[Enter `^Ec?' for help] G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:F;RCY:0;EMMC:0;READ:0;0. bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:20000703 L2:00008067 L3:14000000 B2:00402000 B1:e0f83180 TE: 208872 BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz Board ID = 8 Set A53 clk to 24M Set A73 clk to 24M Set clk81 to 24M A53 clk: 1200 MHz A73 clk: 1200 MHz CLK81: 166.6M smccc: 000377c6 eMMC boot @ 0 sw8 s DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01 board id: 8 Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0 fw parse done Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0 Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0 PIEI prepare done fastboot data load 00000000 emmc switch 1 ok ddr saved addr:00016000 Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0 00000000 emmc switch 0 ok fastboot data verify verify result: 265 Cfg max: 4, cur: 1. Board id: 255. Force loop cfg LPDDR4 probe ddr clk to 1608MHz Load ddrfw from eMMC, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part: 0 dmc_version 0001 Check phy result INFO : End of CA training INFO : End of initialization INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of Write leveling coarse delay INFO : Training has run successfully! Check phy result INFO : End of initialization INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from eMMC, src: 0x00048200, des: 0xfffd0000, size: 0x0000c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! channel==0 RxClkDly_Margin_A0==97 ps 10 TxDqDly_Margin_A0==97 ps 10 RxClkDly_Margin_A1==87 ps 9 TxDqDly_Margin_A1==106 ps 11 TrainedVREFDQ_A0==28 TrainedVREFDQ_A1==26 VrefDac_Margin_A0==29 DeviceVref_Margin_A0==27 VrefDac_Margin_A1==29 DeviceVref_Margin_A1==26 channel==1 RxClkDly_Margin_A0==97 ps 10 TxDqDly_Margin_A0==106 ps 11 RxClkDly_Margin_A1==97 ps 10 TxDqDly_Margin_A1==106 ps 11 TrainedVREFDQ_A0==25 TrainedVREFDQ_A1==25 VrefDac_Margin_A0==27 DeviceVref_Margin_A0==25 VrefDac_Margin_A1==28 DeviceVref_Margin_A1==25 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004 soc_vref_reg_value 0x 0000002a 00000026 00000028 00000027 00000027 00000028 00000028 00000027 00000027 00000027 00000027 00000028 00000027 00000027 00000026 00000026 00000027 00000026 00000027 00000026 00000025 00000026 00000026 00000027 00000027 00000027 00000026 00000027 00000025 00000027 00000027 00000026 dram_vref_reg_value 0x 00000013 2D training succeed aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19 auto size-- 65535DDR cs0 size: 2048MB DDR cs1 size: 2048MB DMC_DDR_CTRL: 00e00024DDR size: 3928MB cs0 DataBus test pass cs1 DataBus test pass cs0 AddrBus test pass cs1 AddrBus test pass 100bdlr_step_size ps== 431 result report boot times 0Enable ddr reg access 00000000 emmc switch 3 ok Authentication key not yet programmed get rpmb counter error 0x00000007 00000000 emmc switch 0 ok Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0 Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000dc000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 MVN_1=0x00000000 MVN_2=0x00000000 [Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz] OPS=0x10 ring efuse init chipver efuse init 29 0b 10 00 01 26 07 00 00 0a 33 32 4e 31 53 50 [0.018960 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):4fc40b1 NOTICE: BL31: Built : 15:58:17, May 22 2019 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2015.01-g4752efb (Mar 19 2020 - 11:49:51) DRAM: 3.8 GiB Relocation Offset is: d6e22000 spi_post_bind(spifc): req_seq = 0 register usb cfg[0][1] = 00000000d7f28538 aml_i2c_init_port init regs for 0 NAND: get_sys_clk_rate_mtd() 290, clock setting 200! NAND device id: 0 9f ff ff ff ff No NAND device found!!! nand init failed: -6 get_sys_clk_rate_mtd() 290, clock setting 200! NAND device id: 0 9f ff ff ff ff No NAND device found!!! nand init failed: -6 MMC: aml_priv->desc_buf = 0x00000000d3e12a70 aml_priv->desc_buf = 0x00000000d3e14db0 SDIO Port B: 0, SDIO Port C: 1 co-phase 0x3, tx-dly 0, clock 400000 co-phase 0x3, tx-dly 0, clock 400000 co-phase 0x3, tx-dly 0, clock 400000 emmc/sd response timeout, cmd8, status=0x3ff2800 emmc/sd response timeout, cmd55, status=0x3ff2800 co-phase 0x3, tx-dly 0, clock 400000 co-phase 0x1, tx-dly 0, clock 40000000 aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x2000 [mmc_startup] mmc refix success init_part() 297: PART_TYPE_AML [mmc_init] mmc init success start dts,buffer=00000000d3e17620,dt_addr=00000000d3e17620 get_partition_from_dts() 