[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (2 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 8893640/tftp-deploy-86m45ypl/kernel/zImage tftp 0x10000000 8893640/tftp-deploy-86m45ypl/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '8893640/tftp-deploy-86m45ypl/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 12.4 MiB/s done Bytes transferred = 9691648 (93e200 hex) => tftp 0x14000000 8893640/tftp-deploy-86m45ypl/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8893640/tftp-deploy-86m45ypl/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '8893640/tftp-deploy-86m45ypl/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.4 MiB/s done Bytes transferred = 12141675 (b9446b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8893640/tftp-deploy-86m45ypl/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8893640/tftp-deploy-86m45ypl/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '8893640/tftp-deploy-86m45ypl/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.9 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8893640/extract-nfsrootfs-jj5p_3hh,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8893640/extract-nfsrootfs-jj5p_3hh,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93e200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12141611 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.162-cip24-rt10 (KernelCI@build-j927046-arm-gcc-10-multi-v7-defconfig-nm469) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Jan 27 00:05:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/8893640/extract-nfsrootfs-jj5p_3hh,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 937508K/1048576K available (13312K kernel code, 2324K rwdata, 5348K rodata, 2048K init, 417K bss, 45532K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000017] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004141] Console: colour dummy device 80x30 [ 0.004192] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004205] pid_max: default: 32768 minimum: 301 [ 0.004369] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004393] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005022] CPU: Testing write buffer coherency: ok [ 0.005054] CPU0: Spectre v2: using BPIALL workaround [ 0.005299] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005994] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007673] rcu: Hierarchical SRCU implementation. [ 0.011501] EFI services will not be available. [ 0.011805] smp: Bringing up secondary CPUs ... [ 0.012597] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012612] CPU1: Spectre v2: using BPIALL workaround [ 0.013503] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013516] CPU2: Spectre v2: using BPIALL workaround [ 0.014387] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014399] CPU3: Spectre v2: using BPIALL workaround [ 0.014510] smp: Brought up 1 node, 4 CPUs [ 0.014520] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014529] CPU: All CPU(s) started in SVC mode. [ 0.015080] devtmpfs: initialized [ 0.022477] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022703] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022725] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025828] pinctrl core: initialized pinctrl subsystem [ 0.027675] DMI not present or invalid. [ 0.028505] NET: Registered protocol family 16 [ 0.032044] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034371] thermal_sys: Registered thermal governor 'step_wise' [ 0.034551] cpuidle: using governor menu [ 0.034723] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.207007] vdd1p1: supplied by regulator-dummy [ 0.214176] vdd3p0: supplied by regulator-dummy [ 0.221214] vdd2p5: supplied by regulator-dummy [ 0.228300] vddarm: supplied by regulator-dummy [ 0.235546] vddpu: supplied by regulator-dummy [ 0.242473] vddsoc: supplied by regulator-dummy [ 0.566198] No ATAGs? [ 0.566343] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.566353] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.570594] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.576786] Serial: AMBA PL011 UART driver [ 0.579064] printk: console [ramoops-1] enabled [ 0.579274] pstore: Registered ramoops as persistent store backend [ 0.579281] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.611881] iommu: Default domain type: Translated [ 0.612309] vgaarb: loaded [ 0.613231] SCSI subsystem initialized [ 0.613789] usbcore: registered new interface driver usbfs [ 0.613844] usbcore: registered new interface driver hub [ 0.613885] usbcore: registered new device driver usb [ 0.615433] i2c i2c-0: IMX I2C adapter registered [ 0.616782] i2c i2c-1: IMX I2C adapter registered [ 0.617594] i2c i2c-2: IMX I2C adapter registered [ 0.619012] pps_core: LinuxPPS API ver. 1 registered [ 0.619018] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.619091] PTP clock support registered [ 0.622978] clocksource: Switched to clocksource mxc_timer1 [ 1.669632] NET: Registered protocol family 2 [ 1.670071] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.671194] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.671237] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.671320] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.671463] TCP: Hash tables configured (established 8192 bind 8192) [ 1.671681] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.671725] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.671902] NET: Registered protocol family 1 [ 1.672507] RPC: Registered named UNIX socket transport module. [ 1.672516] RPC: Registered udp transport module. [ 1.672520] RPC: Registered tcp transport module. [ 1.672523] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.672533] PCI: CLS 0 bytes, default 64 [ 1.673030] Trying to unpack rootfs image as initramfs... [ 2.632209] Freeing initrd memory: 11860K [ 2.632689] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.633201] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.635060] Initialise system trusted keyrings [ 2.635413] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.641114] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.641836] NFS: Registering the id_resolver key type [ 2.641889] Key type id_resolver registered [ 2.641895] Key type id_legacy registered [ 2.641984] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.641992] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.642022] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.642489] Key type asymmetric registered [ 2.642497] Asymmetric key parser 'x509' registered [ 2.642549] bounce: pool size: 64 pages [ 2.642588] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.642595] io scheduler mq-deadline registered [ 2.642600] io scheduler kyber registered [ 2.683890] mxs-dma 110000.dma-apbh: initialized [ 2.688772] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.688790] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.750551] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.755243] SuperH (H)SCI(F) driver initialized [ 2.756265] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.757285] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 2.757326] printk: console [ttymxc1] enabled [ 2.758831] msm_serial: driver initialized [ 2.759098] STMicroelectronics ASC driver initialized [ 2.761098] STM32 USART driver initialized [ 2.773007] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.773166] panel-simple panel-lcd: Specify missing connector_type [ 2.773553] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.782374] brd: module loaded [ 2.792247] loop: module loaded [ 2.796329] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.796344] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.796354] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.796362] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.796441] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.796601] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.796669] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.799528] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.799557] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.799574] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.801066] scsi host0: ahci-imx [ 2.801443] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 2.814209] CAN device driver interface [ 2.815618] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.819191] pps pps0: new PPS source ptp0 [ 2.838093] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.839662] e1000e: Intel(R) PRO/1000 Network Driver [ 2.839668] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.839727] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.839732] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.846204] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.846252] usbcore: registered new interface driver pegasus [ 2.846292] usbcore: registered new interface driver asix [ 2.846327] usbcore: registered new interface driver ax88179_178a [ 2.846360] usbcore: registered new interface driver cdc_ether [ 2.846401] usbcore: registered new interface driver smsc75xx [ 2.846449] usbcore: registered new interface driver smsc95xx [ 2.846485] usbcore: registered new interface driver net1080 [ 2.846519] usbcore: registered new interface driver cdc_subset [ 2.846548] usbcore: registered new interface driver zaurus [ 2.846620] usbcore: registered new interface driver cdc_ncm [ 2.850382] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.850389] ehci-pci: EHCI PCI platform driver [ 2.850424] ehci-platform: EHCI generic platform driver [ 2.850731] ehci-orion: EHCI orion driver [ 2.850962] SPEAr-ehci: EHCI SPEAr driver [ 2.851153] ehci-st: EHCI STMicroelectronics driver [ 2.851338] ehci-exynos: EHCI Exynos driver [ 2.851526] ehci-atmel: EHCI Atmel driver [ 2.851705] tegra-ehci: Tegra EHCI driver [ 2.851924] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.851944] ohci-pci: OHCI PCI platform driver [ 2.851996] ohci-platform: OHCI generic platform driver [ 2.852278] SPEAr-ohci: OHCI SPEAr driver [ 2.852474] ohci-st: OHCI STMicroelectronics driver [ 2.852663] ohci-atmel: OHCI Atmel driver [ 2.853862] usbcore: registered new interface driver usb-storage [ 2.862248] i2c /dev entries driver [ 2.882406] sdhci: Secure Digital Host Controller Interface driver [ 2.882413] sdhci: Copyright(c) Pierre Ossman [ 2.885338] Synopsys Designware Multimedia Card Interface Driver [ 2.887370] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.888695] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 2.888743] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 2.889983] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 2.892734] ledtrig-cpu: registered to indicate activity on CPUs [ 2.893771] usbcore: registered new interface driver usbhid [ 2.893778] usbhid: USB HID core driver [ 2.900496] NET: Registered protocol family 10 [ 2.901592] Segment Routing with IPv6 [ 2.901671] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.902228] NET: Registered protocol family 17 [ 2.902244] can: controller area network core [ 2.902317] NET: Registered protocol family 29 [ 2.902324] can: raw protocol [ 2.902330] can: broadcast manager protocol [ 2.902340] can: netlink gateway - max_hops=1 [ 2.902723] Key type dns_resolver registered [ 2.904810] ThumbEE CPU extension supported. [ 2.904824] Registering SWP/SWPB emulation handler [ 2.905618] printk: console [ttymxc1]: printing thread started [ 2.905879] printk: console [ramoops-1]: printing thread started [ 2.905903] Loading compiled-in X.509 certificates [ 2.910951] pstore: Using crash dump compression: deflate [ 2.932537] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.932678] panel-simple panel-lcd: Specify missing connector_type [ 2.934325] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.939646] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 2.939841] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 2.943392] imx_usb 2184200.usb: No over current polarity defined [ 2.946919] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.946943] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.982876] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.983485] hub 1-0:1.0: USB hub found [ 2.983519] hub 1-0:1.0: 1 port detected [ 