[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 8785233/tftp-deploy-3gpaggid/kernel/zImage tftp 0x10000000 8785233/tftp-deploy-3gpaggid/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '8785233/tftp-deploy-3gpaggid/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x14000000 8785233/tftp-deploy-3gpaggid/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8785233/tftp-deploy-3gpaggid/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '8785233/tftp-deploy-3gpaggid/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 2.8 MiB/s done Bytes transferred = 9400036 (8f6ee4 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8785233/tftp-deploy-3gpaggid/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8785233/tftp-deploy-3gpaggid/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '8785233/tftp-deploy-3gpaggid/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.1 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/8785233/extract-nfsrootfs-gyx73rpl,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/8785233/extract-nfsrootfs-gyx73rpl,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9399972 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip88-rt28 (KernelCI@build-j877170-arm-gcc-10-defconfig-qf728) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Jan 18 20:42:03 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/8785233/extract-nfsrootfs-gyx73rpl,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 942968K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 40072K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000006] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008093] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021034] Console: colour dummy device 80x30 <6>[ 0.022918] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.033597] pid_max: default: 32768 minimum: 301 <6>[ 0.038595] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045341] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053167] CPU: Testing write buffer coherency: ok <6>[ 0.057786] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063436] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069674] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077402] rcu: Hierarchical SRCU implementation. <6>[ 0.084168] EFI services will not be available. <6>[ 0.086408] smp: Bringing up secondary CPUs ... <6>[ 0.091777] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091783] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103105] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103112] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114315] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114320] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124676] smp: Brought up 1 node, 4 CPUs <6>[ 0.128930] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.135432] CPU: All CPU(s) started in SVC mode. <6>[ 0.141379] devtmpfs: initialized <6>[ 0.151203] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156649] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166409] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175963] pinctrl core: initialized pinctrl subsystem <6>[ 0.180185] DMI not present or invalid. <6>[ 0.183529] NET: Registered protocol family 16 <6>[ 0.190915] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197565] cpuidle: using governor menu <6>[ 0.199562] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.214482] vdd1p1: supplied by regulator-dummy <6>[ 0.216952] vdd3p0: supplied by regulator-dummy <6>[ 0.221688] vdd2p5: supplied by regulator-dummy <6>[ 0.226511] vddarm: supplied by regulator-dummy <6>[ 0.231420] vddpu: supplied by regulator-dummy <6>[ 0.235861] vddsoc: supplied by regulator-dummy <6>[ 0.254470] No ATAGs? <6>[ 0.254598] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262553] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271941] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278814] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290537] Serial: AMBA PL011 UART driver <6>[ 0.294327] console [pstore-1] enabled <6>[ 0.296206] pstore: Registered ramoops as persistent store backend <6>[ 0.302497] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.330685] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340067] vgaarb: loaded <5>[ 0.340977] SCSI subsystem initialized <6>[ 0.344629] usbcore: registered new interface driver usbfs <6>[ 0.349965] usbcore: registered new interface driver hub <6>[ 0.355552] usbcore: registered new device driver usb <6>[ 0.362058] i2c i2c-0: IMX I2C adapter registered <6>[ 0.365767] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.371898] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376295] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382292] i2c i2c-2: IMX I2C adapter registered <6>[ 0.386817] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.393911] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.397600] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407027] PTP clock support registered <6>[ 0.411387] EDAC MC: Ver: 3.0.0 <6>[ 0.417295] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.479470] NET: Registered protocol family 2 <6>[ 0.481675] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.489235] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.496146] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.503536] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.510287] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.516946] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.522982] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.529703] NET: Registered protocol family 1 <6>[ 0.534707] RPC: Registered named UNIX socket transport module. <6>[ 0.540343] RPC: Registered udp transport module. <6>[ 0.545272] RPC: Registered tcp transport module. <6>[ 0.550243] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.557475] Trying to unpack rootfs image as initramfs... <6>[ 1.283772] Freeing initrd memory: 9180K <4>[ 1.285617] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.292836] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.302796] Initialise system trusted keyrings <6>[ 1.305891] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.318392] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.322362] NFS: Registering the id_resolver key type <5>[ 1.326989] Key type id_resolver registered <5>[ 1.331409] Key type id_legacy registered <6>[ 1.335681] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.342480] Key type asymmetric registered <5>[ 1.344607] Asymmetric key parser 'x509' registered <6>[ 1.349800] bounce: pool size: 64 pages <6>[ 1.353863] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.361508] io scheduler noop registered <6>[ 1.365659] io scheduler deadline registered <6>[ 1.370421] io scheduler cfq registered (default) <6>[ 1.375143] io scheduler mq-deadline registered <6>[ 1.379946] io scheduler kyber registered <6>[ 1.405587] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.410168] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.417244] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.424579] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.444478] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.447905] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.455687] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.461919] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.469851] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.477317] PU : no governor for states <6>[ 1.479414] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.483491] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.552916] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.560133] SuperH (H)SCI(F) driver initialized <6>[ 1.562988] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.571767] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.582709] console [ttymxc1] enabled <6>[ 1.582709] console [ttymxc1] enabled <6>[ 1.587707] bootconsole [ec_imx21] disabled <6>[ 1.587707] bootconsole [ec_imx21] disabled <6>[ 1.597818] msm_serial: driver initialized <6>[ 1.604006] STMicroelectronics ASC driver initialized <6>[ 1.610702] STM32 USART driver initialized <4>[ 1.625799] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 1.634499] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 1.641507] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 1.648311] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 1.657362] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 1.664511] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 1.679249] brd: module loaded <6>[ 1.692133] loop: module loaded <6>[ 1.698760] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 1.706953] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 1.715258] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 