91: ret 0 parts: 17 00: logo 0000000000800000 1 01: recovery 0000000001800000 1 02: misc 0000000000800000 1 03: dtbo 0000000000800000 1 04: cri_data 0000000000800000 2 05: param 0000000001000000 2 06: boot 0000000001000000 1 set has_boot_slot = 0 07: rsv 0000000001000000 1 08: metadata 0000000001000000 1 09: vbmeta 0000000000200000 1 10: tee 0000000002000000 1 11: vendor 0000000014000000 1 12: odm 0000000008000000 1 13: system 0000000050000000 1 14: product 0000000008000000 1 15: cache 0000000046000000 2 16: data ffffffffffffffff 4 init_part() 297: PART_TYPE_AML eMMC/TSD partition table have been checked OK! crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!! crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!! crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!! mmc env offset: 0x4d400000 In: serial Out: serial Err: serial reboot_mode=cold_boot [store]To run cmd[emmc dtb_read 0x1000000 0x40000] _verify_dtb_checksum()-3477: calc 2dfddccd, store 2dfddccd _verify_dtb_checksum()-3477: calc 2dfddccd, store 2dfddccd dtb_read()-3694: total valid 2 update_old_dtb()-3675: do nothing aml_i2c_init_port init regs for 0 fusb302_init: Device ID: 0x91 CC connected in 0 as UFP charge ic max_vol = 12000mv max_cur = 6000ma chip->pos_power = 3, chip->pd_output_vol=12000 chip->pd_output_cur=2000 fusb302 detect chip.port_num = 0 amlkey_init() enter! [EFUSE_MSG]keynum is 1 vpu: clk_level in dts: 7 vpu: vpu_power_on vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100) vpu: vpu_module_init_config vpp: vpp_init vpp: vpp osd2 matrix rgb2yuv.............. cvbs: cpuid:0x29 LCD_RESET PIN: 0 lcd: detect mode: tablet, key_valid: 0 lcd: detect lcd_clk_path: 1 lcd: failed to get lcd_cpu_gpio_names lcd: load config from dts lcd: pinctrl_version: 2 lcd: use panel_type=lcd_1 lcd: bl: pinctrl_version: 2 lcd: bl: name: backlight_pwm, method: 1 lcd: bl: pwm_reg=0x00800002 lcd: error: gpio: wrong name invalid lcd: bl: aml_bl_power_ctrl: 0 Net: dwmac.ff3f0000amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 1 MACADDR:02:00:00:07:26:01(from chipid) CONFIG_AVB2: null Start read misc partition datas! info->magic = info->version_major = 1 info->version_minor = 0 info->slots[0].priority = 15 info->slots[0].tries_remaining = 7 info->slots[0].successful_boot = 0 info->slots[1].priority = 14 info->slots[1].tries_remaining = 7 info->slots[1].successful_boot = 0 info->crc32 = -1075449479 active slot = 0 wipe_data=successful wipe_cache=successful upgrade_step=2 reboot_mode:::: cold_boot lcd: error: outputmode[576cvbs] is not support hpd_state=0 edid preferred_mode is [0] hdr mode is 0 dv mode is ver:0 len: 0 hdr10+ mode is 0 [OSD]load fb addr from dts:/meson-fb [OSD]set initrd_high: 0x7f800000 [OSD]fb_addr for logo: 0x7f800000 [OSD]load fb addr from dts:/meson-fb [OSD]fb_addr for logo: 0x7f800000 [OSD]VPP_OFIFO_SIZE:0xfff01fff [CANVAS]canvas init [CANVAS]addr=0x7f800000 width=3840, height=2160 [OSD]osd_hw.free_dst_data: 0,719,0,575 [OSD]osd1_update_disp_freescale_enable vpp: vpp_matrix_update: 2 cvbs performance type = 9, table = 0 cvbs_config_hdmipll_g12a cvbs_set_vid2_clk vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0 normal power on boot wol: disable saradc: 0x289, hw_ver: 0x32 (VIM3.V12) gpio: pin GPIOAO_7 (gpio 7) value is 1 port mode is usb3.0 Command: bcb uboot-command Start read misc partition datas! BCB hasn't any datas,exit! Hit Enter or space or Ctrl+C key to stop autoboot -- : 1  0 kvim3#setenv autoload no setenv autoload no kvim3#setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff kvim3#setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff kvim3#dhcp dhcp dwmac.ff3f0000 Waiting for PHY auto negotiation to complete.... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 *** WARNING: Host Name is too long (34 - max: 32) - truncated *** WARNING: Host Name is too long (34 - max: 32) - truncated DHCP client bound to address 192.168.201.18 (772 ms) kvim3#setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 kvim3#tftp 0x01080000 11470976/tftp-deploy-zzt45yon/kernel/uImage tftp 0x01080000 11470976/tftp-deploy-zzt45yon/kernel/uImage Speed: 1000, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.18 Filename '11470976/tftp-deploy-zzt45yon/kernel/uImage'. Load address: 0x1080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 18.6 MiB/s done Bytes transferred = 53314112 (32d8240 hex) kvim3#tftp 0x08000000 11470976/tftp-deploy-zzt45yon/ramdisk/ramdisk.cpio.gz.uboot tftp 0x08000000 