2.985620] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 2.990001] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.990125] panel-simple panel-lcd: Specify missing connector_type [ 2.991541] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.996134] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.996263] panel-simple panel-lcd: Specify missing connector_type [ 2.997771] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.999749] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.005484] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.005611] panel-simple panel-lcd: Specify missing connector_type [ 3.007105] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.126784] mmc2: new high speed SDHC card at address 0001 [ 3.127538] mmcblk2: mmc2:0001 SD 14.6 GiB [ 3.139393] ata1: SATA link down (SStatus 0 SControl 300) [ 3.139452] ahci-imx 2200000.sata: no device found, disabling link. [ 3.139459] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.155315] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.251936] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.251942] GPT:29296874 != 30560255 [ 3.251947] GPT:Alternate GPT header not at the end of the disk. [ 3.251949] GPT:29296874 != 30560255 [ 3.251953] GPT: Use GNU Parted to correct GPT errors. [ 3.251990] mmcblk2: p1 p2 p3 [ 3.257342] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.257470] panel-simple panel-lcd: Specify missing connector_type [ 3.258937] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.262872] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.479265] hub 1-1:1.0: USB hub found [ 3.484164] hub 1-1:1.0: 3 ports detected [ 3.527246] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.527364] panel-simple panel-lcd: Specify missing connector_type [ 3.528770] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.313365] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.332927] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.362928] Sending DHCP requests ., OK [ 6.402949] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 [ 6.402973] IP-Config: Complete: [ 6.402979] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 [ 6.403004] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) [ 6.403016] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.403029] nameserver0=192.168.201.1 [ 6.411395] Freeing unused kernel memory: 2048K [ 6.454385] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.272218] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.296800] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.312605] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.312784] panel-simple panel-lcd: Specify missing connector_type [ 7.314824] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.341242] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.341523] panel-simple panel-lcd: Specify missing connector_type [ 7.343953] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.361915] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.362093] panel-simple panel-lcd: Specify missing connector_type [ 7.363671] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.364670] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.379207] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.379663] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.379761] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.380091] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.380162] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.380175] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.380598] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.386274] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.386432] panel-simple panel-lcd: Specify missing connector_type [ 7.388082] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.439685] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.439800] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.439923] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.440023] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.445872] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.446029] panel-simple panel-lcd: Specify missing connector_type [ 7.447696] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.460893] caam 2100000.crypto: Entropy delay = 3200 [ 7.479478] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.479542] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.479600] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.479647] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.521693] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.551843] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 7.552007] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 7.552158] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 7.560213] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 7.565474] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.565632] panel-simple panel-lcd: Specify missing connector_type [ 7.567575] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.582454] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.582472] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.582481] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.620714] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.620886] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.620946] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.620999] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.621061] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.625292] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.627123] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.627280] panel-simple panel-lcd: Specify missing connector_type [ 7.628862] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.632734] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.632852] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.632924] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.632972] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.681251] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.681431] panel-simple panel-lcd: Specify missing connector_type [ 