Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3023 device /dev/ttyimx6ul-14x14-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 30C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.160 (1333 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1181717/tftp-deploy-sttl85zu/kernel/zImage tftp 0x80800000 1181717/tftp-deploy-sttl85zu/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181717/tftp-deploy-sttl85zu/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.5 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x86800000 1181717/tftp-deploy-sttl85zu/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1181717/tftp-deploy-sttl85zu/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181717/tftp-deploy-sttl85zu/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5 MiB/s done Bytes transferred = 16078641 (f55731 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1181717/tftp-deploy-sttl85zu/dtb/imx6ul-14x14-evk.dtb tftp 0x83000000 1181717/tftp-deploy-sttl85zu/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181717/tftp-deploy-sttl85zu/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *### 3.3 MiB/s done Bytes transferred = 30855 (7887 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16078577 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300a886 ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29-rt12 (KernelCI@build-j1227176-arm-gcc-10-multi-v7-defconfig-cvvrm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 12:31:55 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131072 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 412952K/524288K available (14336K kernel code, 2330K rwdata, 5348K rodata, 2048K init, 415K bss, 45800K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008090] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.025068] Console: colour dummy device 80x30 <6>[ 0.027046] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.037658] pid_max: default: 32768 minimum: 301 <6>[ 0.042784] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.050074] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.059523] CPU: Testing write buffer coherency: ok <6>[ 0.063783] CPU0: update cpu_capacity 1024 <6>[ 0.067505] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.075228] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.082618] rcu: Hierarchical SRCU implementation. <6>[ 0.090964] EFI services will not be available. <6>[ 0.093366] smp: Bringing up secondary CPUs ... <6>[ 0.097806] smp: Brought up 1 node, 1 CPU <6>[ 0.101989] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.108463] CPU: All CPU(s) started in SVC mode. <6>[ 0.114339] devtmpfs: initialized <6>[ 0.130769] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.136393] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.146131] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.157836] pinctrl core: initialized pinctrl subsystem <6>[ 0.164252] DMI not present or invalid. <6>[ 0.167685] NET: Registered protocol family 16 <6>[ 0.174992] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.184882] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.185078] cpuidle: using governor menu <6>[ 0.438847] vdd3p0: supplied by regulator-dummy <6>[ 0.453901] cpu: supplied by regulator-dummy <6>[ 0.469227] vddsoc: supplied by regulator-dummy <6>[ 0.904964] No ATAGs? <6>[ 0.906077] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.913028] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.927749] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.942205] Serial: AMBA PL011 UART driver <6>[ 1.015727] iommu: Default domain type: Translated <6>[ 1.018921] vgaarb: loaded <5>[ 1.023175] SCSI subsystem initialized <7>[ 1.025802] libata version 3.00 loaded. <6>[ 1.029800] usbcore: registered new interface driver usbfs <6>[ 1.034965] usbcore: registered new interface driver hub <6>[ 1.040620] usbcore: registered new device driver usb <6>[ 1.049149] i2c i2c-0: IMX I2C adapter registered <6>[ 1.053412] i2c i2c-1: IMX I2C adapter registered <6>[ 1.059081] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.061587] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.070935] PTP clock support registered <6>[ 1.083473] clocksource: Switched to clocksource mxc_timer1 <6>[ 3.328211] NET: Registered protocol family 2 <6>[ 3.330502] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 3.339426] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 3.346250] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 3.354244] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 3.361643] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 3.368371] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.375008] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.382531] NET: Registered protocol family 1 <6>[ 3.388619] RPC: Registered named UNIX socket transport module. <6>[ 3.392914] RPC: Registered udp transport module. <6>[ 3.398005] RPC: Registered tcp transport module. <6>[ 3.402832] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 3.409588] PCI: CLS 0 bytes, default 64 <6>[ 3.414818] Trying to unpack rootfs image as initramfs... <6>[ 6.411132] Freeing initrd memory: 15704K <6>[ 6.414076] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 6.424740] Initialise system trusted keyrings <6>[ 6.427445] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 6.449469] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.454820] NFS: Registering the id_resolver key type <5>[ 6.458226] Key type id_resolver registered <5>[ 6.462493] Key type id_legacy registered <6>[ 