or4qbk1x/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 4.9 KiB/s done Bytes transferred = 25742 (648e hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-14 2:42:40 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 37358080 Bytes = 35.6 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-14 2:42:45 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22133428 Bytes = 21.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 000000009000948d fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 6.1.31 (KernelCI@build-j1612555-arm64-gcc-10-defconfig-nxrtt) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Mon Jun 5 22:38:01 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3eba00-0x837e3edfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9e00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 20 pages/cpu s44840 r8192 d28888 u81920 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Unknown kernel command line parameters \"nousb\", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 8. [ 0.000000] software IO TLB: mapped [mem 0x00000000f5e00000-0x00000000f9e00000] (64MB) [ 0.000000] Memory: 14171284K/14612480K available (16192K kernel code, 3714K rwdata, 8860K rodata, 7552K init, 609K bss, 408428K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080050000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080060000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080070000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000000] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008366] Console: colour dummy device 80x25 [ 0.012869] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023287] pid_max: default: 32768 minimum: 301 [ 0.027956] LSM: Security Framework initializing [ 0.032657] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.040298] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.048987] cblist_init_generic: Setting adjustable number of callback queues. [ 0.056269] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.062427] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.068628] rcu: Hierarchical SRCU implementation. [ 0.073448] rcu: Max phase no-delay instances is 1000. [ 0.078801] Platform MSI: gic-its@6020000 domain created [ 0.084190] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.091756] fsl-mc MSI: gic-its@6020000 domain created [ 0.097462] EFI services will not be available. [ 0.102184] smp: Bringing up secondary CPUs ... [ 0.106963] Detected PIPT I-cache on CPU1 [ 0.107001] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.107010] GICv3: CPU1: using allocated LPI pending table @0x0000008080080000 [ 0.107030] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.107294] Detected PIPT I-cache on CPU2 [ 0.107345] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.107355] GICv3: CPU2: using allocated LPI pending table @0x0000008080090000 [ 0.107373] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.107626] Detected PIPT I-cache on CPU3 [ 0.107658] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.107666] GICv3: CPU3: using allocated LPI pending table @0x00000080800a0000 [ 0.107681] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.107925] Detected PIPT I-cache on CPU4 [ 0.107972] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.107982] GICv3: CPU4: using allocated LPI pending table @0x00000080800b0000 [ 0.108000] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.108255] Detected PIPT I-cache on CPU5 [ 0.108287] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.108295] GICv3: CPU5: using allocated LPI pending table @0x00000080800c0000 [ 0.108310] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.108557] Detected PIPT I-cache on CPU6 [ 0.108612] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.108622] GICv3: CPU6: using allocated LPI pending table @0x00000080800d0000 [ 0.108641] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.108896] Detected PIPT I-cache on CPU7 [ 0.108931] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.108940] GICv3: CPU7: using allocated LPI pending table @0x00000080800e0000 [ 0.108954] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.108990] smp: Brought up 1 node, 8 CPUs [ 0.287568] SMP: Total of 8 processors activated. [ 0.292299] CPU features: detected: 32-bit EL0 Support [ 0.297475] CPU features: detected: 32-bit EL1 Support [ 0.302643] CPU features: detected: CRC32 instructions [ 0.307853] CPU: All CPU(s) started at EL2 [ 0.311979] alternatives: applying system-wide alternatives [ 0.318497] devtmpfs: initialized [ 0.325897] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.335712] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.343010] pinctrl core: initialized pinctrl subsystem [ 0.348587] Machine: Freescale Layerscape 2088A RDB Board [ 0.354019] SoC family: QorIQ LS2088A [ 0.357694] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.362632] DMI not present or invalid. [ 0.366786] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.373362] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.380898] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.389082] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.397160] audit: initializing netlink subsys (disabled) [ 0.402646] audit: type=2000 audit(0.264:1): state=initialized audit_enabled=0 res=1 [ 0.403047] thermal_sys: Registered thermal governor 'step_wise' [ 0.410443] thermal_sys: Registered thermal governor 'power_allocator' [ 0.416511] cpuidle: using governor menu [ 0.427099] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.434000] ASID allocator initialised with 32768 entries [ 0.440068] Serial: AMBA PL011 UART driver [ 0.451458] KASLR enabled [ 0.460045] HugeTLB: registered 2.00 MiB page size, pre-allocated 256 pages [ 0.467063] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.473371] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.480199] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.486504] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.493335] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.499641] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.506470] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.513535] ACPI: