Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.76 (254 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 467205/tftp-deploy-idax1vnv/kernel/Image tftp 0x82000000 467205/tftp-deploy-idax1vnv/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.76; sending through gateway 172.16.0.254 Filename '467205/tftp-deploy-idax1vnv/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 9.2 MiB/s done Bytes transferred = 58176000 (377b200 hex) => tftp 0x90080000 467205/tftp-deploy-idax1vnv/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 467205/tftp-deploy-idax1vnv/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.76; sending through gateway 172.16.0.254 Filename '467205/tftp-deploy-idax1vnv/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 15.2 MiB/s done Bytes transferred = 28770309 (1b70005 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 467205/tftp-deploy-idax1vnv/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 467205/tftp-deploy-idax1vnv/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.76; sending through gateway 172.16.0.254 Filename '467205/tftp-deploy-idax1vnv/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 13.7 MiB/s done Bytes transferred = 28772 (7064 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-06-04 23:56:05 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 28770245 Bytes = 27.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a063 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.92-cip22 (KernelCI@build-j217155-arm64-gcc-10-defconfig-kselftest-s75t2) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Jun 4 23:39:49 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f5640-0x20ff7f7fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 32 pages/cpu s92768 r8192 d30112 u131072 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:on <6>[ 0.000000] mem auto-init: clearing system memory may take some time... <6>[ 0.000000] stackdepot hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3848916K/4126720K available (23424K kernel code, 7148K rwdata, 11840K rodata, 14272K init, 11463K bss, 245036K reserved, 32768K cma-reserved) <4>[ 0.000000] ********************************************************** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** This system shows unhashed kernel memory addresses ** <4>[ 0.000000] ** via the console, logs, and other interfaces. This ** <4>[ 0.000000] ** might reduce the security of your system. ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** If you see this message and you are not debugging ** <4>[ 0.000000] ** the kernel, report this immediately to your system ** <4>[ 0.000000] ** administrator! ** <4>[ 0.000000] ** ** <4>[ 0.000000] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.000000] ********************************************************** <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 66789 entries in 261 pages <6>[ 0.000000] ftrace: allocated 261 pages with 3 groups <6>[ 0.000000] trace event string verifier disabled <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080380000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080310000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080320000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.009153] Console: colour dummy device 80x25 <4>[ 0.013943] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.022044] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026458] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030960] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035636] ... CLASSHASH_SIZE: 4096 <4>[ 0.040313] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.045078] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049842] ... CHAINHASH_SIZE: 32768 <4>[ 0.054606] memory used by lock dependency info: 6365 kB <4>[ 0.060336] memory used for stack traces: 4224 kB <4>[ 0.065451] per task-struct memory footprint: 1920 bytes <6>[ 0.071311] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.082055] pid_max: default: 32768 minimum: 301 <6>[ 0.087341] LSM: Security Framework initializing <6>[ 0.092362] landlock: Up and running. <6>[ 0.096387] LSM support for eBPF active <6>[ 0.100840] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.108599] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.123018] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.130635] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.137341] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.144953] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.151644] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.159254] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.165945] Running RCU-tasks wait API self tests <6>[ 0.276208] rcu: Hierarchical SRCU implementation. <6>[ 0.281351] rcu: Max phase no-delay instances is 1000. <6>[ 0.286979] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.300698] Platform MSI: gic-its@6020000 domain created <6>[ 0.306524] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.314552] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.320904] EFI services will not be available. <6>[ 0.326377] smp: Bringing up secondary CPUs ... <6>[ 0.333053] Detected PIPT I-cache on CPU1 <6>[ 0.333158] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.333170] GICv3: CPU1: using allocated LPI pending table @0x0000002080330000 <6>[ 0.333214] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.333604] smp: Brought up 1 node, 2 CPUs <6>[ 0.364058] SMP: Total of 2 processors activated. <6>[ 0.369096] CPU features: detected: 32-bit EL0 Support <6>[ 0.374618] CPU features: detected: 32-bit EL1 Support <6>[ 0.380113] CPU features: detected: CRC32 instructions <6>[ 0.385684] CPU: All CPU(s) started at EL2 <6>[ 0.390117] alternatives: applying system-wide alternatives <6>[ 0.400270] devtmpfs: initialized <6>[ 0.420792] Callback from call_rcu_tasks_rude() invoked. <6>[ 0.451094] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.461242] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.480090] pinctrl