Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.67 (1260 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 467027/tftp-deploy-qso5ogcs/kernel/Image tftp 0x82000000 467027/tftp-deploy-qso5ogcs/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.67; sending through gateway 172.16.0.254 Filename '467027/tftp-deploy-qso5ogcs/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## 5.6 MiB/s done Bytes transferred = 58098176 (3768200 hex) => tftp 0x90080000 467027/tftp-deploy-qso5ogcs/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 467027/tftp-deploy-qso5ogcs/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.67; sending through gateway 172.16.0.254 Filename '467027/tftp-deploy-qso5ogcs/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 8.8 MiB/s done Bytes transferred = 28821014 (1b7c616 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 467027/tftp-deploy-qso5ogcs/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 467027/tftp-deploy-qso5ogcs/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.67; sending through gateway 172.16.0.254 Filename '467027/tftp-deploy-qso5ogcs/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *## 4.5 MiB/s done Bytes transferred = 28448 (6f20 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-06-04 14:48:52 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 28820950 Bytes = 27.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 0000000090009f1f WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.91-cip21 (KernelCI@build-j216545-arm64-gcc-10-defconfig-kselftest-swxpm) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Jun 4 14:28:39 UTC 2024 [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7d4640-0x20ff7d6fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 [ 0.000000] percpu: Embedded 32 pages/cpu s92768 r8192 d30112 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3916528K/4194304K available (23424K kernel code, 7072K rwdata, 11824K rodata, 14272K init, 11399K bss, 245008K reserved, 32768K cma-reserved) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 66984 entries in 262 pages <6>[ 0.000000] ftrace: allocated 262 pages with 3 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080380000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080310000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080320000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.009156] Console: colour dummy device 80x25 <4>[ 0.013945] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.022047] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026462] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030965] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035642] ... CLASSHASH_SIZE: 4096 <4>[ 0.040320] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.045085] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049850] ... CHAINHASH_SIZE: 32768 <4>[ 0.054614] memory used by lock dependency info: 6365 kB <4>[ 0.060344] memory used for stack traces: 4224 kB <4>[ 0.065460] per task-struct memory footprint: 1920 bytes <6>[ 0.071320] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.082065] pid_max: default: 32768 minimum: 301 <6>[ 0.087352] LSM: Security Framework initializing <6>[ 0.092375] landlock: Up and running. <6>[ 0.096399] LSM support for eBPF active <6>[ 0.100857] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.108617] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.123000] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.130615] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.137316] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.144929] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.151617] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.159226] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.165914] Running RCU-tasks wait API self tests <6>[ 0.276166] rcu: Hierarchical SRCU implementation. <6>[ 0.281308] rcu: Max phase no-delay instances is 1000. <6>[ 0.286937] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.300455] Platform MSI: gic-its@6020000 domain created <6>[ 0.306285] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.314309] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.320660] EFI services will not be available. <6>[ 0.326134] smp: Bringing up secondary CPUs ... <6>[ 0.332787] Detected PIPT I-cache on CPU1 <6>[ 0.332890] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.332902] GICv3: CPU1: using allocated LPI pending table @0x0000002080330000 <6>[ 0.332949] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.333337] smp: Brought up 1 node, 2 CPUs <6>[ 0.363793] SMP: Total of 2 processors activated. <6>[ 0.368831] CPU features: detected: 32-bit EL0 Support <6>[ 0.374352] CPU features: detected: 32-bit EL1 Support <6>[ 0.379848] CPU features: detected: CRC32 instructions <6>[ 0.385419] CPU: All CPU(s) started at EL2 <6>[ 0.389852] alternatives: applying system-wide alternatives <6>[ 0.400057] devtmpfs: initialized <6>[ 0.420534] Callback from call_rcu_tasks_rude() invoked. <6>[ 0.449950] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.460110] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.478939] pinctrl core: initialized pinctrl subsystem <6>[ 0.488603] Machine: Kontron KBox A-230-LS <6>[ 0.493024] SoC family: QorIQ LS1028A <6>[ 0.496985] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.505067] DMI not present or invalid. <6>[ 0.511243] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.521107] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.528875] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.537650] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.546159] audit: initializing netlink subsys (disabled) <5>[ 0.552388] audit: type=2000 audit(0.400:1): state=initialized audit_enabled=0 res=1 <6>[ 0.557185] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.560524] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.567164] cpuidle: using governor menu <6>[ 0.579168] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.586418] Callback from call_rcu_tasks() invoked. <6>[ 0.586458] ASID allocator initialised with 65536 entries <6>[ 0.605128] Serial: AMBA PL011 UART driver <4>[ 0.673593] KASLR disabled due to lack of seed <6>[ 