Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.91 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 426157/tftp-deploy-64mbvmum/kernel/Image tftp 0x82000000 426157/tftp-deploy-64mbvmum/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '426157/tftp-deploy-64mbvmum/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################## 7.1 MiB/s done Bytes transferred = 57684480 (3703200 hex) => tftp 0x90080000 426157/tftp-deploy-64mbvmum/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 426157/tftp-deploy-64mbvmum/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '426157/tftp-deploy-64mbvmum/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### 15 MiB/s done Bytes transferred = 28901123 (1b8ff03 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 426157/tftp-deploy-64mbvmum/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 426157/tftp-deploy-64mbvmum/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.91; sending through gateway 172.16.0.254 Filename '426157/tftp-deploy-64mbvmum/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 9.1 MiB/s done Bytes transferred = 28772 (7064 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-02-05 13:29:55 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 28901059 Bytes = 27.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a063 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.75-cip14 (KernelCI@build-j98649-arm64-gcc-10-defconfig-kselftest-s8lmj) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Mon Feb 5 13:08:49 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f5640-0x20ff7f7fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 31 pages/cpu s89696 r8192 d29088 u126976 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3849372K/4126720K available (23168K kernel code, 7052K rwdata, 11768K rodata, 14208K init, 11400K bss, 244580K reserved, 32768K cma-reserved) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 66261 entries in 259 pages <6>[ 0.000000] ftrace: allocated 259 pages with 3 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080380000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080310000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080320000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.009127] Console: colour dummy device 80x25 <4>[ 0.013911] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.022012] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026427] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030928] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035605] ... CLASSHASH_SIZE: 4096 <4>[ 0.040282] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.045046] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049810] ... CHAINHASH_SIZE: 32768 <4>[ 0.054574] memory used by lock dependency info: 6365 kB <4>[ 0.060303] memory used for stack traces: 4224 kB <4>[ 0.065419] per task-struct memory footprint: 1920 bytes <6>[ 0.071280] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.082025] pid_max: default: 32768 minimum: 301 <6>[ 0.087308] LSM: Security Framework initializing <6>[ 0.092328] landlock: Up and running. <6>[ 0.096351] LSM support for eBPF active <6>[ 0.100803] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.108562] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.122953] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.130570] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.137269] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.144881] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.151570] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.159180] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.165864] Running RCU-tasks wait API self tests <6>[ 0.276103] rcu: Hierarchical SRCU implementation. <6>[ 0.281246] rcu: Max phase no-delay instances is 1000. <6>[ 0.286874] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.300583] Platform MSI: gic-its@6020000 domain created <6>[ 0.306415] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.314440] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.320793] EFI services will not be available. <6>[ 0.326277] smp: Bringing up secondary CPUs ... <6>[ 0.332931] Detected PIPT I-cache on CPU1 <6>[ 0.333005] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.333017] GICv3: CPU1: using allocated LPI pending table @0x0000002080330000 <6>[ 0.333062] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.333448] smp: Brought up 1 node, 2 CPUs <6>[ 0.363902] SMP: Total of 2 processors activated. <6>[ 0.368941] CPU features: detected: 32-bit EL0 Support <6>[ 0.374462] CPU features: detected: 32-bit EL1 Support <6>[ 0.379957] CPU features: detected: CRC32 instructions <6>[ 0.385529] CPU: All CPU(s) started at EL2 <6>[ 0.389963] alternatives: applying system-wide alternatives <6>[ 0.399059] devtmpfs: initialized <6>[ 0.423442] Callback from call_rcu_tasks_rude() invoked. <6>[ 0.450891] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.461050] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.475453] pinctrl core: initialized pinctrl subsystem <6>[ 0.485132] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.492800] SoC family: QorIQ LS1028A <6>[ 0.496761] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.504887] DMI not present or invalid. <6>[ 0.511056] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.520936] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.528626] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.537320] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.545836] audit: initializing netlink subsys (disabled) <5>[ 0.552056] audit: type=2000 audit(0.396:1): state=initialized audit_enabled=0 res=1 <6>[ 0.556885] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.560193] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.566837] cpuidle: using governor menu <6>[ 0.578874] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.586121] Callback from call_rcu_tasks() invoked. <6>[ 0.586161] ASID allocator initialised with 65536 entries <6>[ 0.604830] Serial: AMBA PL011 UART driver <4>[ 0.677033] KASLR disabled due to lack of seed <6>[ 0.741475] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.748724] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.755355] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.762600] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.769210] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.776342] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.782947] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.790078] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.804537] ACPI: Interpreter disabled. <6>[ 0.817821] iommu: Default domain type: Translated <6>[ 0.823045] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.831622] SCSI subsystem initialized <6>[ 0.837669] usbcore: registered new interface driver usbfs <6>[ 0.843768] usbcore: registered new interface driver hub <6>[ 0.849568] usbcore: registered new device driver usb <6>[ 0.857191] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.866882] i2c i2c-0: IMX I2C adapter registered <6>[ 0.873546] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.882490] i2c i2c-1: IMX I2C adapter registered <6>[ 0.888291] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.897389] i2c i2c-2: IMX I2C adapter registered <6>[ 0.904890] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.910242] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.919831] PTP clock support registered <6>[ 0.924603] EDAC MC: Ver: 3.0.0 <6>[ 0.934276] FPGA manager framework <6>[ 0.938719] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.947921] NET: Registered PF_ATMPVC protocol family <6>[ 0.953323] NET: Registered PF_ATMSVC protocol family <6>[ 0.959832] vgaarb: loaded <6>[ 0.964029] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.973131] VFS: Disk quotas dquot_6.6.0 <6>[ 0.977537] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.986017] pnp: PnP ACPI: disabled <6>[ 1.019555] NET: Registered PF_INET protocol family <6>[ 1.025432] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.037428] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 147456 bytes, linear) <6>[ 1.046896] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.055096] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.063624] TCP bind hash table entries: 32768 (order: 10, 4718592 bytes, vmalloc hugepage) <6>[ 1.081490] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.089359] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.098105] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.106015] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.114709] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.122583] RPC: Registered named UNIX socket transport module. <6>[ 1.128966] RPC: Registered udp transport module. <6>[ 1.134001] RPC: Registered tcp transport module. <6>[ 1.139033] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.145866] NET: Registered PF_XDP protocol family <6>[ 1.151003] PCI: CLS 0 bytes, default 64 <6>[ 1.156458] Unpacking initramfs... <6>[ 1.161426] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.180838] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.201673] kvm [1]: GICv3: no GICV resource entry <6>[ 1.216030] kvm [1]: disabling GICv2 emulation <6>[ 1.220833] kvm [1]: GIC system register CPU interface enabled <6>[ 1.244085] kvm [1]: vgic interrupt IRQ9 <6>[ 1.248496] kvm [1]: Hyp mode initialized successfully <5>[ 1.273892] Initialise system trusted keyrings <6>[ 1.284735] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.418486] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.430010] NFS: Registering the id_resolver key type <5>[ 1.435555] Key type id_resolver registered <5>[ 1.440107] Key type id_legacy registered <6>[ 1.445092] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.452217] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.461628] 9p: Installing v9fs 9p2000 file system support <6>[ 1.499008] NET: Registered PF_ALG protocol family <5>[ 1.504261] Key type asymmetric registered <5>[ 1.508718] Asymmetric key parser 'x509' registered <6>[ 1.514218] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.522041] io scheduler mq-deadline registered <6>[ 1.526909] io scheduler kyber registered <4>[ 1.532589] test_firmware: interface ready <6>[ 1.629886] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.648255] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 1.668187] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 1.688170] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 1.704154] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 1.724153] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 1.744153] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 1.760132] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 1.780343] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.800910] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.816220] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.821816] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 1.844517] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.860137] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 1.872141] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.888175] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 1.908131] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.924074] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.940249] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.956306] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.976085] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.000070] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.020061] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.040192] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 