[Enter `^Ec?' for help] NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.12 NOTICE: BL2: PRR is R-Car M3 ES1.0 NOTICE: BL2: Boot device is HyperFlash(80MHz) NOTICE: BL2: LCM state is CM NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x52 NOTICE: BL2: DDR3200(rev.0.20)[COLD_BOOT]..0 NOTICE: BL2: DRAM Split is OFF NOTICE: BL2: QoS is default setting(rev.0.16) NOTICE: BL2: v1.3(release):a80bbf3 NOTICE: BL2: Built : 22:16:12, Mar 30 2017 NOTICE: BL2: Normal boot NOTICE: BL2: dst=0xe6316190 src=0x8180000 len=512(0x200) NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800) NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000) NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000) NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000) U-Boot 2020.04+dfsg-2co5bv2022dev0b2 (Nov 03 2020 - 09:02:07 +0000) CPU: Renesas Electronics R8A7796 rev 1.0 Model: Renesas M3ULCB board based on r8a7796 DRAM: 1.9 GiB Bank #0: 0x048000000 - 0x07fffffff, 896 MiB Bank #1: 0x600000000 - 0x63fffffff, 1 GiB MMC: sd@ee100000: 0, sd@ee140000: 1 Loading Environment from MMC... OK In: serial@e6e88000 Out: serial@e6e88000 Err: serial@e6e88000 Net: eth0: ethernet@e6800000 Hit any key to stop autoboot: 99  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@e6800000 Waiting for PHY auto negotiation to complete............ done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 DHCP client bound to address 192.168.101.102 (7764 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x68080000 9598142/tftp-deploy-2g1o5emv/kernel/Image tftp 0x68080000 9598142/tftp-deploy-2g1o5emv/kernel/Image Using ethernet@e6800000 device TFTP from server 192.168.101.1; our IP address is 192.168.101.102 Filename '9598142/tftp-deploy-2g1o5emv/kernel/Image'. Load address: 0x68080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 10.4 MiB/s done Bytes transferred = 19307008 (1269a00 hex) => tftp 0x4a000000 9598142/tftp-deploy-2g1o5emv/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4a000000 9598142/tftp-deploy-2g1o5emv/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@e6800000 device TFTP from server 192.168.101.1; our IP address is 192.168.101.102 Filename '9598142/tftp-deploy-2g1o5emv/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4a000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################### 10.3 MiB/s done Bytes transferred = 15177499 (e7971b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x68000000 9598142/tftp-deploy-2g1o5emv/dtb/r8a7796-m3ulcb.dtb tftp 0x68000000 9598142/tftp-deploy-2g1o5emv/dtb/r8a7796-m3ulcb.dtb Using ethernet@e6800000 device TFTP from server 192.168.101.1; our IP address is 192.168.101.102 Filename '9598142/tftp-deploy-2g1o5emv/dtb/r8a7796-m3ulcb.dtb'. Load address: 0x68000000 Loading: *#### 4.6 MiB/s done Bytes transferred = 52637 (cd9d hex) => setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x68080000 0x4a000000 0x68000000 booti 0x68080000 0x4a000000 0x68000000 ## Loading init Ramdisk from Legacy Image at 4a000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15177435 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 68000000 Booting using the fdt blob at 0x68000000 Loading Ramdisk to 57186000, end 57fff6db ... OK Loading Device Tree to 0000000057176000, end 0000000057185d9c ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd073] [ 0.000000] Linux version 4.19.277-cip93 (KernelCI@build-j1172842-arm64-gcc-10-defconfig-kjrwh) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP PREEMPT Tue Mar 14 03:19:11 UTC 2023 [ 0.000000] Machine model: Renesas M3ULCB board based on r8a7796 [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x000000007e000000 [ 0.000000] earlycon: scif0 at MMIO 0x00000000e6e88000 (options '115200n8') [ 0.000000] bootconsole [scif0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000048000000-0x000000063fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x63ffb3a40-0x63ffb51ff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000048000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000063fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000048000000-0x000000007fffffff] [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000063fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 