Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) Initializing DDR....using raw memory timing SPI boot Trying to boot from SPI U-Boot 2020.04-00169-g6acfd972fb (Mar 18 2021 - 21:55:22 +0100) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000103 00000000 100e7026 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 Board Hardware Variant: Single PHY (3) RCW: sl28-3-11_q.bin DRAM: Detected UDIMM Fixed DDR on board 3.9 GiB DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on) Using SERDES1 Protocol: 47960 (0xbb58) PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link CPLD: v18 WDT: Started with servicing (60s timeout) Waking secondary cores to start from fbd3c000 All (2) cores are up. MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPI Flash... SF: Detected w25q32jw with page size 256 Bytes, erase size 64 KiB, total 4 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial VPD: Using device 0x50 on I2C Bus 2 Net: eth0: enetc-0, eth2: enetc-2 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.75 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 483003/tftp-deploy-vuc3mgnj/kernel/Image tftp 0x82000000 483003/tftp-deploy-vuc3mgnj/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.75; sending through gateway 172.16.0.254 Filename '483003/tftp-deploy-vuc3mgnj/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 7.2 MiB/s done Bytes transferred = 37900800 (2425200 hex) => tftp 0x90080000 483003/tftp-deploy-vuc3mgnj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 483003/tftp-deploy-vuc3mgnj/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.75; sending through gateway 172.16.0.254 Filename '483003/tftp-deploy-vuc3mgnj/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 6.7 MiB/s done Bytes transferred = 22188293 (1529105 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 483003/tftp-deploy-vuc3mgnj/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb tftp 0x90000000 483003/tftp-deploy-vuc3mgnj/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.75; sending through gateway 172.16.0.254 Filename '483003/tftp-deploy-vuc3mgnj/dtb/fsl-ls1028a-kontron-sl28-var3-ads2.dtb'. Load address: 0x90000000 Loading: *## 9.1 MiB/s done Bytes transferred = 28772 (7064 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-07-18 13:04:59 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 22188229 Bytes = 21.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 000000009000a063 WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 6.1.96-cip24 (KernelCI@build-j272957-arm64-gcc-12-defconfig-zmngn) (aarch64-linux-gnu-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT Thu Jul 18 12:51:39 UTC 2024 [ 0.000000] Machine model: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7f6a00-0x20ff7f8fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] On node 0, zone Normal: 16896 pages in unavailable ranges [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] percpu: Embedded 21 pages/cpu s47912 r8192 d29912 u86016 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Fallback order for Node 0: 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1015296 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <5>[ 0.000000] Unknown kernel command line parameters \"n8\", will be passed to user space. <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: area num 2. <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) <6>[ 0.000000] Memory: 3888144K/4126720K available (16192K kernel code, 3732K rwdata, 9356K rodata, 7616K init, 609K bss, 205808K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] Root IRQ handler: gic_handle_irq <6>[ 0.000000] GICv3: GICv3 features: 16 PPIs <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000000] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008840] Console: colour dummy device 80x25 <6>[ 0.013634] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024353] pid_max: default: 32768 minimum: 301 <6>[ 0.029309] LSM: Security Framework initializing <6>[ 0.034301] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.042049] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.051077] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.058651] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.065107] cblist_init_generic: Setting adjustable number of callback queues. <6>[ 0.072669] cblist_init_generic: Setting shift to 1 and lim to 1. <6>[ 0.079190] rcu: Hierarchical SRCU implementation. <6>[ 0.084295] rcu: Max phase no-delay instances is 1000. <6>[ 0.089968] Platform MSI: gic-its@6020000 domain created <6>[ 0.095671] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.103531] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.109746] EFI services will not be available. <6>[ 0.114684] smp: Bringing up secondary CPUs ... <6>[ 0.119792] Detected PIPT I-cache on CPU1 <6>[ 0.119842] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.119851] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.119876] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.119930] smp: Brought up 1 node, 2 CPUs <6>[ 0.150248] SMP: Total of 2 processors activated. <6>[ 0.155260] CPU features: detected: 32-bit EL0 Support <6>[ 0.160717] CPU features: detected: 32-bit EL1 Support <6>[ 0.166168] CPU features: detected: CRC32 instructions <6>[ 0.171652] CPU: All CPU(s) started at EL2 <6>[ 0.176057] alternatives: applying system-wide alternatives <6>[ 0.183022] devtmpfs: initialized <6>[ 0.189923] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.200046] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.207753] pinctrl core: initialized pinctrl subsystem <6>[ 0.213690] Machine: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier <6>[ 0.221335] SoC family: QorIQ LS1028A <6>[ 0.225288] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.230576] DMI not present or