2.046159] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.076341] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.097345] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 2.112272] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.136092] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.156090] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.180222] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.208175] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 2.214092] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.240061] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.258769] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 2.265336] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.276190] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.287795] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 2.294721] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 2.301256] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.312103] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.323472] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 2.330348] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 2.336849] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.347697] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.359080] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 2.366257] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 2.372762] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.383610] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.394894] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.405838] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 2.413023] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 2.419550] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.430413] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.441780] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 2.449582] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 2.456270] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 2.465435] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 2.474645] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 2.482117] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 2.491780] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 2.499592] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 2.508665] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 2.517691] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 2.523969] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.190072] Freeing initrd memory: 28216K <3>[ 3.504238] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 3.511204] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.518275] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.524111] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.530647] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.541668] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.548256] pci 0001:00:00.0: supports D1 D2 <6>[ 3.552853] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.561477] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.568476] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.574526] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.582306] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.591261] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.600262] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 3.606526] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 4.615144] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 4.622058] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 4.629126] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 4.634961] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 4.644304] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 4.655286] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 4.661856] pci 0002:00:00.0: supports D1 D2 <6>[ 4.666453] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 4.674989] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 4.681986] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 4.691962] EINJ: ACPI disabled. <6>[ 4.781081] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 4.800254] printk: console [ttyS0] disabled <6>[ 4.805282] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.814667] printk: console [ttyS0] enabled <6>[ 4.814667] printk: console [ttyS0] enabled <6>[ 4.823681] printk: bootconsole [ns16550a0] disabled <6>[ 4.823681] printk: bootconsole [ns16550a0] disabled <6>[ 4.837399] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.848758] SuperH (H)SCI(F) driver initialized <6>[ 4.855289] msm_serial: driver initialized <6>[ 4.862136] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 4.891762] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.898539] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.903459] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.909074] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.914689] arm-smmu 5000000.iommu: nested translation <5>[ 4.920229] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.927699] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.934570] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.941322] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.948071] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.957430] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 4.993413] loop: module loaded <6>[ 4.999354] lkdtm: No crash points registered, enable through debugfs <4>[ 