Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 32:12:77:b5:2e:26 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1242009/tftp-deploy-sh64_bs9/kernel/uImage tftp 0x80080000 1242009/tftp-deploy-sh64_bs9/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1242009/tftp-deploy-sh64_bs9/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 5 MiB/s done Bytes transferred = 52841024 (3264a40 hex) => tftp 0x91000000 1242009/tftp-deploy-sh64_bs9/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1242009/tftp-deploy-sh64_bs9/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1242009/tftp-deploy-sh64_bs9/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################################### 2.1 MiB/s done Bytes transferred = 27254860 (19fe04c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1242009/tftp-deploy-sh64_bs9/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1242009/tftp-deploy-sh64_bs9/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1242009/tftp-deploy-sh64_bs9/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 4.9 KiB/s done Bytes transferred = 25742 (648e hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-08-09 4:37:49 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 52840960 Bytes = 50.4 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-08-09 4:37:55 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 27254796 Bytes = 26 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 000000009000948d fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 6.1.42-cip2 (KernelCI@build-j7142-arm64-gcc-10-defconfig-kselftest-l9vjc) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Wed Aug 9 04:22:31 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3e8640-0x837e3eafff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9e00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 31 pages/cpu s89696 r8192 d29088 u126976 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Unknown kernel command line parameters \"nousb\", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:on [ 0.000000] mem auto-init: clearing system memory may take some time... [ 0.000000] stackdepot hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] software IO TLB: area num 8. [ 0.000000] software IO TLB: mapped [mem 0x00000000f5e00000-0x00000000f9e00000] (64MB) [ 0.000000] Memory: 14131800K/14612480K available (21888K kernel code, 5842K rwdata, 11844K rodata, 11904K init, 11400K bss, 447912K reserved, 32768K cma-reserved) [ 0.000000] ********************************************************** [ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000] ** ** [ 0.000000] ** This system shows unhashed kernel memory addresses ** [ 0.000000] ** via the console, logs, and other interfaces. This ** [ 0.000000] ** might reduce the security of your system. ** [ 0.000000] ** ** [ 0.000000] ** If you see this message and you are not debugging ** [ 0.000000] ** the kernel, report this immediately to your system ** [ 0.000000] ** administrator! ** [ 0.000000] ** ** [ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000] ********************************************************** [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] ftrace: allocating 66009 entries in 258 pages [ 0.000000] ftrace: allocated 258 pages with 2 groups [ 0.000000] trace event string verifier disabled [ 0.000000] Running RCU self tests [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080330000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080340000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080350000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000000] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008618] Console: colour dummy device 80x25 [ 0.013113] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.020917] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.025047] ... MAX_LOCK_DEPTH: 48 [ 0.029265] ... MAX_LOCKDEP_KEYS: 8192 [ 0.033656] ... CLASSHASH_SIZE: 4096 [ 0.038047] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.042527] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.047007] ... CHAINHASH_SIZE: 32768 [ 0.051489] memory used by lock dependency info: 6365 kB [ 0.056930] memory used for stack traces: 4224 kB [ 0.061760] per task-struct memory footprint: 1920 bytes [ 0.067306] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.077741] pid_max: default: 32768 minimum: 301 [ 0.082684] LSM: Security Framework initializing [ 0.087404] landlock: Up and running. [ 0.091121] LSM support for eBPF active [ 0.095230] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.102866] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.115611] cblist_init_generic: Setting adjustable number of callback queues. [ 