[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.22 (762 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 12682891/tftp-deploy-yppge_w4/kernel/zImage tftp 0x2000000 12682891/tftp-deploy-yppge_w4/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12682891/tftp-deploy-yppge_w4/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 3.5 MiB/s done Bytes transferred = 10519040 (a08200 hex) => tftp 0x4000000 12682891/tftp-deploy-yppge_w4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 12682891/tftp-deploy-yppge_w4/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12682891/tftp-deploy-yppge_w4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 3.6 MiB/s done Bytes transferred = 17156808 (105cac8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 12682891/tftp-deploy-yppge_w4/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 12682891/tftp-deploy-yppge_w4/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '12682891/tftp-deploy-yppge_w4/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 3.3 MiB/s done Bytes transferred = 41716 (a2f4 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0xa08200 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17156744 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0d2f3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 6.1.72-cip13 (KernelCI@build-j94737-arm-gcc-10-multi-v7-defconfig-4xd68) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Feb 1 13:36:28 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Radxa Rock 2 Square [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1970772K/2097152K available (14336K kernel code, 2469K rwdata, 6208K rodata, 2048K init, 428K bss, 60844K reserved, 65536K cma-reserved, 1245184K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009083] Switching to timer-based delay loop, resolution 41ns <6>[ 0.023711] Console: colour dummy device 80x30 <6>[ 0.028926] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.040599] CPU: Testing write buffer coherency: ok <6>[ 0.046278] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.052123] pid_max: default: 32768 minimum: 301 <6>[ 0.057654] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.065994] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.075740] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 <6>[ 0.083351] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.092549] rcu: Hierarchical SRCU implementation. <6>[ 0.098096] rcu: Max phase no-delay instances is 1000. <6>[ 0.109122] EFI services will not be available. <6>[ 0.114745] smp: Bringing up secondary CPUs ... <6>[ 0.121812] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 <6>[ 0.121831] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.136131] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 <6>[ 0.136149] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.150386] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 <6>[ 0.150406] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.162861] smp: Brought up 1 node, 4 CPUs <6>[ 0.167678] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.174847] CPU: All CPU(s) started in SVC mode. <6>[ 0.180854] devtmpfs: initialized <6>[ 0.194551] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 <6>[ 0.203515] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214631] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.224442] pinctrl core: initialized pinctrl subsystem <6>[ 0.234492] DMI not present or invalid. <6>[ 0.239826] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.249004] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.259905] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.259975] cpuidle: using governor menu <6>[ 0.272137] No ATAGs? <6>[ 0.275055] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.284161] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.294457] Serial: AMBA PL011 UART driver <6>[ 0.323677] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff940000/port/endpoint@0 <6>[ 0.333664] platform ff980000.hdmi: Fixed dependency cycle(s) with /vop@ff930000/port/endpoint@0 <6>[ 0.359344] rockchip-gpio ff750000.gpio: probed /pinctrl/gpio@ff750000 <6>[ 0.367574] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000 <6>[ 0.375743] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000 <6>[ 0.383942] rockchip-gpio ff7a0000.gpio: probed /pinctrl/gpio@ff7a0000 <6>[ 0.392204] rockchip-gpio ff7b0000.gpio: probed /pinctrl/gpio@ff7b0000 <6>[ 0.400398] rockchip-gpio ff7c0000.gpio: probed /pinctrl/gpio@ff7c0000 <6>[ 0.408572] rockchip-gpio ff7d0000.gpio: probed /pinctrl/gpio@ff7d0000 <6>[ 0.416786] rockchip-gpio ff7e0000.gpio: probed /pinctrl/gpio@ff7e0000 <6>[ 0.424951] rockchip-gpio ff7f0000.gpio: probed /pinctrl/gpio@ff7f0000 <6>[ 0.465094] iommu: Default domain type: Translated <6>[ 0.470740] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.478836] SCSI subsystem initialized <6>[ 0.483766] usbcore: registered new interface driver usbfs <6>[ 0.490178] usbcore: registered new interface driver hub <6>[ 0.496340] usbcore: registered new device driver usb <6>[ 0.504903] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.510640] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.520991] PTP clock support registered <6>[ 0.525856] EDAC MC: Ver: 3.0.0 <6>[ 0.533405] vgaarb: loaded <6>[ 0.541335] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.560676] NET: Registered PF_INET protocol family <6>[ 0.566596] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.577290] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.586792] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.595610] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.604484] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.613090] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.620449] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.628063] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.636298] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.643307] RPC: Registered named UNIX socket transport module. <6>[ 0.650097] RPC: Registered udp transport module. <6>[ 0.655573] RPC: Registered tcp transport module. <6>[ 0.661022] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.668393] PCI: CLS 0 bytes, default 64 <6>[ 0.673603] Trying to unpack rootfs image as initramfs... <6>[ 0.685081] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available <5>[ 0.696259] Initialise system trusted keyrings <6>[ 0.701730] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 0.716083] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.723603] NFS: Registering the id_resolver key type <5>[ 0.729476] Key type id_resolver registered <5>[ 0.734408] Key type id_legacy registered <6>[ 0.739216] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.746898] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.755363] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.761504] Key type asymmetric registered <5>[ 0.766293] Asymmetric key parser 'x509' registered <6>[ 0.772133] bounce: pool size: 64 pages <6>[ 0.776775] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 0.785206] io scheduler mq-deadline registered <6>[ 0.790467] io scheduler kyber registered <6>[ 0.869706] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 0.878370] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 <6>[ 0.903045] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 0.911689] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 <6>[ 1.004947] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.015579] printk: console [ttyS2] disabled <6>[ 1.020630] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 47, base_baud = 1500000) is a 16550A <6>[ 1.030854] printk: console [ttyS2] enabled <6>[ 1.030854] printk: console [ttyS2] enabled <6>[ 1.040827] printk: bootconsole [uart0] disabled <6>[ 1.040827] printk: bootconsole [uart0] disabled <6>[ 1.055585] SuperH (H)SCI(F) driver initialized <6>[ 1.062813] msm_serial: driver initialized <6>[ 1.067681] STMicroelectronics ASC driver initialized <6>[ 1.075594] STM32 USART driver initialized <6>[ 1.106933] brd: module loaded <6>[ 1.117654] loop: module loaded <6>[ 1.140211] CAN device driver interface <6>[ 1.146956] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.155731] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.161599] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.168586] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.174935] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.189711] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.196319] usbcore: registered new interface driver pegasus <6>[ 1.203019] usbcore: registered new interface driver asix <6>[ 1.209410] usbcore: registered new interface driver ax88179_178a <6>[ 1.216595] usbcore: registered new interface driver cdc_ether <6>[ 1.223489] usbcore: registered new interface driver smsc75xx <6>[ 1.230263] usbcore: registered new interface driver smsc95xx <6>[ 1.237074] usbcore: registered new interface driver net1080 <6>[ 1.243770] usbcore: registered new interface driver cdc_subset <6>[ 1.250736] usbcore: registered new interface driver zaurus <6>[ 1.257378] usbcore: registered new interface driver cdc_ncm <4>[ 1.267574] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.276033] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.363040] dwc2 ff540000.usb: DWC OTG Controller <6>[ 1.368630] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 <6>[ 1.376877] dwc2 ff540000.usb: irq 51, io mem 0xff540000 <6>[ 1.384004] hub 1-0:1.0: USB hub found <6>[ 1.388543] hub 1-0:1.0: 1 port detected <4>[ 1.394017] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.402467] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.541410] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM <6>[ 1.570053] dwc2 ff580000.usb: DWC OTG Controller <6>[ 1.575674] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.583901] dwc2 ff580000.usb: irq 52, io mem 0xff580000 <6>[ 1.590944] hub 2-0:1.0: USB hub found <6>[ 1.595503] hub 2-0:1.0: 1 port detected <6>[ 1.602911] ehci-platform ff500000.usb: EHCI Host Controller <6>[ 1.605955] usbcore: registered new interface driver usb-storage <6>[ 1.609564] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3 <6>[ 1.625786] i2c_dev: i2c /dev entries driver <6>[ 1.635456] i2c 0-005a: Fixed dependency cycle(s) with /i2c@ff650000/act8846@5a/regulators/REG4 <6>[ 1.645627] i2c 0-005a: Fixed dependency cycle(s) with /i2c@ff650000/act8846@5a/regulators/REG2 <6>[ 1.660132] VDD_LOG: Bringing 1100000uV into 1000000-1000000uV <6>[ 1.665073] ehci-platform ff500000.usb: irq 53, io mem 0xff500000 <6>[ 1.693438] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! <6>[ 1.701349] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 <6>[ 1.706119] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! <6>[ 1.717156] hub 3-0:1.0: USB hub found <6>[ 1.721722] hub 3-0:1.0: 1 port detected <4>[ 1.739554] dw_wdt ff800000.watchdog: No valid TOPs array specified <6>[ 1.758017] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz <6>[ 1.773598] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.780815] sdhci: Copyright(c) Pierre Ossman <6>[ 1.788869] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.797293] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 1.798450] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.817105] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 1.824832] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 1.831387] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 1.844032] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.851984] usbcore: registered new interface driver usbhid <6>[ 1.858504] usbhid: USB HID core driver <6>[ 