Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.9 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 953475/tftp-deploy-zmrhgvhg/kernel/zImage tftp 0x82000000 953475/tftp-deploy-zmrhgvhg/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '953475/tftp-deploy-zmrhgvhg/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.2 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x83000000 953475/tftp-deploy-zmrhgvhg/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 953475/tftp-deploy-zmrhgvhg/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '953475/tftp-deploy-zmrhgvhg/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.1 MiB/s done Bytes transferred = 16073332 (f54274 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 953475/tftp-deploy-zmrhgvhg/dtb/am335x-boneblack.dtb tftp 0x88000000 953475/tftp-deploy-zmrhgvhg/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '953475/tftp-deploy-zmrhgvhg/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-06-05 17:29:46 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16073268 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.180-cip34 (KernelCI@build-j1610394-arm-gcc-10-multi-v7-defconfig-sj7dv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Jun 5 16:55:49 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 410848K/522240K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 45856K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000012] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008339] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019137] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033633] Console: colour dummy device 80x30 <3>[ 0.038499] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045544] This ensures that you still see kernel messages. Please <3>[ 0.052263] update your kernel commandline. <6>[ 0.056869] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096106] pid_max: default: 32768 minimum: 301 <6>[ 0.101313] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.109103] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.118098] CPU: Testing write buffer coherency: ok <6>[ 0.123487] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.129279] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135581] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144948] rcu: Hierarchical SRCU implementation. <6>[ 0.155299] EFI services will not be available. <6>[ 0.160479] smp: Bringing up secondary CPUs ... <6>[ 0.165409] smp: Brought up 1 node, 1 CPU <6>[ 0.169827] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.176540] CPU: All CPU(s) started in SVC mode. <6>[ 0.182161] devtmpfs: initialized <6>[ 0.196303] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.204831] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.215264] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.226480] pinctrl core: initialized pinctrl subsystem <6>[ 0.234882] DMI not present or invalid. <6>[ 0.239933] NET: Registered protocol family 16 <6>[ 0.247230] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.273826] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.282066] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.282268] cpuidle: using governor menu <6>[ 1.345147] No ATAGs? <6>[ 1.347773] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.362728] Serial: AMBA PL011 UART driver <6>[ 1.401341] iommu: Default domain type: Translated <6>[ 1.407073] vgaarb: loaded <5>[ 1.411208] SCSI subsystem initialized <6>[ 1.416220] usbcore: registered new interface driver usbfs <6>[ 1.422275] usbcore: registered new interface driver hub <6>[ 1.428055] usbcore: registered new device driver usb <6>[ 1.435457] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.440892] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.450585] PTP clock support registered <6>[ 1.458724] clocksource: Switched to clocksource dmtimer <6>[ 2.429669] NET: Registered protocol family 2 <6>[ 2.434709] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.443236] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.452172] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.460460] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.468113] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.475045] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.482072] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.489658] NET: Registered protocol family 1 <6>[ 2.495254] RPC: Registered named UNIX socket transport module. <6>[ 2.501696] RPC: Registered udp transport module. <6>[ 2.506800] RPC: Registered tcp transport module. <6>[ 2.511924] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.518844] PCI: CLS 0 bytes, default 64 <6>[ 2.523840] Trying to unpack rootfs image as initramfs... <6>[ 3.589263] Freeing initrd memory: 15700K <6>[ 3.594633] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.604997] Initialise system trusted keyrings <6>[ 3.610362] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.623427] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.630774] NFS: Registering the id_resolver key type <5>[ 3.636290] Key type id_resolver registered <5>[ 3.640918] Key type id_legacy registered <6>[ 3.645424] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.652630] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.660555] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.665869] Key type asymmetric registered <5>[ 3.670401] Asymmetric key parser 'x509' registered <6>[ 3.675732] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.683631] io scheduler mq-deadline registered <6>[ 3.688557] io scheduler kyber registered <3>[ 