core: initialized pinctrl subsystem <6>[ 0.489752] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.497419] SoC family: QorIQ LS1028A <6>[ 0.501380] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.509491] DMI not present or invalid. <6>[ 0.515684] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.525561] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.533333] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.542111] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.550628] audit: initializing netlink subsys (disabled) <5>[ 0.556871] audit: type=2000 audit(0.404:1): state=initialized audit_enabled=0 res=1 <6>[ 0.561746] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.564966] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.571607] cpuidle: using governor menu <6>[ 0.582812] Callback from call_rcu_tasks() invoked. <6>[ 0.583671] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.595251] ASID allocator initialised with 65536 entries <6>[ 0.608799] Serial: AMBA PL011 UART driver <4>[ 0.681231] KASLR disabled due to lack of seed <6>[ 0.745268] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.752518] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.759150] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.766387] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.772998] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.780129] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.786735] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.793867] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.808310] ACPI: Interpreter disabled. <6>[ 0.821582] iommu: Default domain type: Translated <6>[ 0.826806] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.835410] SCSI subsystem initialized <6>[ 0.841491] usbcore: registered new interface driver usbfs <6>[ 0.847585] usbcore: registered new interface driver hub <6>[ 0.853387] usbcore: registered new device driver usb <6>[ 0.861031] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.870704] i2c i2c-0: IMX I2C adapter registered <6>[ 0.877411] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.886216] i2c i2c-1: IMX I2C adapter registered <6>[ 0.892067] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.901155] i2c i2c-2: IMX I2C adapter registered <6>[ 0.908665] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.914037] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.923648] PTP clock support registered <6>[ 0.928439] EDAC MC: Ver: 3.0.0 <6>[ 0.938111] FPGA manager framework <6>[ 0.942515] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.951692] NET: Registered PF_ATMPVC protocol family <6>[ 0.957097] NET: Registered PF_ATMSVC protocol family <6>[ 0.963609] vgaarb: loaded <6>[ 0.967819] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.977342] VFS: Disk quotas dquot_6.6.0 <6>[ 0.981766] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.990264] pnp: PnP ACPI: disabled <6>[ 1.024249] NET: Registered PF_INET protocol family <6>[ 1.030120] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.042192] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 147456 bytes, linear) <6>[ 1.051661] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 1.059882] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.068396] TCP bind hash table entries: 32768 (order: 10, 4718592 bytes, vmalloc hugepage) <6>[ 1.086262] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.094148] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.102871] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.110783] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.119621] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 1.127540] RPC: Registered named UNIX socket transport module. <6>[ 1.133924] RPC: Registered udp transport module. <6>[ 1.138958] RPC: Registered tcp transport module. <6>[ 1.144022] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.150823] NET: Registered PF_XDP protocol family <6>[ 1.156042] PCI: CLS 0 bytes, default 64 <6>[ 1.161386] Unpacking initramfs... <6>[ 1.173339] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.192663] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.213490] kvm [1]: GICv3: no GICV resource entry <6>[ 1.227821] kvm [1]: disabling GICv2 emulation <6>[ 1.232625] kvm [1]: GIC system register CPU interface enabled <6>[ 1.255871] kvm [1]: vgic interrupt IRQ9 <6>[ 1.260289] kvm [1]: Hyp mode initialized successfully <5>[ 1.281620] Initialise system trusted keyrings <6>[ 1.304181] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.425423] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.437017] NFS: Registering the id_resolver key type <5>[ 1.442570] Key type id_resolver registered <5>[ 1.447121] Key type id_legacy registered <6>[ 1.452115] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.459245] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.468706] 9p: Installing v9fs 9p2000 file system support <6>[ 1.506894] NET: Registered PF_ALG protocol family <5>[ 1.512181] Key type asymmetric registered <5>[ 1.516645] Asymmetric key parser 'x509' registered <6>[ 1.522142] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.529967] io scheduler mq-deadline registered <6>[ 1.534834] io scheduler kyber registered <4>[ 1.540464] test_firmware: interface ready <6>[ 1.644751] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 1.664091] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 1.680009] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 1.699967] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 1.719983] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 1.735951] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 1.755960] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 1.775930] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 1.792102] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 1.812848] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 1.828023] pci_bus 0000:00: root bus resource [bus 00] <6>[ 1.833644] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 