[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10419644/tftp-deploy-i4ao1pg3/kernel/zImage tftp 0x10000000 10419644/tftp-deploy-i4ao1pg3/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '10419644/tftp-deploy-i4ao1pg3/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3.5 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp 0x14000000 10419644/tftp-deploy-i4ao1pg3/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10419644/tftp-deploy-i4ao1pg3/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '10419644/tftp-deploy-i4ao1pg3/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 2.9 MiB/s done Bytes transferred = 13339143 (cb8a07 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10419644/tftp-deploy-i4ao1pg3/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10419644/tftp-deploy-i4ao1pg3/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '10419644/tftp-deploy-i4ao1pg3/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13339079 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.280-cip96-rt30 (KernelCI@build-j1546367-arm-gcc-10-defconfig-69lfx) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Tue May 23 00:37:46 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939120K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43920K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021445] Console: colour dummy device 80x30 <6>[ 0.023330] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033747] pid_max: default: 32768 minimum: 301 <6>[ 0.038742] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045491] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053331] CPU: Testing write buffer coherency: ok <6>[ 0.057936] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063587] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069860] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077539] rcu: Hierarchical SRCU implementation. <6>[ 0.084301] EFI services will not be available. <6>[ 0.086551] smp: Bringing up secondary CPUs ... <6>[ 0.091940] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091946] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103269] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103275] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114473] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114480] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124813] smp: Brought up 1 node, 4 CPUs <6>[ 0.129062] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135478] CPU: All CPU(s) started in SVC mode. <6>[ 0.141450] devtmpfs: initialized <6>[ 0.151567] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.157016] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166772] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.176347] pinctrl core: initialized pinctrl subsystem <6>[ 0.180601] DMI not present or invalid. <6>[ 0.183954] NET: Registered protocol family 16 <6>[ 0.191289] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.198126] cpuidle: using governor menu <6>[ 0.199937] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214926] vdd1p1: supplied by regulator-dummy <6>[ 0.217347] vdd3p0: supplied by regulator-dummy <6>[ 0.222150] vdd2p5: supplied by regulator-dummy <6>[ 0.226940] vddarm: supplied by regulator-dummy <6>[ 0.231854] vddpu: supplied by regulator-dummy <6>[ 0.236298] vddsoc: supplied by regulator-dummy <6>[ 0.254989] No ATAGs? <6>[ 0.255120] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.263087] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.272578] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.279476] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.291381] Serial: AMBA PL011 UART driver <6>[ 0.295204] console [pstore-1] enabled <6>[ 0.297102] pstore: Registered ramoops as persistent store backend <6>[ 0.303326] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331664] mxs-dma 110000.dma-apbh: initialized <6>[ 0.341158] vgaarb: loaded <5>[ 0.342129] SCSI subsystem initialized <6>[ 0.345715] usbcore: registered new interface driver usbfs <6>[ 0.351063] usbcore: registered new interface driver hub <6>[ 0.356643] usbcore: registered new device driver usb <6>[ 0.363122] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366874] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372980] i2c i2c-1: IMX I2C adapter registered <6>[ 0.377398] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.383354] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387923] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.395055] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398690] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.408116] PTP clock support registered <6>[ 0.412495] EDAC MC: Ver: 3.0.0 <6>[ 0.418463] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481359] NET: Registered protocol family 2 <6>[ 0.483565] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.491119] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.498036] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505430] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512169] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518848] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524837] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531601] NET: Registered protocol family 1 <6>[ 0.536617] RPC: Registered named UNIX socket transport module. <6>[ 0.542232] RPC: Registered udp transport module. <6>[ 0.547161] RPC: Registered tcp transport module. <6>[ 0.552134] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559320] Trying to unpack rootfs image as initramfs... <6>[ 1.678749] Freeing initrd memory: 13028K <4>[ 1.680699] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.687952] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.697957] Initialise system trusted keyrings <6>[ 1.700920] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.713388] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.717339] NFS: Registering the id_resolver key type <5>[ 1.722028] Key type id_resolver registered <5>[ 1.726376] Key type id_legacy registered <6>[ 1.730698] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.737390] Key type asymmetric registered <5>[ 1.739632] Asymmetric key parser 'x509' registered <6>[ 1.744777] bounce: pool size: 64 pages <6>[ 1.748882] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.756483] io scheduler noop registered <6>[ 1.760672] io scheduler deadline registered <6>[ 1.765405] io scheduler cfq registered (default) <6>[ 1.770158] io scheduler mq-deadline registered <6>[ 1.774925] io scheduler kyber registered <6>[ 1.801274] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.805818] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.812975] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.820262] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.840728] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.844116] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.851968] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.858142] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.866088] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.868479] PU : no governor for states <6>[ 1.875664] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.879757] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.951753] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.959097] SuperH (H)SCI(F) driver initialized <6>[ 1.961949] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.970711] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.981676] console [ttymxc1] enabled <6>[ 1.981676] console [ttymxc1] enabled <6>[ 1.986658] bootconsole [ec_imx21] disabled <6>[ 1.986658] bootconsole [ec_imx21] disabled <6>[ 1.996767] msm_serial: driver initialized <6>[ 2.003035] STMicroelectronics ASC driver initialized <6>[ 2.010236] STM32 USART