7.683261] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.693996] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.694096] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.694191] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.694269] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.108046] caam algorithms registered in /proc/crypto [ 8.109463] caam 2100000.crypto: registering rng-caam [ 8.115167] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.115497] panel-simple panel-lcd: Specify missing connector_type [ 8.119014] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.124233] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.124336] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers [ 8.124406] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) ... [ 8.124459] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 8.291881] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.161448] systemd[1]: System time before build time, advancing clock. [ 9.220972] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.221719] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.295873] systemd[1]: Set hostname to . [ 10.169886] systemd[1]: Queued start job for default target Graphical Interface. [ 10.171905] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.171929] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ OK ] Created slice[ 10.172643] systemd[1]: Created slice system-getty.slice. system-getty.slice. [ OK ] Created slice system-modprobe.slice. [ 10.233667] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.274238] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 10.304006] systemd[1]: Created slice User and Session Slice. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 10.333805] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.363285] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ 10.393680] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.393940] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ 10.423422] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. [ 10.453390] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. [ 10.483283] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. [ 10.513440] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.544237] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on [ 10.610116] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. Journal Socket (/dev/log[ 10.611973] systemd[1]: Listening on Journal Socket (/dev/log). ). [ OK ] Listening on Journal Socket. [ 10.653824] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.695503] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ 10.726465] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ 10.753692] systemd[1]: Listening on udev Kernel Socket. [ 10.784164] systemd[1]: Condition check resulted in Huge Pages File System being skipped. Mounting Kernel[ 10.785134] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. Debug File System... [ 10.790960] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Trace File System... [ 10.846769] systemd[1]: Mounting Kernel Trace File System... Starting Create list of st…odes for the curr[ 10.877554] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel... Starting Load K[ 10.919478] systemd[1]: Starting Load Kernel Module configfs... ernel Module configfs... Starting Load Kernel Module drm... [ 10.966701] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... [ 10.996696] systemd[1]: Starting Load Kernel Module fuse... Starting Journa[ 11.027634] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... [ 11.031355] systemd[1]: Starting Journal Service... [ 11.082374] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... [ 11.116666] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Coldplug All udev Devices... [ 11.146788] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0[ 11.177787] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. [ 11.213816] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.244109] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished [0;[ 11.281191] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.281830] systemd[1]: Finished Load Kernel Module configfs. 1;39mLoad Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ 11.324299] systemd[1]: modprobe@drm.service: Succeeded. [ 11.324945] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ 11.354218] systemd[1]: modprobe@fuse.service: Succeeded. [ 11.354876] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ 11.384116] systemd[1]: Finished Load Kernel Modules. [ OK ] Started Journal Service. [ 11.413523] systemd[1]: Started Journal Service. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ 11.580612] systemd-journald[282]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.162-cip24-rt10 #1 SMP Fri Jan 27 00:05:23 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8893640/extract-nfsrootfs-jj5p_3hh' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8893640/extract-nfsrootfs-jj5p_3hh' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8893640/environment . /lava-8893640/environment / # /lava-8893640/bin/lava-test-runner /lava-8893640/0 /lava-8893640/bin/lava-test-runner /lava-8893640/0 + export TESTRUN_ID=0_dmesg + cd /lava-8893640/0/tests/0_dmesg + cat uuid + UUID=8893640_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /[ 25.558746] bin/sh /opt/kernelci/dmesg.sh [ 25.667280] [ 25.762764] + set +x / # [ 25.844922] [ 25.845854] # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-8893640/environment / # . /lava-8893640/environment/lava-8893640/bin/lava-test-runner /lava-8893640/1 / # /lava-8893640/bin/lava-test-runner /lava-8893640/1 + export TESTRUN_ID=1_bootrr + cd /lava-8893640/1/tests/1_bootrr + cat uuid + UUID=8893640_1.6.2.4.5 + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-8893640/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin[ 26.472919] :/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 120000.hdmi backlight-lcd /lava-8893640/1/../bin/lava-test-case [ 27.624013] /lava-8893640/1/../bin/lava-test-case [ 27.718157] /lava-8893640/1/../bin/lava-test-case [ 27.763366] + set +x / # [ 27.795838]