invalid. <6>[ 0.235125] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.241947] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.249441] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.257672] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.265959] audit: initializing netlink subsys (disabled) <5>[ 0.271783] audit: type=2000 audit(0.164:1): state=initialized audit_enabled=0 res=1 <6>[ 0.272371] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.279869] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.286296] cpuidle: using governor menu <6>[ 0.297486] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.304631] ASID allocator initialised with 65536 entries <6>[ 0.311203] Serial: AMBA PL011 UART driver <4>[ 0.325869] KASLR disabled due to lack of seed <6>[ 0.335456] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.342580] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.349174] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.356290] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page <6>[ 0.362879] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.369992] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.376580] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.383694] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page <6>[ 0.391230] ACPI: Interpreter disabled. <6>[ 0.396653] iommu: Default domain type: Translated <6>[ 0.401843] iommu: DMA domain TLB invalidation policy: strict mode <5>[ 0.408566] SCSI subsystem initialized <6>[ 0.412821] usbcore: registered new interface driver usbfs <6>[ 0.418644] usbcore: registered new interface driver hub <6>[ 0.424284] usbcore: registered new device driver usb <6>[ 0.429939] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.437742] i2c i2c-0: IMX I2C adapter registered <6>[ 0.442948] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.450604] i2c i2c-1: IMX I2C adapter registered <6>[ 0.455718] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.463436] i2c i2c-2: IMX I2C adapter registered <6>[ 0.468876] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.474151] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.483650] PTP clock support registered <6>[ 0.487938] EDAC MC: Ver: 3.0.0 <6>[ 0.492252] FPGA manager framework <6>[ 0.495995] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.502814] vgaarb: loaded <6>[ 0.505982] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.512527] VFS: Disk quotas dquot_6.6.0 <6>[ 0.516775] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.524069] pnp: PnP ACPI: disabled <6>[ 0.531527] NET: Registered PF_INET protocol family <6>[ 0.536930] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.546682] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.555608] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.563704] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.572054] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) <6>[ 0.580435] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.587397] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.594469] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.602059] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 0.608325] RPC: Registered named UNIX socket transport module. <6>[ 0.614576] RPC: Registered udp transport module. <6>[ 0.619587] RPC: Registered tcp transport module. <6>[ 0.624596] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.631375] PCI: CLS 0 bytes, default 64 <6>[ 0.635691] Unpacking initramfs... <6>[ 0.639711] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 0.648515] kvm [1]: IPA Size Limit: 44 bits <6>[ 0.654014] kvm [1]: GICv3: no GICV resource entry <6>[ 0.659122] kvm [1]: disabling GICv2 emulation <6>[ 0.663880] kvm [1]: GIC system register CPU interface enabled <6>[ 0.670080] kvm [1]: vgic interrupt IRQ9 <6>[ 0.674353] kvm [1]: Hyp mode initialized successfully <5>[ 0.680459] Initialise system trusted keyrings <6>[ 0.685350] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 0.695696] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 0.702299] NFS: Registering the id_resolver key type <5>[ 0.707705] Key type id_resolver registered <5>[ 0.712207] Key type id_legacy registered <6>[ 0.716593] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 0.723630] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 0.731503] 9p: Installing v9fs 9p2000 file system support <5>[ 0.767675] Key type asymmetric registered <5>[ 0.772080] Asymmetric key parser 'x509' registered <6>[ 0.777315] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 0.785056] io scheduler mq-deadline registered <6>[ 0.789893] io scheduler kyber registered <6>[ 0.801096] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 0.809340] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x01f8000000 <6>[ 0.818519] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x01f8160000 <6>[ 0.827697] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x01f81d0000 <6>[ 0.836869] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x01f81f0000 <6>[ 0.846041] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x01f8210000 <6>[ 0.855216] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x01f8230000 <6>[ 0.864379] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x01fc000000 <6>[ 0.873594] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 0.882768] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 0.890088] pci_bus 0000:00: root bus resource [bus 00] <6>[ 0.895643] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] <6>[ 0.903054] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] <6>[ 0.910895] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] <6>[ 0.918300] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] <6>[ 0.926139] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] <6>[ 