0.737017] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.744254] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.750886] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.758109] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.764719] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.771851] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.778458] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.785590] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.799940] ACPI: Interpreter disabled. <6>[ 0.812739] iommu: Default domain type: Translated <6>[ 0.817964] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.826540] SCSI subsystem initialized <6>[ 0.832603] usbcore: registered new interface driver usbfs <6>[ 0.838693] usbcore: registered new interface driver hub <6>[ 0.844486] usbcore: registered new device driver usb <6>[ 0.852071] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.861752] i2c i2c-0: IMX I2C adapter registered <6>[ 0.868421] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.877076] i2c i2c-1: IMX I2C adapter registered <6>[ 0.882873] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.891241] i2c i2c-2: IMX I2C adapter registered <6>[ 0.898258] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.903610] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.913235] PTP clock support registered <6>[ 0.918007] EDAC MC: Ver: 3.0.0 <6>[ 0.927182] FPGA manager framework <6>[ 0.931596] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.940729] NET: Registered PF_ATMPVC protocol family <6>[ 0.946133] NET: Registered PF_ATMSVC protocol family <6>[ 0.952608] vgaarb: loaded <6>[ 0.956814] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.966291] VFS: Disk quotas dquot_6.6.0 <6>[ 0.970732] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.979223] pnp: PnP ACPI: disabled <6>[ 1.013075] NET: Registered PF_INET protocol family <6>[ 1.018603] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.030159] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 147456 bytes, linear) <6>[ 1.039634] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.047834] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.056359] TCP bind hash table entries: 32768 (order: 10, 4718592 bytes, vmalloc hugepage) <6>[ 1.074207] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.082069] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.090803] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.098703] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.107541] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.115408] RPC: Registered named UNIX socket transport module. <6>[ 1.121735] RPC: Registered udp transport module. <6>[ 1.126766] RPC: Registered tcp transport module. <6>[ 1.131795] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.138625] NET: Registered PF_XDP protocol family <6>[ 1.143759] PCI: CLS 0 bytes, default 64 <6>[ 1.149183] Unpacking initramfs... <6>[ 1.160960] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.177577] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.198448] kvm [1]: GICv3: no GICV resource entry <6>[ 1.212828] kvm [1]: disabling GICv2 emulation <6>[ 1.217635] kvm [1]: GIC system register CPU interface enabled <6>[ 1.233005] kvm [1]: vgic interrupt IRQ9 <6>[ 1.244905] kvm [1]: Hyp mode initialized successfully <5>[ 1.266363] Initialise system trusted keyrings <6>[ 1.289079] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.444229] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.472489] NFS: Registering the id_resolver key type <5>[ 1.485033] Key type id_resolver registered <5>[ 1.489578] Key type id_legacy registered <6>[ 1.501555] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.520972] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.538570] 9p: Installing v9fs 9p2000 file system support <6>[ 1.612308] NET: Registered PF_ALG protocol family <5>[ 1.621227] Key type asymmetric registered <5>[ 1.625710] Asymmetric key parser 'x509' registered <6>[ 1.641192] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.660959] io scheduler mq-deadline registered <6>[ 1.669108] io scheduler kyber registered <4>[ 1.684985] test_firmware: interface ready <6>[ 1.791787] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.805029] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 1.829012] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 1.845050] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 1.861075] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 1.885018] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 1.904944] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 1.920924] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 1.941115] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.961566] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.976861] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.982456] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 2.000860] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 2.016847] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 2.032993] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 2.048958] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 2.064934] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 2.080874] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 2.097037] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 2.113096] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.127690] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.139082] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.150265] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.161981] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 2.167935] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.178263] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.190233] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 2.196766] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.207627] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.218908] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.230013] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.241649] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 2.247527] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.257836] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.269859] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 