5.038291] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 5.051728] megasas: 07.719.03.00-rc1 <6>[ 5.070681] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 5.115409] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 5.145599] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 5.152765] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 5.158472] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 5.169976] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 5.182335] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 5.194657] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 5.206079] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 5.246131] thunder_xcv, ver 1.0 <6>[ 5.249920] thunder_bgx, ver 1.0 <6>[ 5.253674] nicpf, ver 1.0 <6>[ 5.260539] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 5.268281] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 5.380069] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 5.390693] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 5.397730] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 5.512085] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 5.520088] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 5.527076] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 5.640083] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 5.648086] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 5.656348] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 5.768090] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 5.807497] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 5.814384] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 5.822380] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 5.832216] pps pps0: new PPS source ptp0 <6>[ 5.839356] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 5.846947] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 5.852932] hclge is initializing <6>[ 5.856677] e1000: Intel(R) PRO/1000 Network Driver <6>[ 5.861855] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 5.868206] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 5.873485] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.879966] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 5.885666] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.891725] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 5.898310] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 5.905975] sky2: driver version 1.30 <6>[ 5.914379] VFIO - User Level meta-driver version: 0.3 <6>[ 5.922436] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 5.932933] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 5.952881] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.958978] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 5.967891] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 5.977774] xhci-hcd xhci-hcd.0.auto: irq 100, io mem 0x03110000 <6>[ 5.985110] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.990938] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 5.998998] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 6.009730] hub 1-0:1.0: USB hub found <6>[ 6.014067] hub 1-0:1.0: 1 port detected <6>[ 6.020549] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 6.031621] hub 2-0:1.0: USB hub found <6>[ 6.035796] hub 2-0:1.0: 1 port detected <6>[ 6.042197] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 6.048067] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 6.056803] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 6.066561] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03100000 <6>[ 6.073730] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 6.079559] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 6.087574] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 6.096939] hub 3-0:1.0: USB hub found <6>[ 6.101110] hub 3-0:1.0: 1 port detected <6>[ 6.106886] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 6.117639] hub 4-0:1.0: USB hub found <6>[ 6.121809] hub 4-0:1.0: 1 port detected <6>[ 6.129299] usbcore: registered new interface driver usb-storage <6>[ 6.147883] i2c_dev: i2c /dev entries driver <6>[ 6.173625] sp805-wdt c000000.watchdog: registration successful <6>[ 6.181021] sp805-wdt c010000.watchdog: registration successful <6>[ 6.197179] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 6.210058] sdhci: Secure Digital Host Controller Interface driver <6>[ 6.216576] sdhci: Copyright(c) Pierre Ossman <6>[ 6.223883] Synopsys Designware Multimedia Card Interface Driver <6>[ 6.234074] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.243235] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 6.249462] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.250425] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 6.272901] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 6.273361] usbcore: registered new interface driver usbhid <6>[ 6.285665] usbhid: USB HID core driver <6>[ 6.292202] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 6.299794] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 6.315434] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.323230] IPv4 over IPsec tunneling driver <6>[ 6.333544] NET: Registered PF_INET6 protocol family <6>[ 6.344921] Segment Routing with IPv6 <6>[ 6.349277] In-situ OAM (IOAM) with IPv6 <6>[ 6.355811] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.366185] NET: Registered PF_PACKET protocol family <6>[ 6.372813] 9pnet: Installing 9P2000 support <5>[ 6.377723] Key type dns_resolver registered <6>[ 6.382317] mpls_gso: MPLS GSO support <6>[ 6.393025] registered taskstats version 1 <5>[ 6.397569] Loading compiled-in X.509 certificates <6>[ 6.398428] mmc0: new HS400 MMC card at address 0001 <6>[ 6.412549] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 6.427705] mmcblk0: p1 