Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 32:12:77:b5:2e:26 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1234967/tftp-deploy-o99sqmcy/kernel/uImage tftp 0x80080000 1234967/tftp-deploy-o99sqmcy/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1234967/tftp-deploy-o99sqmcy/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 2.6 MiB/s done Bytes transferred = 37358144 (23a0a40 hex) => tftp 0x91000000 1234967/tftp-deploy-o99sqmcy/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1234967/tftp-deploy-o99sqmcy/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1234967/tftp-deploy-o99sqmcy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 2.9 MiB/s done Bytes transferred = 22136260 (151c5c4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1234967/tftp-deploy-o99sqmcy/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1234967/tftp-deploy-o99sqmcy/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1234967/tftp-deploy-o99sqmcy/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 4.9 KiB/s done Bytes transferred = 25742 (648e hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-14 3:19:32 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 37358080 Bytes = 35.6 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-14 3:19:37 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22136196 Bytes = 21.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 000000009000948d fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 6.1.31 (KernelCI@build-j40532-arm64-gcc-10-defconfig-gqkzw) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Thu Jun 15 11:20:52 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3eba00-0x837e3edfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9e00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 20 pages/cpu s44840 r8192 d28888 u81920 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Unknown kernel command line parameters \"nousb\", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 8. [ 0.000000] software IO TLB: mapped [mem 0x00000000f5e00000-0x00000000f9e00000] (64MB) [ 0.000000] Memory: 14171280K/14612480K available (16192K kernel code, 3714K rwdata, 8860K rodata, 7552K init, 609K bss, 408432K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080050000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080060000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080070000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000000] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008365] Console: colour dummy device 80x25 [ 0.012866] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023295] pid_max: default: 32768 minimum: 301 [ 0.027963] LSM: Security Framework initializing [ 0.032666] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.040307] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.048996] cblist_init_generic: Setting adjustable number of callback queues. [ 0.056279] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.062440] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.068643] rcu: Hierarchical SRCU implementation. [ 0.073463] rcu: Max phase no-delay instances is 1000. [ 0.078817] Platform MSI: gic-its@6020000 domain created [ 0.084208] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.091770] fsl-mc MSI: gic-its@6020000 domain created [ 0.097483] EFI services will not be available. [ 0.102202] smp: Bringing up secondary CPUs ... [ 0.106988] Detected PIPT I-cache on CPU1 [ 0.107028] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.107038] GICv3: CPU1: using allocated LPI pending table @0x0000008080080000 [ 0.107057] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.107324] Detected PIPT I-cache on CPU2 [ 0.107374] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.107384] GICv3: CPU2: using allocated LPI pending table @0x0000008080090000 [ 0.107403] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.107653] Detected PIPT I-cache on CPU3 [ 0.107684] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.107692] GICv3: CPU3: using allocated LPI pending table @0x00000080800a0000 [ 0.107706] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.107948] Detected PIPT I-cache on CPU4 [ 0.108000] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.108009] GICv3: CPU4: using allocated LPI pending table @0x00000080800b0000 [ 0.108028] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.108287] Detected PIPT I-cache on CPU5 [ 0.108319] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.108327] GICv3: CPU5: using allocated LPI pending table @0x00000080800c0000 [ 0.108341] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.108586] Detected PIPT I-cache on CPU6 [ 0.108640] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.108650] GICv3: CPU6: using allocated LPI pending table @0x00000080800d0000 [ 0.108668] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.108923] Detected PIPT I-cache on CPU7 [ 0.108958] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.108967] GICv3: CPU7: using allocated LPI