1.866589] NET: Registered PF_INET6 protocol family <6>[ 1.872941] Segment Routing with IPv6 <6>[ 1.877354] In-situ OAM (IOAM) with IPv6 <6>[ 1.882088] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 1.889295] NET: Registered PF_PACKET protocol family <6>[ 1.895257] can: controller area network core <6>[ 1.900459] NET: Registered PF_CAN protocol family <6>[ 1.906142] can: raw protocol <6>[ 1.909751] can: broadcast manager protocol <6>[ 1.914742] can: netlink gateway - max_hops=1 <5>[ 1.920108] Key type dns_resolver registered <6>[ 1.925243] ThumbEE CPU extension supported. <5>[ 1.930309] Registering SWP/SWPB emulation handler <5>[ 1.936283] Loading compiled-in X.509 certificates <6>[ 1.962999] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 1.970252] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 1.977857] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). <6>[ 1.986049] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). <6>[ 1.987920] Freeing initrd memory: 16756K <6>[ 1.992671] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). <6>[ 2.004049] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). <6>[ 2.011265] rk_gmac-dwmac ff290000.ethernet: clock input from PHY <6>[ 2.023375] rk_gmac-dwmac ff290000.ethernet: init for RGMII <6>[ 2.029948] usb 3-1: new high-speed USB device number 2 using ehci-platform <6>[ 2.038123] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 <6>[ 2.046400] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 <6>[ 2.052530] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported <6>[ 2.061182] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported <6>[ 2.069836] rk_gmac-dwmac ff290000.ethernet: COE Type 2 <6>[ 2.075966] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported <6>[ 2.084133] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported <6>[ 2.091654] rk_gmac-dwmac ff290000.ethernet: Normal descriptors <6>[ 2.098555] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled <6>[ 2.105364] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 2.249731] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) <6>[ 2.261331] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) <6>[ 2.277914] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.279451] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.280911] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.286770] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 2.310512] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.318217] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.323171] hub 3-1:1.0: USB hub found <6>[ 2.324756] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.329495] hub 3-1:1.0: 4 ports detected <6>[ 2.340292] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. <6>[ 2.352659] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a <6>[ 2.359206] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 62,32 bit host data width,256 deep fifo <6>[ 2.370382] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. <6>[ 2.377923] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.378087] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a <6>[ 2.392778] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 63,32 bit host data width,256 deep fifo <6>[ 2.403852] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.404188] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 2.411545] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.422260] dwmmc_rockchip ff0f0000.mmc: allocated mmc-pwrseq <6>[ 2.428651] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.435367] mmc_host mmc0: card is non-removable. <6>[ 2.450789] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.460136] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.467829] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.474377] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.500244] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 2.525848] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.526064] rk_gmac-dwmac ff290000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 <6>[ 2.544175] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.545101] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 2.551873] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.570158] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 2.571320] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found <6>[ 2.589899] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW <6>[ 2.597963] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 2.604719] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 2.619315] mmc0: new high speed MMC card at address 0001 <6>[ 2.626066] mmcblk0: mmc0:0001 032GE4 29.1 GiB <6>[ 2.634870] mmcblk0: p1 p2 <6>[ 2.638783] mmcblk0boot0: mmc0:0001 032GE4 4.00 MiB <6>[ 2.645567] mmcblk0boot1: mmc0:0001 032GE4 4.00 MiB <6>[ 2.652197] mmcblk0rpmb: mmc0:0001 032GE4 4.00 MiB, chardev (236:0) <6>[ 2.662443] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 2.670680] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 2.678375] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 2.684915] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 5.712699] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 5.722629] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.751779] Sending DHCP requests .., OK <6>[ 8.516368] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.22 <6>[ 8.525809] IP-Config: Complete: <6>[ 8.529748] device=eth0, hwaddr=4a:01:9c:e5:04:ff, ipaddr=192.168.201.22, mask=255.255.255.0, gw=192.168.201.1 <6>[ 8.541909] host=rk3288-rock2-square-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 8.550914] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 8.550959] nameserver0=192.168.201.1 <4>[ 8.568011] dw-apb-uart ff690000.serial: forbid DMA for kernel console <6>[ 8.589465] Freeing unused