Interpreter disabled. [ 0.518283] iommu: Default domain type: Translated [ 0.523209] iommu: DMA domain TLB invalidation policy: strict mode [ 0.529614] SCSI subsystem initialized [ 0.533531] usbcore: registered new interface driver usbfs [ 0.539059] usbcore: registered new interface driver hub [ 0.544416] usbcore: registered new device driver usb [ 0.549756] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.557125] i2c i2c-0: IMX I2C adapter registered [ 0.562080] pps_core: LinuxPPS API ver. 1 registered [ 0.567075] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.576282] PTP clock support registered [ 0.580275] EDAC MC: Ver: 3.0.0 [ 0.583971] fsl-ifc 2240000.memory-controller: Freescale Integrated Flash Controller [ 0.591784] fsl-ifc 2240000.memory-controller: IFC version 2.0, 8 banks [ 0.599017] FPGA manager framework [ 0.602480] Advanced Linux Sound Architecture Driver Initialized. [ 0.608908] vgaarb: loaded [ 0.611784] clocksource: Switched to clocksource arch_sys_counter [ 0.618017] VFS: Disk quotas dquot_6.6.0 [ 0.621976] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.628966] pnp: PnP ACPI: disabled [ 0.635192] NET: Registered PF_INET protocol family [ 0.640337] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.653368] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.662126] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.669933] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.678521] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.686811] TCP: Hash tables configured (established 131072 bind 65536) [ 0.693540] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.700563] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.708069] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.713944] RPC: Registered named UNIX socket transport module. [ 0.719902] RPC: Registered udp transport module. [ 0.724629] RPC: Registered tcp transport module. [ 0.729361] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.735842] PCI: CLS 0 bytes, default 64 [ 0.739855] Unpacking initramfs... [ 0.743676] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.751658] kvm [1]: IPA Size Limit: 44 bits [ 0.756623] kvm [1]: vgic-v2@c0e0000 [ 0.760233] kvm [1]: GIC system register CPU interface enabled [ 0.766211] kvm [1]: vgic interrupt IRQ9 [ 0.770248] kvm [1]: Hyp mode initialized successfully [ 0.776051] Initialise system trusted keyrings [ 0.780615] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 0.789737] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.795895] NFS: Registering the id_resolver key type [ 0.800988] Key type id_resolver registered [ 0.805193] Key type id_legacy registered [ 0.809258] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.816001] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.823521] 9p: Installing v9fs 9p2000 file system support [ 0.849469] Key type asymmetric registered [ 0.853589] Asymmetric key parser 'x509' registered [ 0.858517] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.865962] io scheduler mq-deadline registered [ 0.870517] io scheduler kyber registered [ 0.879870] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 0.887243] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 0.895832] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 0.904763] layerscape-pcie 3600000.pcie: iATU unroll: disabled [ 0.910718] layerscape-pcie 3600000.pcie: iATU regions: 256 ob, 24 ib, align 4K, limit 4G [ 0.919121] layerscape-pcie 3600000.pcie: PCIe Gen.1 x1 link up [ 0.925125] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 0.931863] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.937384] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.943599] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 0.954206] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 0.960252] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 0.966559] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 0.972863] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 0.979989] pci 0000:00:00.0: supports D1 D2 [ 0.984283] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 0.991050] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 0.997192] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 1.003895] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 1.010599] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 1.016253] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 1.023062] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 1.030504] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.047840] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.055026] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.062208] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.069824] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.077088] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.083307] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.090502] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.098118] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.105312] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.112509] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.118652] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.123906] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.130033] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.137310] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.144675] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 1.153257] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 1.161862] layerscape-pcie 3700000.pcie: iATU unroll: disabled [ 1.167817] layerscape-pcie 3700000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G [ 1.283389] Freeing initrd memory: 21608K [ 2.175849] layerscape-pcie 3700000.pcie: Phy link never came up [ 2.181937] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 2.188681] pci_bus 0001:00: root bus resource [bus 00-ff] [ 2.194200] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 2.203213] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.213816] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.219870] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 2.226984] pci 0001:00:00.0: supports D1 D2 [ 2.231275] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 2.237910] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 2.245531] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 2.251324] EINJ: ACPI disabled. [ 2.264214] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.271661] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 19, base_baud = 21875000) is a 16550A [ 2.280745] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 19, base_baud = 21875000) is a 16550A [ 2.289608] printk: console [ttyS1] enabled [ 2.289608] printk: console [ttyS1] enabled [ 2.297992] printk: bootconsole [uart8250] disabled [ 2.297992] printk: bootconsole [uart8250] disabled [ 2.308011] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 20, base_baud = 21875000) is a 16550A [ 2.317008] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 20, base_baud = 21875000) is a 16550A [ 2.326038] SuperH (H)SCI(F) driver initialized [ 2.330786] msm_serial: driver initialized [ 2.336590] arm-smmu 5000000.iommu: probing hardware configuration... [ 2.343033] arm-smmu 5000000.iommu: SMMUv2 with: [ 2.347648] arm-smmu 5000000.iommu: stage 1 translation [ 2.352956] arm-smmu 5000000.iommu: stage 2 translation [ 2.358263] arm-smmu 5000000.iommu: nested translation [ 2.363484] arm-smmu 5000000.iommu: coherent table walk [ 2.368796] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 2.375929] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 2.382458] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 2.388896] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 2.395333] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 2.401976] arm-smmu 5000000.iommu: preserved 0 boot mappings [ 2.411056] loop: module loaded [ 2.414660] megasas: 07.719.03.00-rc1 [ 2.418775] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 2.426315] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 2.433734] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 2.441454] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.450413] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 2.460500] scsi host0: ahci-qoriq [ 2.463996] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 97 [ 2.471971] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 2.479492] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 2.486901] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 2.494614] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.503576] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 2.513474] scsi host1: ahci-qoriq [ 2.516933] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 98 [ 2.525184] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 2.534457] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 2.544548] Amd/Fujitsu Extended Query Table at 0x0040 [ 2.549693] Amd/Fujitsu Extended Query version 1.5. [ 2.554744] number of CFI chips: 1 [ 2.578315] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 2.584682] nand: Micron MT29F16G08ABABAWP [ 2.588774] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 2.597589] Bad block table found at page 524160, version 0x01 [ 2.605504] Bad block table found at page 524032, version 0x01 [ 2.631697] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 2.639675] spi-nor spi0.0: unrecognized JEDEC id bytes: f1 e3 c3 87 8f 1e [ 2.646891] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.655180] tun: Universal TUN/TAP device driver, 1.6 [ 2.660603] thunder_xcv, ver 1.0 [ 2.663851] thunder_bgx, ver 1.0 [ 2.667085] nicpf, ver 1.0 [ 2.786002] ata1: SATA link down (SStatus 0 SControl 300) [ 2.836899] ata2: SATA link down (SStatus 0 SControl 300) [ 3.195105] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 3.202338] hns3: Copyright (c) 2017 Huawei Corporation. [ 3.207667] hclge is initializing [ 3.210986] e1000: Intel(R) PRO/1000 Network Driver [ 3.215859] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3.221617] e1000e: Intel(R) PRO/1000 Network Driver [ 3.226576] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.232566] e1000e 0000:01:00.0: Adding to iommu group 0 [ 3.238372] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 3.296266] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 3.357723] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:3f:90:5c [ 3.365649] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 3.372533] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 3.379265] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.384660] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.390243] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 3.396506] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.402595] sky2: driver version 1.30 [ 3.406739] VFIO - User Level meta-driver version: 0.3 [ 3.413845] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.419359] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.427090] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.436502] xhci-hcd xhci-hcd.0.auto: irq 109, io mem 0x03100000 [ 3.442569] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.448055] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.455711] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.462471] hub 1-0:1.0: USB hub found [ 3.466228] hub 1-0:1.0: 1 port detected [ 3.470270] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.478531] hub 2-0:1.0: USB hub found [ 3.482288] hub 2-0:1.0: 1 port detected [ 3.486341] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.491832] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.499554] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.508959] xhci-hcd xhci-hcd.1.auto: irq 110, io mem 0x03110000 [ 3.515032] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.520517] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 