pending table @0x00000080800e0000 [ 0.108981] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.109017] smp: Brought up 1 node, 8 CPUs [ 0.287569] SMP: Total of 8 processors activated. [ 0.292301] CPU features: detected: 32-bit EL0 Support [ 0.297475] CPU features: detected: 32-bit EL1 Support [ 0.302649] CPU features: detected: CRC32 instructions [ 0.307861] CPU: All CPU(s) started at EL2 [ 0.311989] alternatives: applying system-wide alternatives [ 0.318509] devtmpfs: initialized [ 0.325906] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.335720] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.343012] pinctrl core: initialized pinctrl subsystem [ 0.348588] Machine: Freescale Layerscape 2088A RDB Board [ 0.354020] SoC family: QorIQ LS2088A [ 0.357699] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.362634] DMI not present or invalid. [ 0.366787] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.373363] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.380897] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.389076] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.397155] audit: initializing netlink subsys (disabled) [ 0.402643] audit: type=2000 audit(0.264:1): state=initialized audit_enabled=0 res=1 [ 0.403059] thermal_sys: Registered thermal governor 'step_wise' [ 0.410441] thermal_sys: Registered thermal governor 'power_allocator' [ 0.416508] cpuidle: using governor menu [ 0.427090] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.433991] ASID allocator initialised with 32768 entries [ 0.440045] Serial: AMBA PL011 UART driver [ 0.451490] KASLR enabled [ 0.459981] HugeTLB: registered 2.00 MiB page size, pre-allocated 256 pages [ 0.467001] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.473308] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.480132] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.486441] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.493269] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.499573] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.506399] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.513467] ACPI: Interpreter disabled. [ 0.518221] iommu: Default domain type: Translated [ 0.523153] iommu: DMA domain TLB invalidation policy: strict mode [ 0.529562] SCSI subsystem initialized [ 0.533479] usbcore: registered new interface driver usbfs [ 0.539011] usbcore: registered new interface driver hub [ 0.544366] usbcore: registered new device driver usb [ 0.549705] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.557076] i2c i2c-0: IMX I2C adapter registered [ 0.562031] pps_core: LinuxPPS API ver. 1 registered [ 0.567024] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.576232] PTP clock support registered [ 0.580222] EDAC MC: Ver: 3.0.0 [ 0.583921] fsl-ifc 2240000.memory-controller: Freescale Integrated Flash Controller [ 0.591733] fsl-ifc 2240000.memory-controller: IFC version 2.0, 8 banks [ 0.598971] FPGA manager framework [ 0.602433] Advanced Linux Sound Architecture Driver Initialized. [ 0.608852] vgaarb: loaded [ 0.611726] clocksource: Switched to clocksource arch_sys_counter [ 0.617956] VFS: Disk quotas dquot_6.6.0 [ 0.621915] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.628905] pnp: PnP ACPI: disabled [ 0.635129] NET: Registered PF_INET protocol family [ 0.640273] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.653302] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.662058] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.669861] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.678452] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.686737] TCP: Hash tables configured (established 131072 bind 65536) [ 0.693467] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.700488] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.707997] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.713868] RPC: Registered named UNIX socket transport module. [ 0.719828] RPC: Registered udp transport module. [ 0.724556] RPC: Registered tcp transport module. [ 0.729284] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.735768] PCI: CLS 0 bytes, default 64 [ 0.739825] Unpacking initramfs... [ 0.743514] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.751493] kvm [1]: IPA Size Limit: 44 bits [ 0.756455] kvm [1]: vgic-v2@c0e0000 [ 0.760066] kvm [1]: GIC system register CPU interface enabled [ 0.766040] kvm [1]: vgic interrupt IRQ9 [ 0.770078] kvm [1]: Hyp mode initialized successfully [ 0.775843] Initialise system trusted keyrings [ 0.780394] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 0.789539] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.795690] NFS: Registering the id_resolver key type [ 0.800781] Key type id_resolver registered [ 0.804985] Key type id_legacy registered [ 0.809054] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.815795] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.823296] 9p: Installing v9fs 9p2000 file system support [ 0.850256] Key type asymmetric