2.276370] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.287459] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.298919] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 2.305853] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 2.312388] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.323249] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.334633] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 2.341674] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 2.348190] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.359036] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.370402] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 2.377735] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 2.384254] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.395126] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.406411] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.417340] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 2.424335] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 2.430836] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.441684] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.453064] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 2.460929] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 2.467659] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 2.476928] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 2.486134] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 2.493735] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 2.503352] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 2.511220] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 2.520278] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 2.529302] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 2.535574] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.160996] Freeing initrd memory: 28140K <3>[ 3.521023] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 3.527966] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.535037] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.540873] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.547407] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.558425] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.565018] pci 0001:00:00.0: supports D1 D2 <6>[ 3.569616] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.578231] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.585232] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.591276] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.599054] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.608009] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.616996] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 3.623260] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 4.625058] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 4.631920] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 4.638988] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 4.644823] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 4.654166] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 4.665147] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 4.671717] pci 0002:00:00.0: supports D1 D2 <6>[ 4.676313] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 4.684838] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 4.691833] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 4.701646] EINJ: ACPI disabled. <6>[ 4.784992] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 4.803803] printk: console [ttyS0] disabled <6>[ 4.808923] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.818299] printk: console [ttyS0] enabled <6>[ 4.818299] printk: console [ttyS0] enabled <6>[ 4.827333] printk: bootconsole [ns16550a0] disabled <6>[ 4.827333] printk: bootconsole [ns16550a0] disabled <6>[ 4.841062] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.852320] SuperH (H)SCI(F) driver initialized <6>[ 4.858751] msm_serial: driver initialized <6>[ 4.865451] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 4.894781] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.901554] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.906474] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.912120] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.917737] arm-smmu 5000000.iommu: nested translation <5>[ 4.923278] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.930746] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.937604] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.944355] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.951105] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.960352] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 4.995984] loop: module loaded <6>[ 5.002030] lkdtm: No crash points registered, enable through debugfs <4>[ 5.040938] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 5.054387] megasas: 07.719.03.00-rc1 <6>[ 5.063922] ahci-qoriq 3200000.sata: Adding to iommu group 0 <4>[ 5.070956] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator <4>[ 5.079619] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator <4>[ 5.087651] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator <6>[ 5.096426] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode <6>[ 5.105719] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst <6>[ 5.119067] scsi host0: ahci-qoriq <6>[ 5.124570] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 96 <6>[ 5.146606] spi-nor spi0.0: w25q32dw (4096 Kbytes) <5>[ 5.179971] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 5.187138] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 5.192732] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 5.205247] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 5.217518] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 5.230059] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 5.241425] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 5.281043] thunder_xcv, ver 1.0 <6>[ 5.284790] thunder_bgx, ver 1.0 <6>[ 5.288552] nicpf, ver 1.0 <6>[ 5.294878] fsl_enetc 0000:00:00.0: Adding to iommu group 1 <6>[ 5.302285] fsl_enetc 0000:00:00.1: Adding to iommu group 2 <6>[ 