[Enter `^Ec?' for help] INFO: ARM GICv2 driver initialized NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.3.0.3 NOTICE: BL2: PRR is R-Car H3 Ver.3.0 NOTICE: BL2: Board is Starter Kit Premier Rev.2.1 NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: LCM state is CM NOTICE: AVS setting succeeded. DVFS_SetVID=0x53 NOTICE: BL2: DDR3200(rev.0.41) NOTICE: BL2: [COLD_BOOT] NOTICE: BL2: DRAM Split is 4ch(DDR f) NOTICE: BL2: QoS is default setting(rev.0.11) NOTICE: BL2: DRAM refresh interval 1.95 usec NOTICE: BL2: Periodic Write DQ Training NOTICE: BL2: CH0: 400000000 - 43fffffff, 1 GiB NOTICE: BL2: CH1: 500000000 - 53fffffff, 1 GiB NOTICE: BL2: CH2: 600000000 - 63fffffff, 1 GiB NOTICE: BL2: CH3: 700000000 - 73fffffff, 1 GiB NOTICE: BL2: Lossy Decomp areas NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570 NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0 NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0 NOTICE: BL2: FDT at 0xe6327e78 NOTICE: BL2: v2.8(debug): NOTICE: BL2: Built : 09:13:36, Jul 27 2023 NOTICE: BL2: Normal boot INFO: BL2: Doing platform setup INFO: BL2: Loading image id 3 NOTICE: BL2: dst=0xe6327700 src=0x8180000 len=512(0x200) NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800) WARNING: r-car ignoring the BL31 size from certificate,using RCAR_TRUSTED_SRAM_SIZE instead INFO: Loading image id=3 at address 0x44000000 NOTICE: rcar_file_len: len: 0x0003e000 NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=253952(0x3e000) INFO: Image id=3 loaded: 0x44000000 - 0x4403e000 INFO: BL2: Loading image id 4 INFO: Loading image id=4 at address 0x44100000 NOTICE: rcar_file_len: len: 0x00100000 NOTICE: BL2: dst=0x44100000 src=0x8200000 len=1048576(0x100000) INFO: Image id=4 loaded: 0x44100000 - 0x44200000 INFO: BL2: Loading image id 5 INFO: Loading image id=5 at address 0x50000000 NOTICE: rcar_file_len: len: 0x00100000 NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000) INFO: Image id=5 loaded: 0x50000000 - 0x50100000 NOTICE: BL2: Booting BL31 INFO: Entry point address = 0x44000000 INFO: SPSR = 0x3cd U-Boot 2023.01+dfsg-2+apertis3bv2024dev3b1 (Jul 27 2023 - 09:23:42 +0000) CPU: Renesas Electronics R8A7795 rev 3.0 Model: Renesas Starter Kit Premier board rev 2.1 DRAM: 896 MiB (effective 3.9 GiB) Core: 64 devices, 21 uclasses, devicetree: fit Flash: 0 Bytes MMC: sd@ee100000: 0, sd@ee140000: 1 Loading Environment from MMC... OK In: serial@e6e88000 Out: serial@e6e88000 Err: serial@e6e88000 Net: eth0: ethernet@e6800000 Auto-update from TFTP: failed, env. variable 'updatefile' not found Hit any key to stop autoboot: 2  0 => setenv autoload no => setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff => dhcp ethernet@e6800000 Waiting for PHY auto negotiation to complete.. done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.201.60 (260 ms) => setenv serverip 192.168.201.1 => tftp 0x68080000 14878943/tftp-deploy-vilm554j/kernel/Image Using ethernet@e6800000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.60 Filename '14878943/tftp-deploy-vilm554j/kernel/Image'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 19.3 MiB/s done Bytes transferred = 37900800 (2425200 hex) => tftp 0x4a000000 14878943/tftp-deploy-vilm554j/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@e6800000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.60 Filename '14878943/tftp-deploy-vilm554j/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4a000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################## 19.5 MiB/s done Bytes transferred = 22204200 (152cf28 hex) => setenv initrd_size ${filesize} => tftp 0x68000000 14878943/tftp-deploy-vilm554j/dtb/r8a779m1-ulcb.dtb Using ethernet@e6800000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.60 Filename '14878943/tftp-deploy-vilm554j/dtb/r8a779m1-ulcb.dtb'. Load address: 0x68000000 Loading: *##### 5.1 MiB/s done Bytes transferred = 70053 (111a5 hex) => setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x68080000 0x4a000000 0x68000000 Moving Image from 0x68080000 to 0x68200000, end=6a6d0000 ## Loading init Ramdisk from Legacy Image at 4a000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22204136 Bytes = 21.