1.855948] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 1.871952] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 1.887985] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 1.903968] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 1.923939] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 1.939956] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 1.956050] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 1.972091] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.995879] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.015859] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.035851] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.059978] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 2.065948] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.095937] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.121132] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 2.136065] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.155878] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.179922] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 2.203932] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 2.223970] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 2.229868] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 2.255865] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 2.280837] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 2.287382] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.298250] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.309623] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 2.316503] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 2.323033] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.333894] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.345263] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 2.352142] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 2.358644] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.369488] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.380855] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 2.388056] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 2.394580] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.405510] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.416801] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.427732] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 2.434740] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 2.441242] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 2.452102] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 2.463470] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 2.471244] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 2.477911] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 2.487096] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 2.496427] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 2.504006] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 2.513821] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 2.521703] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 2.530818] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 2.539951] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 2.546235] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 3.178921] Freeing initrd memory: 28092K <3>[ 3.524028] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 3.530992] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.538064] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.543899] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.550434] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.561455] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.568045] pci 0001:00:00.0: supports D1 D2 <6>[ 3.572642] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.581248] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.588246] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.594297] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.602079] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.611034] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.620020] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 3.626284] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 4.634899] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 4.641740] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 4.648806] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 4.654640] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 4.663982] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 4.674962] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 4.681531] pci 0002:00:00.0: supports D1 D2 <6>[ 4.686127] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 4.694641] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 4.701639] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 4.711635] EINJ: ACPI disabled. <6>[ 4.799342] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 4.818361] printk: console [ttyS0] disabled <6>[ 4.823455] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.832829] printk: console [ttyS0] enabled <6>[ 4.832829] printk: console [ttyS0] enabled <6>[ 4.841835] printk: bootconsole [ns16550a0] disabled <6>[ 4.841835] printk: bootconsole [ns16550a0] disabled <6>[ 4.855511] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 4.866795] SuperH (H)SCI(F) driver initialized <6>[ 4.873343] msm_serial: driver initialized <6>[ 4.880111] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 4.909675] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 4.916461] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 4.921382] arm-smmu 5000000.iommu: stage 1 translation <5>[ 4.926997] arm-smmu 5000000.iommu: stage 2 translation <5>[ 4.932610] arm-smmu 5000000.iommu: nested translation <5>[ 4.938149] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 4.945618] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 4.952476] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 