[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 8894178/tftp-deploy-pcjk1yb2/kernel/zImage tftp 0x10000000 8894178/tftp-deploy-pcjk1yb2/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '8894178/tftp-deploy-pcjk1yb2/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.6 MiB/s done Bytes transferred = 9691648 (93e200 hex) => tftp 0x14000000 8894178/tftp-deploy-pcjk1yb2/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 8894178/tftp-deploy-pcjk1yb2/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '8894178/tftp-deploy-pcjk1yb2/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 11.6 MiB/s done Bytes transferred = 16075037 (f5491d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 8894178/tftp-deploy-pcjk1yb2/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 8894178/tftp-deploy-pcjk1yb2/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '8894178/tftp-deploy-pcjk1yb2/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93e200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16074973 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.162-cip24-rt10 (KernelCI@build-j927249-arm-gcc-10-multi-v7-defconfig-4n469) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Jan 27 00:47:40 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933668K/1048576K available (13312K kernel code, 2324K rwdata, 5348K rodata, 2048K init, 417K bss, 49372K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022483] Console: colour dummy device 80x30 <6>[ 0.024373] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034785] pid_max: default: 32768 minimum: 301 <6>[ 0.039812] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047236] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055860] CPU: Testing write buffer coherency: ok <6>[ 0.060353] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065910] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072263] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080057] rcu: Hierarchical SRCU implementation. <6>[ 0.087200] EFI services will not be available. <6>[ 0.089431] smp: Bringing up secondary CPUs ... <6>[ 0.094712] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099840] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106084] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.111062] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117246] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.122284] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127718] smp: Brought up 1 node, 4 CPUs <6>[ 0.131941] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138399] CPU: All CPU(s) started in SVC mode. <6>[ 0.143810] devtmpfs: initialized <6>[ 0.154150] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159490] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169360] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179564] pinctrl core: initialized pinctrl subsystem <6>[ 0.184025] DMI not present or invalid. <6>[ 0.187161] NET: Registered protocol family 16 <6>[ 0.194436] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201079] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201258] cpuidle: using governor menu <6>[ 0.209350] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.386653] vdd1p1: supplied by regulator-dummy <6>[ 0.395670] vdd3p0: supplied by regulator-dummy <6>[ 0.404619] vdd2p5: supplied by regulator-dummy <6>[ 0.413698] vddarm: supplied by regulator-dummy <6>[ 0.422883] vddpu: supplied by regulator-dummy <6>[ 0.431682] vddsoc: supplied by regulator-dummy <6>[ 0.757521] No ATAGs? <6>[ 0.757701] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.765463] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.775810] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.786223] Serial: AMBA PL011 UART driver <6>[ 0.789994] printk: console [ramoops-1] enabled <6>[ 0.792716] pstore: Registered ramoops as persistent store backend <6>[ 0.798977] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.836934] iommu: Default domain type: Translated <6>[ 0.839647] vgaarb: loaded <5>[ 0.843092] SCSI subsystem initialized <7>[ 0.846517] libata version 3.00 loaded. <6>[ 0.850501] usbcore: registered new interface driver usbfs <6>[ 0.856108] usbcore: registered new interface driver hub <6>[ 0.861619] usbcore: registered new device driver usb <6>[ 0.868441] i2c i2c-0: IMX I2C adapter registered <6>[ 0.873205] i2c i2c-1: IMX I2C adapter registered <6>[ 0.877656] i2c i2c-2: IMX I2C adapter registered <6>[ 0.883189] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.887008] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.896417] PTP clock support registered <6>[ 0.904181] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.953620] NET: Registered protocol family 2 <6>[ 1.955841] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.964202] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.971690] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.979772] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.987235] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.993882] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.000603] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.008054] NET: Registered protocol family 1 <6>[ 2.013127] RPC: Registered named UNIX socket transport module. <6>[ 2.018674] RPC: Registered udp transport module. <6>[ 2.023601] RPC: Registered tcp transport module. <6>[ 2.028582] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.035283] PCI: CLS 0 bytes, default 64 <6>[ 2.039910] Trying to unpack rootfs image as initramfs... <6>[ 3.397495] Freeing initrd memory: 15700K <4>[ 3.399417] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.406767] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.416577] Initialise system trusted keyrings <6>[ 3.419672] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.431855] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.435840] NFS: Registering the id_resolver key type <5>[ 3.440465] Key type id_resolver registered <5>[ 3.444874] Key type id_legacy registered <6>[ 3.449212] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.456083] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.463748] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.468815] Key type asymmetric registered <5>[ 3.472684] Asymmetric key parser 'x509' registered <6>[ 3.477881] bounce: pool size: 64 pages <6>[ 3.481941] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.489580] io scheduler mq-deadline registered <6>[ 3.494360] io scheduler kyber registered <6>[ 3.539419] mxs-dma 110000.dma-apbh: initialized <4>[ 3.546319] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.553229] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.617244] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.625629] SuperH (H)SCI(F) driver initialized <6>[ 3.628596] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.637479] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.645415] printk: console [ttymxc1] enabled <6>[ 3.649917] printk: bootconsole [ec_imx21] disabled <6>[ 3.645415] printk: console [ttymxc1] enabled <6>[ 3.649917] printk: bootconsole [ec_imx21] disabled <6>[ 3.656540] msm_serial: driver initialized <6>[ 3.656809] STMicroelectronics ASC driver initialized <6>[ 3.658807] STM32 USART driver initialized <4>[ 