[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 8853796/tftp-deploy-2p5cuv4h/kernel/zImage tftp 0x10000000 8853796/tftp-deploy-2p5cuv4h/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '8853796/tftp-deploy-2p5cuv4h/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 8853796/tftp-deploy-2p5cuv4h/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8853796/tftp-deploy-2p5cuv4h/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '8853796/tftp-deploy-2p5cuv4h/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 2.9 MiB/s done Bytes transferred = 13315826 (cb2ef2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8853796/tftp-deploy-2p5cuv4h/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8853796/tftp-deploy-2p5cuv4h/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '8853796/tftp-deploy-2p5cuv4h/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.3 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13315762 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.271-cip89 (KernelCI@build-j903855-arm-gcc-10-multi-v7-defconfig-8w8rp) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Tue Jan 24 11:59:26 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 16 pages/cpu s36748 r8192 d20596 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939160K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43880K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008094] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.020995] Console: colour dummy device 80x30 <6>[ 0.022879] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.033557] pid_max: default: 32768 minimum: 301 <6>[ 0.038553] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045302] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053137] CPU: Testing write buffer coherency: ok <6>[ 0.057748] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063391] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069634] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077348] rcu: Hierarchical SRCU implementation. <6>[ 0.083909] EFI services will not be available. <6>[ 0.086149] smp: Bringing up secondary CPUs ... <6>[ 0.091399] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091406] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.102744] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.102751] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.113936] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.113942] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124413] smp: Brought up 1 node, 4 CPUs <6>[ 0.128671] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.135175] CPU: All CPU(s) started in SVC mode. <6>[ 0.141134] devtmpfs: initialized <6>[ 0.150533] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.155980] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.165718] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175264] pinctrl core: initialized pinctrl subsystem <6>[ 0.179511] DMI not present or invalid. <6>[ 0.182786] NET: Registered protocol family 16 <6>[ 0.190125] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.196726] cpuidle: using governor menu <6>[ 0.198752] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.213548] vdd1p1: supplied by regulator-dummy <6>[ 0.216014] vdd3p0: supplied by regulator-dummy <6>[ 0.220749] vdd2p5: supplied by regulator-dummy <6>[ 0.225554] vddarm: supplied by regulator-dummy <6>[ 0.230501] vddpu: supplied by regulator-dummy <6>[ 0.234902] vddsoc: supplied by regulator-dummy <6>[ 0.253282] No ATAGs? <6>[ 0.253423] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.261382] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.270798] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.277681] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.289442] Serial: AMBA PL011 UART driver <6>[ 0.293253] console [pstore-1] enabled <6>[ 0.295117] pstore: Registered ramoops as persistent store backend <6>[ 0.301408] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.329316] mxs-dma 110000.dma-apbh: initialized <6>[ 0.338750] vgaarb: loaded <5>[ 0.339654] SCSI subsystem initialized <6>[ 0.343276] usbcore: registered new interface driver usbfs <6>[ 0.348687] usbcore: registered new interface driver hub <6>[ 0.354218] usbcore: registered new device driver usb <6>[ 0.360771] i2c i2c-0: IMX I2C adapter registered <6>[ 0.364451] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.370580] i2c i2c-1: IMX I2C adapter registered <6>[ 0.374974] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.380959] i2c i2c-2: IMX I2C adapter registered <6>[ 0.385501] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.392610] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.396299] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.405697] PTP clock support registered <6>[ 0.410103] EDAC MC: Ver: 3.0.0 <6>[ 0.416001] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.478370] NET: Registered protocol family 2 <6>[ 0.480584] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.488109] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.495046] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.502441] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.509187] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.515843] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.521874] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.528605] NET: Registered protocol family 1 <6>[ 0.533574] RPC: Registered named UNIX socket transport module. <6>[ 0.539239] RPC: Registered udp transport module. <6>[ 0.544170] RPC: Registered tcp transport module. <6>[ 0.549145] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.556347] Trying to unpack rootfs image as initramfs... <6>[ 1.669704] Freeing initrd memory: 13004K <4>[ 1.671578] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.678829] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.688809] Initialise system trusted keyrings <6>[ 1.691854] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.704261] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.708255] NFS: Registering the id_resolver key type <5>[ 1.712842] Key type id_resolver registered <5>[ 1.717276] Key type id_legacy registered <6>[ 1.721547] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.728300] Key type asymmetric registered <5>[ 1.730476] Asymmetric key parser 'x509' registered <6>[ 1.735647] bounce: pool size: 64 pages <6>[ 1.739750] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.747368] io scheduler noop registered <6>[ 1.751528] io scheduler deadline registered <6>[ 1.756193] io scheduler cfq registered (default) <6>[ 1.761011] io scheduler mq-deadline registered <6>[ 1.765796] io scheduler kyber registered <6>[ 1.791387] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.795912] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.803050] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.810351] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.830264] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.833656] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.841508] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.847708] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.855599] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.856026] PU : no governor for states <6>[ 1.865212] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.869295] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.941398] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.948667] SuperH (H)SCI(F) driver initialized <6>[ 1.951505] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.960265] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.971247] console [ttymxc1] enabled <6>[ 1.971247] console [ttymxc1] enabled <6>[ 1.976245] bootconsole [ec_imx21] disabled <6>[ 1.976245] bootconsole [ec_imx21] disabled <6>[ 1.986351] msm_serial: driver initialized <6>[ 1.992551] STMicroelectronics ASC driver initialized <6>[ 1.999710] STM32 USART driver initialized <4>[ 2.014715] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.023411] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.030393] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.037175] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.046215] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.053335] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.067960] brd: module loaded <6>[ 2.080653] loop: module loaded <6>[ 2.087277] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.095470] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.103786] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.112259] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.123041] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.130321] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.139398] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.150212] scsi host0: ahci-imx <6>[ 2.154275] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.173139] CAN device driver interface <6>[ 2.178514] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.185547] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.194510] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.203639] pps pps0: new PPS source ptp0 <6>[ 2.234333] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.241755] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.247883] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.254123] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.261371] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.273015] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.280746] usbcore: registered new interface driver pegasus <6>[ 2.286733] usbcore: registered new interface driver asix <6>[ 2.292431] usbcore: registered new interface driver ax88179_178a <6>[ 2.298849] usbcore: registered new interface driver cdc_ether <6>[ 2.304990] usbcore: registered new interface driver smsc75xx <6>[ 2.311065] usbcore: registered new interface driver smsc95xx <6>[ 2.317127] usbcore: registered new interface driver net1080 <6>[ 2.323082] usbcore: registered new interface driver cdc_subset <6>[ 2.329315] usbcore: registered new interface driver zaurus <6>[ 2.335227] usbcore: registered new interface driver cdc_ncm <6>[ 2.344049] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.350878] ehci-pci: EHCI PCI platform driver <6>[ 2.355632] ehci-platform: EHCI generic platform driver <6>[ 2.361435] ehci-orion: EHCI orion driver <6>[ 2.365937] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.370432] ehci-st: EHCI STMicroelectronics driver <6>[ 2.375756] ehci-exynos: EHCI EXYNOS driver <6>[ 2.380419] ehci-atmel: EHCI Atmel driver <6>[ 2.384877] tegra-ehci: Tegra EHCI driver <6>[ 2.389390] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.395851] ohci-pci: OHCI PCI platform driver <6>[ 2.400621] ohci-platform: OHCI generic platform driver <6>[ 2.406390] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.410850] ohci-st: OHCI STMicroelectronics driver <6>[ 2.416203] ohci-atmel: OHCI Atmel driver <6>[ 2.421457] usbcore: registered new interface driver usb-storage <6>[ 2.430016] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.442079] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.452238] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.457429] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.486030] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.487521] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.492358] hub 1-0:1.0: USB hub found <6>[ 2.497419] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.501440] hub 1-0:1.0: 1 port detected <6>[ 2.507951] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.518320] i2c /dev entries driver <3>[ 2.534441] imx_thermal tempmon: invalid sensor calibration data <3>[ 2.540752] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 2.547927] imx_thermal: probe of tempmon failed with error -22 <6>[ 2.557399] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.568805] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.575252] sdhci: Copyright(c) Pierre Ossman <6>[ 2.582183] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.590450] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.597257] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.602691] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.608209] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.648031] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.656068] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.661580] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.701466] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.712922] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.719998] usbcore: registered new interface driver usbhid <6>[ 2.725839] usbhid: USB HID core driver <6>[ 2.735846] NET: Registered protocol family 10 <6>[ 2.741677] Segment Routing with IPv6 <6>[ 2.745693] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.752460] NET: Registered protocol family 17 <6>[ 2.757215] can: controller area network core (rev 20170425 abi 9) <6>[ 2.763731] NET: Registered protocol family 29 <6>[ 2.768461] can: raw protocol (rev 20170425) <6>[ 2.773001] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.778948] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.785080] Key type dns_resolver registered <6>[ 2.790406] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.796159] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.801894] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.808376] ThumbEE CPU extension supported. <5>[ 2.812923] Registering SWP/SWPB emulation handler <5>[ 2.818698] Loading compiled-in X.509 certificates <6>[ 2.825343] pstore: Using compression: deflate <6>[ 2.848658] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.856096] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.864802] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.873350] mmc0: new high speed SDHC card at address 0001 <6>[ 2.879383] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.888353] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.897069] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.905420] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 2.910197] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.917396] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.925788] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.934853] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.942132] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.950416] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.957956] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.966481] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.974070] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.982918] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.991626] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.998799] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.006900] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.015915] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.023318] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.032273] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.039271] hctosys: unable to open rtc device (rtc0) <6>[ 3.046162] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.053817] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.062487] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 