3.842931] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.851624] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.971733] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.017134] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.095598] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.104300] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.169876] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.178498] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.197117] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.205834] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.274780] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.283337] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.326229] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.431966] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.444290] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.453728] printk: console [ttyS0] enabled <6>[ 4.453728] printk: console [ttyS0] enabled <6>[ 4.462784] printk: bootconsole [omap8250] disabled <6>[ 4.462784] printk: bootconsole [omap8250] disabled <6>[ 4.476655] SuperH (H)SCI(F) driver initialized <6>[ 4.483838] msm_serial: driver initialized <6>[ 4.488632] STMicroelectronics ASC driver initialized <6>[ 4.496985] STM32 USART driver initialized <6>[ 4.504493] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.525760] random: crng init done <6>[ 4.539139] brd: module loaded <6>[ 4.550167] loop: module loaded <6>[ 4.576063] CAN device driver interface <6>[ 4.582336] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.590792] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.596053] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.602434] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.608121] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.678817] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.715187] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.725116] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.731817] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.737653] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.746816] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.754748] usbcore: registered new interface driver pegasus <6>[ 4.760781] usbcore: registered new interface driver asix <6>[ 4.766501] usbcore: registered new interface driver ax88179_178a <6>[ 4.772938] usbcore: registered new interface driver cdc_ether <6>[ 4.779140] usbcore: registered new interface driver smsc75xx <6>[ 4.785213] usbcore: registered new interface driver smsc95xx <6>[ 4.791315] usbcore: registered new interface driver net1080 <6>[ 4.797291] usbcore: registered new interface driver cdc_subset <6>[ 4.803547] usbcore: registered new interface driver zaurus <6>[ 4.809488] usbcore: registered new interface driver cdc_ncm <6>[ 4.821312] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.828150] ehci-pci: EHCI PCI platform driver <6>[ 4.832994] ehci-platform: EHCI generic platform driver <6>[ 4.839066] ehci-orion: EHCI orion driver <6>[ 4.843735] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.848327] ehci-st: EHCI STMicroelectronics driver <6>[ 4.853857] ehci-exynos: EHCI Exynos driver <6>[ 4.858637] ehci-atmel: EHCI Atmel driver <6>[ 4.863289] tegra-ehci: Tegra EHCI driver <6>[ 4.867919] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.874483] ohci-pci: OHCI PCI platform driver <6>[ 4.879314] ohci-platform: OHCI generic platform driver <6>[ 4.885278] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.889960] ohci-st: OHCI STMicroelectronics driver <6>[ 4.895432] ohci-atmel: OHCI Atmel driver <6>[ 4.901811] usbcore: registered new interface driver usb-storage <6>[ 4.919534] i2c /dev entries driver <5>[ 4.952914] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.961309] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.967793] sdhci: Copyright(c) Pierre Ossman <6>[ 4.977042] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.986584] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 5.001818] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.061705] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.071334] usbcore: registered new interface driver usbhid <6>[ 5.077272] usbhid: USB HID core driver <6>[ 5.091326] NET: Registered protocol family 10 <6>[ 5.097536] Segment Routing with IPv6 <6>[ 5.101643] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.108602] NET: Registered protocol family 17 <6>[ 5.113433] can: controller area network core <6>[ 5.118156] NET: Registered protocol family 29 <6>[ 5.122934] can: raw protocol <6>[ 5.126181] can: broadcast manager protocol <6>[ 5.130674] can: netlink gateway - max_hops=1 <5>[ 5.136080] Key type dns_resolver registered <6>[ 5.140847] ThumbEE CPU extension supported. <5>[ 5.145417] Registering SWP/SWPB emulation handler <3>[ 5.150965] omap_voltage_late_init: Voltage driver support not added <6>[ 5.159226] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 5.167975] Loading compiled-in X.509 certificates <6>[ 5.189797] OMAP GPIO hardware version 0.1 <4>[ 5.219317] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 5.232580] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 5.247918] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 5.254288] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 5.261671] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 5.269654] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 5.279604] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 5.289352] mmc1: new high speed MMC card at address 0001 <6>[ 5.295920] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.301178] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.307708] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.314341] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.323856] mmcblk1: p1 <4>[ 5.327987] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.362977] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.402554] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.441580] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.465460] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.474642] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.479770] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.567690] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.609872] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.700588] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 10.919676] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 10.938897] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.968881] Sending DHCP requests ., OK <6>[ 11.012985] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.9 <6>[ 11.021135] IP-Config: Complete: <6>[ 11.024675] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.9, mask=255.255.255.0, gw=192.168.11.1 <6>[ 11.035262] host=192.168.11.9, domain=usen.ad.jp, nis-domain=(none) <6>[ 11.042349] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 11.042369] nameserver0=192.168.11.1 <6>[ 11.066277] Freeing unused kernel memory: 2048K <6>[ 11.089947] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.292946] udevd[97]: starting version 3.2.9 <27>[ 11.309341] udevd[97]: specified user 'tss' unknown <27>[ 11.314826] udevd[97]: specified group 'tss' unknown <30>[ 11.330804] udevd[98]: starting eudev-3.2.9 <4>[ 13.011396] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 13.020498] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 13.280253] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 13.289396] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 13.495997] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 13.501844] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 13.739039] hub 1-0:1.0: USB hub found <6>[ 13.780438] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-953475/environment . /lava-953475/environment / # /lava-953475/bin/lava-test-runner /lava-953475/0 /lava-953475/bin/lava-test-runner /lava-953475/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-953475/0/tests/0_dmesg + cat uuid + UUID=953475_1.5.2.4.1 + <8>[ 18.576186] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.633806] <8>[ 18.685650] <8>[ 18.737659] + set +x <8>[ 18.748966] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-953475/environment / # . /lava-953475/environment/lava-953475/bin/lava-test-runner /lava-953475/1 / # /lava-953475/bin/lava-test-runner /lava-953475/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-953475/1/tests/1_bootrr + cat uuid + UUID=953475_1.5.2.4.5 + <8>[ 19.261353] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-953475/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-953475/1/../bin/lava-test-case <8>[ 20.355964] /lava-953475/1/../bin/lava-test-case <8>[ 20.405085] /lava-953475/1/../bin/lava-test-case <8>[ 20.434934] /lava-953475/1/../bin/lava-test-case <8>[ 20.489893] /lava-953475/1/../bin/lava-test-case <8>[ 20.536164] /lava-953475/1/../bin/lava-test-case <8>[ 20.573386] /lava-953475/1/../bin/lava-test-case <8>[ 20.619573] /lava-953475/1/../bin/lava-test-case <8>[ 20.664797] /lava-953475/1/../bin/lava-test-case <8>[ 20.701729] /lava-953475/1/../bin/lava-test-case <8>[ 20.747261] /lava-953475/1/../bin/lava-test-case <8>[ 21.807977] /lava-953475/1/../bin/lava-test-case <8>[ 22.869273] /lava-953475/1/../bin/lava-test-case <8>[ 22.905598] /lava-953475/1/../bin/lava-test-case <8>[ 22.941651] /lava-953475/1/../bin/lava-test-case <8>[ 22.978082] /lava-953475/1/../bin/lava-test-case <8>[ 23.023811] /lava-953475/1/../bin/lava-test-case <8>[ 23.061811] /lava-953475/1/../bin/lava-test-case <8>[ 23.107964] /lava-953475/1/../bin/lava-test-case <8>[ 23.153154] /lava-953475/1/../bin/lava-test-case <8>[ 23.190327] /lava-953475/1/../bin/lava-test-case <8>[ 23.236253] /lava-953475/1/../bin/lava-test-case <8>[ 23.282284] /lava-953475/1/../bin/lava-test-case <8>[ 23.319791] /lava-953475/1/../bin/lava-test-case <8>[ 23.366417] /lava-953475/1/../bin/lava-test-case <8>[ 23.403816] /lava-953475/1/../bin/lava-test-case <8>[ 23.450210] /lava-953475/1/../bin/lava-test-case <8>[ 24.514465] /lava-953475/1/../bin/lava-test-case <8>[ 25.577383] /lava-953475/1/../bin/lava-test-case <8>[ 25.615096] /lava-953475/1/../bin/lava-test-case <8>[ 25.662092] /lava-953475/1/../bin/lava-test-case <8>[ 25.699328] /lava-953475/1/../bin/lava-test-case <8>[ 25.744973] /lava-953475/1/../bin/lava-test-case <8>[ 26.807064] /lava-953475/1/../bin/lava-test-case <8>[ 27.868042] /lava-953475/1/../bin/lava-test-case <8>[ 27.904976] /lava-953475/1/../bin/lava-test-case <8>[ 27.951500] /lava-953475/1/../bin/lava-test-case <8>[ 29.015354] /lava-953475/1/../bin/lava-test-case <8>[ 30.070855] /lava-953475/1/../bin/lava-test-case <8>[ 31.136178] /lava-953475/1/../bin/lava-test-case <8>[ 32.198060] /lava-953475/1/../bin/lava-test-case <8>[ 33.257966] /lava-953475/1/../bin/lava-test-case <8>[ 34.319191] /lava-953475/1/../bin/lava-test-case <8>[ 35.384606] /lava-953475/1/../bin/lava-test-case <8>[ 36.446702] /lava-953475/1/../bin/lava-test-case <8>[ 37.508066] /lava-953475/1/../bin/lava-test-case <8>[ 38.569404] /lava-953475/1/../bin/lava-test-case <8>[ 39.629173] /lava-953475/1/../bin/lava-test-case <8>[ 40.694957] /lava-953475/1/../bin/lava-test-case <8>[ 41.757083] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-953475/1/../bin/lava-test-case <8>[ 41.796174] /lava-953475/1/../bin/lava-test-case <8>[ 42.866821] /lava-953475/1/../bin/lava-test-case <8>[ 43.927285] + set +x <8>[ 43.942723] / #