Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot 2017.03-imx_v2017.03_4.9.88_2.0.0_ga+gb76bb1b (May 01 2018 - 05:49:44 -0500) CPU: Freescale i.MX7ULP rev2.0 at 500 MHz Reset cause: POR Boot mode: Dual boot Model: NXP i.MX7ULP EVK DRAM: 1 GiB MMC: FSL_SDHC: 0 mmc_init: -95, time 3663 *** Warning - MMC init failed, using default environment No panel detected: default to HX8363_WVGA Display: HX8363_WVGA (480x854) Video: 480x854x24 In: serial Out: serial Err: serial Net: Net Initialization Skipped No ethernet found. Normal Boot Hit any key to stop autoboot: 2  0 => usb start usb start starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 1 Ethernet Device(s) found => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.1.232 (2396 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp ${loadaddr} 1245203/tftp-deploy-wn8mzx6a/kernel/zImage tftp ${loadaddr} 1245203/tftp-deploy-wn8mzx6a/kernel/zImage Using r8152#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.232; sending through gateway 172.16.1.4 Filename '1245203/tftp-deploy-wn8mzx6a/kernel/zImage'. Load address: 0x60800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 3.7 MiB/s done Bytes transferred = 10473984 (9fd200 hex) => tftp ${initrd_addr} 1245203/tftp-deploy-wn8mzx6a/ramdisk/ramdisk.cpio.gz.uboot tftp ${initrd_addr} 1245203/tftp-deploy-wn8mzx6a/ramdisk/ramdisk.cpio.gz.uboot Using r8152#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.232; sending through gateway 172.16.1.4 Filename '1245203/tftp-deploy-wn8mzx6a/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x63800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 3.7 MiB/s done Bytes transferred = 17173627 (1060c7b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp ${fdt_addr} 1245203/tftp-deploy-wn8mzx6a/dtb/imx7ulp-evk.dtb tftp ${fdt_addr} 1245203/tftp-deploy-wn8mzx6a/dtb/imx7ulp-evk.dtb Using r8152#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.232; sending through gateway 172.16.1.4 Filename '1245203/tftp-deploy-wn8mzx6a/dtb/imx7ulp-evk.dtb'. Load address: 0x63000000 Loading: *# 2 MiB/s done Bytes transferred = 10482 (28f2 hex) => setenv bootargs 'console=ttyLP0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyLP0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz ${loadaddr} ${initrd_addr} ${fdt_addr} bootz ${loadaddr} ${initrd_addr} ${fdt_addr} Kernel image @ 0x60800000 [ 0x000000 - 0x9fd200 ] ## Loading init Ramdisk from Legacy Image at 63800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17173563 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 63000000 Booting using the fdt blob at 0x63000000 Using Device Tree in place at 63000000, end 630058f1 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0xf00 [ 0.000000] Linux version 6.1.45-cip3 (KernelCI@build-j18755-arm-gcc-10-multi-v7-defconfig-6qjqz) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 23 10:01:14 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: NXP i.MX7ULP EVK [ 0.000000] earlycon: lpuart32 at MMIO32 0x402d0000 (options '') [ 0.000000] printk: bootconsole [lpuart32] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyLP0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 930704K/1048576K available (14336K kernel code, 2468K rwdata, 6256K rodata, 2048K init, 428K bss, 52336K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000002] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008406] clocksource: imx-tpm: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.020140] Console: colour dummy device 80x30 <6>[ 0.024689] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.035048] CPU: Testing write buffer coherency: ok <6>[ 0.040128] pid_max: default: 32768 minimum: 301 <6>[ 0.045305] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.052640] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <3>[ 0.062150] /cpus/cpu@f00 missing clock-frequency property <6>[ 0.067688] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00 <6>[ 0.075201] Setting up static identity map for 0x60300000 - 0x603000ac <6>[ 0.082595] rcu: Hierarchical SRCU implementation. <6>[ 0.087452] rcu: Max phase no-delay instances is 1000. <6>[ 0.094693] EFI services will not be available. <6>[ 0.099600] smp: Bringing up secondary CPUs ... <6>[ 0.104137] smp: Brought up 1 node, 1 CPU <6>[ 0.108383] SMP: Total of 1 processors activated (6.00 BogoMIPS). <6>[ 0.114753] CPU: All CPU(s) started in SVC mode. <6>[ 0.120444] devtmpfs: initialized <6>[ 0.128331] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.136441] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.146330] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.157244] pinctrl core: initialized pinctrl subsystem <6>[ 0.165683] DMI not present