0.122917] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.129262] cblist_init_generic: Setting adjustable number of callback queues. [ 0.136570] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.142906] cblist_init_generic: Setting adjustable number of callback queues. [ 0.150211] cblist_init_generic: Setting shift to 3 and lim to 1. [ 0.156536] Running RCU-tasks wait API self tests [ 0.266153] rcu: Hierarchical SRCU implementation. [ 0.270999] rcu: Max phase no-delay instances is 1000. [ 0.276329] Callback from call_rcu_tasks_trace() invoked. [ 0.287782] Platform MSI: gic-its@6020000 domain created [ 0.293318] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.300954] fsl-mc MSI: gic-its@6020000 domain created [ 0.306752] EFI services will not be available. [ 0.312496] smp: Bringing up secondary CPUs ... [ 0.318488] Detected PIPT I-cache on CPU1 [ 0.318547] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.318558] GICv3: CPU1: using allocated LPI pending table @0x0000008080360000 [ 0.318594] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.320082] Detected PIPT I-cache on CPU2 [ 0.320146] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.320156] GICv3: CPU2: using allocated LPI pending table @0x0000008080370000 [ 0.320185] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.321624] Detected PIPT I-cache on CPU3 [ 0.321669] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.321679] GICv3: CPU3: using allocated LPI pending table @0x0000008080380000 [ 0.321700] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.323045] Detected PIPT I-cache on CPU4 [ 0.323115] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.323126] GICv3: CPU4: using allocated LPI pending table @0x0000008080390000 [ 0.323154] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.324489] Detected PIPT I-cache on CPU5 [ 0.324542] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.324552] GICv3: CPU5: using allocated LPI pending table @0x00000080803a0000 [ 0.324572] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.325966] Detected PIPT I-cache on CPU6 [ 0.326046] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.326056] GICv3: CPU6: using allocated LPI pending table @0x00000080803b0000 [ 0.326086] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.327437] Detected PIPT I-cache on CPU7 [ 0.327497] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.327506] GICv3: CPU7: using allocated LPI pending table @0x00000080803c0000 [ 0.327527] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.327714] smp: Brought up 1 node, 8 CPUs [ 0.507739] SMP: Total of 8 processors activated. [ 0.512539] Callback from call_rcu_tasks_rude() invoked. [ 0.517948] CPU features: detected: 32-bit EL0 Support [ 0.523133] CPU features: detected: 32-bit EL1 Support [ 0.528354] CPU features: detected: CRC32 instructions [ 0.533677] CPU: All CPU(s) started at EL2 [ 0.537821] alternatives: applying system-wide alternatives [ 0.546563] devtmpfs: initialized [ 0.603963] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.613810] futex hash table entries: 2048 (order: 6, 262144 bytes, linear) [ 0.624614] pinctrl core: initialized pinctrl subsystem [ 0.632889] Machine: Freescale Layerscape 2088A RDB Board [ 0.638339] SoC family: QorIQ LS2088A [ 0.642020] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.646920] Callback from call_rcu_tasks() invoked. [ 0.649059] DMI not present or invalid. [ 0.657238] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.665395] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.673006] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.681312] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.689549] audit: initializing netlink subsys (disabled) [ 0.695375] audit: type=2000 audit(0.504:1): state=initialized audit_enabled=0 res=1 [ 0.698917] thermal_sys: Registered thermal governor 'step_wise' [ 0.703202] thermal_sys: Registered thermal governor 'power_allocator' [ 0.709488] cpuidle: using governor menu [ 0.720661] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.727775] ASID allocator initialised with 32768 entries [ 0.738993] Serial: AMBA PL011 UART driver [ 0.796137] KASLR enabled [ 0.848128] HugeTLB: registered 2.00 MiB page size, pre-allocated 256 pages [ 0.855298] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.861619] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.868459] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.874777] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.881616] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.887944] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.894782] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.906813] ACPI: Interpreter disabled. [ 0.917323] iommu: Default