registered [ 0.854373] Asymmetric key parser 'x509' registered [ 0.859301] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.866745] io scheduler mq-deadline registered [ 0.871301] io scheduler kyber registered [ 0.880655] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 0.888029] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 0.896620] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 0.905555] layerscape-pcie 3600000.pcie: iATU unroll: disabled [ 0.911507] layerscape-pcie 3600000.pcie: iATU regions: 256 ob, 24 ib, align 4K, limit 4G [ 0.919910] layerscape-pcie 3600000.pcie: PCIe Gen.1 x1 link up [ 0.925913] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 0.932659] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.938177] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.944401] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 0.955012] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 0.961067] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 0.967374] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 0.973686] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 0.980810] pci 0000:00:00.0: supports D1 D2 [ 0.985106] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 0.991929] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 0.998067] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 1.004776] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 1.011483] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 1.017137] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 1.023944] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 1.031390] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.047789] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.054975] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.062173] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.069794] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.077068] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.083287] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.090485] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.098103] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.105296] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.112489] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.118637] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.123892] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.130026] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.137321] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.144690] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 1.153273] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 1.161883] layerscape-pcie 3700000.pcie: iATU unroll: disabled [ 1.167839] layerscape-pcie 3700000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G [ 1.282942] Freeing initrd memory: 21612K [ 2.175877] layerscape-pcie 3700000.pcie: Phy link never came up [ 2.181979] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 2.188726] pci_bus 0001:00: root bus resource [bus 00-ff] [ 2.194247] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 2.203273] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.213882] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.219937] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 2.227056] pci 0001:00:00.0: supports D1 D2 [ 2.231350] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 2.238022] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 2.245642] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 2.251422] EINJ: ACPI disabled. [ 2.264336] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.271811] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 19, base_baud = 21875000) is a 16550A [ 2.280892] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 19, base_baud = 21875000) is a 16550A [ 2.289756] printk: console [ttyS1] enabled [ 2.289756] printk: console [ttyS1] enabled [ 2.298138] printk: bootconsole [uart8250] disabled [ 2.298138] printk: bootconsole [uart8250] disabled [ 2.308150] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 20, base_baud = 21875000) is a 16550A [ 2.317151] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 20, base_baud = 21875000) is a 16550A [ 2.326184] SuperH (H)SCI(F) driver initialized [ 2.330933] msm_serial: driver initialized [ 2.336738] arm-smmu 5000000.iommu: probing hardware configuration... [ 2.343181] arm-smmu 5000000.iommu: SMMUv2 with: [ 2.347797] arm-smmu 5000000.iommu: stage 1 translation [ 2.353104] arm-smmu 5000000.iommu: stage 2 translation [ 2.358410] arm-smmu 5000000.iommu: nested translation [ 2.363630] arm-smmu 5000000.iommu: coherent table walk [ 2.368941] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 2.376075] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 2.382600] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 2.389038] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 2.395475] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 2.402120] arm-smmu 5000000.iommu: preserved 0 boot