6.467162] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.473780] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.481457] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.487279] Key type asymmetric registered <5>[ 6.490337] Asymmetric key parser 'x509' registered <6>[ 6.495657] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.503127] io scheduler mq-deadline registered <6>[ 6.507966] io scheduler kyber registered <4>[ 6.564825] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 6.598900] mxs-dma 1804000.dma-apbh: initialized <4>[ 6.630032] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.637175] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 6.769448] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.783386] SuperH (H)SCI(F) driver in������镑5 <6>[ 6.787741] printk: console [ttymxc0] enabled <6>[ 6.790217] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.787741] printk: console [ttymxc0] enabled <6>[ 6.790217] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.798167] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 73, base_baud = 5000000) is a IMX <6>[ 6.801360] msm_serial: driver initialized <6>[ 6.801974] STMicroelectronics ASC driver initialized <6>[ 6.806093] STM32 USART driver initialized <4>[ 6.828440] panel-simple panel: supply power not found, using dummy regulator <4>[ 6.828863] panel-simple panel: Specify missing connector_type <6>[ 6.854297] brd: module loaded <6>[ 6.871895] loop: module loaded <6>[ 6.907540] CAN device driver interface <6>[ 6.910285] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.913690] pps pps0: new PPS source ptp0 <6>[ 7.058010] fec 20b4000.ethernet eth0: registered PHC device 0 <6>[ 7.061388] pps pps1: new PPS source ptp1 <6>[ 9.281469] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 9.284666] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 9.284687] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 9.284846] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 9.284861] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 9.298008] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 9.298148] usbcore: registered new interface driver pegasus <6>[ 9.298268] usbcore: registered new interface driver asix <6>[ 9.298364] usbcore: registered new interface driver ax88179_178a <6>[ 9.298497] usbcore: registered new interface driver cdc_ether <6>[ 9.298632] usbcore: registered new interface driver smsc75xx <6>[ 9.298747] usbcore: registered new interface driver smsc95xx <6>[ 9.298840] usbcore: registered new interface driver net1080 <6>[ 9.298930] usbcore: registered new interface driver cdc_subset <6>[ 9.299014] usbcore: registered new interface driver zaurus <6>[ 9.299221] usbcore: registered new interface driver cdc_ncm <6>[ 9.307086] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 9.307113] ehci-pci: EHCI PCI platform driver <6>[ 9.307217] ehci-platform: EHCI generic platform driver <6>[ 9.307876] ehci-orion: EHCI orion driver <6>[ 9.308345] SPEAr-ehci: EHCI SPEAr driver <6>[ 9.308736] ehci-st: EHCI STMicroelectronics driver <6>[ 9.309120] ehci-exynos: EHCI Exynos driver <6>[ 9.309503] ehci-atmel: EHCI Atmel driver <6>[ 9.309903] tegra-ehci: Tegra EHCI driver <6>[ 9.310368] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 9.310431] ohci-pci: OHCI PCI platform driver <6>[ 9.310572] ohci-platform: OHCI generic platform driver <6>[ 9.311189] SPEAr-ohci: OHCI SPEAr driver <6>[ 9.311607] ohci-st: OHCI STMicroelectronics driver <6>[ 9.312032] ohci-atmel: OHCI Atmel driver <6>[ 9.314667] usbcore: registered new interface driver usb-storage <6>[ 9.332878] i2c /dev entries driver <6>[ 9.380157] sdhci: Secure Digital Host Controller Interface driver <6>[ 9.380179] sdhci: Copyright(c) Pierre Ossman <6>[ 9.386468] Synopsys Designware Multimedia Card Interface Driver <6>[ 9.390847] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 9.403842] sdhci-esdhc-imx 2190000.mmc: Got CD GPIO <6>[ 9.409960] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 9.412426] usbcore: registered new interface driver usbhid <6>[ 9.412450] usbhid: USB HID core driver <6>[ 9.428608] NET: Registered protocol family 10 <6>[ 9.431516] Segment Routing with IPv6 <6>[ 9.431718] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 9.433167] NET: Registered protocol family 17 <6>[ 9.433221] can: controller area network core <6>[ 9.433529] NET: Registered protocol family 29 <6>[ 9.433560] can: raw protocol <6>[ 9.433581] can: broadcast manager protocol <6>[ 9.433610] can: netlink gateway - max_hops=1 <5>[ 9.434720] Key type dns_resolver registered <6>[ 9.438848] ThumbEE CPU extension supported. <5>[ 9.438894] Registering SWP/SWPB emulation handler <6>[ 9.441169] printk: console [ttymxc0]: printing thread started <5>[ 9.441232] Loading compiled-in X.509 certificates <6>[ 9.467388] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <4>[ 9.471780] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 9.475925] panel-simple panel: supply power not found, using dummy regulator <4>[ 9.476295] panel-simple panel: Specify missing connector_type <6>[ 9.875868] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA <4>[ 9.880250] imx_usb 2184000.usb: No over current polarity defined <6>[ 9.907674] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 9.907756] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.935307] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 9.937191] hub 1-0:1.0: USB hub found <6>[ 9.937350] hub 1-0:1.0: 1 port detected <6>[ 9.942945] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 