3.528173] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.534875] hub 3-0:1.0: USB hub found [ 3.538631] hub 3-0:1.0: 1 port detected [ 3.542659] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.550917] hub 4-0:1.0: USB hub found [ 3.554672] hub 4-0:1.0: 1 port detected [ 3.558913] usbcore: registered new interface driver usb-storage [ 3.566160] i2c_dev: i2c /dev entries driver [ 3.571818] i2c i2c-0: Added multiplexed i2c bus 1 [ 3.578132] rtc-ds3232 2-0068: oscillator discontinuity flagged, time unreliable [ 3.589313] hwmon hwmon0: temp1_input not attached to any thermal zone [ 3.606073] rtc-ds3232 2-0068: registered as rtc0 [ 3.612711] rtc-ds3232 2-0068: setting system clock to 2022-09-26T10:00:19 UTC (1664186419) [ 3.621196] i2c i2c-0: Added multiplexed i2c bus 2 [ 3.626117] i2c i2c-0: Added multiplexed i2c bus 3 [ 3.631033] i2c i2c-0: Added multiplexed i2c bus 4 [ 3.635900] i2c i2c-0: Added multiplexed i2c bus 5 [ 3.640763] i2c i2c-0: Added multiplexed i2c bus 6 [ 3.645628] i2c i2c-0: Added multiplexed i2c bus 7 [ 3.650492] i2c i2c-0: Added multiplexed i2c bus 8 [ 3.655284] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 3.663931] sp805-wdt c000000.wdt: registration successful [ 3.669520] sp805-wdt c010000.wdt: registration successful [ 3.675098] sp805-wdt c100000.wdt: registration successful [ 3.680680] sp805-wdt c110000.wdt: registration successful [ 3.686254] sp805-wdt c200000.wdt: registration successful [ 3.691836] sp805-wdt c210000.wdt: registration successful [ 3.697414] sp805-wdt c300000.wdt: registration successful [ 3.702991] sp805-wdt c310000.wdt: registration successful [ 3.710222] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 3.718737] sdhci: Secure Digital Host Controller Interface driver [ 3.724930] sdhci: Copyright(c) Pierre Ossman [ 3.729604] Synopsys Designware Multimedia Card Interface Driver [ 3.736042] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.742778] ledtrig-cpu: registered to indicate activity on CPUs [ 3.749753] usbcore: registered new interface driver usbhid [ 3.755342] usbhid: USB HID core driver [ 3.761002] optee: probing for conduit method. [ 3.765448] optee: api uid mismatch [ 3.767815] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 3.768939] optee: probe of firmware:optee failed with error -22 [ 3.783814] NET: Registered PF_PACKET protocol family [ 3.788933] 9pnet: Installing 9P2000 support [ 3.793224] Key type dns_resolver registered [ 3.797674] registered taskstats version 1 [ 3.801780] Loading compiled-in X.509 certificates [ 3.811223] pcieport 0000:00:00.0: Adding to iommu group 1 [ 3.816991] pcieport 0000:00:00.0: PME: Signaling with IRQ 105 [ 3.823015] pcieport 0000:00:00.0: AER: enabled with IRQ 105 [ 3.828952] pcieport 0001:00:00.0: Adding to iommu group 2 [ 3.834676] pcieport 0001:00:00.0: PME: Signaling with IRQ 113 [ 3.840755] pcieport 0001:00:00.0: AER: enabled with IRQ 113 [ 6.808795] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 6.847805] Sending DHCP requests ..., OK [ 14.567841] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.190 [ 14.575424] IP-Config: Complete: [ 14.578653] device=eth0, hwaddr=68:05:ca:3f:90:5c, ipaddr=172.16.1.190, mask=255.255.255.0, gw=172.16.1.4 [ 14.588665] host=172.16.1.190, domain=example.org, nis-domain=(none) [ 14.595456] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 14.595462] nameserver0=172.16.1.4 [ 14.605685] ALSA device list: [ 14.608664] No soundcards found. [ 14.615057] Freeing unused kernel memory: 7552K [ 14.623955] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 14.668553] udevd[240]: starting version 3.2.9 [ 16.683785] random: crng init done [ 16.689363] udevd[240]: specified user 'tss' unknown [ 16.694366] udevd[240]: specified group 'tss' unknown [ 16.700236] udevd[241]: starting eudev-3.2.9 [ 16.806252] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) [ 16.816843] fsl_ddr_edac acquired irq 114 for MC [ 16.821618] fsl_ddr_edac MC err registered [ 16.825946] EDAC MC1: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) [ 16.836315] fsl_ddr_edac acquired irq 115 for MC [ 16.841026] fsl_ddr_edac MC err registered [ 16.846273] mtdblock: MTD device '530000000.flash' is NAND, please consider using UBI block devices instead. [ 16.856526] arm-ccn 4000000.ccn: No access to interrupts, using timer. [ 16.869835] udevd[245]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 16.871830] ftm-alarm 2800000.timer: registered as rtc1 [ 16.890205] lm90 4-004c: supply vcc not found, using dummy regulator [ 16.894753] udevd[245]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 16.911641] ina2xx 3-0040: error configuring the device: -6 [ 16.916982] hwmon hwmon1: temp1_input not attached to any thermal zone [ 16.923818] hwmon hwmon1: temp2_input not attached to any thermal zone done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 16.983487] NET: Registered PF_INET6 protocol family [ 16.989226] Segment Routing with IPv6 [ 16.992907] In-situ OAM (IOAM) with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1233936/environment . /lava-1233936/environment / # /lava-1233936/bin/lava-test-runner /lava-1233936/0 /lava-1233936/bin/lava-test-runner /lava-1233936/0 + export 'TESTRUN_ID=0_dmesg' + c[ 17.514360] d /lava-1233936/0/tests/0_dmesg + cat uuid + UUID=1233936_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 17.532856] [ 17.553038] [ 17.574162] + set +x [ 17.583346] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1233936/environment / # . /lava-1233936/environment/lava-1233936/bin/lava-test-runner /lava-1233936/1 / # /lava-1233936/bin/lava-test-runner /lava-1233936/1 + export 'TESTRUN_ID=1_bootrr' + [ 18.024233] cd /lava-1233936/1/tests/1_bootrr + cat uuid + UUID=1233936_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1233936/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1233936/1/../bin/lava-test-case [ 19.048738] /lava-1233936/1/../bin/lava-test-case [ 19.068653] /lava-1233936/1/../bin/lava-test-case [ 19.082844] + [ 19.094500] set +x / #