5.309703] fsl_enetc 0000:00:00.2: Adding to iommu group 3 <6>[ 5.316935] fsl_enetc 0000:00:00.6: Adding to iommu group 4 <6>[ 5.325362] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 5 <6>[ 5.436854] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 5.447506] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 5.501066] mdio_bus 0000:00:00.3:04: Fixed dependency cycle(s) with /soc/pcie@1f0000000/mdio@0,3/ethernet-phy@4/vddio-regulator <5>[ 5.541260] bcm_phy_lib: module verification failed: signature and/or required key missing - tainting kernel <6>[ 5.657544] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 6 <6>[ 5.664612] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 5.672632] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 5.682419] pps pps0: new PPS source ptp0 <6>[ 5.689471] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 5.697027] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 5.703004] hclge is initializing <6>[ 5.706721] e1000: Intel(R) PRO/1000 Network Driver <6>[ 5.711902] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 5.718221] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 5.723491] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.729974] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 5.735678] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.741747] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 5.748322] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 5.755879] sky2: driver version 1.30 <6>[ 5.764044] VFIO - User Level meta-driver version: 0.3 <6>[ 5.771982] dwc3 3100000.usb: Adding to iommu group 7 <6>[ 5.781638] dwc3 3110000.usb: Adding to iommu group 8 <6>[ 5.800828] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.806923] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 5.815820] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 5.825692] xhci-hcd xhci-hcd.0.auto: irq 101, io mem 0x03110000 <6>[ 5.833115] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.838957] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 5.846960] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.857383] hub 1-0:1.0: USB hub found <6>[ 5.861756] hub 1-0:1.0: 1 port detected <6>[ 5.868216] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.879240] hub 2-0:1.0: USB hub found <6>[ 5.883429] hub 2-0:1.0: 1 port detected <6>[ 5.890871] usbcore: registered new interface driver usb-storage <6>[ 5.908275] i2c_dev: i2c /dev entries driver <6>[ 5.932509] sp805-wdt c000000.watchdog: registration successful <6>[ 5.939892] sp805-wdt c010000.watchdog: registration successful <6>[ 5.955286] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 5.968142] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.974661] sdhci: Copyright(c) Pierre Ossman <6>[ 5.981764] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.991915] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.001742] sdhci-esdhc 2140000.mmc: Adding to iommu group 9 <6>[ 6.008937] sdhci-esdhc 2150000.mmc: Adding to iommu group 10 <6>[ 6.015279] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.031773] usbcore: registered new interface driver usbhid <6>[ 6.037672] usbhid: USB HID core driver <6>[ 6.048860] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 6.056420] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 6.066059] IPv4 over IPsec tunneling driver <6>[ 6.076247] NET: Registered PF_INET6 protocol family <6>[ 6.087899] Segment Routing with IPv6 <6>[ 6.092283] In-situ OAM (IOAM) with IPv6 <6>[ 6.098816] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.109225] NET: Registered PF_PACKET protocol family <6>[ 6.115357] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <6>[ 6.129280] 8021q: 802.1Q VLAN Support v1.8 <6>[ 6.132867] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 6.134469] 9pnet: Installing 9P2000 support <5>[ 6.145441] Key type dns_resolver registered <6>[ 6.150033] mpls_gso: MPLS GSO support <6>[ 6.157525] mmc0: new HS400 MMC card at address 0001 <6>[ 6.166886] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 6.166942] registered taskstats version 1 <5>[ 6.176378] Loading compiled-in X.509 certificates <6>[ 6.181769] mmcblk0: p1 p2 p3 <6>[ 6.189458] mmcblk0boot0: mmc0:0001 S0J58X 31.5 MiB <6>[ 6.203723] mmcblk0boot1: mmc0:0001 S0J58X 31.5 MiB <6>[ 6.217127] mmcblk0rpmb: mmc0:0001 S0J58X 4.00 MiB, chardev (511:0) <5>[ 6.237386] Loaded X.509 cert 'Build time autogenerated kernel key: cbbccf4afebd26771eb2f0b55eb6eb36ca23266c' <6>[ 6.248417] ima: No TPM chip found, activating TPM-bypass! <6>[ 6.254252] ima: Allocated hash algorithm: sha1 <6>[ 6.259245] ima: No architecture policies found <6>[ 6.308344] fsl-edma 22c0000.dma-controller: Adding to iommu group 11 <6>[ 6.328479] pcieport 0001:00:00.0: Adding to iommu group 12 <6>[ 6.335510] hub 1-1:1.0: USB hub found <6>[ 6.339835] hub 1-1:1.0: 7 ports detected <6>[ 6.345945] pcieport 0001:00:00.0: PME: Signaling with IRQ 105 <6>[ 6.354726] pcieport 0001:00:00.0: AER: enabled with IRQ 105 <6>[ 6.362541] pcieport 0002:00:00.0: Adding to iommu group 13 <6>[ 6.370762] pcieport 0002:00:00.0: PME: Signaling with IRQ 106 <6>[ 6.377777] pcieport 0002:00:00.0: AER: enabled with IRQ 106 <6>[ 6.488896] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 6.500216] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using e6:6e:b1:5d:fd:ce <6>[ 6.509085] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using aa:79:d7:c4:59:a6 <6>[ 6.633487] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 6.644679] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using 3e:5d:d7:d3:cc:2e <6>[ 6.653545] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using ee:32:0a:82:ac:7a <6>[ 6.688882] usb 1-1.6: new full-speed USB device number 3 using xhci-hcd <6>[ 6.772964] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 6.781382] fsl_enetc 0000:00:00.2: no MAC address specified for SI0, using 9e:f0:71:ac:e4:f5 <3>[ 6.859776] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <6>[ 6.901101] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 6.909580] fsl_enetc 0000:00:00.6: no MAC address specified for SI0, using 7e:e3:9c:dc:08:7e <6>[ 6.938997] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 6.955006] 8021q: adding VLAN 0 to HW filter on device bond0 <6>[ 