0.933536] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] <6>[ 0.941376] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] <6>[ 0.948802] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 0.955187] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 0.966018] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 0.977285] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 0.988385] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 0.999957] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 1.005780] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.016080] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.027001] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 1.033379] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.044207] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.055475] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 1.066567] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 1.078110] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 1.083935] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 1.094234] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 1.105158] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 1.111544] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.122380] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.133663] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 1.139663] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 1.146045] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.156874] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.168158] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 1.174140] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 1.180505] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.191325] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.202586] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 1.208578] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 1.214940] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.225750] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.236997] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.247818] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 1.253827] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 1.260190] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 1.271002] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 1.282262] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 1.288972] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 1.295392] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 1.303414] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <6>[ 1.311567] pcieport 0000:00:1f.0: PME: Signaling with IRQ 20 <6>[ 1.317860] pcieport 0000:00:1f.0: AER: enabled with IRQ 20 <6>[ 1.324441] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 1.332121] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 1.341025] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 1.349960] layerscape-pcie 3400000.pcie: iATU unroll: disabled <6>[ 1.356204] layerscape-pcie 3400000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <6>[ 1.394519] Freeing initrd memory: 21664K <3>[ 2.364562] layerscape-pcie 3400000.pcie: Phy link never came up <6>[ 2.371021] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 2.378056] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 2.383858] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 2.390362] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 2.401274] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 2.407664] pci 0001:00:00.0: supports D1 D2 <6>[ 2.412237] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 2.419493] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 2.426448] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 2.431859] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 2.439529] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 2.448412] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 2.457322] layerscape-pcie 3500000.pcie: iATU unroll: disabled <6>[ 2.463562] layerscape-pcie 3500000.pcie: iATU regions: 8 ob, 6 ib, align 4K, limit 4G <3>[ 3.471911] layerscape-pcie 3500000.pcie: Phy link never came up <6>[ 3.478295] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.485327] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.491129] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.500442] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.511347] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.517728] pci 0002:00:00.0: supports D1 D2 <6>[ 3.522301] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.529479] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.536430] pci 0002:00:00.0: PCI bridge to [bus 01] <6>[ 3.542476] EINJ: ACPI disabled. <6>[ 3.559233] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.567488] printk: console [ttyS0] disabled <6>[ 3.572112] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 3.581278] printk: console [ttyS0] enabled <6>[ 3.581278] printk: console [ttyS0] enabled <6>[ 3.590225] printk: bootconsole [ns16550a0] disabled <6>[ 3.590225] printk: bootconsole [ns16550a0] disabled <6>[ 3.601063] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 21, base_baud = 12500000) is a 16550A <6>[ 3.610508] SuperH (H)SCI(F) driver initialized <6>[ 3.615627] msm_serial: driver initialized <6>[ 3.620412] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 22, base_baud = 12500000) is a FSL_LPUART <5>[ 3.632068] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.638817] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.643715] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.649306] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.654896] arm-smmu 5000000.iommu: nested translation <5>[ 