4.959227] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 4.965976] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 4.975336] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 5.011387] loop: module loaded <6>[ 5.017451] lkdtm: No crash points registered, enable through debugfs <4>[ 5.056335] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 5.069838] megasas: 07.719.03.00-rc1 <6>[ 5.088682] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 5.133255] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 5.163965] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 5.171138] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 5.176691] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 5.188213] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 5.200566] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 5.213048] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 5.224509] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 5.264144] thunder_xcv, ver 1.0 <6>[ 5.267922] thunder_bgx, ver 1.0 <6>[ 5.271661] nicpf, ver 1.0 <6>[ 5.278443] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 5.286318] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 5.399859] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 5.410568] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 5.417631] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 5.531877] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 5.539934] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 5.546924] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 5.659874] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 5.667898] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 5.676202] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 5.787879] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 5.827399] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 5.834338] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 5.842340] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 5.852157] pps pps0: new PPS source ptp0 <6>[ 5.859215] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 5.866841] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 5.872877] hclge is initializing <6>[ 5.876601] e1000: Intel(R) PRO/1000 Network Driver <6>[ 5.881778] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 5.888077] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 5.893369] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 5.899902] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 5.905638] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 5.911707] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 5.918283] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 5.925918] sky2: driver version 1.30 <6>[ 5.934241] VFIO - User Level meta-driver version: 0.3 <6>[ 5.942289] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 5.952709] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 5.972586] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 5.978699] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 5.987632] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 5.997573] xhci-hcd xhci-hcd.0.auto: irq 100, io mem 0x03110000 <6>[ 6.004944] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 6.010786] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 6.018794] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 6.029230] hub 1-0:1.0: USB hub found <6>[ 6.033513] hub 1-0:1.0: 1 port detected <6>[ 6.040033] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 6.051032] hub 2-0:1.0: USB hub found <6>[ 6.055217] hub 2-0:1.0: 1 port detected <6>[ 6.061508] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 6.067381] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 6.076165] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 6.085925] xhci-hcd xhci-hcd.1.auto: irq 99, io mem 0x03100000 <6>[ 6.093102] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 6.098927] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 6.106923] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 6.116258] hub 3-0:1.0: USB hub found <6>[ 6.120422] hub 3-0:1.0: 1 port detected <6>[ 6.126112] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 6.136850] hub 4-0:1.0: USB hub found <6>[ 6.141015] hub 4-0:1.0: 1 port detected <6>[ 6.148418] usbcore: registered new interface driver usb-storage <6>[ 6.167012] i2c_dev: i2c /dev entries driver <6>[ 6.192698] sp805-wdt c000000.watchdog: registration successful <6>[ 6.200100] sp805-wdt c010000.watchdog: registration successful <6>[ 6.217077] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 6.229197] sdhci: Secure Digital Host Controller Interface driver <6>[ 6.235709] sdhci: Copyright(c) Pierre Ossman <6>[ 6.242976] Synopsys Designware Multimedia Card Interface Driver <6>[ 6.253147] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.262413] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 6.268643] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.269605] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 6.291942] usb 1-1: new high-speed USB device number 2 using xhci-hcd <6>[ 6.303316] usbcore: registered new interface driver usbhid <6>[ 6.309222] usbhid: USB HID core driver <6>[ 6.313474] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 6.315438] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 6.346116] netem: version 1.3 <6>[ 6.351393] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.359196] IPv4 over IPsec tunneling driver <6>[ 6.369306] NET: Registered PF_INET6 protocol family <6>[ 6.381422] Segment Routing with IPv6 <6>[ 6.385562] In-situ OAM (IOAM) with IPv6 <6>[ 6.392725] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 6.403050] NET: Registered PF_PACKET protocol family <6>[ 6.412490] 9pnet: Installing 9P2000 support <5>[ 6.417342] Key type dns_resolver registered <6>[ 6.419023] mmc0: new HS400 MMC card at address 0001 <6>[ 6.421926] mpls_gso: MPLS GSO support <6>[ 6.431925] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 