[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9730550/tftp-deploy-ksosmhrw/kernel/zImage tftp 0x10000000 9730550/tftp-deploy-ksosmhrw/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9730550/tftp-deploy-ksosmhrw/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 6.7 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 9730550/tftp-deploy-ksosmhrw/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9730550/tftp-deploy-ksosmhrw/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9730550/tftp-deploy-ksosmhrw/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 6.9 MiB/s done Bytes transferred = 16078158 (f5554e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9730550/tftp-deploy-ksosmhrw/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9730550/tftp-deploy-ksosmhrw/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9730550/tftp-deploy-ksosmhrw/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16078094 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29-rt12 (KernelCI@build-j1227514-arm-gcc-10-defconfig-7gpjs) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 12:58:35 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932636K/1048576K available (14336K kernel code, 2330K rwdata, 5348K rodata, 2048K init, 415K bss, 50404K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008438] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022155] Console: colour dummy device 80x30 <6>[ 0.024045] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034459] pid_max: default: 32768 minimum: 301 <6>[ 0.039483] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046910] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055515] CPU: Testing write buffer coherency: ok <6>[ 0.060040] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065598] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071951] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079657] rcu: Hierarchical SRCU implementation. <6>[ 0.086635] EFI services will not be available. <6>[ 0.088872] smp: Bringing up secondary CPUs ... <6>[ 0.094168] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.099275] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105505] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.110498] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116703] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.121720] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127149] smp: Brought up 1 node, 4 CPUs <6>[ 0.131376] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137834] CPU: All CPU(s) started in SVC mode. <6>[ 0.143253] devtmpfs: initialized <6>[ 0.153491] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158836] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168705] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178926] pinctrl core: initialized pinctrl subsystem <6>[ 0.183399] DMI not present or invalid. <6>[ 0.186521] NET: Registered protocol family 16 <6>[ 0.193888] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200515] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200694] cpuidle: using governor menu <6>[ 0.208810] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.392780] vdd1p1: supplied by regulator-dummy <6>[ 0.402086] vdd3p0: supplied by regulator-dummy <6>[ 0.411345] vdd2p5: supplied by regulator-dummy <6>[ 0.420580] vddarm: supplied by regulator-dummy <6>[ 0.429990] vddpu: supplied by regulator-dummy <6>[ 0.439023] vddsoc: supplied by regulator-dummy <6>[ 0.777500] No ATAGs? <6>[ 0.777684] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.785443] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.795739] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.806084] Serial: AMBA PL011 UART driver <6>[ 0.809758] printk: console [ramoops-1] enabled <6>[ 0.812579] pstore: Registered ramoops as persistent store backend <6>[ 0.818836] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.856524] iommu: Default domain type: Translated <6>[ 0.859236] vgaarb: loaded <5>[ 0.862664] SCSI subsystem initialized <7>[ 0.866119] libata version 3.00 loaded. <6>[ 0.870098] usbcore: registered new interface driver usbfs <6>[ 0.875699] usbcore: registered new interface driver hub <6>[ 0.881212] usbcore: registered new device driver usb <6>[ 0.888038] i2c i2c-0: IMX I2C adapter registered <6>[ 0.892798] i2c i2c-1: IMX I2C adapter registered <6>[ 0.897246] i2c i2c-2: IMX I2C adapter registered <6>[ 0.902680] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.906601] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.916010] PTP clock support registered <6>[ 0.923672] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.074790] NET: Registered protocol family 2 <6>[ 2.076994] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.085392] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.092862] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.100935] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.108397] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.115084] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.121750] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.129238] NET: Registered protocol family 1 <6>[ 2.134270] RPC: Registered named UNIX socket transport module. <6>[ 2.139812] RPC: Registered udp transport module. <6>[ 2.144803] RPC: Registered tcp transport module. <6>[ 2.149734] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.156454] PCI: CLS 0 bytes, default 64 <6>[ 2.161130] Trying to unpack rootfs image as initramfs... <6>[ 3.525085] Freeing initrd memory: 15704K <4>[ 3.526957] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.534315] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.544148] Initialise system trusted keyrings <6>[ 3.547290] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.559450] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.563417] NFS: Registering the id_resolver key type <5>[ 3.568112] Key type id_resolver registered <5>[ 3.572439] Key type id_legacy registered <6>[ 3.576813] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.583677] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.591350] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.596433] Key type asymmetric registered <5>[ 3.600282] Asymmetric key parser 'x509' registered <6>[ 3.605476] bounce: pool size: 64 pages <6>[ 3.609538] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.617175] io scheduler mq-deadline registered <6>[ 3.621944] io scheduler kyber registered <6>[ 3.665950] mxs-dma 110000.dma-apbh: initialized <4>[ 3.672689] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.679637] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.736106] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.744334] SuperH (H)SCI(F) driver initialized <6>[ 3.747247] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.756182] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.764128] printk: console [ttymxc1] enabled <6>[ 3.768624] printk: bootconsole [ec_imx21] disabled <6>[ 3.764128] printk: console [ttymxc1] enabled <6>[ 3.768624] printk: bootconsole [ec_imx21] disabled <6>[ 3.775222] msm_serial: driver initialized <6>[ 3.775483] STMicroelectronics ASC driver initialized <6>[ 3.777449] STM32 USART driver initialized <4>[ 3.788287] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.788438] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.788815] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.797577] brd: module loaded <6>[ 3.807416] loop: module loaded <6>[ 3.811328] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.811343] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.811353] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.811361] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.811438] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.811581] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.811652] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.813743] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.813771] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.813789] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.815269] scsi host0: ahci-imx <6>[ 3.815629] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.828001] CAN device driver interface <6>[ 3.829315] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.832845] pps pps0: new PPS source ptp0 <6>[ 3.865759] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.867221] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.867227] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.867285] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.867291] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.873280] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.873323] usbcore: registered new interface driver pegasus <6>[ 3.873364] usbcore: registered new interface driver asix <6>[ 3.873400] usbcore: registered new interface driver ax88179_178a <6>[ 3.873432] usbcore: registered new interface driver cdc_ether <6>[ 3.873475] usbcore: registered new interface driver smsc75xx <6>[ 3.873531] usbcore: registered new interface driver smsc95xx <6>[ 3.873565] usbcore: registered new interface driver net1080 <6>[ 3.873601] usbcore: registered new interface driver cdc_subset <6>[ 3.873673] usbcore: registered new interface driver zaurus <6>[ 3.873742] usbcore: registered new interface driver cdc_ncm <6>[ 3.877298] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.877306] ehci-pci: EHCI PCI platform driver <6>[ 3.877345] ehci-platform: EHCI generic platform driver <6>[ 3.877633] ehci-orion: EHCI orion driver <6>[ 3.877850] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.878032] ehci-st: EHCI STMicroelectronics driver <6>[ 3.878214] ehci-exynos: EHCI Exynos driver <6>[ 3.878394] ehci-atmel: EHCI Atmel driver <6>[ 3.878571] tegra-ehci: Tegra EHCI driver <6>[ 3.878782] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.878801] ohci-pci: OHCI PCI platform driver <6>[ 3.878852] ohci-platform: OHCI generic platform driver <6>[ 3.879107] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.879291] ohci-st: OHCI STMicroelectronics driver <6>[ 3.879480] ohci-atmel: OHCI Atmel driver <6>[ 3.880515] usbcore: registered new interface driver usb-storage <6>[ 3.888788] i2c /dev entries driver <6>[ 3.908564] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.908572] sdhci: Copyright(c) Pierre Ossman <6>[ 3.911332] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.913287] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.914602] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.914645] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.915890] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.918467] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.919425] usbcore: registered new interface driver usbhid <6>[ 3.919432] usbhid: USB HID core driver <6>[ 3.926021] NET: Registered protocol family 10 <6>[ 3.927001] Segment Routing with IPv6 <6>[ 3.927077] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.927639] NET: Registered protocol family 17 <6>[ 3.927656] can: controller area network core <6>[ 3.927732] NET: Registered protocol family 29 <6>[ 3.927740] can: raw protocol <6>[ 3.927748] can: broadcast manager protocol <6>[ 3.927758] can: netlink gateway - max_hops=1 <5>[ 3.928185] Key type dns_resolver registered <6>[ 3.930223] ThumbEE CPU extension supported. <5>[ 3.930238] Registering SWP/SWPB emulation handler <6>[ 3.931009] printk: console [ttymxc1]: printing thread started <6>[ 3.931215] printk: console [ramoops-1]: printing thread started <5>[ 3.931242] Loading compiled-in X.509 certificates <6>[ 3.936362] pstore: Using crash dump compression: deflate <6>[ 3.955862] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.956261] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <4>[ 3.958008] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.958147] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.959596] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.967977] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.971516] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.971547] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.993663] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.994285] hub 1-0:1.0: USB hub found <6>[ 3.994318] hub 1-0:1.0: 1 port detected <6>[ 3.996359] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.000595] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.000732] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.002100] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.006494] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.006620] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.007985] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.009837] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.015104] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.015232] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.016627] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.145308] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.145354] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.145361] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.157442] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.185327] mmc2: new high speed SDHC card at address aaaa <6>[ 4.191991] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <4>[ 4.255018] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.255027] GPT:29296874 != 31116287 <4>[ 4.255032] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.255034] GPT:29296874 != 31116287 <4>[ 4.255039] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.255078] mmcblk2: p1 p2 p3 <4>[ 4.274040] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.274171] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.275614] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.303669] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.528975] hub 