mappings [ 2.411209] loop: module loaded [ 2.414817] megasas: 07.719.03.00-rc1 [ 2.418933] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 2.426465] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 2.433888] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 2.441610] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.450570] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 2.460664] scsi host0: ahci-qoriq [ 2.464159] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 97 [ 2.472134] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 2.479652] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 2.487062] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 2.494774] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.503735] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 2.513628] scsi host1: ahci-qoriq [ 2.517090] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 98 [ 2.525347] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 2.534619] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 2.544708] Amd/Fujitsu Extended Query Table at 0x0040 [ 2.549852] Amd/Fujitsu Extended Query version 1.3. [ 2.554904] number of CFI chips: 1 [ 2.578688] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 2.585045] nand: Micron MT29F16G08ABABAWP [ 2.589135] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 2.597949] Bad block table found at page 524160, version 0x01 [ 2.605860] Bad block table found at page 524032, version 0x01 [ 2.631457] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 2.639463] spi-nor spi0.0: unrecognized JEDEC id bytes: 8f 1e 1c 38 70 e1 [ 2.646687] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.654979] tun: Universal TUN/TAP device driver, 1.6 [ 2.660403] thunder_xcv, ver 1.0 [ 2.663636] thunder_bgx, ver 1.0 [ 2.666876] nicpf, ver 1.0 [ 2.789870] ata1: SATA link down (SStatus 0 SControl 300) [ 2.840770] ata2: SATA link down (SStatus 0 SControl 300) [ 3.188222] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 3.195451] hns3: Copyright (c) 2017 Huawei Corporation. [ 3.200782] hclge is initializing [ 3.204099] e1000: Intel(R) PRO/1000 Network Driver [ 3.208971] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3.214729] e1000e: Intel(R) PRO/1000 Network Driver [ 3.219688] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.225683] e1000e 0000:01:00.0: Adding to iommu group 0 [ 3.231485] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 3.288198] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 3.349668] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 3.357595] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 3.364478] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 3.371209] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.376604] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.382190] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 3.388453] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.394543] sky2: driver version 1.30 [ 3.398677] VFIO - User Level meta-driver version: 0.3 [ 3.405783] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.411299] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.419029] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.428443] xhci-hcd xhci-hcd.0.auto: irq 109, io mem 0x03100000 [ 3.434515] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.439999] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.447654] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.454420] hub 1-0:1.0: USB hub found [ 3.458177] hub 1-0:1.0: 1 port detected [ 3.462226] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.470489] hub 2-0:1.0: USB hub found [ 3.474245] hub 2-0:1.0: 1 port detected [ 3.478304] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.483795] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.491518] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.500922] xhci-hcd xhci-hcd.1.auto: irq 110, io mem 0x03110000 [ 3.506992] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.512477] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 3.520134] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.526838] hub 3-0:1.0: USB hub found [ 3.530595] hub 3-0:1.0: 1 port detected [ 3.534622] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.542881] hub 4-0:1.0: USB hub found [ 3.546636] hub 4-0:1.0: 1 port detected [ 3.550874] usbcore: registered new interface driver usb-storage [ 3.558132] i2c_dev: i2c /dev entries driver [ 3.563791] i2c i2c-0: Added multiplexed i2c bus 1 [ 3.570106] rtc-ds3232 2-0068: oscillator discontinuity flagged, time unreliable [ 3.581248] hwmon hwmon0: temp1_input not attached to any thermal zone [ 3.597954] rtc-ds3232 2-0068: registered as rtc0 [ 3.604580] rtc-ds3232 2-0068: setting system clock to 2022-08-04T16:43:06 UTC (1659631386) [ 3.613069] i2c i2c-0: Added multiplexed i2c bus 2 [ 3.617997] i2c i2c-0: Added multiplexed i2c bus 3 [ 3.622912] i2c i2c-0: Added multiplexed i2c bus 4 [ 3.627779] i2c i2c-0: Added multiplexed i2c bus 5 [ 3.632644] i2c