domain type: Translated [ 0.922251] iommu: DMA domain TLB invalidation policy: strict mode [ 0.930054] SCSI subsystem initialized [ 0.935295] usbcore: registered new interface driver usbfs [ 0.940993] usbcore: registered new interface driver hub [ 0.946482] usbcore: registered new device driver usb [ 0.953393] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.961424] i2c i2c-0: IMX I2C adapter registered [ 0.967626] pps_core: LinuxPPS API ver. 1 registered [ 0.972631] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.981993] PTP clock support registered [ 0.986347] EDAC MC: Ver: 3.0.0 [ 0.993410] fsl-ifc 2240000.memory-controller: Freescale Integrated Flash Controller [ 1.001309] fsl-ifc 2240000.memory-controller: IFC version 2.0, 8 banks [ 1.011993] FPGA manager framework [ 1.015907] Advanced Linux Sound Architecture Driver Initialized. [ 1.024052] NET: Registered PF_ATMPVC protocol family [ 1.029149] NET: Registered PF_ATMSVC protocol family [ 1.035077] vgaarb: loaded [ 1.038638] clocksource: Switched to clocksource arch_sys_counter [ 1.612597] VFS: Disk quotas dquot_6.6.0 [ 1.616707] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.624572] pnp: PnP ACPI: disabled [ 1.650150] NET: Registered PF_INET protocol family [ 1.655322] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 1.670119] tcp_listen_portaddr_hash hash table entries: 8192 (order: 7, 589824 bytes, linear) [ 1.679743] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.687660] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 1.696391] TCP bind hash table entries: 65536 (order: 11, 9437184 bytes, vmalloc hugepage) [ 1.718545] TCP: Hash tables configured (established 131072 bind 65536) [ 1.726415] MPTCP token hash table entries: 16384 (order: 8, 1441792 bytes, linear) [ 1.736491] UDP hash table entries: 8192 (order: 8, 1310720 bytes, linear) [ 1.745725] UDP-Lite hash table entries: 8192 (order: 8, 1310720 bytes, linear) [ 1.755480] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.762564] RPC: Registered named UNIX socket transport module. [ 1.768568] RPC: Registered udp transport module. [ 1.773313] RPC: Registered tcp transport module. [ 1.778056] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.784559] NET: Registered PF_XDP protocol family [ 1.789403] PCI: CLS 0 bytes, default 64 [ 1.794192] Unpacking initramfs... [ 1.808145] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.816540] kvm [1]: IPA Size Limit: 44 bits [ 1.827176] kvm [1]: vgic-v2@c0e0000 [ 1.830823] kvm [1]: GIC system register CPU interface enabled [ 1.837093] kvm [1]: vgic interrupt IRQ9 [ 1.841413] kvm [1]: Hyp mode initialized successfully [ 1.852907] Initialise system trusted keyrings [ 1.857874] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 1.920913] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.930502] NFS: Registering the id_resolver key type [ 1.935717] Key type id_resolver registered [ 1.939949] Key type id_legacy registered [ 1.944405] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.951174] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.959764] 9p: Installing v9fs 9p2000 file system support [ 1.987664] NET: Registered PF_ALG protocol family [ 1.992553] Key type asymmetric registered [ 1.996699] Asymmetric key parser 'x509' registered [ 2.001806] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 2.009276] io scheduler mq-deadline registered [ 2.013845] io scheduler kyber registered [ 2.018819] test_firmware: interface ready [ 2.059191] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 2.066665] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 2.075336] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 2.084343] layerscape-pcie 3600000.pcie: iATU unroll: disabled [ 2.090313] layerscape-pcie 3600000.pcie: iATU regions: 256 ob, 24 ib, align 4K, limit 4G [ 2.098758] layerscape-pcie 3600000.pcie: PCIe Gen.1 x1 link up [ 2.105158] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 2.111926] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.117463] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.123698] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.134403] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.140485] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 2.146825] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 2.153155] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 2.160406] pci 0000:00:00.0: supports D1 D2 [ 2.164712] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 2.172559] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 2.178747] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 2.185476] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 2.192202] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 