3.670764] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.670917] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.671470] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.680075] brd: module loaded <6>[ 3.689929] loop: module loaded <6>[ 3.693858] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.693874] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.693883] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.693892] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.693975] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.694197] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.694260] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.697122] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.697151] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.697169] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.698695] scsi host0: ahci-imx <6>[ 3.699081] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.711848] CAN device driver interface <6>[ 3.713250] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.716863] pps pps0: new PPS source ptp0 <6>[ 3.749806] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.751378] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.751384] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.751440] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.751446] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.757949] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.757993] usbcore: registered new interface driver pegasus <6>[ 3.758033] usbcore: registered new interface driver asix <6>[ 3.758066] usbcore: registered new interface driver ax88179_178a <6>[ 3.758099] usbcore: registered new interface driver cdc_ether <6>[ 3.758141] usbcore: registered new interface driver smsc75xx <6>[ 3.758188] usbcore: registered new interface driver smsc95xx <6>[ 3.758223] usbcore: registered new interface driver net1080 <6>[ 3.758255] usbcore: registered new interface driver cdc_subset <6>[ 3.758285] usbcore: registered new interface driver zaurus <6>[ 3.758351] usbcore: registered new interface driver cdc_ncm <6>[ 3.762161] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.762167] ehci-pci: EHCI PCI platform driver <6>[ 3.762202] ehci-platform: EHCI generic platform driver <6>[ 3.762508] ehci-orion: EHCI orion driver <6>[ 3.762735] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.762925] ehci-st: EHCI STMicroelectronics driver <6>[ 3.763108] ehci-exynos: EHCI Exynos driver <6>[ 3.763296] ehci-atmel: EHCI Atmel driver <6>[ 3.763476] tegra-ehci: Tegra EHCI driver <6>[ 3.763698] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.763716] ohci-pci: OHCI PCI platform driver <6>[ 3.763766] ohci-platform: OHCI generic platform driver <6>[ 3.764043] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.764275] ohci-st: OHCI STMicroelectronics driver <6>[ 3.764471] ohci-atmel: OHCI Atmel driver <6>[ 3.765591] usbcore: registered new interface driver usb-storage <6>[ 3.773935] i2c /dev entries driver <6>[ 3.794026] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.794033] sdhci: Copyright(c) Pierre Ossman <6>[ 3.796918] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.798939] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.804456] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.804491] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.804918] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.805394] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.806532] usbcore: registered new interface driver usbhid <6>[ 3.806540] usbhid: USB HID core driver <6>[ 3.813378] NET: Registered protocol family 10 <6>[ 3.814428] Segment Routing with IPv6 <6>[ 3.814499] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.815066] NET: Registered protocol family 17 <6>[ 3.815081] can: controller area network core <6>[ 3.815151] NET: Registered protocol family 29 <6>[ 3.815158] can: raw protocol <6>[ 3.815165] can: broadcast manager protocol <6>[ 3.815173] can: netlink gateway - max_hops=1 <5>[ 3.815551] Key type dns_resolver registered <6>[ 3.817566] ThumbEE CPU extension supported. <5>[ 3.817581] Registering SWP/SWPB emulation handler <6>[ 3.818033] printk: console [ttymxc1]: printing thread started <6>[ 3.818259] printk: console [ramoops-1]: printing thread started <5>[ 3.818311] Loading compiled-in X.509 certificates <6>[ 3.823440] pstore: Using crash dump compression: deflate <6>[ 3.834532] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.844424] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.844741] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.844896] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.846563] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.855214] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.858737] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.858762] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.871863] mmc2: new high speed SDHC card at address aaaa <6>[ 3.872622] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <4>[ 3.880196] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.880202] GPT:29296874 != 31116287 <4>[ 3.880207] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.880210] GPT:29296874 != 31116287 <4>[ 3.880213] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.880249] mmcblk2: p1 p2 p3 <6>[ 3.894175] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.894774] hub 1-0:1.0: USB hub found <6>[ 3.894809] hub 1-0:1.0: 1 port detected <6>[ 3.897097] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 3.901550] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.901680] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.903108] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.907538] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.907660] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.909055] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.910930] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 3.916581] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.916708] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.918167] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.040699] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.040744] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.040751] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.053097] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.184139] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.405042] hub 1-1:1.0: USB hub found <6>[ 4.405176] hub 1-1:1.0: 3 ports detected <4>[ 4.410310] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.410436] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.411851] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.204692] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.234270] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.264283] Sending DHCP requests ., OK <6>[ 7.304294] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 7.304318] IP-Config: Complete: <6>[ 7.304324] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.304351] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 7.304363] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.304376] nameserver0=192.168.201.1 <6>[ 7.312898] Freeing unused kernel memory: 2048K <6>[ 7.361689] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.477780] udevd[136]: starting version 3.2.9 <5>[ 