7.028271] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 7.123497] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 7.200432] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.3:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 7.294996] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 7.353755] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 7.362224] fsl_enetc 0000:00:00.2 eth2: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 7.408699] fsl_enetc 0000:00:00.6 eth3: configuring for fixed/internal link mode <6>[ 7.416608] fsl_enetc 0000:00:00.6 eth3: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 7.424888] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready <6>[ 7.432193] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready <5>[ 7.436864] Sending DHCP requests .. <6>[ 10.215915] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 10.228318] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <4>[ 13.793006] ., OK <6>[ 13.811566] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.67 <6>[ 13.819778] IP-Config: Complete: <6>[ 13.823483] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.67, mask=255.255.255.0, gw=172.16.0.254 <6>[ 13.834032] host=172.16.0.67, domain=lava.lan, nis-domain=(none) <6>[ 13.840894] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 13.840934] nameserver0=8.8.8.8 <6>[ 13.930498] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 13.975729] fsl_enetc 0000:00:00.6 eth3: Link is Down <6>[ 14.020453] clk: Disabling unused clocks <6>[ 14.024970] ALSA device list: <6>[ 14.028274] No soundcards found. <6>[ 14.078404] Freeing unused kernel memory: 14272K <6>[ 14.083495] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.436455] udevd[148]: starting version 3.2.9 <5>[ 15.420962] random: crng init done <27>[ 15.434207] udevd[148]: specified user 'tss' unknown <27>[ 15.439742] udevd[148]: specified group 'tss' unknown <30>[ 15.451227] udevd[149]: starting eudev-3.2.9 <6>[ 17.180490] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 17.269183] fsl_ddr_edac acquired irq 121 for MC <6>[ 17.290543] fsl_ddr_edac MC err registered <6>[ 17.417953] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <6>[ 17.469652] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <27>[ 17.505576] udevd[151]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 17.555709] fsl_enetc 0000:00:00.6 enp0s0f6: renamed from eth3 <28>[ 17.569010] udevd[151]: could not rename interface '7' from 'eth0' to 'enp0s0f0': Device or resource busy <4>[ 17.605671] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 17.616838] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 17.646410] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 17.654139] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 17.675106] mscc_felix 0000:00:00.5: Adding to iommu group 14 <4>[ 17.701490] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 17.709185] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 17.733574] rtc-rv8803 0-0032: registered as rtc0 <6>[ 17.741769] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <6>[ 17.771323] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 17.778630] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 17.796851] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 17.805809] mscc_felix 0000:00:00.5: Failed to find a tagging driver for protocol ocelot-8021q, using default <4>[ 17.837402] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 17.905082] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 17.905871] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 17.945060] mscc_felix 0000:00:00.5: Failed to find a tagging driver for protocol ocelot-8021q, using default <4>[ 18.043899] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 18.145145] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <6>[ 18.160922] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <6>[ 18.175328] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 18.206908] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <6>[ 18.292971] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <6>[ 18.478988] CAN device driver interface <6>[ 18.488630] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 18.517485] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control rx/tx <6>[ 18.536419] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 18.569627] mscc_felix 0000:00:00.5: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 18.641071] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.664501] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 18.848501] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 18.855561] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 18.892164] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Broadcom BCM54140] (irq=POLL) <6>[ 18.984147] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Broadcom BCM54140] (irq=POLL) <6>[ 19.089292] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Broadcom BCM54140] (irq=POLL) <6>[ 19.127107] device enp0s0f2 entered promiscuous mode <6>[ 19.169705] device enp0s0f6 entered promiscuous mode <6>[ 19.196976] DSA: tree 0 setup <6>[ 19.330961] mali-dp f080000.display: Adding to iommu group 15 <6>[ 19.368300] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 19.378422] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 19.394208] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 19.632066] caam_jr 8010000.jr: Adding to iommu group 16 <6>[ 19.654551] caam algorithms registered in /proc/crypto <6>[ 19.665187] caam 8000000.crypto: registering rng-caam <6>[ 19.673965] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 19.682559] caam_jr 8020000.jr: Adding to iommu group 17 <6>[ 19.690984] caam_jr 8030000.jr: Adding to iommu group 18 <6>[ 19.699741] caam_jr 8040000.jr: Adding to iommu group 19 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-467027/environment . /lava-467027/environment / # /lava-467027/bin/lava-test-runner /lava-467027/0 /lava-467027/bin/lava-test-runner /lava-467027/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-467027/0/tests/0_dmesg + cat uuid + UUID=467027_1.5.<8>[ 20.761692] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 20.858050] <8>[ 20.953815] <8>[ 21.054287] + set +x <8>[ 21.073780] / #