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Working FDT set to 68000000 Using Device Tree in place at 0000000068000000, end 00000000680141a4 Working FDT set to 68000000 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073] [ 0.000000] Linux version 6.1.96-cip24 (KernelCI@build-j272957-arm64-gcc-12-defconfig-zmngn) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Thu Jul 18 12:51:39 UTC 2024 [ 0.000000] Machine model: Renesas H3ULCB board based on r8a779m1 [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000054000000, size 48 MiB [ 0.000000] OF: reserved mem: initialized node lossy-decompression@54000000, compatible id shared-dma-pool [ 0.000000] earlycon: scif0 at MMIO 0x00000000e6e88000 (options '115200n8') [ 0.000000] printk: bootconsole [scif0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000073fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x73f7f3a00-0x73f7f5fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000048000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000073fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000048000000-0x0000000053ffffff] [ 0.000000] node 0: [mem 0x0000000054000000-0x0000000056ffffff] [ 0.000000] node 0: [mem 0x0000000057000000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000500000000-0x000000053fffffff] [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff] [ 0.000000] node 0: [mem 0x0000000700000000-0x000000073fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff] [ 0.000000] cma: Reserved 32 MiB at 0x000000007e000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 21 pages/cpu s47912 r8192 d29912 u86016 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999936 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 8. <6>[ 0.000000] software IO TLB: mapped [mem 0x000000007a000000-0x000000007e000000] (64MB) <6>[ 0.000000] Memory: 3777004K/4063232K available (16192K kernel code, 3732K rwdata, 9356K rodata, 7616K init, 609K bss, 253460K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns <6>[ 0.000001] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns <6>[ 0.008416] Console: colour dummy device 80x25 <6>[ 0.013159] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) <6>[ 0.023636] pid_max: default: 32768 minimum: 301 <6>[ 0.028531] LSM: Security Framework initializing <6>[ 0.033467] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041104] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050479] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.057955] cblist_init_generic: Setting shift to 3 and lim to 1. <6>[ 0.064332] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.071787] cblist_init_generic: Setting shift to 3 and lim to 1. <6>[ 0.078231] rcu: Hierarchical SRCU implementation. <6>[ 0.083267] rcu: Max phase no-delay instances is 1000. <6>[ 0.090172] Detected Renesas R-Car Gen3 r8a7795 ES3.0 <6>[ 0.096959] EFI services will not be available. <6>[ 0.102036] smp: Bringing up secondary CPUs ... <6>[ 0.107264] Detected PIPT I-cache on CPU1 <6>[ 0.107354] CPU1: Booted secondary processor 0x0000000001 [0x411fd073] <6>[ 0.107836] Detected PIPT I-cache on CPU2 <6>[ 0.107896] CPU2: Booted secondary processor 0x0000000002 [0x411fd073] <6>[ 0.108298] Detected PIPT I-cache on CPU3 <6>[ 0.108357] CPU3: Booted secondary processor 0x0000000003 [0x411fd073] <6>[ 0.108819] CPU features: detected: ARM erratum 845719 <6>[ 0.108833] Detected VIPT I-cache on CPU4 <6>[ 0.108950] CPU4: Booted secondary processor 0x0000000100 [0x410fd034] <6>[ 0.109389] Detected VIPT I-cache on CPU5 <6>[ 0.109461] CPU5: Booted secondary processor 0x0000000101 [0x410fd034] <6>[ 0.109882] Detected VIPT I-cache on CPU6 <6>[ 0.109957] CPU6: Booted secondary processor 0x0000000102 [0x410fd034] <6>[ 0.110392] Detected VIPT I-cache on CPU7 <6>[ 0.110471] CPU7: Booted secondary processor 0x0000000103 [0x410fd034] <6>[ 0.110540] smp: Brought up 1 node, 8 CPUs <6>[ 0.197229] SMP: Total of 8 processors activated. <6>[ 0.202171] CPU features: detected: 32-bit EL0 Support <6>[ 0.207553] CPU features: detected: 32-bit EL1 Support <6>[ 0.212929] CPU features: detected: CRC32 instructions <6>[ 0.218367] CPU: All CPU(s) started at EL1 <6>[ 0.222723] alternatives: applying system-wide alternatives <6>[ 0.230115] devtmpfs: initialized <6>[ 0.239770] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.249741] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) <6>[ 0.257692] pinctrl core: initialized pinctrl subsystem <6>[ 0.264890] DMI not present or invalid. <6>[ 0.269427] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.276326] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.283835] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.292033] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.300254] audit: initializing netlink subsys (disabled) <5>[ 0.306015] audit: type=2000 audit(0.228:1): state=initialized audit_enabled=0 res=1 <6>[ 0.307029] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.313992] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.320267] cpuidle: using governor menu <6>[ 0.331299] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.338439] ASID allocator initialised with 65536 entries <6>[ 0.345203] Serial: AMBA PL011 UART driver <6>[ 0.354496] platform soc: Fixed dependency cycle(s) with /soc/interrupt-controller@f1010000 <6>[ 0.364870] platform e6060000.pinctrl: Fixed dependency cycle(s) with /soc/pinctrl@e6060000/scif_clk <6>[ 0.374515] sh-pfc e6060000.pinctrl: r8a77951_pfc support registered <6>[ 0.387031] platform ec500000.sound: Fixed dependency cycle(s) with /soc/hdmi@fead0000 <6>[ 0.395179] platform ec500000.sound: Fixed dependency cycle(s) with /soc/i2c@e6510000/codec@10 <6>[ 0.409782] platform ec500000.sound: Fixed dependency cycle(s) with /soc/hdmi@fead0000 <6>[ 0.417967] platform fead0000.hdmi: Fixed dependency cycle(s) with /soc/sound@ec500000 <6>[ 0.426135] platform fead0000.hdmi: Fixed dependency cycle(s) with /soc/display@feb00000 <6>[ 0.434658] platform fead0000.hdmi: Fixed dependency cycle(s) with /soc/display@feb00000 <6>[ 0.442999] platform feb00000.display: Fixed dependency cycle(s) with /soc/hdmi@fead0000 <6>[ 0.451841] platform fead0000.hdmi: Fixed dependency cycle(s) with /hdmi0-out <6>[ 0.459239] platform hdmi0-out: Fixed dependency cycle(s) with /soc/hdmi@fead0000 <4>[ 0.468587] KASLR disabled due to lack of seed <6>[ 0.478070] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.485091] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.491586] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.498598] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.505091] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.512102] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.518594] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.525605] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.533330] ACPI: Interpreter disabled. <6>[ 0.541994] iommu: Default domain type: Translated <6>[ 0.547111] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.553831] SCSI subsystem initialized <6>[ 0.558062] usbcore: registered new interface driver usbfs <6>[ 0.563804] usbcore: registered new interface driver hub <6>[ 0.569364] usbcore: registered new device driver usb <6>[ 0.575769] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz <6>[ 0.583231] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.588431] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.597784] PTP clock support registered <6>[ 0.602052] EDAC MC: Ver: 3.0.0 <6>[ 0.606909] FPGA manager framework <6>[ 0.610602] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.617528] vgaarb: loaded <6>[ 0.620696] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.627178] VFS: Disk quotas dquot_6.6.0 <6>[ 0.631372] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.638587] pnp: PnP ACPI: disabled <6>[ 0.646993] NET: Registered PF_INET protocol family <6>[ 0.652315] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.661813] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.670611] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.678592] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.686874] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.695030] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.701888] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.708881] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.716395] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.722578] RPC: Registered named UNIX socket transport module. <6>[ 0.728737] RPC: Registered udp transport module. <6>[ 0.733676] RPC: Registered tcp transport module. <6>[ 0.738613] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.745285] PCI: CLS 0 bytes, default 64 <6>[ 0.749658] Unpacking initramfs... <6>[ 0.761548] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available <6>[ 0.770349] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available <6>[ 0.779160] kvm [1]: HYP mode not available <5>[ 0.784447] Initialise system trusted keyrings <6>[ 0.789277] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.799309] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.805903] NFS: Registering the id_resolver key type <5>[ 0.811241] Key type id_resolver registered <5>[ 0.815669] Key type id_legacy registered <6>[ 0.819999] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.826941] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.834789] 9p: Installing v9fs 9p2000 file system support <5>[ 0.866530] Key type asymmetric registered <5>[ 0.870888] Asymmetric key parser 'x509' registered <6>[ 0.876075] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.883708] io scheduler mq-deadline registered <6>[ 0.888478] io scheduler kyber registered <6>[ 0.903729] gpio_rcar e6050000.gpio: driving 16 GPIOs <6>[ 0.909390] gpio_rcar e6051000.gpio: driving 29 GPIOs <6>[ 0.915034] gpio_rcar e6052000.gpio: driving 15 GPIOs <6>[ 0.920658] gpio_rcar e6053000.gpio: driving 16 GPIOs <6>[ 0.926261] gpio_rcar e6054000.gpio: driving 18 GPIOs <6>[ 0.931869] gpio_rcar e6055000.gpio: driving 26 GPIOs <6>[ 0.937477] gpio_rcar e6055400.gpio: driving 32 GPIOs <6>[ 0.943087] gpio_rcar e6055800.gpio: driving 4 GPIOs <6>[ 0.951571] EINJ: ACPI disabled. <6>[ 0.974457] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 0.983429] SuperH (H)SCI(F) driver initialized <6>[ 0.988727] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 31, base_baud = 0) is a scif <6>[ 0.997292] printk: console [ttySC0] enabled <6>[ 0.997292] printk: console [ttySC0] enabled <6>[ 1.006363] printk: bootconsole [scif0] disabled <6>[ 1.006363] printk: bootconsole [scif0] disabled <6>[ 1.017168] msm_serial: driver initialized <6>[ 1.028074] loop: module loaded <6>[ 1.032658] megasas: 07.719.03.00-rc1 <6>[ 1.041705] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.047922] thunder_xcv, ver 1.0 <6>[ 1.051464] thunder_bgx, ver 1.0 <6>[ 1.054990] nicpf, ver 1.0 <6>[ 1.059198] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.066690] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.072332] hclge is initializing <6>[ 1.075931] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.081071] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.087131] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.092367] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.098587] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.104251] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.110119] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.116652] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.123458] sky2: driver version 1.30 <6>[ 1.128929] VFIO - User Level meta-driver version: 0.3 <6>[ 1.136660] ehci-platform ee0a0100.usb: EHCI Host Controller <6>[ 1.137115] ohci-platform ee0a0000.usb: Generic Platform