7.478591] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.478845] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.478944] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.496448] udevd[136]: specified user 'tss' unknown <27>[ 7.496601] udevd[136]: specified group 'tss' unknown <30>[ 7.499110] udevd[137]: starting eudev-3.2.9 <6>[ 7.854972] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 7.860894] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.861048] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.862899] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.927262] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.932716] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.932886] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.935167] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.941130] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.941304] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.965261] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.965396] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.965524] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.965624] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.983215] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.988790] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.988964] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.005933] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.009999] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.031056] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.031167] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.031482] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.031563] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.031578] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.032066] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.115017] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.115088] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.115155] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.115200] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.146346] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.151580] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.151731] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.241899] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.302698] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.363461] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.363482] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.363490] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.366081] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.366153] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.366226] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.366273] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.427746] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.434786] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.434962] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.450043] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.450213] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.450346] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.450460] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.467785] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.467870] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.467979] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.468025] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.469761] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.475833] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.476035] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.480350] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.480414] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.480475] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.480521] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.522537] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.529995] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.530157] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.535388] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.535468] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.535528] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.535573] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.536481] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.540979] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.573988] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.581573] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.581911] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.586885] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.586955] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.587017] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.587064] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.895211] caam algorithms registered in /proc/crypto <6>[ 8.896570] caam 2100000.crypto: registering rng-caam done <4>[ 8.898296] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.903679] panel-simple panel-lcd: supply power not found, using dummy regulator Saving random seed: <4>[ 8.903834] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.909266] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) OK <6>[ 8.909332] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 8.909392] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.909436] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.912033] panel-simple panel-lvds0: supply power not found, using dummy regulator ip: RTNETLINK answers: File exist<4>[ 8.943205] panel-simple panel-lcd: supply power not found, using dummy regulator s <4>[ 8.943366] panel-simple panel-lcd: Specify missing connector_type FAIL <6>[ 8.946536] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.946597] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.946655] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.946700] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <5>[ 8.983648] random: dd: uninitialized urandom read (32 bytes read) Starting dropbear sshd: <5>[ 9.084871] random: crng init done OK <5>[ 9.084880] random: 1 urandom warning(s) missed due to ratelimiting /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-8894178/environment . /lava-8894178/environment / # /lava-8894178/bin/lava-test-runner /lava-8894178/0 /lava-8894178/bin/lava-test-runner /lava-8894178/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-8894178/0/tests/0_dmesg + cat uuid + UUID=8894178_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh<8>[ 9.697126] <8>[ 9.736389] <8>[ 9.769456] <8>[ 9.803181] + set +x <8>[ 9.813013] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-8894178/environment / # . /lava-8894178/environment/lava-8894178/bin/lava-test-runner /lava-8894178/1 / # /lava-8894178/bin/lava-test-runner /lava-8894178/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-8894178/1/tests/1_bootrr + cat uuid + UUID=8894178_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/help<8>[ 10.308369] ers:/lava-8894178/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd 120000.hdmi /lava-8894178/1/../bin/lava-test-case <8>[ 11.372289] /lava-8894178/1/../bin/lava-test-case <8>[ 11.412840] /lava-8894178/1/../bin/lava-test-case <8>[ 11.433106] + set +x / # <8>[ 11.444543]