3.660402] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.667830] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.674650] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.681376] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.688101] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <5>[ 3.695042] arm-smmu 5000000.iommu: preserved 0 boot mappings <6>[ 3.704349] loop: module loaded <4>[ 3.713345] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 3.723339] megasas: 07.719.03.00-rc1 <6>[ 3.729438] spi-nor spi1.0: w25q128fw (16384 Kbytes) <6>[ 3.748812] spi-nor spi0.0: w25q32jwm (4096 Kbytes) <5>[ 3.766027] 5 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 3.773143] Creating 5 MTD partitions on \"20c0000.spi\": <5>[ 3.778650] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 3.784273] 0x000000010000-0x0000001e0000 : \"failsafe bootloader\" <5>[ 3.791212] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 3.798146] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 3.804261] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 3.813596] tun: Universal TUN/TAP device driver, 1.6 <6>[ 3.819552] thunder_xcv, ver 1.0 <6>[ 3.823081] thunder_bgx, ver 1.0 <6>[ 3.826605] nicpf, ver 1.0 <6>[ 3.830141] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 3.836211] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 3.950001] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 3.957386] fsl_enetc 0000:00:00.1: device is disabled, skipping <6>[ 3.963754] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 4.073992] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 4.080789] fsl_enetc 0000:00:00.2: device is disabled, skipping <6>[ 4.087154] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 4.197995] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 4.204792] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 4.211423] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 4.321998] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.343388] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 4.349701] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.356637] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.365654] pps pps0: new PPS source ptp0 <6>[ 4.370469] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.377992] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.383627] hclge is initializing <6>[ 4.387223] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.392379] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.398435] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.403678] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.409908] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.415588] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.421460] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.428015] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.434455] sky2: driver version 1.30 <6>[ 4.439117] VFIO - User Level meta-driver version: 0.3 <6>[ 4.444939] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 4.451153] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 4.458835] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.464624] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.472703] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 4.482424] xhci-hcd xhci-hcd.0.auto: irq 99, io mem 0x03100000 <6>[ 4.488717] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.494489] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.502439] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.509570] hub 1-0:1.0: USB hub found <6>[ 4.513612] hub 1-0:1.0: 1 port detected <6>[ 4.517984] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.526606] hub 2-0:1.0: USB hub found <6>[ 4.530647] hub 2-0:1.0: 1 port detected <6>[ 4.535046] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.540827] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 4.548891] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000008002010010 <6>[ 4.558610] xhci-hcd xhci-hcd.1.auto: irq 100, io mem 0x03110000 <6>[ 4.564996] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 4.570771] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 4.578722] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 4.585792] hub 3-0:1.0: USB hub found <6>[ 4.589832] hub 3-0:1.0: 1 port detected <6>[ 4.594191] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 4.602805] hub 4-0:1.0: USB hub found <6>[ 4.606845] hub 4-0:1.0: 1 port detected <6>[ 4.611577] usbcore: registered new interface driver usb-storage <6>[ 4.619787] i2c_dev: i2c /dev entries driver <6>[ 4.627760] sp805-wdt c000000.watchdog: registration successful <6>[ 4.634127] sp805-wdt c010000.watchdog: registration successful <6>[ 4.641909] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 4.650774] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.657265] sdhci: Copyright(c) Pierre Ossman <6>[ 4.662413] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.669357] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.675884] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 4.681865] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.682106] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 4.695917] usbcore: registered new interface driver usbhid <6>[ 4.701793] usbhid: USB HID core driver <6>[ 4.710215] NET: Registered PF_PACKET protocol family <6>[ 4.715641] 9pnet: Installing 9P2000 support <6>[ 4.718002] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <5>[ 4.720353] Key type dns_resolver registered <6>[ 4.727375] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 4.732112] registered taskstats version 1 <5>[ 4.743545] Loading compiled-in X.509 certificates <6>[ 4.752682] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 4.760602] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 4.766672] pcieport 0001:00:00.0: PME: Signaling with IRQ 104 <6>[ 4.772988] pcieport 0001:00:00.0: AER: enabled with IRQ 