driver initialized <4>[ 2.025452] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.034151] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.041145] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.047896] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.056957] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.064135] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.078881] brd: module loaded <6>[ 2.091781] loop: module loaded <6>[ 2.098398] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.106624] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.114922] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.123383] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.134181] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.141467] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.150541] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.161339] scsi host0: ahci-imx <6>[ 2.165408] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.184487] CAN device driver interface <6>[ 2.189867] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.196942] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.205904] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.214985] pps pps0: new PPS source ptp0 <6>[ 2.246178] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.253624] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.259746] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.265984] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.273229] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.284963] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.292699] usbcore: registered new interface driver pegasus <6>[ 2.298687] usbcore: registered new interface driver asix <6>[ 2.304389] usbcore: registered new interface driver ax88179_178a <6>[ 2.310799] usbcore: registered new interface driver cdc_ether <6>[ 2.316941] usbcore: registered new interface driver smsc75xx <6>[ 2.323023] usbcore: registered new interface driver smsc95xx <6>[ 2.329088] usbcore: registered new interface driver net1080 <6>[ 2.335044] usbcore: registered new interface driver cdc_subset <6>[ 2.341277] usbcore: registered new interface driver zaurus <6>[ 2.347183] usbcore: registered new interface driver cdc_ncm <6>[ 2.356068] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.362897] ehci-pci: EHCI PCI platform driver <6>[ 2.367648] ehci-platform: EHCI generic platform driver <6>[ 2.373458] ehci-orion: EHCI orion driver <6>[ 2.377952] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.382439] ehci-st: EHCI STMicroelectronics driver <6>[ 2.387773] ehci-exynos: EHCI EXYNOS driver <6>[ 2.392436] ehci-atmel: EHCI Atmel driver <6>[ 2.396894] tegra-ehci: Tegra EHCI driver <6>[ 2.401407] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.407868] ohci-pci: OHCI PCI platform driver <6>[ 2.412649] ohci-platform: OHCI generic platform driver <6>[ 2.418403] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.422891] ohci-st: OHCI STMicroelectronics driver <6>[ 2.428218] ohci-atmel: OHCI Atmel driver <6>[ 2.433541] usbcore: registered new interface driver usb-storage <6>[ 2.442090] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.454136] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.464296] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.469494] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.498497] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.499946] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.504867] hub 1-0:1.0: USB hub found <6>[ 2.509881] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.513905] hub 1-0:1.0: 1 port detected <6>[ 2.520417] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.530881] i2c /dev entries driver <6>[ 2.550309] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.561772] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.568220] sdhci: Copyright(c) Pierre Ossman <6>[ 2.575160] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.583444] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.590263] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.595697] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.601221] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.641087] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.649133] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.654638] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.694491] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.705954] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.713025] usbcore: registered new interface driver usbhid <6>[ 2.718889] usbhid: USB HID core driver <6>[ 2.728928] NET: Registered protocol family 10 <6>[ 2.734717] Segment Routing with IPv6 <6>[ 2.738770] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.745506] NET: Registered protocol family 17 <6>[ 2.750256] can: controller area network core (rev 20170425 abi 9) <6>[ 2.756774] NET: Registered protocol family 29 <6>[ 2.761510] can: raw protocol (rev 20170425) <6>[ 2.766049] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.771999] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.778151] Key type dns_resolver registered <6>[ 2.783727] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.789505] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.795224] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.801694] ThumbEE CPU extension supported. <5>[ 2.806241] Registering SWP/SWPB emulation handler <6>[ 2.808506] usb 1-1: new high-speed USB device number 2 using ci_hdrc <5>[ 2.811910] Loading compiled-in X.509 certificates <6>[ 2.819395] mmc0: new high speed SDHC card at address 0001 <6>[ 2.824690] pstore: Using compression: deflate <6>[ 2.835317] mmcblk0: mmc0:0001 SD 14.6 GiB <6>[ 2.846349] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <4>[ 2.851923] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.853785] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <4>[ 2.861362] GPT:7812499 != 30560255 <6>[ 2.869931] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <4>[ 2.872187] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.879637] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.885836] GPT:7812499 != 30560255 <4>[ 2.894509] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 2.896734] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.905431] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.910807] mmcblk0: p1 p2 p3 <6>[ 2.917706] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.929007] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.938013] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.945168] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.953863] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.964330] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.971729] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.980084] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.987569] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.996168] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.004849] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.011817] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.019391] hub 1-1:1.0: USB hub found <4>[ 3.019755] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.023548] hub 1-1:1.0: 3 ports detected <6>[ 