2.197882] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 2.204732] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 2.212307] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.230801] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 2.238021] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 2.245224] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 2.252856] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 2.260138] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.266409] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 2.273619] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 2.281249] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 2.288458] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 2.295676] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 2.301854] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.307125] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 2.313274] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 2.321196] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 2.328650] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 2.337283] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 2.345948] layerscape-pcie 3700000.pcie: iATU unroll: disabled [ 2.351932] layerscape-pcie 3700000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G [ 3.077478] Freeing initrd memory: 26612K [ 3.360142] layerscape-pcie 3700000.pcie: Phy link never came up [ 3.366602] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 3.373370] pci_bus 0001:00: root bus resource [bus 00-ff] [ 3.378909] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 3.387946] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 3.398604] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 3.404709] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 3.411938] pci 0001:00:00.0: supports D1 D2 [ 3.416249] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 3.423899] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 3.431544] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 3.440516] EINJ: ACPI disabled. [ 3.508744] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.524479] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 19, base_baud = 21875000) is a 16550A [ 3.535625] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 19, base_baud = 21875000) is a 16550A [ 3.544638] printk: console [ttyS1] enabled [ 3.544638] printk: console [ttyS1] enabled [ 3.553070] printk: bootconsole [uart8250] disabled [ 3.553070] printk: bootconsole [uart8250] disabled [ 3.565010] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 20, base_baud = 21875000) is a 16550A [ 3.575816] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 20, base_baud = 21875000) is a 16550A [ 3.586205] SuperH (H)SCI(F) driver initialized [ 3.592046] msm_serial: driver initialized [ 3.611227] arm-smmu 5000000.iommu: probing hardware configuration... [ 3.617700] arm-smmu 5000000.iommu: SMMUv2 with: [ 3.622328] arm-smmu 5000000.iommu: stage 1 translation [ 3.627649] arm-smmu 5000000.iommu: stage 2 translation [ 3.632969] arm-smmu 5000000.iommu: nested translation [ 3.638203] arm-smmu 5000000.iommu: coherent table walk [ 3.643533] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 3.650694] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 3.657248] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 3.663706] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 3.670158] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 3.679125] arm-smmu 5000000.iommu: preserved 0 boot mappings [ 3.715404] loop: module loaded [ 3.720531] lkdtm: No crash points registered, enable through debugfs [ 3.731054] megasas: 07.719.03.00-rc1 [ 3.738169] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 3.746411] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 3.754055] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 3.762281] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.771265] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.784762] scsi host0: ahci-qoriq [ 3.789509] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 97 [ 3.797865] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 3.805775] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 3.813387] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 3.821477] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.830457] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.842094] scsi host1: ahci-qoriq [ 3.846237] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 98 [ 3.856398] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 3.865712] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 3.875848] Amd/Fujitsu Extended Query Table at 0x0040 [ 3.881015] Amd/Fujitsu Extended Query version 1.3. [ 3.886083] number of CFI chips: 1 [ 3.935645] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 3.942030] nand: Micron MT29F16G08ABABAWP [ 3.946136] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 3.955147] Bad block table found at page 524160, version 0x01 [ 3.963171] Bad block table found at page 524032, version 0x01 [ 4.011296] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 4.023518] spi-nor spi0.0: unrecognized JEDEC id bytes: 70 e1 c3 87 0e 1c [ 4.033208] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 4.059762] thunder_xcv, ver 1.0 [ 4.063183] thunder_bgx, ver 1.0 [ 4.066564] nicpf, ver 1.0 [ 4.113127] ata1: SATA link down (SStatus 0 SControl 300) [ 4.169180] ata2: SATA link down (SStatus 0 SControl 300) [ 5.104272] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 5.111522] hns3: Copyright (c) 2017 Huawei Corporation. [ 5.117109] hclge is initializing [ 5.120527] e1000: Intel(R) PRO/1000 Network Driver [ 5.125415] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 5.131344] e1000e: Intel(R) PRO/1000 Network Driver [ 5.136319] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 5.143143] e1000e 0000:01:00.0: Adding to iommu group 0 [ 5.150326] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 5.207900] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 5.269954] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 5.277940] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 5.284843] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 5.291782] igb: Intel(R) Gigabit Ethernet Network Driver [ 5.297195] igb: Copyright (c) 2007-2014 Intel Corporation. [ 5.302909] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 5.309190] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 5.316150] sky2: driver version 1.30 [ 5.322877] VFIO - User Level meta-driver version: 0.3 [ 5.341452] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.347206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 5.356124] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 5.365653] xhci-hcd xhci-hcd.0.auto: irq 109, io mem 0x03100000 [ 5.372467] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.377993] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 5.385684] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 5.394795] hub 1-0:1.0: USB hub found [ 5.398722] hub 1-0:1.0: 1 port detected [ 5.404215] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.414171] hub 2-0:1.0: USB hub found [ 5.418023] hub 2-0:1.0: 1 port detected [ 5.423299] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.428907] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 5.437721] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 5.447238] xhci-hcd xhci-hcd.1.auto: irq 110, io mem 0x03110000 [ 5.453970] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.459492] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 5.467190] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 5.475450] hub 3-0:1.0: USB hub found [ 5.479302] hub 3-0:1.0: 1 port detected [ 5.484302] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.494075] hub 4-0:1.0: USB hub found [ 5.497923] hub 4-0:1.0: 1 port detected [ 5.504057] usbcore: registered new interface driver usb-storage [ 5.518177] i2c_dev: i2c /dev entries driver [ 5.529717] i2c i2c-0: Added multiplexed i2c bus 1 [ 5.537843] rtc-ds3232 2-0068: oscillator discontinuity flagged, time unreliable [ 5.550575] hwmon hwmon0: temp1_input not attached to any thermal zone [ 5.570664] rtc-ds3232 2-0068: registered as rtc0 [ 5.577721] rtc-ds3232 2-0068: setting system clock to 2022-08-05T05:46:18 UTC (1659678378) [ 5.587357] i2c i2c-0: Added multiplexed i2c bus 2 [ 5.593254] i2c i2c-0: Added multiplexed i2c bus 3 [ 5.599104] i2c i2c-0: Added multiplexed i2c bus 4 [ 5.604589] i2c i2c-0: Added multiplexed i2c bus 5 [ 5.610047] i2c i2c-0: Added multiplexed i2c bus 6 [ 5.615533] i2c i2c-0: Added multiplexed i2c bus 7 [ 5.620985] i2c i2c-0: Added multiplexed i2c bus 8 [ 5.625811] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 5.641796] sp805-wdt c000000.wdt: registration successful [ 5.648168] sp805-wdt c010000.wdt: registration successful [ 5.654464] sp805-wdt c100000.wdt: registration successful [ 5.660751] sp805-wdt c110000.wdt: registration successful [ 5.667060] sp805-wdt c200000.wdt: registration successful [ 5.673352] sp805-wdt c210000.wdt: registration successful [ 5.679645] sp805-wdt c300000.wdt: registration successful [ 5.685931] sp805-wdt c310000.wdt: registration successful [ 5.703529] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 5.718160] sdhci: Secure Digital Host Controller Interface driver [ 5.724372] sdhci: Copyright(c) Pierre Ossman [ 5.730489] Synopsys Designware Multimedia Card Interface Driver [ 5.739447] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.752528] ledtrig-cpu: registered to indicate activity on CPUs [ 5.766113] usbcore: registered new interface driver usbhid [ 5.771708] usbhid: USB HID core driver [ 5.778531] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 5.787068] optee: probing for conduit method. [ 5.791539] optee: api uid mismatch [ 5.795042] optee: probe of firmware:optee failed with error -22 [ 5.807990] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 5.815212] IPv4 over IPsec tunneling driver [ 5.823651] NET: Registered PF_INET6 protocol family [ 5.833606] Segment Routing with IPv6 [ 5.837408] In-situ OAM (IOAM) with IPv6 [ 5.843016] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 5.852167] NET: Registered PF_PACKET protocol family [ 5.858285] 9pnet: Installing 9P2000 support [ 5.862774] Key type dns_resolver registered [ 5.867080] mpls_gso: MPLS GSO support [ 5.879529] registered taskstats version 1 [ 5.883762] Loading compiled-in X.509 certificates [ 5.930798] Loaded X.509 cert 'Build time autogenerated kernel key: 937d274ae268583c2bb06bc0b3d241ebdfb1de04' [ 5.941252] ima: No TPM chip found, activating TPM-bypass! [ 5.946772] ima: Allocated hash algorithm: sha1 [ 5.951430] ima: No architecture policies found [ 5.997217] pcieport 0000:00:00.0: Adding to iommu group 1 [ 6.006177] pcieport 0000:00:00.0: PME: Signaling with IRQ 105 [ 6.013575] pcieport 0000:00:00.0: AER: enabled with IRQ 105 [ 6.021162] pcieport 0001:00:00.0: Adding to iommu group 2 [ 6.029448] pcieport 0001:00:00.0: PME: Signaling with IRQ 113 [ 6.036569] pcieport 0001:00:00.0: AER: enabled with IRQ 113 [ 8.743720] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 8.753004] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.782716] Sending DHCP requests .., OK [ 12.238998] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 12.246651] IP-Config: Complete: [ 12.249885] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 12.259931] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 12.266756] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 12.266770] nameserver0=172.16.1.4 [ 12.282343] ALSA device list: [ 12.285391] No soundcards found. [ 12.325198] Freeing unused kernel memory: 11904K [ 12.330111] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 12.560764] udevd[257]: starting version 3.2.9 [ 14.550822] random: crng init done [ 14.561392] udevd[257]: specified user 'tss' unknown [ 14.566503] udevd[257]: specified group 'tss' unknown [ 14.576852] udevd[258]: starting eudev-3.2.9 [ 15.214422] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) [ 15.224978] fsl_ddr_edac acquired irq 114 for MC [ 15.230084] fsl_ddr_edac MC err registered [ 15.236069] EDAC MC1: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) [ 15.246571] fsl_ddr_edac acquired irq 115 for MC [ 15.251376] fsl_ddr_edac MC err registered [ 15.306777] ftm-alarm 2800000.timer: registered as rtc1 [ 15.364215] arm-ccn 4000000.ccn: No access to interrupts, using timer. [ 15.412627] udevd[266]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 15.421970] udevd[266]: could not rename interface '3' from 'eth0' to 'enp1s0': Device or resource busy [ 15.422705] lm90 4-004c: supply vcc not found, using dummy regulator [ 15.440844] ina2xx 3-0040: error configuring the device: -6 [ 15.454370] hwmon hwmon8: temp1_input not attached to any thermal zone [ 15.461215] hwmon hwmon8: temp2_input not attached to any thermal zone [ 15.571216] mtdblock: MTD device '530000000.flash' is NAND, please consider using UBI block devices instead. done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1242009/environment . /lava-1242009/environment / # /lava-1242009/bin/lava-test-runner /lava-1242009/0 /lava-1242009/bin/lava-test-runner /lava-1242009/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1242009/0/tests/0_dmesg + cat uuid + UUID=1242009_1.5[ 16.531348] .2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 16.609653] [ 16.682924] [ 16.754996] + set +x [ 16.767739] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1242009/environment / # . /lava-1242009/environment/lava-1242009/bin/lava-test-runner /lava-1242009/1 / # /lava-1242009/bin/lava-test-runner /lava-1242009/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1242009/1/tests/1_bootrr + cat uuid + UUID=1242009_1.5[ 17.307557] .2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1242009/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 8000000.crypto /lava-1242009/1/../bin/lava-test-case [ 18.414881] /lava-1242009/1/../bin/lava-test-case [ 18.487174] /lava-1242009/1/../bin/lava-test-case [ 18.526543] + set +x [ 18.564314] / #