104 <6>[ 4.779189] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 4.785252] pcieport 0002:00:00.0: PME: Signaling with IRQ 105 <6>[ 4.791542] pcieport 0002:00:00.0: AER: enabled with IRQ 105 <6>[ 4.870012] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 4.885823] mmc0: new HS400 MMC card at address 0001 <6>[ 4.891818] mmcblk0: mmc0:0001 S0J56X 7.34 GiB <6>[ 4.897922] mmcblk0: p1 p2 <6>[ 4.901423] mmcblk0boot0: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.902006] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.907619] mmcblk0boot1: mmc0:0001 S0J56X 31.5 MiB <6>[ 4.914171] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using aa:0d:95:72:a4:80 <6>[ 4.919178] mmcblk0rpmb: mmc0:0001 S0J56X 4.00 MiB, chardev (234:0) <6>[ 4.927232] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using ca:52:ec:d2:02:a9 <6>[ 4.946062] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 4.987451] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.3:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.012987] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.065727] hub 3-1:1.0: USB hub found <6>[ 5.069850] hub 3-1:1.0: 7 ports detected <6>[ 8.098963] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 8.126030] Sending DHCP requests ., OK <6>[ 8.146286] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.75 <6>[ 8.154296] IP-Config: Complete: <6>[ 8.157804] device=eth0, hwaddr=00:e0:4b:6e:9b:2b, ipaddr=172.16.0.75, mask=255.255.255.0, gw=172.16.0.254 <6>[ 8.168240] host=172.16.0.75, domain=lava.lan, nis-domain=(none) <6>[ 8.175010] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.175028] nameserver0=8.8.8.8 <6>[ 8.185899] clk: Disabling unused clocks <6>[ 8.190227] ALSA device list: <6>[ 8.193471] No soundcards found. <6>[ 8.201075] Freeing unused kernel memory: 7616K <6>[ 8.206064] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.272213] udevd[132]: starting version 3.2.9 <5>[ 9.285987] random: crng init done <27>[ 9.292572] udevd[132]: specified user 'tss' unknown <27>[ 9.297970] udevd[132]: specified group 'tss' unknown <30>[ 9.304389] udevd[133]: starting eudev-3.2.9 <6>[ 9.573160] EDAC MC0: Giving out device to module fsl_ddr_edac controller fsl_mc_err: DEV fsl_mc_err (INTERRUPT) <27>[ 9.579089] udevd[141]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <4>[ 9.611345] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.618378] NET: Registered PF_INET6 protocol family <6>[ 9.623821] fsl_ddr_edac acquired irq 111 for MC <28>[ 9.623875] udevd[141]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 9.628918] fsl_ddr_edac MC err registered <6>[ 9.642982] Segment Routing with IPv6 <4>[ 9.645125] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <6>[ 9.647084] In-situ OAM (IOAM) with IPv6 <4>[ 9.654732] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 9.665528] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 9.673166] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. <4>[ 9.674789] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 9.700910] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 9.717228] mscc_felix 0000:00:00.5: Adding to iommu group 13 <4>[ 9.738991] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 9.739407] mscc_felix 0000:00:00.5: device is disabled, skipping <6>[ 9.751490] rtc-rv8803 0-0032: registered as rtc0 <6>[ 9.751889] at24 1-0057: 8192 byte 24c64 EEPROM, writable, 32 bytes/write <4>[ 9.764313] rtc-rv8803 0-0032: Voltage low, data is invalid. <3>[ 9.770307] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <4>[ 9.770582] wm8904 2-001a: supply DCVDD not found, using dummy regulator <4>[ 9.782101] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 9.790349] wm8904 2-001a: supply DBVDD not found, using dummy regulator <4>[ 9.798717] wm8904 2-001a: supply AVDD not found, using dummy regulator <6>[ 9.805933] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 9.806863] wm8904 2-001a: supply CPVDD not found, using dummy regulator <4>[ 9.821816] wm8904 2-001a: supply MICVDD not found, using dummy regulator <6>[ 9.830203] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 9.839133] wm8904 2-001a: revision A <4>[ 9.851924] simple-mfd-i2c 0-004a: mask_invert=true is deprecated; please switch to unmask_base <6>[ 9.868974] CAN device driver interface <6>[ 9.875250] ftm-alarm 2800000.timer: registered as rtc1 <6>[ 9.909681] caam 8000000.crypto: Entropy delay = 3200 <6>[ 9.967064] caam 8000000.crypto: Instantiated RNG4 SH0 <6>[ 10.008698] caam 8000000.crypto: Instantiated RNG4 SH1 <6>[ 10.014538] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 10.021614] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 10.038819] etnaviv etnaviv: bound f0c0000.gpu (ops gpu_ops [etnaviv]) <6>[ 10.043303] mali-dp f080000.display: Adding to iommu group 14 <6>[ 10.046250] etnaviv-gpu f0c0000.gpu: model: GC7000, revision: 6202 <6>[ 10.059585] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 10.076414] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 10.085459] caam algorithms registered in /proc/crypto <6>[ 10.091766] caam 8000000.crypto: registering rng-caam <6>[ 10.097284] caam 8000000.crypto: rng crypto API alg registered prng-caam <6>[ 10.104928] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 10.111360] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 10.117802] caam_jr 8040000.jr: Adding to iommu group 18 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-483003/environment . /lava-483003/environment / # /lava-483003/bin/lava-test-runner /lava-483003/0 /lava-483003/bin/lava-test-runner /lava-483003/0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 10.708006] d /lava-483003/0/tests/0_dmesg + cat uuid + UUID=483003_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.728805] <8>[ 10.750124] <8>[ 10.772530] + set +x <8>[ 10.782546] / #