i2c-0: Added multiplexed i2c bus 6 [ 3.637508] i2c i2c-0: Added multiplexed i2c bus 7 [ 3.642370] i2c i2c-0: Added multiplexed i2c bus 8 [ 3.647160] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 3.655826] sp805-wdt c000000.wdt: registration successful [ 3.661415] sp805-wdt c010000.wdt: registration successful [ 3.666991] sp805-wdt c100000.wdt: registration successful [ 3.672576] sp805-wdt c110000.wdt: registration successful [ 3.678155] sp805-wdt c200000.wdt: registration successful [ 3.683739] sp805-wdt c210000.wdt: registration successful [ 3.689317] sp805-wdt c300000.wdt: registration successful [ 3.694894] sp805-wdt c310000.wdt: registration successful [ 3.702005] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 3.710524] sdhci: Secure Digital Host Controller Interface driver [ 3.716726] sdhci: Copyright(c) Pierre Ossman [ 3.721522] Synopsys Designware Multimedia Card Interface Driver [ 3.727967] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.734658] ledtrig-cpu: registered to indicate activity on CPUs [ 3.741683] usbcore: registered new interface driver usbhid [ 3.747269] usbhid: USB HID core driver [ 3.752956] optee: probing for conduit method. [ 3.757400] optee: api uid mismatch [ 3.759763] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 3.760885] optee: probe of firmware:optee failed with error -22 [ 3.775800] NET: Registered PF_PACKET protocol family [ 3.780924] 9pnet: Installing 9P2000 support [ 3.785219] Key type dns_resolver registered [ 3.789657] registered taskstats version 1 [ 3.793761] Loading compiled-in X.509 certificates [ 3.802481] pcieport 0000:00:00.0: Adding to iommu group 1 [ 3.808257] pcieport 0000:00:00.0: PME: Signaling with IRQ 105 [ 3.814281] pcieport 0000:00:00.0: AER: enabled with IRQ 105 [ 3.820468] pcieport 0001:00:00.0: Adding to iommu group 2 [ 3.826180] pcieport 0001:00:00.0: PME: Signaling with IRQ 113 [ 3.832171] pcieport 0001:00:00.0: AER: enabled with IRQ 113 [ 6.492740] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 6.523747] Sending DHCP requests ..., OK [ 14.655805] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 14.663389] IP-Config: Complete: [ 14.666619] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 14.676630] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 14.683420] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 14.683426] nameserver0=172.16.1.4 [ 14.693655] ALSA device list: [ 14.696637] No soundcards found. [ 14.703032] Freeing unused kernel memory: 7552K [ 14.711871] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 14.756494] udevd[240]: starting version 3.2.9 [ 16.739726] random: crng init done [ 16.745243] udevd[240]: specified user 'tss' unknown [ 16.750245] udevd[240]: specified group 'tss' unknown [ 16.756137] udevd[241]: starting eudev-3.2.9 [ 16.859120] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) [ 16.875876] fsl_ddr_edac acquired irq 114 for MC [ 16.880650] fsl_ddr_edac MC err registered [ 16.910035] EDAC MC1: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) [ 16.920526] fsl_ddr_edac acquired irq 115 for MC [ 16.925198] fsl_ddr_edac MC err registered [ 16.941062] arm-ccn 4000000.ccn: No access to interrupts, using timer. [ 16.952428] mtdblock: MTD device '530000000.flash' is NAND, please consider using UBI block devices instead. [ 16.959574] ftm-alarm 2800000.timer: registered as rtc1 [ 16.967853] lm90 4-004c: supply vcc not found, using dummy regulator [ 16.974604] ina2xx 3-0040: error configuring the device: -6 [ 16.981420] udevd[270]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 16.990346] udevd[270]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 17.015252] hwmon hwmon8: temp1_input not attached to any thermal zone [ 17.021835] hwmon hwmon8: temp2_input not attached to any thermal zone done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 17.080448] NET: Registered PF_INET6 protocol family [ 17.086183] Segment Routing with IPv6 [ 17.089860] In-situ OAM (IOAM) with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1234967/environment . /lava-1234967/environment / # /lava-1234967/bin/lava-test-runner /lava-1234967/0 /lava-1234967/bin/lava-test-runner /lava-1234967/0 + export 'TESTRUN_ID=0_dmesg' + c[ 17.614407] d /lava-1234967/0/tests/0_dmesg + cat uuid + UUID=1234967_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 17.632444] [ 17.652071] [ 17.674226] + [ 17.683308] set +x # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1234967/environment / # . /lava-1234967/environment/lava-1234967/bin/lava-test-runner /lava-1234967/1 / # /lava-1234967/bin/lava-test-runner /lava-1234967/1 + export 'TESTRUN_ID=1_bootrr' + [ 18.124168] cd /lava-1234967/1/tests/1_bootrr + cat uuid + UUID=1234967_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1234967/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1234967/1/../bin/lava-test-case [ 19.148715] /lava-1234967/1/../bin/lava-test-case [ 19.168704] /lava-1234967/1/../bin/lava-test-case [ 19.182964] + [ 19.194463] set +x / #