11470976/tftp-deploy-zzt45yon/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.18 Filename '11470976/tftp-deploy-zzt45yon/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x8000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################## 6 MiB/s done Bytes transferred = 27087280 (19d51b0 hex) kvim3#setenv initrd_size ${filesize} setenv initrd_size ${filesize} kvim3#tftp 0x01070000 11470976/tftp-deploy-zzt45yon/dtb/meson-g12b-a311d-khadas-vim3.dtb tftp 0x01070000 11470976/tftp-deploy-zzt45yon/dtb/meson-g12b-a311d-khadas-vim3.dtb Speed: 1000, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.18 Filename '11470976/tftp-deploy-zzt45yon/dtb/meson-g12b-a311d-khadas-vim3.dtb'. Load address: 0x1070000 Loading: *#### 6.2 MiB/s done Bytes transferred = 52193 (cbe1 hex) kvim3#setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' kvim3#bootm 0x01080000 0x08000000 0x01070000 bootm 0x01080000 0x08000000 0x01070000 avb2: 0 ee_gate_off ... avb2: 0 ## Booting kernel from Legacy Image at 01080000 ... Image Name: Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 53314048 Bytes = 50.8 MiB Load Address: 01080000 Entry Point: 01080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 08000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 27087216 Bytes = 25.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Start read misc partition datas! info->magic = info->version_major = 1 info->version_minor = 0 info->slots[0].priority = 15 info->slots[0].tries_remaining = 7 info->slots[0].successful_boot = 0 info->slots[1].priority = 14 info->slots[1].tries_remaining = 7 info->slots[1].successful_boot = 0 info->crc32 = -1075449479 active slot = 0 active_slot is normal load dtb from 0x1000000 ...... ## Flattened Device Tree blob at 01070000 Booting using the fdt blob at 0x1070000 find 1 dtbos No androidboot.dtbo_idx configured And no dtbos will be applied Loading Kernel Image(COMP_NONE) ... OK kernel loaded at 0x01080000, end = 0x04358200 libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND [rsvmem] fdt get prop fail. Loading Ramdisk to d243b000, end d3e10170 ... OK Loading Device Tree to 00000000d242b000, end 00000000d243abe0 ... OK Starting kernel ... uboot time: 14897330 us [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.1.52-cip5 (KernelCI@build-j38865-arm64-gcc-10-defconfig-kselftest-6bknz) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Fri Sep 8 12:46:25 UTC 2023 [ 0.000000] Machine model: Khadas VIM3 [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000dd800000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8') [ 0.000000] printk: bootconsole [meson0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x00000000ed7fffff] [ 0.000000] NUMA: NODE_DATA [mem 0xdd03b640-0xdd03dfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ed7fffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff] [ 0.000000] node 0: [mem 0x0000000005000000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x00000000ed7fffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000ed7fffff] [ 0.000000] On node 0, zone DMA: 10240 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 31 pages/cpu s89696 r8192 d29088 u126976 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 957600 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Memory: 3424760K/3891200K available (22080K kernel code, 5920K rwdata, 11892K rodata, 12032K init, 11464K bss, 204296K reserved, 262144K cma-reserved) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 <6>[ 0.000000] ftrace: allocating 66397 entries in 260 pages <6>[ 0.000000] ftrace: allocated 260 pages with 2 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009389] Console: colour dummy device 80x25 <4>[ 0.013040] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.021118] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.025475] ... MAX_LOCK_DEPTH: 48 <4>[ 0.029937] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.034574] ... CLASSHASH_SIZE: 4096 <4>[ 0.039212] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.043937] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.048662] ... CHAINHASH_SIZE: 32768 <4>[ 0.053387] memory used by lock dependency info: 6365 kB <4>[ 0.059074] memory used for stack traces: 4224 kB <4>[ 0.064149] per task-struct memory footprint: 1920 bytes <6>[ 0.070075] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.080435] pid_max: default: 32768 minimum: 301 <6>[ 0.085969] LSM: Security Framework initializing <6>[ 0.090396] landlock: Up and running. <6>[ 0.094208] LSM support for eBPF active <6>[ 0.098847] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.105995] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.126984] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.128867] cblist_init_generic: Setting shift to 3 and lim to 1. <6>[ 0.135909] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.142889] cblist_init_generic: Setting shift to 3 and lim to 1. <6>[ 0.149762] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.156798] cblist_init_generic: Setting shift to 3 and lim to 1. <6>[ 0.163646] Running RCU-tasks wait API self tests <6>[ 0.274431] rcu: Hierarchical SRCU implementation. <6>[ 0.274488] rcu: Max phase no-delay instances is 1000. <6>[ 0.283705] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.300493] EFI services will not be available. <6>[ 0.302889] smp: Bringing up secondary CPUs ... <6>[ 0.308494] Detected VIPT I-cache on CPU1 <6>[ 0.308699] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.313120] CPU features: detected: Spectre-v2 <6>[ 0.313136] CPU features: detected: Spectre-v4 <6>[ 0.313141] CPU features: detected: Spectre-BHB <6>[ 0.313146] CPU features: detected: ARM erratum 858921 <6>[ 0.313154] Detected VIPT I-cache on CPU2 <6>[ 0.313267] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.313292] arch_timer: CPU2: Trapping CNTVCT access <6>[ 0.313309] CPU2: Booted secondary processor 0x0000000100 [0x410fd092] <6>[ 0.316841] Detected VIPT I-cache on CPU3 <6>[ 0.316921] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.316936] arch_timer: CPU3: Trapping CNTVCT access <6>[ 0.316949] CPU3: Booted secondary processor 0x0000000101 [0x410fd092] <6>[ 0.320455] Detected VIPT I-cache on CPU4 <6>[ 0.320541] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.320556] arch_timer: CPU4: Trapping CNTVCT access <6>[ 0.320568] CPU4: Booted secondary processor 0x0000000102 [0x410fd092] <6>[ 0.323969] Detected VIPT I-cache on CPU5 <6>[ 0.324059] arch_timer: Enabling local workaround for ARM erratum 858921 <6>[ 0.324074] arch_timer: CPU5: Trapping CNTVCT access <6>[ 0.324087] CPU5: Booted secondary processor 0x0000000103 [0x410fd092] <6>[ 0.324427] smp: Brought up 1 node, 6 CPUs <6>[ 0.449865] SMP: Total of 6 processors activated. <6>[ 0.452554] Callback from call_rcu_tasks_rude() invoked. <6>[ 0.458150] CPU features: detected: 32-bit EL0 Support <6>[ 0.463468] CPU features: detected: 32-bit EL1 Support <6>[ 0.468988] CPU features: detected: CRC32 instructions <6>[ 0.474612] CPU: All CPU(s) started at EL2 <6>[ 0.478802] alternatives: applying system-wide alternatives <6>[ 0.491852] devtmpfs: initialized <6>[ 0.561120] Callback from call_rcu_tasks() invoked. <6>[ 0.586551] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.591015] futex hash table entries: 2048 (order: 6, 262144 bytes, linear) <6>[ 0.654918] pinctrl core: initialized pinctrl subsystem <6>[ 0.664409] DMI not present or invalid. <6>[ 0.666862] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.673565] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.676874] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.685291] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.692984] audit: initializing netlink subsys (disabled) <5>[ 0.699154] audit: type=2000 audit(0.588:1): state=initialized audit_enabled=0 res=1 <6>[ 0.705414] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.706466] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.713139] cpuidle: using governor menu <6>[ 0.724837] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.731224] ASID allocator initialised with 32768 entries <6>[ 0.746412] Serial: AMBA PL011 UART driver <6>[ 0.779114] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /soc/vpu@ff900000 <6>[ 0.914726] platform ff600000.hdmi-tx: Fixed dependency cycle(s) with /hdmi-connector <6>[ 0.928162] KASLR enabled <6>[ 0.997591] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.999024] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 1.005622] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 1.012688] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 1.019250] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 1.026334] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 1.032899] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 1.039984] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 1.056306] ACPI: Interpreter disabled. <6>[ 1.074259] iommu: Default domain type: Translated <6>[ 1.074305] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 1.082698] SCSI subsystem initialized <6>[ 1.086807] usbcore: registered new interface driver usbfs <6>[ 1.090427] usbcore: registered new interface driver hub <6>[ 1.095947] usbcore: registered new device driver usb <6>[ 1.106378] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.106414] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.115887] PTP clock support registered <6>[ 1.120786] EDAC MC: Ver: 3.0.0 <6>[ 1.132496] FPGA manager framework <6>[ 1.133325] Advanced Linux Sound Architecture Driver Initialized. <6>[ 1.140135] NET: Registered PF_ATMPVC protocol family <6>[ 1.142257] NET: Registered PF_ATMSVC protocol family <6>[ 1.149218] vgaarb: loaded <6>[ 1.152006] clocksource: Switched to clocksource arch_sys_counter <5>[ 1.159963] VFS: Disk quotas dquot_6.6.0 <6>[ 1.161317] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 1.169769] pnp: PnP ACPI: disabled <6>[ 1.207732] NET: Registered PF_INET protocol family <6>[ 1.208169] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.219735] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 147456 bytes, linear) <6>[ 1.224318] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.232055] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.240448] TCP bind hash table entries: 32768 (order: 10, 4718592 bytes, vmalloc hugepage) <6>[ 1.254920] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.257327] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.264610] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.271568] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.279598] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.286845] RPC: Registered named UNIX socket transport module. <6>[ 1.290698] RPC: Registered udp transport module. <6>[ 1.295659] RPC: Registered tcp transport module. <6>[ 1.300644] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.307396] NET: Registered PF_XDP protocol family <6>[ 1.312475] PCI: CLS 0 bytes, default 64 <6>[ 1.318117] Unpacking initramfs... <6>[ 1.329603] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.338804] kvm [1]: vgic interrupt IRQ9 <6>[ 1.339263] kvm [1]: Hyp mode initialized successfully <5>[ 1.351765] Initialise system trusted keyrings <6>[ 1.352804] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.440038] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.446456] NFS: Registering the id_resolver key type <5>[ 1.446612] Key type id_resolver registered <5>[ 1.450688] Key type id_legacy registered <6>[ 1.455626] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.462024] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.471579] 9p: Installing v9fs 9p2000 file system support <6>[ 1.505529] NET: Registered PF_ALG protocol family <5>[ 1.505738] Key type asymmetric registered <5>[ 1.509413] Asymmetric key parser 'x509' registered <6>[ 1.514837] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.522302] io scheduler mq-deadline registered <6>[ 1.527033] io scheduler kyber registered <4>[ 1.532792] test_firmware: interface ready <6>[ 1.548789] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized <6>[ 1.644022] EINJ: ACPI disabled. <6>[ 1.761842] soc soc0: Amlogic Meson G12B (A311D) Revision 29:b (10:2) Detected <6>[ 1.809468] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.826647] SuperH (H)SCI(F) d<6>[ 1.829955] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart <6>[ 1.840096] printk: console [ttyAML0] enabled <6>[ 1.840096] printk: console [ttyAML0] enabled <6>[ 1.843679] printk: bootconsole [meson0] disabled <6>[ 1.843679] printk: bootconsole [meson0] disabled <6>[ 1.857229] ffd24000.serial: ttyAML6 at MMIO 0xffd24000 (irq = 15, base_baud = 1500000) is a meson_uart <6>[ 1.864019] serial serial0: tty port ttyAML6 registered <6>[ 1.870532] msm_serial: driver initialized <6>[ 1.926295] loop: module loaded <6>[ 1.929180] lkdtm: No crash points registered, enable through debugfs <6>[ 1.938596] megasas: 07.719.03.00-rc1 <6>[ 1.990823] thunder_xcv, ver 1.0 <6>[ 1.991119] thunder_bgx, ver 1.0 <6>[ 1.992411] nicpf, ver 1.0 <6>[ 2.003243] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 2.005120] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 2.011085] hclge is initializing <6>[ 2.014303] e1000: Intel(R) PRO/1000 Network Driver <6>[ 2.019256] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 2.025519] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 