22 pages/cpu s52760 r8192 d29160 u90112 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware [ 0.000000] CPU features: enabling workaround for EL2 vector hardening [ 0.000000] CPU features: enabling workaround for Spectre-BHB [ 0.000000] CPU features: enabling workaround for ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 483840 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] software IO TLB: mapped [mem 0x79fff000-0x7dfff000] (64MB) <6>[ 0.000000] Memory: 1799276K/1966080K available (11196K kernel code, 1382K rwdata, 4964K rodata, 1280K init, 377K bss, 134036K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6. <6>[ 0.000000] Tasks RCU enabled. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns <6>[ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns <6>[ 0.008349] Console: colour dummy device 80x25 <6>[ 0.013082] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333) <6>[ 0.023556] pid_max: default: 32768 minimum: 301 <6>[ 0.028448] Security Framework initialized <6>[ 0.033652] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) <6>[ 0.041475] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) <6>[ 0.048786] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.055727] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.063989] ASID allocator initialised with 32768 entries <6>[ 0.069706] rcu: Hierarchical SRCU implementation. <6>[ 0.075628] Detected Renesas R-Car Gen3 r8a7796 ES1.0 <6>[ 0.081825] EFI services will not be available. <6>[ 0.086837] smp: Bringing up secondary CPUs ... <6>[ 0.091998] Detected PIPT I-cache on CPU1 <6>[ 0.092034] CPU1: Booted secondary processor 0x0000000001 [0x411fd073] <3>[ 0.092338] psci: failed to boot CPU2 (-22) <3>[ 0.107779] CPU2: failed to boot: -22 <3>[ 0.111989] psci: failed to boot CPU3 (-22) <3>[ 0.116425] CPU3: failed to boot: -22 <3>[ 0.120624] psci: failed to boot CPU4 (-22) <3>[ 0.125062] CPU4: failed to boot: -22 <3>[ 0.129241] psci: failed to boot CPU5 (-22) <3>[ 0.133669] CPU5: failed to boot: -22 <6>[ 0.137615] smp: Brought up 1 node, 2 CPUs <6>[ 0.141952] SMP: Total of 2 processors activated. <6>[ 0.146904] CPU features: detected: 32-bit EL0 Support <6>[ 0.152753] CPU: All CPU(s) started at EL1 <6>[ 0.157097] alternatives: patching kernel code <6>[ 0.162571] devtmpfs: initialized <6>[ 0.170057] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.180067] futex hash table entries: 2048 (order: 5, 131072 bytes) <6>[ 0.187201] pinctrl core: initialized pinctrl subsystem <6>[ 0.193987] DMI not present or invalid. <6>[ 0.198471] NET: Registered protocol family 16 <6>[ 0.203333] audit: initializing netlink subsys (disabled) <5>[ 0.209061] audit: type=2000 audit(0.140:1): state=initialized audit_enabled=0 res=1 <6>[ 0.217048] cpuidle: using governor menu <6>[ 0.221371] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.228936] DMA: preallocated 256 KiB pool for atomic allocations <6>[ 0.236329] Serial: AMBA PL011 UART driver <6>[ 0.243053] sh-pfc e6060000.pin-controller: r8a77960_pfc support registered <6>[ 0.274340] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.281669] cryptd: max_cpu_qlen set to 1000 <6>[ 0.286906] ACPI: Interpreter disabled. <6>[ 0.293690] vgaarb: loaded <5>[ 0.297495] SCSI subsystem initialized <6>[ 0.302139] usbcore: registered new interface driver usbfs <6>[ 0.307965] usbcore: registered new interface driver hub <6>[ 0.313539] usbcore: registered new device driver usb <6>[ 0.319748] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 100000 Hz <6>[ 0.327344] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.332549] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.341908] PTP clock support registered <6>[ 0.346186] EDAC MC: Ver: 3.0.0 <6>[ 0.350390] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.357140] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.363576] VFS: Disk quotas dquot_6.6.0 <6>[ 0.367789] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.374996] pnp: PnP ACPI: disabled <6>[ 0.382754] NET: Registered protocol family 2 <6>[ 0.387685] IP idents hash table entries: 32768 (order: 6, 262144 bytes) <6>[ 0.395396] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes) <6>[ 0.403489] TCP established hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.411000] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) <6>[ 0.418007] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.424894] UDP hash table entries: 1024 (order: 3, 32768 bytes) <6>[ 0.431166] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) <6>[ 0.437944] NET: Registered protocol family 1 <6>[ 0.442827] RPC: Registered named UNIX socket transport module. <6>[ 0.449032] RPC: Registered udp transport module. <6>[ 0.453977] RPC: Registered tcp transport module. <6>[ 0.458916] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.465691] Unpacking initramfs... <6>[ 0.953589] Freeing initrd memory: 14820K <6>[ 0.958148] hw perfevents: /pmu_a53: failed to probe PMU! <6>[ 0.963803] hw perfevents: /pmu_a53: failed to register PMU devices! <6>[ 0.970544] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available <6>[ 0.979228] kvm [1]: HYP mode not available <5>[ 0.985934] Initialise system trusted keyrings <6>[ 0.990843] workingset: timestamp_bits=44 max_order=19 bucket_order=0 <6>[ 1.001001] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.007639] NFS: Registering the id_resolver key type <5>[ 1.012955] Key type id_resolver registered <5>[ 1.017402] Key type id_legacy registered <6>[ 1.021665] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.028608] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.036368] 9p: Installing v9fs 9p2000 file system support <5>[ 1.043851] Key type asymmetric registered <5>[ 1.048249] Asymmetric key parser 'x509' registered <6>[ 1.053420] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) <6>[ 1.061053] io scheduler noop registered <6>[ 1.065221] io scheduler deadline registered <6>[ 1.069849] io scheduler cfq registered (default) <6>[ 1.074797] io scheduler mq-deadline registered <6>[ 1.079568] io scheduler kyber registered <6>[ 1.089623] gpio_rcar e6050000.gpio: driving 16 GPIOs <6>[ 1.095154] gpio_rcar e6051000.gpio: driving 29 GPIOs <6>[ 1.100658] gpio_rcar e6052000.gpio: driving 15 GPIOs <6>[ 1.106580] gpio_rcar e6053000.gpio: driving 16 GPIOs <6>[ 1.112049] gpio_rcar e6054000.gpio: driving 18 GPIOs <6>[ 1.117507] gpio_rcar e6055000.gpio: driving 26 GPIOs <6>[ 1.122958] gpio_rcar e6055400.gpio: driving 32 GPIOs <6>[ 1.128441] gpio_rcar e6055800.gpio: driving 4 GPIOs <4>[ 1.136072] EINJ: ACPI disabled. <6>[ 1.147085] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.156075] SuperH (H)SCI(F) driver initialized <6>[ 1.161486] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 112, base_baud = 0) is a scif <6>[ 1.170129] console [ttySC0] enabled <6>[ 1.170129] console [ttySC0] enabled <6>[ 1.177802] bootconsole [scif0] disabled <6>[ 1.177802] bootconsole [scif0] disabled <6>[ 1.186804] msm_serial: driver initialized <6>[ 1.197105] loop: module loaded <6>[ 1.204244] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.210351] thunder_xcv, ver 1.0 <6>[ 1.213880] thunder_bgx, ver 1.0 <6>[ 1.217396] nicpf, ver 1.0 <6>[ 1.220734] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.226828] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.233044] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.240268] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.246129] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k <6>[ 1.254219] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.260706] sky2: driver version 1.30 <6>[ 1.265562] VFIO - User Level meta-driver version: 0.3 <6>[ 1.271958] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.278753] ehci-pci: EHCI PCI platform driver <6>[ 1.283486] ehci-platform: EHCI generic platform driver <6>[ 1.289248] ehci-platform ee0a0100.usb: EHCI Host Controller <6>[ 1.295188] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1 <6>[ 1.303603] ehci-platform ee0a0100.usb: irq 147, io mem 0xee0a0100 <6>[ 1.325151] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10 <6>[ 1.331960] hub 1-0:1.0: USB hub found <6>[ 1.335987] hub 1-0:1.0: 1 port detected <6>[ 1.340433] ehci-orion: EHCI orion driver <6>[ 1.344877] ehci-exynos: EHCI EXYNOS driver <6>[ 1.349410] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.355864] ohci-pci: OHCI PCI platform driver <6>[ 1.360618] ohci-platform: OHCI generic platform driver <6>[ 1.366273] ohci-platform ee0a0000.usb: Generic Platform OHCI controller <6>[ 1.373253] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2 <6>[ 1.381445] ohci-platform ee0a0000.usb: irq 147, io mem 0xee0a0000 <6>[ 1.475552] hub 2-0:1.0: USB hub found <6>[ 1.479582] hub 2-0:1.0: 1 port detected <6>[ 1.484012] ohci-exynos: OHCI EXYNOS driver <6>[ 1.488962] usbcore: registered new interface driver usb-storage <6>[ 1.497389] i2c /dev entries driver <6>[ 1.508875] cs2000-cp 2-004f: revision - C1 <6>[ 1.513383] i2c-rcar e6510000.i2c: probed <6>[ 1.523504] i2c-rcar e66d8000.i2c: probed <6>[ 1.533329] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 2 trip points <6>[ 1.544603] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 2 trip points <6>[ 1.555238] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 2 trip points <4>[ 1.564796] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 1499999 KHz <4>[ 1.572551] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1500000 KHz <6>[ 1.582097] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.588591] sdhci: Copyright(c) Pierre Ossman <6>[ 1.593952] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO <6>[ 1.600691] renesas_sdhi_internal_dmac ee140000.sd: Linked as a consumer to regulator.2 <6>[ 1.609000] renesas_sdhi_internal_dmac ee140000.sd: Linked as a consumer to regulator.1 <6>[ 1.665691] renesas_sdhi_internal_dmac ee140000.sd: mmc0 base at 0xee140000 max clock rate 200 MHz <6>[ 1.675061] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.682156] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.689297] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.696300] usbcore: registered new interface driver usbhid <6>[ 1.702194] usbhid: USB HID core driver <6>[ 1.708742] NET: Registered protocol family 17 <6>[ 1.713600] 9pnet: Installing 9P2000 support <5>[ 1.718194] Key type dns_resolver registered <6>[ 1.723306] registered taskstats version 1 <5>[ 1.727886] Loading compiled-in X.509 certificates <6>[ 1.739279] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs <6>[ 1.751101] bd9571mwv 7-0030: Device: BD9571MWV rev. 1 <6>[ 1.765337] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO <6>[ 1.771651] renesas_sdhi_internal_dmac ee100000.sd: Linked as a consumer to regulator.3 <6>[ 1.779948] renesas_sdhi_internal_dmac ee100000.sd: Linked as a consumer to regulator.4 <6>[ 1.826648] mmc0: new HS200 MMC card at address 0001 <6>[ 1.832257] mmcblk0: mmc0:0001 R1J55A 7.28 GiB <6>[ 1.836598] renesas_sdhi_internal_dmac ee100000.sd: mmc1 base at 0xee100000 max clock rate 200 MHz <6>[ 1.837273] mmcblk0boot0: mmc0:0001 R1J55A partition 1 8.00 MiB <4>[ 1.849860] rcar-dmac e6700000.dma-controller: ignoring dependency for device, assuming no driver <6>[ 1.852659] mmcblk0boot1: mmc0:0001 R1J55A partition 2 8.00 MiB <4>[ 1.864179] rcar-dmac e7300000.dma-controller: ignoring dependency for device, assuming no driver <6>[ 1.867923] mmcblk0rpmb: mmc0:0001 R1J55A partition 3 4.00 MiB, chardev (239:0) <4>[ 1.880287] rcar-dmac e7310000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.896284] rcar-dmac ec700000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.907204] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 1.913541] rcar-dmac ec720000.dma-controller: ignoring dependency for device, assuming no driver <4>[ 1.915946] GPT:7812499 != 15269887 <4>[ 1.927291] ravb e6800000.ethernet: ignoring dependency for device, assuming no driver <4>[ 1.928742] GPT:Alternate GPT header not at the end of the disk. <4>[ 1.942286] GPT:7812499 != 15269887 <4>[ 1.946041] GPT: Use GNU Parted to correct GPT errors. <6>[ 1.951503] mmcblk0: p1 p2 p3 <6>[ 1.961235] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:0a:01:9a:9c, IRQ 109. <6>[ 1.971298] input: keyboard as /devices/platform/keyboard/input/input0 <6>[ 1.978491] hctosys: unable to open rtc device (rtc0) <6>[ 2.026290] mmc1: new ultra high speed SDR50 SDHC card at address 0001 <6>[ 2.033539] mmcblk1: mmc1:0001 SD 14.6 GiB <6>[ 2.062333] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=164) <4>[ 2.077205] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.085982] GPT:7812499 != 30560255 <4>[ 2.089733] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.095997] GPT:7812499 != 30560255 <4>[ 