or invalid. <6>[ 0.171260] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.180555] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.190731] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.190890] cpuidle: using governor menu <6>[ 0.217347] No ATAGs? <6>[ 0.219747] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.227942] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.236485] imx7ulp-pinctrl 40ac0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.247784] Serial: AMBA PL011 UART driver <6>[ 2.425971] iommu: Default domain type: Translated <6>[ 2.430955] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 2.438595] SCSI subsystem initialized <6>[ 2.443494] usbcore: registered new interface driver usbfs <6>[ 2.449063] usbcore: registered new interface driver hub <6>[ 2.454669] usbcore: registered new device driver usb <6>[ 2.461653] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.466679] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.476019] PTP clock support registered <6>[ 2.480414] EDAC MC: Ver: 3.0.0 <6>[ 2.487964] vgaarb: loaded <6>[ 2.491474] clocksource: Switched to clocksource imx-tpm <6>[ 2.584135] NET: Registered PF_INET protocol family <6>[ 2.589529] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.601177] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 2.609622] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 2.617562] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.625645] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 2.633368] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.639924] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.646698] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.654232] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 2.661134] RPC: Registered named UNIX socket transport module. <6>[ 2.667150] RPC: Registered udp transport module. <6>[ 2.672045] RPC: Registered tcp transport module. <6>[ 2.676957] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.683675] PCI: CLS 0 bytes, default 64 <5>[ 2.689995] Initialise system trusted keyrings <6>[ 2.695060] Trying to unpack rootfs image as initramfs... <6>[ 2.733054] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.751385] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.794017] NFS: Registering the id_resolver key type <5>[ 2.799186] Key type id_resolver registered <5>[ 2.803623] Key type id_legacy registered <6>[ 2.807949] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.814736] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.822407] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.863636] Key type asymmetric registered <5>[ 2.867767] Asymmetric key parser 'x509' registered <6>[ 2.873311] bounce: pool size: 64 pages <6>[ 2.877359] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 2.884836] io scheduler mq-deadline registered <6>[ 2.889553] io scheduler kyber registered <4>[ 2.939331] gpio gpiochip0: (40ae0000.gpio): not an immutable chip, please consider fixing it! <4>[ 2.983605] gpio gpiochip1: (40af0000.gpio): not an immutable chip, please consider fixing it! <4>[ 3.003177] gpio gpiochip2: (40b00000.gpio): not an immutable chip, please consider fixing it! <4>[ 3.022454] gpio gpiochip3: (40b10000.gpio): not an immutable chip, please consider fixing it! <6>[ 3.266601] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.288033] SuperH (H)SCI(F) driver initialized <6>[ 3.293835] msm_serial: driver initialized <6>[ 3.297945] STMicroelectronics ASC driver initialized <6>[ 3.321897] 402d0000.serial: ttyLP0 at MMIO 0x402d0010 (irq = 46, base_baud = 1500000) is a FSL_LPUART<6>[ 3.331575] printk: console [ttyLP0] enabled <6>[ 3.331575] printk: console [ttyLP0] enabled <6>[ 3.340457] printk: bootconsole [lpuart32] disabled <6>[ 3.340457] printk: bootconsole [lpuart32] disabled <6>[ 3.384306] STM32 USART driver initialized <6>[ 3.446344] brd: module loaded <6>[ 3.472427] loop: module loaded <6>[ 3.492905] CAN device driver interface <6>[ 3.498264] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.505599] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.510835] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.517191] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.522888] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.533708] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 3.539634] usbcore: registered new interface driver pegasus <6>[ 3.545690] usbcore: registered new interface driver asix <6>[ 3.551481] usbcore: registered new interface driver ax88179_178a <6>[ 3.557914] usbcore: registered new interface driver cdc_ether <6>[ 3.564125] usbcore: registered new interface driver smsc75xx <6>[ 3.570204] usbcore: registered new