6.440872] registered taskstats version 1 <5>[ 6.445439] Loading compiled-in X.509 certificates <6>[ 6.449332] mmcblk0: p1 p2 <6>[ 6.457711] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 6.472294] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 6.486117] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (511:0) <6>[ 6.506856] hub 1-1:1.0: USB hub found <5>[ 6.507301] Loaded X.509 cert 'Build time autogenerated kernel key: 5df4961ba5457d62bcfd185f7358115b300c5dbc' <6>[ 6.511425] hub 1-1:1.0: 7 ports detected <6>[ 6.522042] ima: No TPM chip found, activating TPM-bypass! <6>[ 6.531856] ima: Allocated hash algorithm: sha1 <6>[ 6.536921] ima: No architecture policies found <6>[ 6.585882] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 6.604570] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 6.612127] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 6.619521] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 6.626758] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 6.633972] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 6.641087] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 6.756014] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 6.767193] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 4a:5b:6f:e8:3d:89 <6>[ 6.776060] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 32:db:8e:32:fa:64 <6>[ 6.800278] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 6.879323] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 6.968993] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 10.053364] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 10.061676] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.080053] Sending DHCP requests ., OK <6>[ 10.105256] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.76 <6>[ 10.113414] IP-Config: Complete: <6>[ 10.117049] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.76, mask=255.255.255.0, gw=172.16.0.254 <6>[ 10.127590] host=172.16.0.76, domain=lava.lan, nis-domain=(none) <6>[ 10.134669] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 10.134708] nameserver0=8.8.8.8 <6>[ 10.154937] clk: Disabling unused clocks <6>[ 10.159691] ALSA device list: <6>[ 10.163381] No soundcards found. <6>[ 10.221878] Freeing unused kernel memory: 14272K <6>[ 10.227119] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.591646] udevd[144]: starting version 3.2.9 <5>[ 11.607921] random: crng init done <27>[ 11.621036] udevd[144]: specified user 'tss' unknown <27>[ 11.626580] udevd[144]: specified group 'tss' unknown <30>[ 11.638026] udevd[145]: starting eudev-3.2.9 <6>[ 13.472948] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <6>[ 13.484378] fsl_ddr_edac acquired irq 111 for MC <6>[ 13.517739] fsl_ddr_edac MC err registered <27>[ 13.543521] udevd[155]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <28>[ 13.644183] udevd[155]: could not rename interface '8' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 13.686344] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 13.791946] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 13.803032] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 13.836187] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 13.847630] wm8904 2-001a: supply DCVDD not found, using dummy regulator <6>[ 13.906246] mscc_felix 0000:00:00.5: Adding to iommu group 13 <6>[ 13.913184] mscc_felix 0000:00:00.5: device is disabled, skipping <4>[ 13.922927] wm8904 2-001a: supply DBVDD not found, using dummy regulator <6>[ 13.927904] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 13.930454] wm8904 2-001a: supply AVDD not found, using dummy regulator <4>[ 13.937352] rtc-rv8803 0-0032: Voltage low, data is invalid. <4>[ 13.944433] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 13.957784] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 13.985019] wm8904 2-001a: revision A <4>[ 14.012062] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 14.028540] rtc-rv8803 0-0032: registered as rtc0 <4>[ 14.036550] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 14.071847] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 14.076421] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 14.089436] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 14.136507] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 14.174124] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 14.182348] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <4>[ 14.209692] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 14.467078] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 14.562611] CAN device driver interface <6>[ 14.786813] caam 8000000.crypto: Entropy delay = 3200 <6>[ 14.827971] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 14.848041] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 14.853574] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 14.860885] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 15.203045] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.213695] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 15.224535] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 15.254108] mali-dp f080000.display: Adding to iommu group 14 <6>[ 15.639211] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 15.650067] caam algorithms registered in /proc/crypto <6>[ 15.661491] caam 8000000.crypto: registering rng-caam <6>[ 15.669644] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 15.678875] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 15.687065] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 15.695761] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-467205/environment . /lava-467205/environment / # /lava-467205/bin/lava-test-runner /lava-467205/0 /lava-467205/bin/lava-test-runner /lava-467205/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-467205/0/tests/0_dmesg + cat uuid + UUID=467205_1.5.<8>[ 16.758042] 2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.854032] <8>[ 16.949886] <8>[ 17.046071] + set +x <8>[ 17.064332] / #