Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot 2019.04-linux4sam_6.2-icp (May 18 2022 - 22:17:10 +0000), Build: HEAD-0.00-20220518221710 CPU: SAMA7 Reset Source : SYSRESET Watchdog enabled DRAM: 1 GiB MMC: emmc@e0830000: 0 Loading Environment from SPI Flash... SF: Detected sst26vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial VPD: BOARD_SERIAL K1FT90005, MAC 00:A0:A5:5C:6D:A2 Net: eth0: port0 [PRIME], eth1: port1, eth2: port2, eth3: port3, eth4: port4, eth5: port5, eth6: port6, eth7: port7 POST memory PASSED POST env PASSED POST vpd PASSED => setenv autoload no setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp dhcp port4 Waiting for PHY auto negotiation to complete...... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.126 (761 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x62000000 453533/tftp-deploy-3_yick6u/kernel/zImage tftp 0x62000000 453533/tftp-deploy-3_yick6u/kernel/zImage tftp 0x62000000 453533/tftp-deploy-3_yick6u/kernel/zImage port4 Waiting for PHY auto negotiation to complete..... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '453533/tftp-deploy-3_yick6u/kernel/zImage'. Load address: 0x62000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ### 1.6 MiB/s done Bytes transferred = 10527232 (a0a200 hex) => tftp 0x68080000 453533/tftp-deploy-3_yick6u/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 453533/tftp-deploy-3_yick6u/ramdisk/ramdisk.cpio.gz.uboot tftp 0x68080000 453533/tftp-deploy-3_yick6u/ramdisk/ramdisk.cpio.gz.uboot port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '453533/tftp-deploy-3_yick6u/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 2.1 MiB/s done Bytes transferred = 17153732 (105bec4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 453533/tftp-deploy-3_yick6u/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb tftp 0x68000000 453533/tftp-deploy-3_yick6u/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb tftp 0x68000000 453533/tftp-deploy-3_yick6u/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb port4 Waiting for PHY auto negotiation to complete....... done Using port4 device TFTP from server 10.228.65.1; our IP address is 172.16.0.126; sending through gateway 172.16.0.254 Filename '453533/tftp-deploy-3_yick6u/dtb/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb'. Load address: 0x68000000 Loading: *# 2 KiB/s done Bytes transferred = 13800 (35e8 hex) => setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 bootz 0x62000000 0x68080000 0x68000000 ## Loading init Ramdisk from Legacy Image at 68080000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 17153668 Bytes = 16.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Using Device Tree in place at 68000000, end 680065e7 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.1.86-cip19 (KernelCI@build-j170710-arm-gcc-10-multi-v7-defconfig-knqjc) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Apr 18 18:52:29 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Kontron KSwitch D10 MMT 6G-2GS [ 0.000000] earlycon: atmel_serial0 at MMIO 0xe0040200 (options '115200n8') [ 0.000000] printk: bootconsole [atmel_serial0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000060000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000060000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s34580 r8192 d22764 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 930704K/1048576K available (14336K kernel code, 2470K rwdata, 6212K rodata, 2048K init, 427K bss, 52336K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 37.50MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x8a60dd6a9, max_idle_ns: 440795204056 ns <6>[ 0.000002] sched_clock: 56 bits at 38MHz, resolution 26ns, wraps every 2199023255540ns <6>[ 0.008281] Switching to timer-based delay loop, resolution 26ns <6>[ 0.017487] Console: colour dummy device 80x30 <6>[ 0.022159] Calibrating delay loop (skipped), value calculated using timer frequency.. 75.00 BogoMIPS (lpj=375000) <6>[ 0.032749] CPU: Testing write buffer coherency: ok <6>[ 0.037865] pid_max: default: 32768 minimum: 301 <6>[ 0.043055] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.050523] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.060104] CPU0: update cpu_capacity 1024 <6>[ 0.064355] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071779] Setting up static identity map for 0x60300000 - 0x603000ac <6>[ 0.079425] rcu: Hierarchical SRCU implementation. <6>[ 0.084419] rcu: Max phase no-delay instances is 1000. <6>[ 0.091899] EFI services will not be available. <6>[ 0.096932] smp: Bringing up secondary CPUs ... <6>[ 0.101597] smp: Brought up 1 node, 1 CPU <6>[ 0.105869] SMP: Total of 1 processors activated (75.00 BogoMIPS). <6>[ 0.112361] CPU: All CPU(s) started in SVC mode. <6>[ 0.118138] devtmpfs: initialized <6>[ 0.127153] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.135409] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.145453] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.156547] pinctrl core: initialized pinctrl subsystem <6>[ 0.165015] DMI not present or invalid. <6>[ 0.170598] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.179673] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.190035] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.190206] cpuidle: using governor menu <6>[ 0.201046] No ATAGs? <6>[ 0.203523] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.211764] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.220857] Serial: AMBA PL011 UART driver <6>[ 0.281270] at_xdmac e0068000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.292454] iommu: Default domain type: Translated <6>[ 0.297474] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.305184] SCSI subsystem initialized <6>[ 0.335142] usbcore: registered new interface driver usbfs <6>[ 0.340848] usbcore: registered new interface driver hub <6>[ 0.346474] usbcore: registered new device driver usb <6>[ 0.353223] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.358376] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.367770] PTP clock support registered <6>[ 0.372180] EDAC MC: Ver: 3.0.0 <6>[ 0.429159] vgaarb: loaded <6>[ 0.432824] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.468524] NET: Registered PF_INET protocol family <6>[ 0.474067] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.485263] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) <6>[ 0.493867] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.501824] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 0.509966] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) <6>[ 0.517720] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.524451] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.531287] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 0.538942] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.637712] RPC: Registered named UNIX socket transport module. <6>[ 0.643836] RPC: Registered udp transport module. <6>[ 0.648758] RPC: Registered tcp transport module. <6>[ 0.653749] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.660454] PCI: CLS 0 bytes, default 64 <5>[ 0.666630] Initialise system trusted keyrings <6>[ 0.672195] Trying to unpack rootfs image as initramfs... <6>[ 0.764638] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 0.781200] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.823146] NFS: Registering the id_resolver key type <5>[ 0.828458] Key type id_resolver registered <5>[ 0.832853] Key type id_legacy registered <6>[ 0.837269] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.844148] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.851843] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 0.933423] Key type asymmetric registered <5>[ 0.937674] Asymmetric key parser 'x509' registered <6>[ 0.943209] bounce: pool size: 64 pages <6>[ 0.947381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 0.954977] io scheduler mq-deadline registered <6>[ 0.959715] io scheduler kyber registered <6>[ 1.043399] pinctrl-ocelot e2004064.pinctrl: driver registered <6>[ 1.386525] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 1.407637] SuperH (H)SCI(F) driver initialized <6>[ 1.413543] msm_serial: driver initialized <6>[ 1.417770] STMicroelectronics ASC driver initialized <6>[ 1.424254] STM32 USART driver initialized <6>[ 1.574646] brd: module loaded <6>[ 1.605446] loop: module loaded <6>[ 1.615020] atmel_usart_serial atmel_usart_serial.0.auto: Using FIFO (32 data) <6>[ 1.622758] atmel_usart_serial.0.auto: ttyAT0 at MMIO 0xe0040200 (irq = 32, base_baud = 12500000) is a ATMEL_SERIAL<6>[ 1.633572] printk: console [ttyAT0] enabled <6>[ 1.633572] printk: console [ttyAT0] enabled <6>[ 1.642507] printk: bootconsole [atmel_serial0] disabled <6>[ 1.642507] printk: bootconsole [atmel_serial0] disabled <6>[ 1.789303] CAN device driver interface <6>[ 1.794872] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 1.801870] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.807145] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.813424] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.819044] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.829776] pegasus: Pegasus/Pegasus II USB Ethernet driver <6>[ 1.835757] usbcore: registered new interface driver pegasus <6>[ 1.841722] usbcore: registered new