3.032427] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.043804] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.051641] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.059044] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.067276] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.074770] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.083323] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.092003] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.098967] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.106750] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.115777] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.122924] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.130686] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.138037] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.146203] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.153683] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.162247] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.170922] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.177872] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.185685] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.194709] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.201861] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.210327] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.217204] hctosys: unable to open rtc device (rtc0) <6>[ 3.223720] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.231160] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.239726] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.247172] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.255832] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.264513] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.271490] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.279378] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.288384] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.295527] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.428926] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.443875] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.519170] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 5.548590] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.578650] Sending DHCP requests ., OK <6>[ 5.622712] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 5.631054] IP-Config: Complete: <6>[ 5.634569] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 5.645315] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 5.653457] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 5.653464] nameserver0=192.168.201.1 <6>[ 5.672297] Freeing unused kernel memory: 2048K <6>[ 5.688876] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.819712] udevd[113]: starting version 3.2.9 <5>[ 5.825247] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.832303] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.839121] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.852965] udevd[113]: specified user 'tss' unknown <27>[ 5.858406] udevd[113]: specified group 'tss' unknown <30>[ 5.865848] udevd[114]: starting eudev-3.2.9 <6>[ 6.197839] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.205329] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.214577] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.222491] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.231212] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 6.231852] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.238318] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.246638] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.260425] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 6.267349] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 6.267503] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 6.275069] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <4>[ 6.275497] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.275569] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.275637] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.281272] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 6.319780] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.327164] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.335998] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.343522] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.352709] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.361449] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.368577] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.376933] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.386018] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.393247] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.422354] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 6.445025] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.452616] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.461697] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.469399] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 6.477252] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 6.483661] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 6.490140] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.494470] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 6.498885] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.511131] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.520050] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.529125] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.536276] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.544534] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 6.552802] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 6.559207] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 6.569105] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 6.578372] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.586234] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.595690] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.603701] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.613521] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.622285] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.629681] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.638236] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.647339] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.654879] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 6.663329] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 6.671185] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 6.680469] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 6.688105] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 6.697565] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 6.706312] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 6.713721] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 6.722019] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 6.731107] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 6.738335] panel-simple panel-lvds0: Dropping the link to regulator.0 done Saving random seed: <5>[ 7.001690] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.100212] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10419644/environment . /lava-10419644/environment / # /lava-10419644/bin/lava-test-runner /lava-10419644/0 /lava-10419644/bin/lava-test-runner /lava-10419644/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10419644/0/tests/0_dmesg + cat uuid <8>[ 7.703732] + UUID=10419644_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 7.748170] <8>[ 7.789060] <8>[ 7.830161] + set +x <8>[ 7.840067] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10419644/environment / # . /lava-10419644/environment/lava-10419644/bin/lava-test-runner /lava-10419644/1 / # /lava-10419644/bin/lava-test-runner /lava-10419644/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10419644/1/tests/1_bootrr + cat uuid <8>[ 8.351517] + UUID=10419644_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10419644/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-10419644/1/../bin/lava-test-case <8>[ 9.420473] /lava-10419644/1/../bin/lava-test-case <8>[ 9.460430] /lava-10419644/1/../bin/lava-test-case <8>[ 9.485515] + set +x <8>[ 9.504504] / #