[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Couldn't find partition mmc 0:1 Error selecting device File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 8794305/tftp-deploy-c0rjqmzz/kernel/zImage tftp 0x10000000 8794305/tftp-deploy-c0rjqmzz/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '8794305/tftp-deploy-c0rjqmzz/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 11.7 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 8794305/tftp-deploy-c0rjqmzz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8794305/tftp-deploy-c0rjqmzz/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '8794305/tftp-deploy-c0rjqmzz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 11.9 MiB/s done Bytes transferred = 13340039 (cb8d87 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8794305/tftp-deploy-c0rjqmzz/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8794305/tftp-deploy-c0rjqmzz/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '8794305/tftp-deploy-c0rjqmzz/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.6 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13339975 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.270-cip88 (KernelCI@build-j880901-arm-gcc-10-multi-v7-defconfig-sn2wb) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Thu Jan 19 09:16:32 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939136K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43904K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021429] Console: colour dummy device 80x30 <6>[ 0.023312] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033731] pid_max: default: 32768 minimum: 301 <6>[ 0.038724] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045476] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053312] CPU: Testing write buffer coherency: ok <6>[ 0.057920] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063570] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069806] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077543] rcu: Hierarchical SRCU implementation. <6>[ 0.084084] EFI services will not be available. <6>[ 0.086323] smp: Bringing up secondary CPUs ... <6>[ 0.091587] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091593] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102925] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102931] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114115] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114120] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124590] smp: Brought up 1 node, 4 CPUs <6>[ 0.128842] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135261] CPU: All CPU(s) started in SVC mode. <6>[ 0.141235] devtmpfs: initialized <6>[ 0.150896] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156344] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166098] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.176243] pinctrl core: initialized pinctrl subsystem <6>[ 0.180478] DMI not present or invalid. <6>[ 0.183774] NET: Registered protocol family 16 <6>[ 0.191090] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197710] cpuidle: using governor menu <6>[ 0.199716] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214636] vdd1p1: supplied by regulator-dummy <6>[ 0.217107] vdd3p0: supplied by regulator-dummy <6>[ 0.221833] vdd2p5: supplied by regulator-dummy <6>[ 0.226678] vddarm: supplied by regulator-dummy <6>[ 0.231578] vddpu: supplied by regulator-dummy <6>[ 0.236020] vddsoc: supplied by regulator-dummy <6>[ 0.254518] No ATAGs? <6>[ 0.254662] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262622] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.272071] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278951] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290798] Serial: AMBA PL011 UART driver <6>[ 0.294640] console [pstore-1] enabled <6>[ 0.296498] pstore: Registered ramoops as persistent store backend <6>[ 0.302746] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331028] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340500] vgaarb: loaded <5>[ 0.341410] SCSI subsystem initialized <6>[ 0.345023] usbcore: registered new interface driver usbfs <6>[ 0.350465] usbcore: registered new interface driver hub <6>[ 0.355985] usbcore: registered new device driver usb <6>[ 0.362474] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366219] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372325] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376742] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382686] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387267] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394349] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398049] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407457] PTP clock support registered <6>[ 0.411843] EDAC MC: Ver: 3.0.0 <6>[ 0.417778] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.480461] NET: Registered protocol family 2 <6>[ 0.482684] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.490203] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.497138] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.504531] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.511278] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.517966] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.523940] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.530696] NET: Registered protocol family 1 <6>[ 0.535664] RPC: Registered named UNIX socket transport module. <6>[ 0.541334] RPC: Registered udp transport module. <6>[ 0.546262] RPC: Registered tcp transport module. <6>[ 0.551239] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.558416] Trying to unpack rootfs image as initramfs... <6>[ 1.671558] Freeing initrd memory: 13028K <4>[ 1.673425] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.680733] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.690673] Initialise system trusted keyrings <6>[ 1.693687] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.706203] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.710104] NFS: Registering the id_resolver key type <5>[ 1.714799] Key type id_resolver registered <5>[ 1.719220] Key type id_legacy registered <6>[ 1.723489] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.730285] Key type asymmetric registered <5>[ 1.732418] Asymmetric key parser 'x509' registered <6>[ 1.737592] bounce: pool size: 64 pages <6>[ 1.741692] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.749310] io scheduler noop registered <6>[ 1.753470] io scheduler deadline registered <6>[ 1.758138] io scheduler cfq registered (default) <6>[ 1.762954] io scheduler mq-deadline registered <6>[ 1.767735] io scheduler kyber registered <6>[ 1.793787] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.798334] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.805436] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.812751] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.832861] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.836251] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.844105] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.850308] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.858227] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.867800] PU : no governor for states <6>[ 1.867822] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.871870] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.936929] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.944252] SuperH (H)SCI(F) driver initialized <6>[ 1.947102] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.955878] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.966831] console [ttymxc1] enabled <6>[ 1.966831] console [ttymxc1] enabled <6>[ 1.971830] bootconsole [ec_imx21] disabled <6>[ 1.971830] bootconsole [ec_imx21] disabled <6>[ 1.981920] msm_serial: driver initialized <6>[ 1.988181] STMicroelectronics ASC driver initialized <6>[ 1.995328] STM32 USART driver initialized <4>[ 2.010602] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.019304] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.026262] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.033030] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.042058] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.049220] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.063945] brd: module loaded <6>[ 2.076839] loop: module loaded <6>[ 2.083436] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.091684] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.099973] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.108437] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.119219] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.126477] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.135566] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.146360] scsi host0: ahci-imx <6>[ 2.150465] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.169406] CAN device driver interface <6>[ 2.174751] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.181843] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.190806] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.199893] pps pps0: new PPS source ptp0 <6>[ 2.230635] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.238098] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.244199] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.250465] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.257694] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.269431] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.277136] usbcore: registered new interface driver pegasus <6>[ 2.283127] usbcore: registered new interface driver asix <6>[ 2.288842] usbcore: registered new interface driver ax88179_178a <6>[ 2.295232] usbcore: registered new interface driver cdc_ether <6>[ 2.301389] usbcore: registered new interface driver smsc75xx <6>[ 2.307448] usbcore: registered new interface driver smsc95xx <6>[ 2.313511] usbcore: registered new interface driver net1080 <6>[ 2.319490] usbcore: registered new interface driver cdc_subset <6>[ 2.325708] usbcore: registered new interface driver zaurus <6>[ 2.331626] usbcore: registered new interface driver cdc_ncm <6>[ 2.340523] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.347319] ehci-pci: EHCI PCI platform driver <6>[ 2.352097] ehci-platform: EHCI generic platform driver <6>[ 2.357917] ehci-orion: EHCI orion driver <6>[ 2.362417] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.366878] ehci-st: EHCI STMicroelectronics driver <6>[ 2.372237] ehci-exynos: EHCI EXYNOS driver <6>[ 2.376870] ehci-atmel: EHCI Atmel driver <6>[ 2.381347] tegra-ehci: Tegra EHCI driver <6>[ 2.385844] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.392322] ohci-pci: OHCI PCI platform driver <6>[ 2.397077] ohci-platform: OHCI generic platform driver <6>[ 2.402855] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.407330] ohci-st: OHCI STMicroelectronics driver <6>[ 2.412686] ohci-atmel: OHCI Atmel driver <6>[ 2.417968] usbcore: registered new interface driver usb-storage <6>[ 2.426524] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.438595] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.448717] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.453887] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.487805] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.489301] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.494148] hub 1-0:1.0: USB hub found <6>[ 2.499193] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.503209] hub 1-0:1.0: 1 port detected <6>[ 2.509718] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.520139] i2c /dev entries driver <6>[ 2.539619] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.551039] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.557487] sdhci: Copyright(c) Pierre Ossman <6>[ 2.564379] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.572667] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.579478] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.584915] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.590439] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.630248] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.638280] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.643802] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.683670] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.695085] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.702151] usbcore: registered new interface driver usbhid <6>[ 2.708015] usbhid: USB HID core driver <6>[ 2.718097] NET: Registered protocol family 10 <6>[ 2.723946] Segment Routing with IPv6 <6>[ 2.727995] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.734744] NET: Registered protocol family 17 <6>[ 2.739497] can: controller area network core (rev 20170425 abi 9) <6>[ 2.746010] NET: Registered protocol family 29 <6>[ 2.750744] can: raw protocol (rev 20170425) <6>[ 2.755284] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.761236] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.767353] Key type dns_resolver registered <6>[ 2.772906] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.778661] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.784403] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.790883] ThumbEE CPU extension supported. <5>[ 2.795430] Registering SWP/SWPB emulation handler <5>[ 2.801788] Loading compiled-in X.509 certificates <6>[ 2.808343] pstore: Using compression: deflate <6>[ 2.829464] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.836844] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.845382] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.853910] mmc0: new high speed SDHC card at address 59b4 <6>[ 2.859913] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.868620] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.877299] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.885557] mmcblk0: mmc0:59b4 SD 14.7 GiB <6>[ 2.890564] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.897674] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.905885] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.914929] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.922200] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.931049] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.941610] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.949113] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.957421] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.965010] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.973609] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.982300] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.989522] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.997380] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.006422] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.013663] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.021604] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.029105] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.037316] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.044890] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.053436] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.062130] panel-simple panel-lcd: Linked as a consumer to regulator.0 <4>[ 3.069176] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.076838] GPT:29296874 != 30863359 <4>[ 