1.723724] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 1.734503] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 1.741785] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 1.750858] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 1.761715] scsi host0: ahci-imx <6>[ 1.765773] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 1.784509] CAN device driver interface <6>[ 1.789888] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.796920] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 1.805883] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.814988] pps pps0: new PPS source ptp0 <6>[ 1.837063] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 1.844511] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 1.850634] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.856876] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 1.864120] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.875782] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 1.883511] usbcore: registered new interface driver pegasus <6>[ 1.889497] usbcore: registered new interface driver asix <6>[ 1.895196] usbcore: registered new interface driver ax88179_178a <6>[ 1.901611] usbcore: registered new interface driver cdc_ether <6>[ 1.907778] usbcore: registered new interface driver smsc75xx <6>[ 1.913832] usbcore: registered new interface driver smsc95xx <6>[ 1.919894] usbcore: registered new interface driver net1080 <6>[ 1.925850] usbcore: registered new interface driver cdc_subset <6>[ 1.932083] usbcore: registered new interface driver zaurus <6>[ 1.938014] usbcore: registered new interface driver cdc_ncm <6>[ 1.946806] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.953625] ehci-pci: EHCI PCI platform driver <6>[ 1.958389] ehci-platform: EHCI generic platform driver <6>[ 1.964172] ehci-orion: EHCI orion driver <6>[ 1.968691] SPEAr-ehci: EHCI SPEAr driver <6>[ 1.973149] ehci-st: EHCI STMicroelectronics driver <6>[ 1.978498] ehci-exynos: EHCI EXYNOS driver <6>[ 1.983125] ehci-atmel: EHCI Atmel driver <6>[ 1.987611] tegra-ehci: Tegra EHCI driver <6>[ 1.992097] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.998578] ohci-pci: OHCI PCI platform driver <6>[ 2.003330] ohci-platform: OHCI generic platform driver <6>[ 2.009108] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.013568] ohci-st: OHCI STMicroelectronics driver <6>[ 2.018923] ohci-atmel: OHCI Atmel driver <6>[ 2.024178] usbcore: registered new interface driver usb-storage <6>[ 2.032712] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.044789] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.054972] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.060168] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.097350] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.098777] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.103707] hub 1-0:1.0: USB hub found <6>[ 2.108745] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.112767] hub 1-0:1.0: 1 port detected <6>[ 2.119268] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.129579] i2c /dev entries driver <3>[ 2.145653] imx_thermal tempmon: invalid sensor calibration data <3>[ 2.151960] imx_thermal tempmon: failed to init from from fsl,tempmon-data <4>[ 2.159134] imx_thermal: probe of tempmon failed with error -22 <6>[ 2.168483] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.179824] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.186271] sdhci: Copyright(c) Pierre Ossman <6>[ 2.193144] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.201381] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.208194] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.213637] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.219177] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.259012] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.267018] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.272585] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.312638] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.324119] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.331189] usbcore: registered new interface driver usbhid <6>[ 2.337065] usbhid: USB HID core driver <6>[ 2.347013] NET: Registered protocol family 10 <6>[ 2.352856] Segment Routing with IPv6 <6>[ 2.356880] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.363640] NET: Registered protocol family 17 <6>[ 2.368386] can: controller area network core (rev 20170425 abi 9) <6>[ 2.374910] NET: Registered protocol family 29 <6>[ 2.379646] can: raw protocol (rev 20170425) <6>[ 2.384185] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.390135] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.396262] Key type dns_resolver registered <6>[ 2.401634] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.407390] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.413129] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.419624] ThumbEE CPU extension supported. <5>[ 2.424170] Registering SWP/SWPB emulation handler <6>[ 2.427350] usb 1-1: new high-speed USB device number 2 using ci_hdrc <5>[ 2.429808] Loading compiled-in X.509 certificates <6>[ 2.437268] mmc0: new high speed SDHC card at address 0001 <6>[ 2.442620] pstore: Using compression: deflate <6>[ 2.448790] mmcblk0: mmc0:0001 SD 14.8 GiB <6>[ 2.466958] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.469185] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.474410] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 2.481975] GPT:29296874 != 30965759 <6>[ 2.490709] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 2.492904] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.500373] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.506569] GPT:29296874 != 30965759 <4>[ 2.515486] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 2.517565] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.517619] mmcblk0: p1 p2 p3 <6>[ 2.526242] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.541923] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.550130] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.559210] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.566361] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.574346] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.581760] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.590211] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.597707] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.606512] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.615212] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.622208] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 2.629261] hub 1-1:1.0: USB hub found <4>[ 2.630402] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.633391] hub 1-1:1.0: 3 ports detected <6>[ 2.642335] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.653720] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.661707] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.669119] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.677578] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.685056] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.693880] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.702575] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.709561] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.717601] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.726611] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.733771] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.742528] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 2.749486] hctosys: unable to open rtc device (rtc0) <6>[ 2.756147] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.763633] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.772289] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.779806] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.788729] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.797432] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.804406] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.812510] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.821555] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.828731] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.878193] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 2.893127] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 4.957931] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx <6>[ 4.967365] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 4.997443] Sending DHCP requests ., OK <6>[ 5.041539] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 <6>[ 5.049964] IP-Config: Complete: <6>[ 5.053481] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 <6>[ 5.064315] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) <6>[ 5.073324] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= <6>[ 