p2 <6>[ 6.434535] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 6.451884] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <5>[ 6.459734] Loaded X.509 cert 'Build time autogenerated kernel key: 4387103beee1596650b3b04cd7170ed739af763f' <6>[ 6.465314] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (511:0) <6>[ 6.470950] ima: No TPM chip found, activating TPM-bypass! <6>[ 6.482651] ima: Allocated hash algorithm: sha1 <6>[ 6.487002] hub 1-1:1.0: USB hub found <6>[ 6.487748] ima: No architecture policies found <6>[ 6.491865] hub 1-1:1.0: 7 ports detected <6>[ 6.539559] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 6.558974] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 6.566589] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 6.574016] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 6.581493] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 6.588790] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 6.596120] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 6.708308] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 6.719418] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using ba:98:30:c2:a0:98 <6>[ 6.728296] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 6a:b7:e3:38:c5:56 <6>[ 6.752696] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 6.827679] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 6.921953] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 9.994820] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 10.003388] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.036263] Sending DHCP requests ., OK <6>[ 10.057070] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.91 <6>[ 10.065270] IP-Config: Complete: <6>[ 10.068912] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.91, mask=255.255.255.0, gw=172.16.0.254 <6>[ 10.079454] host=172.16.0.91, domain=lava.lan, nis-domain=(none) <6>[ 10.086315] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.086355] nameserver0=8.8.8.8 <6>[ 10.107652] ALSA device list: <6>[ 10.111419] No soundcards found. <6>[ 10.173579] Freeing unused kernel memory: 14208K <6>[ 10.178880] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.534879] udevd[145]: starting version 3.2.9 <5>[ 11.552310] random: crng init done <27>[ 11.565838] udevd[145]: specified user 'tss' unknown <27>[ 11.571376] udevd[145]: specified group 'tss' unknown <30>[ 11.582949] udevd[146]: starting eudev-3.2.9 <6>[ 13.387829] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 13.459686] fsl_ddr_edac acquired irq 111 for MC <27>[ 13.483450] udevd[148]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 13.494512] fsl_ddr_edac MC err registered <28>[ 13.510107] udevd[148]: could not rename interface '8' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 13.707566] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 13.771734] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 13.851089] CAN device driver interface <6>[ 13.865315] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 13.865916] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 13.878210] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 13.914146] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 13.943214] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 13.968092] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 13.992407] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <4>[ 13.996783] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 14.008731] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 14.016129] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 14.032405] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 14.040096] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <6>[ 14.058215] wm8904 2-001a: revision A <4>[ 14.062979] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 14.090285] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 14.112316] rtc-rv8803 0-0032: registered as rtc0 <6>[ 14.115063] mscc_felix 0000:00:00.5: Adding to iommu group 13 <6>[ 14.129211] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 14.141654] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 14.176812] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 14.192723] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 14.357980] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 14.653379] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 14.772287] caam 8000000.crypto: Entropy delay = 3200 <6>[ 14.807368] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 14.876132] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 14.900149] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 14.922415] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 15.150950] mali-dp f080000.display: Adding to iommu group 14 <6>[ 15.163559] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.170559] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 15.185414] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 15.588788] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 15.599042] caam algorithms registered in /proc/crypto <6>[ 15.609225] caam 8000000.crypto: registering rng-caam <6>[ 15.616911] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 15.626403] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 15.634526] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 15.642948] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-426157/environment . /lava-426157/environment / # /lava-426157/bin/lava-test-runner /lava-426157/0 /lava-426157/bin/lava-test-runner /lava-426157/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-426157/0/tests/0_dmesg + cat uuid + UUID=426157_1.5.