[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9730077/tftp-deploy-yclcr1ss/kernel/zImage tftp 0x10000000 9730077/tftp-deploy-yclcr1ss/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9730077/tftp-deploy-yclcr1ss/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 11.7 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 9730077/tftp-deploy-yclcr1ss/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9730077/tftp-deploy-yclcr1ss/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9730077/tftp-deploy-yclcr1ss/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 11.7 MiB/s done Bytes transferred = 12142955 (b9496b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9730077/tftp-deploy-yclcr1ss/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9730077/tftp-deploy-yclcr1ss/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9730077/tftp-deploy-yclcr1ss/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9730077/extract-nfsrootfs-lyt8nkbg,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9730077/extract-nfsrootfs-lyt8nkbg,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12142891 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29-rt12 (KernelCI@build-j1227395-arm-gcc-10-multi-v7-defconfig-82khf) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 12:47:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9730077/extract-nfsrootfs-lyt8nkbg,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936480K/1048576K available (14336K kernel code, 2330K rwdata, 5348K rodata, 2048K init, 415K bss, 46560K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000016] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003795] Console: colour dummy device 80x30 [ 0.003847] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003861] pid_max: default: 32768 minimum: 301 [ 0.004021] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004043] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004678] CPU: Testing write buffer coherency: ok [ 0.004711] CPU0: Spectre v2: using BPIALL workaround [ 0.004957] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005671] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007267] rcu: Hierarchical SRCU implementation. [ 0.010857] EFI services will not be available. [ 0.011162] smp: Bringing up secondary CPUs ... [ 0.011980] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011994] CPU1: Spectre v2: using BPIALL workaround [ 0.012900] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.012914] CPU2: Spectre v2: using BPIALL workaround [ 0.013799] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.013812] CPU3: Spectre v2: using BPIALL workaround [ 0.013927] smp: Brought up 1 node, 4 CPUs [ 0.013937] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.013946] CPU: All CPU(s) started in SVC mode. [ 0.014501] devtmpfs: initialized [ 0.021808] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022042] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022067] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025180] pinctrl core: initialized pinctrl subsystem [ 0.027020] DMI not present or invalid. [ 0.027858] NET: Registered protocol family 16 [ 0.031420] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033732] thermal_sys: Registered thermal governor 'step_wise' [ 0.033912] cpuidle: using governor menu [ 0.034088] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.213183] vdd1p1: supplied by regulator-dummy [ 0.220557] vdd3p0: supplied by regulator-dummy [ 0.227854] vdd2p5: supplied by regulator-dummy [ 0.235189] vddarm: supplied by regulator-dummy [ 0.242661] vddpu: supplied by regulator-dummy [ 0.249835] vddsoc: supplied by regulator-dummy [ 0.586700] No ATAGs? [ 0.586840] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.586850] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.591046] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.597186] Serial: AMBA PL011 UART driver [ 0.599400] printk: console [ramoops-1] enabled [ 0.599608] pstore: Registered ramoops as persistent store backend [ 0.599614] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.631884] iommu: Default domain type: Translated [ 0.632311] vgaarb: loaded [ 0.633217] SCSI subsystem initialized [ 0.633783] usbcore: registered new interface driver usbfs [ 0.633839] usbcore: registered new interface driver hub [ 0.633879] usbcore: registered new device driver usb [ 0.635416] i2c i2c-0: IMX I2C adapter registered [ 0.636746] i2c i2c-1: IMX I2C adapter registered [ 0.637567] i2c i2c-2: IMX I2C adapter registered [ 0.638888] pps_core: LinuxPPS API ver. 1 registered [ 0.638895] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.638919] PTP clock support registered [ 0.642776] clocksource: Switched to clocksource mxc_timer1 [ 1.791805] NET: Registered protocol family 2 [ 1.792231] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.793435] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.793479] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.793568] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.793714] TCP: Hash tables configured (established 8192 bind 8192) [ 1.793924] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.793970] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.794153] NET: Registered protocol family 1 [ 1.794757] RPC: Registered named UNIX socket transport module. [ 1.794765] RPC: Registered udp transport module. [ 1.794770] RPC: Registered tcp transport module. [ 1.794774] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.794785] PCI: CLS 0 bytes, default 64 [ 1.795270] Trying to unpack rootfs image as initramfs... [ 2.758090] Freeing initrd memory: 11860K [ 2.758638] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.759093] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.760936] Initialise system trusted keyrings [ 2.761259] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.767051] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.767777] NFS: Registering the id_resolver key type [ 2.767830] Key type id_resolver registered [ 2.767836] Key type id_legacy registered [ 2.767934] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.767943] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.767976] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.768447] Key type asymmetric registered [ 2.768455] Asymmetric key parser 'x509' registered [ 2.768505] bounce: pool size: 64 pages [ 2.768546] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.768555] io scheduler mq-deadline registered [ 2.768561] io scheduler kyber registered [ 2.808368] mxs-dma 110000.dma-apbh: initialized [ 2.813145] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.813164] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.873103] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.877554] SuperH (H)SCI(F) driver initialized [ 2.878529] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.879534] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 2.879575] printk: console [ttymxc1] enabled [ 2.880995] msm_serial: driver initialized [ 2.881260] STMicroelectronics ASC driver initialized [ 2.883300] STM32 USART