5.073331] nameserver0=192.168.101.1 <6>[ 5.092250] Freeing unused kernel memory: 2048K <6>[ 5.107825] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 6.153003] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.160794] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 6.170053] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.177574] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.186458] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.194026] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.203385] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.212191] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.219438] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.220023] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 6.227934] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.241878] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.249381] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.249512] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.257890] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.270393] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.280019] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.287666] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.294492] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.301010] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.308566] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.314965] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 6.322454] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 6.322546] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.331876] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.336347] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.351263] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.359886] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.368968] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.376127] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.384597] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.392215] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.401332] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.408881] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.418526] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.427255] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.434392] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.443217] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.452339] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.459674] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.487336] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.516120] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.522540] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.530494] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 6.539797] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.547238] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.556598] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.564175] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.574211] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.583032] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.590179] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.599195] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.608319] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.615488] panel-simple panel-lvds0: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:00:e5:47 mtu 1500 DHCP IP-Config: no response after 2 secs - giving up IP-Config: eth0 hardware address 00:19:b8:00:e5:47 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.101 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-2 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.229589] systemd[1]: System time before build time, advancing clock. <3>[ 10.290090] cgroup: cgroup2: unknown option "memory_recursiveprot" <30>[ 10.306510] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.330681] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.369454] systemd[1]: Set hostname to . <30>[ 11.215265] systemd[1]: Queued start job for default target Graphical Interface. <5>[ 11.224936] random: systemd: uninitialized urandom read (16 bytes read) <28>[ 11.232111] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.244898] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.254560] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <5>[ 11.287631] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 11.295622] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <5>[ 11.347690] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 11.355660] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.398459] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.438188] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.478140] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.518093] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.530713] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.567828] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.597940] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.637728] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.667932] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.698628] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.777533] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.787636] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.828970] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.869680] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.910516] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.948867] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.988622] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.998255] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 12.013416] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 12.050958] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 12.206506] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <5>[ 12.248116] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 12.258191] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <5>[ 12.307913] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 12.319620] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <5>[ 12.358358] random: systemd: uninitialized urandom read (16 bytes read) <30>[ 12.371130] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.422269] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.438749] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.504113] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.540613] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.580646] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.623463] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.658410] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.709192] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.767831] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 12.774792] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 12.819162] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 12.825712] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 12.858297] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 13.125544] systemd-journald[170]: Received client request to flush runtime journal. <5>[ 13.147382] random: crng init done <5>[ 13.151065] random: 40 urandom warning(s) missed due to ratelimiting Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Started User Login Management. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.269-cip88-rt28 #1 SMP Wed Jan 18 20:42:03 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8785233/extract-nfsrootfs-gyx73rpl' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/8785233/extract-nfsrootfs-gyx73rpl' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8785233/environment . /lava-8785233/environment / # /lava-8785233/bin/lava-test-runner /lava-8785233/0 /lava-8785233/bin/lava-test-runner /lava-8785233/0 + export TESTRUN_ID=0_dmesg + cd /lava-8785233/0/tests/0_dmesg + cat uuid + UUID=8785233_1.6.2.4.1 <8>[ 30.121854] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 30.253707] <8>[ 30.335055] <8>[ 30.418446] + set +x <8>[ 30.429427] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-8785233/environment / # . /lava-8785233/environment/lava-8785233/bin/lava-test-runner /lava-8785233/1 / # /lava-8785233/bin/lava-test-runner /lava-8785233/1 + export TESTRUN_ID=1_bootrr + cd /lava-8785233/1/tests/1_bootrr + cat uuid + UUID=8785233_1.6.2.4.5 + <8>[ 31.029424] set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-8785233/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-8785233/1/../bin/lava-test-case <8>[ 32.197858] /lava-8785233/1/../bin/lava-test-case <8>[ 32.296431] /lava-8785233/1/../bin/lava-test-case <8>[ 32.350790] + set +x <8>[ 32.388831] / #