2.099746] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.105157] mmcblk1: p1 p2 p3 <6>[ 12.085142] Waiting up to 110 more seconds for network. <6>[ 12.969269] ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx <5>[ 12.997147] Sending DHCP requests .., OK <6>[ 15.729348] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.102 <6>[ 15.737699] IP-Config: Complete: <6>[ 15.741191] device=eth0, hwaddr=2e:09:0a:01:9a:9c, ipaddr=192.168.101.102, mask=255.255.255.0, gw=192.168.101.1 <6>[ 15.751972] host=r8a7796-m3ulcb-cbg-0, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 15.760841] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 15.760843] nameserver0=192.168.101.1 <6>[ 15.773051] ALSA device list: <6>[ 15.776310] No soundcards found. <6>[ 15.780952] Freeing unused kernel memory: 1280K <6>[ 15.785811] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 15.837383] udevd[1737]: starting version 3.2.9 <5>[ 15.842718] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 15.849619] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 15.856370] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 15.865902] udevd[1737]: specified user 'tss' unknown <27>[ 15.871417] udevd[1737]: specified group 'tss' unknown <30>[ 15.877974] udevd[1738]: starting eudev-3.2.9 <6>[ 16.058383] rcar_sound ec500000.sound: probed <6>[ 16.070401] media: Linux media interface: v0.10 <4>[ 16.081407] rcar-fcp fe9af000.fcp: ignoring dependency for device, assuming no driver <6>[ 16.099030] videodev: Linux video capture interface: v2.00 <4>[ 16.101416] rcar-fcp fea27000.fcp: ignoring dependency for device, assuming no driver <4>[ 16.113957] rcar-fcp fea2f000.fcp: ignoring dependency for device, assuming no driver <4>[ 16.123867] rcar-fcp fea37000.fcp: ignoring dependency for device, assuming no driver <6>[ 16.156886] rcar_fdp1 fe940000.fdp1: Device registered as /dev/video5 <6>[ 16.205226] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok <6>[ 16.222036] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.231437] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY) <4>[ 16.241499] asoc-simple-card sound: ASoC: no DMI vendor name! <6>[ 16.248121] [drm] No driver support for vblank timestamp query. <6>[ 16.255987] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver <6>[ 16.265689] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.273434] [drm] No driver support for vblank timestamp query. <6>[ 16.285729] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.292798] [drm] No driver support for vblank timestamp query. <6>[ 16.443067] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.455125] [drm] No driver support for vblank timestamp query. <6>[ 16.466046] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.476676] [drm] No driver support for vblank timestamp query. <6>[ 16.484763] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 16.491662] [drm] No driver support for vblank timestamp query. done Saving random seed: <5>[ 17.762282] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 17.798691] random: dropbear: uninitialized urandom read (32 bytes read) <6>[ 17.825856] NET: Registered protocol family 10 <6>[ 17.831367] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9598142/environment . /lava-9598142/environment / # /lava-9598142/bin/lava-test-runner /lava-9598142/0 /lava-9598142/bin/lava-test-runner /lava-9598142/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava<8>[ 18.384812] -9598142/0/tests/0_dmesg + cat uuid + UUID=9598142_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.405581] <8>[ 18.425627] <8>[ 18.445735] + set +x <8>[ 18.455096] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9598142/environment / # . /lava-9598142/environment/lava-9598142/bin/lava-test-runner /lava-9598142/1 / # /lava-9598142/bin/lava-test-runner /lava-9598142/1 + export 'TESTRUN_ID=1_bootrr' + cd /lav<8>[ 18.920213] a-9598142/1/tests/1_bootrr + cat uuid + UUID=9598142_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9598142/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto feb00000.display /lava-9598142/1/../bin/lava-test-case <8>[ 19.946555] /lava-9598142/1/../bin/lava-test-case <8>[ 20.967983] /lava-9598142/1/../bin/lava-test-case <8>[ 20.982005] + set +x <8>[ 20.993981] / #