3.070089] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.077771] GPT:29296874 != 30965759 <4>[ 3.081611] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.087894] GPT:29296874 != 30965759 <4>[ 3.091733] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.097197] mmcblk0: p1 p2 p3 <6>[ 3.100763] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.109712] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.118405] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.125632] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.133769] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.142806] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.146636] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 3.151726] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.164705] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 3.172597] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.187025] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.195480] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.203180] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.212007] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.220708] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.227826] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.235876] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.244914] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.252195] hub 1-1:1.0: USB hub found <6>[ 3.256304] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.263634] hub 1-1:1.0: 3 ports detected <6>[ 3.269739] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.277139] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.285528] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.293047] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.301809] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.310501] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.317465] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.325453] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.334484] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.341621] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 5.276678] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 5.306142] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.336096] Sending DHCP requests ., OK <6>[ 5.380230] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 <6>[ 5.388659] IP-Config: Complete: <6>[ 5.392178] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 <6>[ 5.403008] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 5.412009] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 5.412017] nameserver0=192.168.101.1 <6>[ 5.430869] Freeing unused kernel memory: 2048K <6>[ 5.466669] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.632192] udevd[107]: starting version 3.2.9 <5>[ 5.637911] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.644857] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.651716] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.667102] udevd[107]: specified user 'tss' unknown <27>[ 5.672555] udevd[107]: specified group 'tss' unknown <30>[ 5.680633] udevd[108]: starting eudev-3.2.9 <6>[ 6.051876] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.069768] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.077594] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 6.091710] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.100703] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.125065] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.134522] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.143303] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.150993] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.162563] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.169735] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.178831] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.187954] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.188780] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.195239] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.201937] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.210301] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.223862] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.231220] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.237704] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 6.244977] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.252601] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.260512] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 6.262137] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.274438] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.281632] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.290524] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.299791] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.307130] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.315696] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.323148] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.323275] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.360886] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.375272] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.384078] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.394475] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.397387] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.404157] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.409520] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.423271] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.430791] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <4>[ 6.432281] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.447153] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.454384] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.463284] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.470791] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.480201] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.488318] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.498385] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.507220] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.514294] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.523073] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.532179] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.539564] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 6.828353] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 6.931187] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8853796/environment . /lava-8853796/environment / # /lava-8853796/bin/lava-test-runner /lava-8853796/0 /lava-8853796/bin/lava-test-runner /lava-8853796/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-8853796/0/tests/0_dmesg + cat uuid + UUID=8853796_1<8>[ 7.536574] .5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 7.594332] <8>[ 7.635719] <8>[ 7.681654] + set +x <8>[ 7.691478] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-8853796/environment / # . /lava-8853796/environment/lava-8853796/bin/lava-test-runner /lava-8853796/1 / # /lava-8853796/bin/lava-test-runner /lava-8853796/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-8853796/1/tests/1_bootrr + cat uuid + UUID=8853796_<8>[ 8.207360] 1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-8853796/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-8853796/1/../bin/lava-test-case <8>[ 9.288533] /lava-8853796/1/../bin/lava-test-case <8>[ 9.338290] /lava-8853796/1/../bin/lava-test-case <8>[ 9.369329] + set +x <8>[ 9.387943] / #