OHCI controller <6>[ 1.137526] usbcore: registered new interface driver usb-storage <6>[ 1.139885] i2c_dev: i2c /dev entries driver <6>[ 1.141999] platform ec500000.sound: Fixed dependency cycle(s) with /soc/i2c@e6510000/codec@10 <6>[ 1.142059] i2c 2-0010: Fixed dependency cycle(s) with /soc/sound@ec500000 <6>[ 1.142341] cs2000-cp 2-004f: operating in static mode <6>[ 1.142630] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1 <6>[ 1.149576] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.150591] cs2000-cp 2-004f: revision - C1 <6>[ 1.150680] i2c-rcar e6510000.i2c: probed <6>[ 1.155932] ehci-platform ee0a0100.usb: irq 32, io mem 0xee0a0100 <6>[ 1.157142] i2c-rcar e66d8000.i2c: probed <6>[ 1.160432] ohci-platform ee0a0000.usb: irq 32, io mem 0xee0a0000 <6>[ 1.163875] rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points <6>[ 1.168142] rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points <6>[ 1.172399] rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 2 trip points <6>[ 1.188708] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10 <6>[ 1.198640] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.202824] hub 1-0:1.0: USB hub found <6>[ 1.206672] sdhci: Copyright(c) Pierre Ossman <6>[ 1.207617] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.213061] hub 1-0:1.0: 1 port detected <6>[ 1.218350] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.263444] hub 2-0:1.0: USB hub found <6>[ 1.288004] hub 2-0:1.0: 1 port detected <6>[ 1.288270] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.300174] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... <6>[ 1.307768] usbcore: registered new interface driver usbhid <6>[ 1.313612] usbhid: USB HID core driver <6>[ 1.324149] NET: Registered PF_PACKET protocol family <6>[ 1.329600] 9pnet: Installing 9P2000 support <5>[ 1.334192] Key type dns_resolver registered <6>[ 1.339137] registered taskstats version 1 <5>[ 1.343536] Loading compiled-in X.509 certificates <6>[ 1.362113] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs <6>[ 1.379750] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 1499999 KHz, changing to: 1500000 KHz <6>[ 1.390986] cpu cpu0: EM: created perf domain <6>[ 1.396919] cpufreq: cpufreq_online: CPU4: Running at unlisted initial frequency: 1199999 KHz, changing to: 1200000 KHz <6>[ 1.408103] cpu cpu4: EM: created perf domain <6>[ 1.429769] input: keyboard as /devices/platform/keyboard/input/input0 <6>[ 1.496531] Freeing initrd memory: 21676K <6>[ 13.744867] clk: Disabling unused clocks <6>[ 13.749916] ALSA device list: <6>[ 13.753163] No soundcards found. <6>[ 13.760203] Freeing unused kernel memory: 7616K <6>[ 13.765156] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.821704] udevd[169]: starting version 3.2.9 <5>[ 16.904702] random: crng init done <27>[ 16.911399] udevd[169]: specified user 'tss' unknown <27>[ 16.916782] udevd[169]: specified group 'tss' unknown <30>[ 16.923607] udevd[170]: starting eudev-3.2.9 <6>[ 17.147440] mc: Linux media interface: v0.10 <6>[ 17.163316] ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 <6>[ 17.180956] videodev: Linux video capture interface: v2.00 <6>[ 17.181245] ccree e6601000.crypto: ARM ccree device initialized <6>[ 17.208929] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY) <6>[ 17.219680] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver done Saving random seed: OK Starting network: OK Starting dropbear sshd: <6>[ 17.343905] NET: Registered PF_INET6 protocol family <6>[ 17.350196] Segment Routing with IPv6 <6>[ 17.354176] In-situ OAM (IOAM) with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # / # export SHELL=/bin/sh / # . /lava-14878943/environment / # /lava-14878943/bin/lava-test-runner /lava-14878943/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1487894<8>[ 22.898039] 3/0/tests/0_dmesg + cat uuid + UUID=14878943_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 22.920675] <8>[ 22.942276] <8>[ 22.963768] <8>[ 22.973578] + set +x / #