interface driver asix <6>[ 1.847441] usbcore: registered new interface driver ax88179_178a <6>[ 1.853837] usbcore: registered new interface driver cdc_ether <6>[ 1.859951] usbcore: registered new interface driver smsc75xx <6>[ 1.866002] usbcore: registered new interface driver smsc95xx <6>[ 1.872012] usbcore: registered new interface driver net1080 <6>[ 1.877971] usbcore: registered new interface driver cdc_subset <6>[ 1.884209] usbcore: registered new interface driver zaurus <6>[ 1.890106] usbcore: registered new interface driver cdc_ncm <6>[ 1.901437] usbcore: registered new interface driver usb-storage <6>[ 1.914350] i2c_dev: i2c /dev entries driver <6>[ 2.312419] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.319040] sdhci: Copyright(c) Pierre Ossman <6>[ 2.326079] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.334507] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.453440] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.463237] usbcore: registered new interface driver usbhid <6>[ 2.469052] usbhid: USB HID core driver <6>[ 2.482239] NET: Registered PF_INET6 protocol family <6>[ 2.569436] Segment Routing with IPv6 <6>[ 2.573550] In-situ OAM (IOAM) with IPv6 <6>[ 2.577822] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.585146] NET: Registered PF_PACKET protocol family <6>[ 2.590436] can: controller area network core <6>[ 2.595228] NET: Registered PF_CAN protocol family <6>[ 2.600247] can: raw protocol <6>[ 2.603511] can: broadcast manager protocol <6>[ 2.607927] can: netlink gateway - max_hops=1 <5>[ 2.613433] Key type dns_resolver registered <6>[ 2.618125] ThumbEE CPU extension supported. <5>[ 2.622627] Registering SWP/SWPB emulation handler <5>[ 2.773718] Loading compiled-in X.509 certificates <6>[ 5.068616] Freeing initrd memory: 16752K <6>[ 15.348260] Freeing unused kernel image (initmem) memory: 2048K <6>[ 15.352214] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.616610] udevd[90]: starting version 3.2.9 <5>[ 18.172816] random: crng init done <27>[ 18.188850] udevd[90]: specified user 'tss' unknown <27>[ 18.191619] udevd[90]: specified group 'tss' unknown <30>[ 18.213260] udevd[91]: starting eudev-3.2.9 <6>[ 20.740370] atmel_aes e004c000.crypto: version: 0x702 <6>[ 20.788815] MAC addr was not set, use random MAC <6>[ 20.846671] atmel_sha e006c000.crypto: version: 0x700 <6>[ 20.917625] atmel_sha e006c000.crypto: using dma0chan2 for DMA transfers <6>[ 20.933116] atmel_aes e004c000.crypto: Atmel AES - Using dma0chan0, dma0chan1 for DMA transfers <6>[ 21.035007] atmel_sha e006c000.crypto: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 21.158166] MAC addr was not set, use random MAC <6>[ 21.366384] at91_i2c e0044600.i2c: using dma0chan3 (tx) and dma0chan4 (rx) for DMA transfers <6>[ 21.373895] atmel_spi e0064400.spi: Using dma0chan5 (tx) and dma0chan6 (rx) for DMA transfers <6>[ 21.381260] atmel_spi e0064400.spi: Using FIFO (32 data) <6>[ 21.473282] at91_i2c e0044600.i2c: AT91 i2c bus driver (hw version: 0x820). <6>[ 21.535174] at91_i2c e0070600.i2c: using dma0chan7 (tx) and dma0chan8 (rx) for DMA transfers <6>[ 21.541655] atmel_spi e0064400.spi: Atmel SPI Controller version 0x401 at 0xe0064400 (irq 43) <6>[ 21.609124] at91_i2c e0070600.i2c: AT91 i2c bus driver (hw version: 0x820). <6>[ 21.633199] sfp sfp0: Host maximum power 2.5W <6>[ 21.717361] sfp sfp1: Host maximum power 2.5W <6>[ 21.767601] MAC addr was not set, use random MAC <6>[ 21.955588] sfp sfp0: module AGILENT HFBR-5710L rev sn 0304140604014998 dc 030414 <6>[ 22.047281] sfp sfp1: module AGILENT HFBR-5710L rev sn 0304140555048996 dc 030414 <6>[ 22.086890] MAC addr was not set, use random MAC <6>[ 22.115657] hwmon hwmon0: temp1_input not attached to any thermal zone <6>[ 22.259651] lan966x-switch e0000000.switch (unnamed net_device) (uninitialized): switched to inband/1000base-x link mode <6>[ 22.300181] lan966x-switch e0000000.switch (unnamed net_device) (uninitialized): switched to inband/1000base-x link mode done Saving random seed: OK Starting network: OK Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # # / # export SHELL=/bin/sh export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-453533/environment . /lava-453533/environment . /lava-453533/environment / # /lava-453533/bin/lava-test-runner /lava-453533/0 /lava-453533/bin/lava-test-runner /lava-453533/0 /lava-453533/bin/lava-test-runner /lava-453533/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-453533/0/tests/0_dmesg + cat uuid + UUID=453533_1.5.2.4.1 + set +x <8>[ 25.448783] + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 25.522497] <8>[ 25.588284] <8>[ 25.654031] + set +x <8>[ 25.662251] / #