2.030384] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.037024] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 2.042145] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.048177] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 2.054360] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 2.062800] sky2: driver version 1.30 <6>[ 2.071314] VFIO - User Level meta-driver version: 0.3 <6>[ 2.091805] usbcore: registered new interface driver usb-storage <6>[ 2.110376] i2c_dev: i2c /dev entries driver <6>[ 2.165196] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.166004] sdhci: Copyright(c) Pierre Ossman <6>[ 2.174862] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.183081] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.187441] meson-gx-mmc ffe05000.sd: Got CD GPIO <6>[ 2.197161] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.204352] meson-sm: secure-monitor enabled <6>[ 2.212474] usbcore: registered new interface driver usbhid <6>[ 2.212682] usbhid: USB HID core driver <6>[ 2.256058] netem: version 1.3 <6>[ 2.258598] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.261870] IPv4 over IPsec tunneling driver <6>[ 2.270343] NET: Registered PF_INET6 protocol family <6>[ 2.277987] Segment Routing with IPv6 <6>[ 2.278180] In-situ OAM (IOAM) with IPv6 <6>[ 2.283963] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.291606] NET: Registered PF_PACKET protocol family <6>[ 2.293435] 9pnet: Installing 9P2000 support <5>[ 2.296709] Key type dns_resolver registered <6>[ 2.300830] mpls_gso: MPLS GSO support <6>[ 2.316276] registered taskstats version 1 <5>[ 2.316461] Loading compiled-in X.509 certificates <6>[ 3.410317] Freeing initrd memory: 26452K <5>[ 3.488748] Loaded X.509 cert 'Build time autogenerated kernel key: 55b7ac01abd932f20e26e4c9ffc5f0dbc25113c0' <6>[ 3.494207] ima: No TPM chip found, activating TPM-bypass! <6>[ 3.499015] ima: Allocated hash algorithm: sha1 <6>[ 3.503900] ima: No architecture policies found <6>[ 3.754027] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2 <6>[ 3.754109] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1 <4>[ 3.770379] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator <4>[ 3.773286] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator <6>[ 3.781027] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM <6>[ 3.798827] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.799347] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 3.808901] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010 <6>[ 3.816690] xhci-hcd xhci-hcd.0.auto: irq 19, io mem 0xff500000 <6>[ 3.824035] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 3.828271] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 3.836136] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 3.847736] hub 1-0:1.0: USB hub found <6>[ 3.848107] hub 1-0:1.0: 2 ports detected <6>[ 3.854501] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 3.862758] hub 2-0:1.0: USB hub found <6>[ 3.863355] hub 2-0:1.0: 1 port detected <6>[ 3.871702] pca953x 0-0020: using no AI <6>[ 3.902091] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq <6>[ 4.112053] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.205216] mmc1: new HS200 MMC card at address 0001 <6>[ 4.210876] mmcblk1: mmc1:0001 BJTD4R 29.1 GiB <6>[ 4.228386] mmcblk1boot0: mmc1:0001 BJTD4R 4.00 MiB <6>[ 4.241880] mmcblk1boot1: mmc1:0001 BJTD4R 4.00 MiB <6>[ 4.252926] mmcblk1rpmb: mmc1:0001 BJTD4R 4.00 MiB, chardev (511:0) <6>[ 4.324165] hub 1-1:1.0: USB hub found <6>[ 4.324423] hub 1-1:1.0: 4 ports detected <6>[ 23.952040] Waiting up to 100 more seconds for network. <6>[ 43.956059] Waiting up to 80 more seconds for network. <6>[ 63.960030] Waiting up to 60 more seconds for network. <6>[ 64.615372] platform wifi32k: deferred probe pending <6>[ 64.615474] platform regulator-vddcpu-a: deferred probe pending <6>[ 64.621210] platform regulator-vddcpu-b: deferred probe pending <6>[ 64.627292] platform cpufreq-dt: deferred probe pending <6>[ 64.632724] platform sdio-pwrseq: deferred probe pending <6>[ 83.964057] Waiting up to 40 more seconds for network. <6>[ 103.968057] Waiting up to 20 more seconds for network. <5>[ 123.980060] Sending DHCP requests ...... timed out! <3>[ 204.535894] IP-Config: Reopening network devices... <6>[ 224.540058] Waiting up to 100 more seconds for network. <6>[ 244.544056] Waiting up to 80 more seconds for network. <6>[ 264.548057] Waiting up to 60 more seconds for network.