<8>[ 16.705136] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.800407] <8>[ 16.898698] <8>[ 16.996408] + set +x <8>[ 17.016176] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-426157/environment / # . /lava-426157/environment/lava-426157/bin/lava-test-runner /lava-426157/1 / # /lava-426157/bin/lava-test-runner /lava-426157/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-426157/1/tests/1_bootrr + cat uuid + UUID=426157_1.5.<8>[ 17.617963] 2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-426157/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-426157/1/../bin/lava-test-case <8>[ 17.741514] /lava-426157/1/../bin/lava-test-case <8>[ 17.834287] /lava-426157/1/../bin/lava-test-case <8>[ 17.890672] /lava-426157/1/../bin/lava-test-case <8>[ 18.010925] /lava-426157/1/../bin/lava-test-case <8>[ 18.096800] /lava-426157/1/../bin/lava-test-case <8>[ 18.166911] /lava-426157/1/../bin/lava-test-case <8>[ 18.253813] /lava-426157/1/../bin/lava-test-case <8>[ 18.328690] /lava-426157/1/../bin/lava-test-case <8>[ 18.419291] /lava-426157/1/../bin/lava-test-case <8>[ 18.488360] /lava-426157/1/../bin/lava-test-case <8>[ 18.575358] /lava-426157/1/../bin/lava-test-case <8>[ 18.644404] /lava-426157/1/../bin/lava-test-case <8>[ 18.750059] /lava-426157/1/../bin/lava-test-case <8>[ 18.818218] /lava-426157/1/../bin/lava-test-case <8>[ 18.904669] /lava-426157/1/../bin/lava-test-case <8>[ 18.973113] /lava-426157/1/../bin/lava-test-case <8>[ 19.062003] /lava-426157/1/../bin/lava-test-case <8>[ 19.152522] /lava-426157/1/../bin/lava-test-case <8>[ 19.222397] /lava-426157/1/../bin/lava-test-case <8>[ 19.310284] /lava-426157/1/../bin/lava-test-case <8>[ 19.409344] /lava-426157/1/../bin/lava-test-case <8>[ 19.494817] /lava-426157/1/../bin/lava-test-case <8>[ 19.564528] /lava-426157/1/../bin/lava-test-case <8>[ 19.651092] /lava-426157/1/../bin/lava-test-case <8>[ 19.750327] /lava-426157/1/../bin/lava-test-case <8>[ 19.837273] /lava-426157/1/../bin/lava-test-case <8>[ 19.906508] /lava-426157/1/../bin/lava-test-case <8>[ 19.993071] /lava-426157/1/../bin/lava-test-case <8>[ 20.062270] /lava-426157/1/../bin/lava-test-case <8>[ 20.150334] /lava-426157/1/../bin/lava-test-case <8>[ 20.239709] /lava-426157/1/../bin/lava-test-case <8>[ 20.328407] /lava-426157/1/../bin/lava-test-case <8>[ 20.397764] /lava-426157/1/../bin/lava-test-case <8>[ 20.486391] /lava-426157/1/../bin/lava-test-case <8>[ 20.561568] /lava-426157/1/../bin/lava-test-case <8>[ 20.654528] /lava-426157/1/../bin/lava-test-case <8>[ 20.723079] /lava-426157/1/../bin/lava-test-case <8>[ 20.810666] /lava-426157/1/../bin/lava-test-case <8>[ 20.897584] /lava-426157/1/../bin/lava-test-case <8>[ 20.973419] /lava-426157/1/../bin/lava-test-case <8>[ 21.061553] /lava-426157/1/../bin/lava-test-case <8>[ 21.153019] /lava-426157/1/../bin/lava-test-case <8>[ 21.222476] /lava-426157/1/../bin/lava-test-case <8>[ 21.310287] /lava-426157/1/../bin/lava-test-case <8>[ 21.379846] /lava-426157/1/../bin/lava-test-case <8>[ 21.468278] /lava-426157/1/../bin/lava-test-case <8>[ 21.536264] /lava-426157/1/../bin/lava-test-case <8>[ 21.624795] /lava-426157/1/../bin/lava-test-case <8>[ 21.713036] /lava-426157/1/../bin/lava-test-case <8>[ 21.782428] /lava-426157/1/../bin/lava-test-case <8>[ 21.869258] /lava-426157/1/../bin/lava-test-case <8>[ 21.959121] /lava-426157/1/../bin/lava-test-case <8>[ 22.027934] /lava-426157/1/../bin/lava-test-case <8>[ 22.116188] /lava-426157/1/../bin/lava-test-case <8>[ 22.205906] /lava-426157/1/../bin/lava-test-case <8>[ 22.275450] /lava-426157/1/../bin/lava-test-case <8>[ 22.363142] /lava-426157/1/../bin/lava-test-case <8>[ 22.432515] /lava-426157/1/../bin/lava-test-case <8>[ 22.521291] /lava-426157/1/../bin/lava-test-case <8>[ 22.589847] /lava-426157/1/../bin/lava-test-case <8>[ 22.682579] /lava-426157/1/../bin/lava-test-case <8>[ 22.770710] /lava-426157/1/../bin/lava-test-case <8>[ 22.858332] /lava-426157/1/../bin/lava-test-case <8>[ 22.946589] /lava-426157/1/../bin/lava-test-case <8>[ 23.015990] /lava-426157/1/../bin/lava-test-case <8>[ 23.103478] /lava-426157/1/../bin/lava-test-case <8>[ 23.192728] /lava-426157/1/../bin/lava-test-case <8>[ 23.262177] /lava-426157/1/../bin/lava-test-case <8>[ 23.350342] /lava-426157/1/../bin/lava-test-case <8>[ 23.419617] /lava-426157/1/../bin/lava-test-case <8>[ 23.509359] /lava-426157/1/../bin/lava-test-case <8>[ 23.582389] /lava-426157/1/../bin/lava-test-case <8>[ 23.669704] /lava-426157/1/../bin/lava-test-case <8>[ 23.738177] /lava-426157/1/../bin/lava-test-case <8>[ 23.825830] /lava-426157/1/../bin/lava-test-case <8>[ 23.899077] /lava-426157/1/../bin/lava-test-case <8>[ 23.986805] /lava-426157/1/../bin/lava-test-case <8>[ 24.055783] /lava-426157/1/../bin/lava-test-case <8>[ 24.144469] /lava-426157/1/../bin/lava-test-case <8>[ 24.214374] /lava-426157/1/../bin/lava-test-case <8>[ 24.302939] /lava-426157/1/../bin/lava-test-case <8>[ 24.371570] /lava-426157/1/../bin/lava-test-case <8>[ 24.462980] /lava-426157/1/../bin/lava-test-case <8>[ 24.550818] /lava-426157/1/../bin/lava-test-case <8>[ 24.620284] /lava-426157/1/../bin/lava-test-case <8>[ 24.709090] /lava-426157/1/../bin/lava-test-case <8>[ 24.797440] /lava-426157/1/../bin/lava-test-case <8>[ 24.886483] /lava-426157/1/../bin/lava-test-case <8>[ 24.974236] /lava-426157/1/../bin/lava-test-case <8>[ 25.044564] /lava-426157/1/../bin/lava-test-case <8>[ 25.134182] /lava-426157/1/../bin/lava-test-case <8>[ 25.208263] /lava-426157/1/../bin/lava-test-case <8>[ 25.294853] /lava-426157/1/../bin/lava-test-case <8>[ 25.362880] /lava-426157/1/../bin/lava-test-case <8>[ 25.448374] /lava-426157/1/../bin/lava-test-case <8>[ 25.538779] /lava-426157/1/../bin/lava-test-case <8>[ 25.607971] /lava-426157/1/../bin/lava-test-case <8>[ 25.694207] /lava-426157/1/../bin/lava-test-case <8>[ 25.763705] /lava-426157/1/../bin/lava-test-case <8>[ 25.852726] + set +x <8>[ 25.888812] / # �