3.080700] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.086970] GPT:29296874 != 30863359 <4>[ 3.090826] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.096262] mmcblk0: p1 p2 p3 <6>[ 3.099771] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.107618] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.116658] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.123926] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.134028] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.142906] hctosys: unable to open rtc device (rtc0) <6>[ 3.149489] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.156911] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.165727] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.173238] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.181897] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.190605] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.197875] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.205758] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.214818] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.222043] hub 1-1:1.0: USB hub found <6>[ 3.226135] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.233416] hub 1-1:1.0: 3 ports detected <6>[ 3.239244] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.246620] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.254842] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.262319] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.270836] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.278401] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.279512] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.294287] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.301103] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.315002] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.324029] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.331147] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.398449] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.417814] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.447858] Sending DHCP requests ., OK <6>[ 6.491999] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 6.500346] IP-Config: Complete: <6>[ 6.503864] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.514612] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 6.522752] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.522762] nameserver0=192.168.201.1 <6>[ 6.541697] Freeing unused kernel memory: 2048K <6>[ 6.558169] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.689277] udevd[108]: starting version 3.2.9 <5>[ 6.694820] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.701823] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.708671] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.722403] udevd[108]: specified user 'tss' unknown <27>[ 6.727898] udevd[108]: specified group 'tss' unknown <30>[ 6.735317] udevd[109]: starting eudev-3.2.9 <6>[ 7.020705] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.032645] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.042082] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.053651] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.061834] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.070853] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.078119] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.079990] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.087150] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.093535] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.097878] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.097891] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.121362] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.130000] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.139065] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.146196] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.154309] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.161749] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.170533] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.178056] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.187199] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.195939] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.202969] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.230286] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 7.238005] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.238928] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.253383] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.260576] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.266967] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.271516] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.275468] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.283384] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.286366] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.302995] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.310501] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.320219] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.328968] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.335932] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.344356] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.353509] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.360711] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.369187] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.376567] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.385991] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.393517] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.403001] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.411773] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.418801] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 7.453285] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.459701] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.469965] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 7.478755] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.491376] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.498601] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.506940] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.519523] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.528513] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.538427] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.547360] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.556104] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.563155] panel-simple panel-lcd: Dropping the link to regulator.0 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8794305/environment . /lava-8794305/environment / # /lava-8794305/bin/lava-test-runner /lava-8794305/0 /lava-8794305/bin/lava-test-runner /lava-8794305/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-8794305/0/tests/0_dmesg + cat uuid + UUID=8794305_1<8>[ 8.269405] .5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.314910] <8>[ 8.355082] <8>[ 8.395456] + set +x <8>[ 8.405375] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-8794305/environment / # . /lava-8794305/environment/lava-8794305/bin/lava-test-runner /lava-8794305/1 / # /lava-8794305/bin/lava-test-runner /lava-8794305/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-8794305/1/tests/1_bootrr + cat uuid + UUID=8794305_<8>[ 8.918323] 1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-8794305/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-8794305/1/../bin/lava-test-case <8>[ 9.987575] /lava-8794305/1/../bin/lava-test-case <8>[ 10.026836] /lava-8794305/1/../bin/lava-test-case <8>[ 10.051170] + set +x <8>[ 10.069587] / #