9.974674] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 9.979503] panel-simple panel: supply power not found, using dummy regulator <4>[ 9.979894] panel-simple panel: Specify missing connector_type <4>[ 9.986446] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 9.991341] panel-simple panel: supply power not found, using dummy regulator <4>[ 9.991732] panel-simple panel: Specify missing connector_type <4>[ 10.076183] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 10.082750] mmc1: new high speed SDHC card at address aaaa <6>[ 10.085537] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <6>[ 10.111530] mmcblk1: p1 p2 <4>[ 10.119085] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 10.119640] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <4>[ 10.123618] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.123926] panel-simple panel: Specify missing connector_type <6>[ 10.211731] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 13.286744] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 13.304850] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 13.336107] Sending DHCP requests .., OK <6>[ 16.096239] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.160 <6>[ 16.096312] IP-Config: Complete: <6>[ 16.096328] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.160, mask=255.255.255.0, gw=172.16.1.4 <6>[ 16.096389] host=172.16.1.160, domain=example.org, nis-domain=(none) <6>[ 16.096418] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 16.096451] nameserver0=172.16.1.4 <6>[ 16.155939] Freeing unused kernel memory: 2048K <6>[ 16.176969] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.430619] udevd[127]: starting version 3.2.9 <5>[ 16.432335] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.432785] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.432995] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 16.473395] udevd[127]: specified user 'tss' unknown <27>[ 16.474038] udevd[127]: specified group 'tss' unknown <30>[ 16.486343] udevd[128]: starting eudev-3.2.9 <4>[ 19.769834] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 19.774062] panel-simple panel: supply power not found, using dummy regulator <4>[ 19.774444] panel-simple panel: Specify missing connector_type <6>[ 20.479275] caam 2140000.crypto: RNG4 SH0 was previously instantiated without prediction resistance. Tearing it down <6>[ 20.479324] caam 2140000.crypto: Deinstantiated RNG4 SH0 <6>[ 20.479354] caam 2140000.crypto: Instantiated RNG4 SH0 <6>[ 20.479367] caam 2140000.crypto: RNG4 SH1 was previously instantiated without prediction resistance. Tearing it down <6>[ 20.479392] caam 2140000.crypto: Deinstantiated RNG4 SH1 <6>[ 20.491844] caam 2140000.crypto: Instantiated RNG4 SH1 <6>[ 20.491873] caam 2140000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 20.491888] caam 2140000.crypto: job rings = 3, qi = 0 <4>[ 20.562995] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 20.587777] panel-simple panel: supply power not found, using dummy regulator <4>[ 20.588139] panel-simple panel: Specify missing connector_type <6>[ 21.339888] spi-nor spi4.0: n25q256a (32768 Kbytes) <4>[ 21.360113] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 21.364395] panel-simple panel: supply power not found, using dummy regulator <4>[ 21.364765] panel-simple panel: Specify missing connector_type <6>[ 21.581385] gpio@0 enforce active low on chipselect handle <4>[ 21.628402] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 21.632476] panel-simple panel: supply power not found, using dummy regulator <4>[ 21.632826] panel-simple panel: Specify missing connector_type <6>[ 23.307779] caam algorithms registered in /proc/crypto <6>[ 23.316884] caam 2140000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 23.316918] caam 2140000.crypto: registering rng-caam <4>[ 23.322412] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.351772] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.352150] panel-simple panel: Specify missing connector_type <5>[ 23.369989] random: crng init done <4>[ 23.379877] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.386259] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.386603] panel-simple panel: Specify missing connector_type done <4>[ 23.476684] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.482934] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.483269] panel-simple panel: Specify missing connector_type Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181717/environment . /lava-1181717/environment / # /lava-1181717/bin/lava-test-runner /lava-1181717/0 /lava-1181717/bin/lava-test-runner /lava-1181717/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1181717/0/tests/0_dmesg + cat uuid + UUID=1181717_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 29.549729] <8>[ 29.618055] <8>[ 29.678764] + set +x <8>[ 29.739304] / # # <8>[ 29.741486] #export SHELL=/bin/sh / # export SHELL=/bin/sh . /lava-1181717/environment / # . /lava-1181717/environment /lava-1181717/bin/lava-test-runner /lava-1181717/1 / # /lava-1181717/bin/lava-test-runner /lava-1181717/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1181717/1/tests/1_bootrr + cat uuid + UUID=1181717_1.5.2.4.5<8>[ 35.513010] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1181717/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto regulator-can-3v3 backlight-display panel 2090000.flexcan 2094000.flexcan sound 21c8000.lcdif /lava-1181717/1/../bin/lava-test-case <8>[ 36.614778] /lava-1181717/1/../bin/lava-test-case <8>[ 36.671497] /lava-1181717/1/../bin/lava-test-case <8>[ 36.705530] + set +x / #