1-1:1.0: USB hub found <6>[ 4.535356] hub 1-1:1.0: 3 ports detected <4>[ 4.582200] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.582322] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.583733] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.284200] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.313775] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.343792] Sending DHCP requests ., OK <6>[ 7.383821] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 7.383846] IP-Config: Complete: <6>[ 7.383852] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.383877] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 7.383889] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.383905] nameserver0=192.168.201.1 <6>[ 7.392309] Freeing unused kernel memory: 2048K <6>[ 7.454040] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.590551] udevd[139]: starting version 3.2.9 <5>[ 7.591578] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.591826] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.591945] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.600732] udevd[139]: specified user 'tss' unknown <27>[ 7.600879] udevd[139]: specified group 'tss' unknown <30>[ 7.603345] udevd[140]: starting eudev-3.2.9 <6>[ 8.023713] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.037855] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.057636] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.057790] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.059305] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.071463] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.071628] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.071768] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.071901] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.076575] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.076729] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.078222] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.137735] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.137851] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.137967] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.138065] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.168890] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.169041] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.170595] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.234395] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.272972] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.303823] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.303949] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.312249] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.312326] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.312340] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.312806] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.393903] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.393978] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.394050] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.394099] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.399001] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.399156] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.400675] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.453854] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.514657] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.575423] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.575448] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.575456] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.580158] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.580239] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.580305] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.580355] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.617695] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.617908] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.619796] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.625243] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.625314] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.625371] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.625414] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.628134] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.635006] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.685429] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.685616] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.687771] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.718116] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.718187] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.718248] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.718316] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.994458] caam algorithms registered in /proc/crypto <6>[ 8.995943] caam 2100000.crypto: registering rng-caam <4>[ 8.999944] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.000117] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.001924] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.005634] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.005700] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.005773] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.005821] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) done Saving random seed: OK <5>[ 9.091208] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK <5>[ 9.174049] random: dropbear: uninitialized urandom read (32 bytes read) <5>[ 9.178474] random: crng init done <5>[ 9.178483] random: 1 urandom warning(s) missed due to ratelimiting /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9730550/environment . /lava-9730550/environment / # /lava-9730550/bin/lava-test-runner /lava-9730550/0 /lava-9730550/bin/lava-test-runner /lava-9730550/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9730550/0/tests/0_dmesg + cat uuid + UUID=9730550_1.5.2.4.1 + set +x + KERNELCI_LAVA=y<8>[ 9.790788] /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.829548] <8>[ 9.862083] + set +x / # # export SHELL=/bin/sh <8>[ 9.895720] <8>[ 9.897007] # / # export SHELL=/bin/sh. /lava-9730550/environment / # . /lava-9730550/environment/lava-9730550/bin/lava-test-runner /lava-9730550/1 / # /lava-9730550/bin/lava-test-runner /lava-9730550/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9730550/1/tests/1_bootrr + cat uuid + UUID=9730550_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9730550/1/../bin:/sbi<8>[ 10.373723] n:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 120000.hdmi backlight-lcd backlight-lvds /lava-9730550/1/../bin/lava-test-case <8>[ 11.437550] /lava-9730550/1/../bin/lava-test-case <8>[ 11.478217] /lava-9730550/1/../bin/lava-test-case <8>[ 11.502955] + set +x / # <8>[ 11.514835]