interface driver smsc95xx <6>[ 3.576309] usbcore: registered new interface driver net1080 <6>[ 3.582318] usbcore: registered new interface driver cdc_subset <6>[ 3.588549] usbcore: registered new interface driver zaurus <6>[ 3.594577] usbcore: registered new interface driver cdc_ncm <6>[ 3.606099] usbcore: registered new interface driver usb-storage <6>[ 3.619630] i2c_dev: i2c /dev entries driver <6>[ 3.643948] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.650413] sdhci: Copyright(c) Pierre Ossman <6>[ 3.657465] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.665877] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.902321] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.911716] usbcore: registered new interface driver usbhid <6>[ 3.917572] usbhid: USB HID core driver <6>[ 3.931176] NET: Registered PF_INET6 protocol family <6>[ 3.973957] Segment Routing with IPv6 <6>[ 3.978023] In-situ OAM (IOAM) with IPv6 <6>[ 3.982474] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.989833] NET: Registered PF_PACKET protocol family <6>[ 3.995233] can: controller area network core <6>[ 3.999996] NET: Registered PF_CAN protocol family <6>[ 4.005096] can: raw protocol <6>[ 4.008337] can: broadcast manager protocol <6>[ 4.012826] can: netlink gateway - max_hops=1 <5>[ 4.018047] Key type dns_resolver registered <6>[ 4.023081] ThumbEE CPU extension supported. <5>[ 4.027637] Registering SWP/SWPB emulation handler <5>[ 4.102344] Loading compiled-in X.509 certificates <6>[ 4.192141] ci_hdrc ci_hdrc.0: EHCI Host Controller <6>[ 4.197347] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 <6>[ 4.252280] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 <6>[ 4.273341] hub 1-0:1.0: USB hub found <6>[ 4.277455] hub 1-0:1.0: 1 port detected <6>[ 4.293683] sdhci-esdhc-imx 40370000.mmc: Got CD GPIO <6>[ 4.362128] mmc0: SDHCI controller on 40370000.mmc [40370000.mmc] using ADMA <4>[ 4.532450] mmc0: host does not support reading read-only switch, assuming write-enable <6>[ 4.553828] mmc0: new high speed SDHC card at address e624 <6>[ 4.571874] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.579601] mmcblk0: mmc0:e624 SL16G 14.8 GiB <6>[ 4.594858] mmcblk0: p1 p2 <6>[ 5.873379] Freeing initrd memory: 16772K <6>[ 16.877672] Freeing unused kernel image (initmem) memory: 2048K <6>[ 16.902068] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 17.180310] udevd[87]: starting version 3.2.9 <5>[ 21.941478] random: crng init done <27>[ 21.962182] udevd[87]: specified user 'tss' unknown <27>[ 21.967726] udevd[87]: specified group 'tss' unknown <30>[ 21.979623] udevd[88]: starting eudev-3.2.9 <6>[ 24.727594] caam 40240000.crypto: Entropy delay = 3200 <6>[ 24.778676] caam 40240000.crypto: Instantiated RNG4 SH0 <6>[ 24.824143] caam 40240000.crypto: Instantiated RNG4 SH1 <6>[ 24.829646] caam 40240000.crypto: device ID = 0x0a16030100000000 (Era 9) <6>[ 24.836640] caam 40240000.crypto: job rings = 2, qi = 0 <6>[ 25.731947] usbcore: registered new interface driver r8152 <6>[ 25.741097] usbcore: registered new interface driver r8153_ecm <6>[ 25.941757] usb 1-1: reset high-speed USB device number 2 using ci_hdrc <4>[ 26.172909] r8152 1-1:1.0: Direct firmware load for rtl_nic/rtl8153a-3.fw failed with error -2 <4>[ 26.181927] r8152 1-1:1.0: unable to load firmware patch rtl_nic/rtl8153a-3.fw (-2) <6>[ 26.302003] r8152 1-1:1.0 eth0: v1.12.13 <6>[ 27.180763] caam algorithms registered in /proc/crypto <6>[ 27.188526] caam 40240000.crypto: registering rng-caam <6>[ 27.195864] caam 40240000.crypto: rng crypto API alg registered prng-caam done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1245203/environment . /lava-1245203/environment / # /lava-1245203/bin/lava-test-runner /lava-1245203/0 /lava-1245203/bin/lava-test-runner /lava-1245203/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1245203/0/tests/0_dmesg + cat uuid + UUID=124<8>[ 33.288538] 5203_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 33.365956] <8>[ 33.436728] <8>[ 33.507763] + set +x<8>[ 33.519042] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh / # . /lava-1245203/environment /lava-1245203/bin/lava-test-runner /lava-1245203/1 . /lava-1245203/environment / # /lava-1245203/bin/lava-test-runner /lava-1245203/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1245203/1/tests/1_bootrr + cat uuid + UUID=124<8>[ 39.266571] 5203_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1245203/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight platform: supplier 40250000.pwm not ready /lava-1245203/1/../bin/lava-test-case <8>[ 40.366593] /lava-1245203/1/../bin/lava-test-case <8>[ 40.433620] /lava-1245203/1/../bin/lava-test-case <8>[ 40.472792] + set +x<8>[ 40.500839] / # �