kernel image (initmem) memory: 2048K <6>[ 8.633057] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.719950] udevd[115]: starting version 3.2.9 <5>[ 8.726436] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.734525] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.742558] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.754657] udevd[115]: specified user 'tss' unknown <27>[ 8.760653] udevd[115]: specified group 'tss' unknown <30>[ 8.767533] udevd[116]: starting eudev-3.2.9 <6>[ 8.931618] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 8.954739] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 8.962488] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 8.969025] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 8.972352] usbcore: registered new device driver onboard-usb-hub <6>[ 9.054277] rockchip-vop ff930000.vop: Adding to iommu group 0 <6>[ 9.061509] rockchip-vop ff940000.vop: Adding to iommu group 1 <6>[ 9.069477] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 9.074836] rockchip-drm display-subsystem: bound ff930000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 9.088944] rockchip-drm display-subsystem: bound ff940000.vop (ops vop_component_ops [rockchipdrm]) <4>[ 9.092568] rtc-hym8563 0-0051: no valid clock/calendar values available <4>[ 9.099562] dwhdmi-rockchip ff980000.hdmi: supply avdd-0v9 not found, using dummy regulator <6>[ 9.107784] rtc-hym8563 0-0051: registered as rtc0 <4>[ 9.117026] dwhdmi-rockchip ff980000.hdmi: supply avdd-1v8 not found, using dummy regulator <6>[ 9.132346] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.00a with HDCP (DWC MHL PHY) <4>[ 9.133890] rtc-hym8563 0-0051: no valid clock/calendar values available <6>[ 9.145348] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <3>[ 9.150753] rtc-hym8563 0-0051: hctosys: unable to read the hardware clock <6>[ 9.156219] rockchip-drm display-subsystem: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm]) <6>[ 9.158453] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 9.158470] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 59,32 bit host data width,256 deep fifo <6>[ 9.195178] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0 <6>[ 9.196718] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq <6>[ 9.204372] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 9.211056] mmc_host mmc2: card is non-removable. <6>[ 9.220354] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 9.233585] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 9.249267] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 9.283707] panfrost ffa30000.gpu: clock rate = 400000000 <6>[ 9.301367] usb 3-1: reset high-speed USB device number 2 using ehci-platform <6>[ 9.302216] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority <6>[ 9.320204] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 <6>[ 9.329194] panfrost ffa30000.gpu: features: 00000000,00000407, issues: 00000000,24040400 <6>[ 9.338639] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <6>[ 9.351359] rk3288-crypto ff8a0000.crypto: Crypto Accelerator successfully registered <6>[ 9.352161] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 <6>[ 9.362140] [drm] Initialized panfrost 1.2.0 20180908 for ffa30000.gpu on minor 1 <6>[ 9.428474] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) <6>[ 9.442415] mmc2: new high speed SDIO card at address 0001 <5>[ 9.530759] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 9.573687] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 9.582180] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 9.591608] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 9.601542] cfg80211: failed to load regulatory.db <6>[ 9.609429] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 9.619379] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.radxa,rock2-square.bin failed with error -2 <4>[ 9.632416] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <6>[ 9.971462] onboard-usb-hub 3-1: reset high-speed USB device number 2 using ehci-platform <6>[ 10.183761] hub 3-1:1.0: USB hub found <6>[ 10.188765] hub 3-1:1.0: 4 ports detected <6>[ 10.207373] hub 3-1:1.0: USB hub found <6>[ 10.212168] hub 3-1:1.0: 4 ports detected done Saving random seed: <5>[ 10.236601] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <3>[ 10.651593] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <5>[ 22.421317] random: crng init done <5>[ 22.425409] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12682891/environment . /lava-12682891/environment / # /lava-12682891/bin/lava-test-runner /lava-12682891/0 /lava-12682891/bin/lava-test-runner /lava-12682891/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12682891/0/tests/0_dmesg<8>[ 23.001685] + cat uuid + UUID=12682891_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 23.034520] <8>[ 23.059455] <8>[ 23.083254] + set +x <8>[ 23.093503] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12682891/environment / # . /lava-12682891/environment/lava-12682891/bin/lava-test-runner /lava-12682891/1 / # /lava-12682891/bin/lava-test-runner /lava-12682891/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12682891/1/tests/1_bootrr + cat uuid + UUID=12682891_<8>[ 23.582543] 1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12682891/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-12682891/1/../bin/lava-test-case <8>[ 23.615231] /lava-12682891/1/../bin/lava-test-case <8>[ 23.641224] /lava-12682891/1/../bin/lava-test-case <8>[ 23.659862] /lava-12682891/1/../bin/lava-test-case <8>[ 23.689534] /lava-12682891/1/../bin/lava-test-case <8>[ 23.713100] /lava-12682891/1/../bin/lava-test-case <8>[ 23.734790] /lava-12682891/1/../bin/lava-test-case <8>[ 23.758118] /lava-12682891/1/../bin/lava-test-case <8>[ 23.778991] /lava-12682891/1/../bin/lava-test-case <8>[ 23.801530] + set +x <8>[ 23.810667] / #