driver initialized [ 2.894076] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.894246] panel-simple panel-lcd: Specify missing connector_type [ 2.894624] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.903526] brd: module loaded [ 2.913389] loop: module loaded [ 2.917312] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.917326] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.917335] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.917344] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.917424] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.917592] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.917655] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.920492] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.920521] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.920538] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.922035] scsi host0: ahci-imx [ 2.922397] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 2.934866] CAN device driver interface [ 2.936164] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.939710] pps pps0: new PPS source ptp0 [ 2.958351] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.959836] e1000e: Intel(R) PRO/1000 Network Driver [ 2.959843] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.959899] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.959904] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.966082] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.966129] usbcore: registered new interface driver pegasus [ 2.966169] usbcore: registered new interface driver asix [ 2.966203] usbcore: registered new interface driver ax88179_178a [ 2.966235] usbcore: registered new interface driver cdc_ether [ 2.966277] usbcore: registered new interface driver smsc75xx [ 2.966329] usbcore: registered new interface driver smsc95xx [ 2.966361] usbcore: registered new interface driver net1080 [ 2.966395] usbcore: registered new interface driver cdc_subset [ 2.966423] usbcore: registered new interface driver zaurus [ 2.966490] usbcore: registered new interface driver cdc_ncm [ 2.970042] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.970049] ehci-pci: EHCI PCI platform driver [ 2.970087] ehci-platform: EHCI generic platform driver [ 2.970369] ehci-orion: EHCI orion driver [ 2.970587] SPEAr-ehci: EHCI SPEAr driver [ 2.970771] ehci-st: EHCI STMicroelectronics driver [ 2.970960] ehci-exynos: EHCI Exynos driver [ 2.971142] ehci-atmel: EHCI Atmel driver [ 2.971325] tegra-ehci: Tegra EHCI driver [ 2.971539] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.971559] ohci-pci: OHCI PCI platform driver [ 2.971610] ohci-platform: OHCI generic platform driver [ 2.971871] SPEAr-ohci: OHCI SPEAr driver [ 2.972060] ohci-st: OHCI STMicroelectronics driver [ 2.972247] ohci-atmel: OHCI Atmel driver [ 2.973378] usbcore: registered new interface driver usb-storage [ 2.981562] i2c /dev entries driver [ 3.001397] sdhci: Secure Digital Host Controller Interface driver [ 3.001406] sdhci: Copyright(c) Pierre Ossman [ 3.004188] Synopsys Designware Multimedia Card Interface Driver [ 3.006158] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.007434] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 3.007486] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 3.007680] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 3.011281] ledtrig-cpu: registered to indicate activity on CPUs [ 3.012259] usbcore: registered new interface driver usbhid [ 3.012266] usbhid: USB HID core driver [ 3.018845] NET: Registered protocol family 10 [ 3.019841] Segment Routing with IPv6 [ 3.019925] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.020495] NET: Registered protocol family 17 [ 3.020512] can: controller area network core [ 3.020585] NET: Registered protocol family 29 [ 3.020593] can: raw protocol [ 3.020600] can: broadcast manager protocol [ 3.020611] can: netlink gateway - max_hops=1 [ 3.020998] Key type dns_resolver registered [ 3.023091] ThumbEE CPU extension supported. [ 3.023108] Registering SWP/SWPB emulation handler [ 3.023590] printk: console [ttymxc1]: printing thread started [ 3.023838] printk: console [ramoops-1]: printing thread started [ 3.023893] Loading compiled-in X.509 certificates [ 3.029081] pstore: Using crash dump compression: deflate [ 3.041451] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 3.050205] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.050374] panel-simple panel-lcd: Specify missing connector_type [ 3.051890] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.057400] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 3.060435] imx_usb 2184200.usb: No over current polarity defined [ 3.063969] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.063994] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.092694] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.093284] hub 1-0:1.0: USB hub found [ 3.093321] hub 1-0:1.0: 1 port detected [ 3.095334] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.099543] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.099694] panel-simple panel-lcd: Specify missing connector_type [ 3.101101] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.105424] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.105551] panel-simple panel-lcd: Specify missing connector_type [ 3.106919] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.108901] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.114064] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.114200] panel-simple panel-lcd: Specify missing connector_type [ 3.115674] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.256202] ata1: SATA link down (SStatus 0 SControl 300) [ 3.256249] ahci-imx 2200000.sata: no device found, disabling link. [ 3.256255] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.268079] mmc2: new high speed SDHC card at address 59b4 [ 3.272671] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.274769] mmcblk2: mmc2:59b4 SD 14.7 GiB [ 3.357601] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.357609] GPT:7812499 != 30863359 [ 3.357614] GPT:Alternate GPT header not at the end of the disk. [ 3.357617] GPT:7812499 != 30863359 [ 3.357620] GPT: Use GNU Parted to correct GPT errors. [ 3.357658] mmcblk2: p1 p2 p3 [ 3.372667] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.378689] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.378815] panel-simple panel-lcd: Specify missing connector_type [ 3.380221] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.589121] hub 1-1:1.0: USB hub found [ 3.594119] hub 1-1:1.0: 3 ports detected [ 3.630441] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.630562] panel-simple panel-lcd: Specify missing connector_type [ 3.631909] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.393174] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.412736] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.442733] Sending DHCP requests ., OK [ 6.482757] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 [ 6.482782] IP-Config: Complete: [ 6.482787] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 [ 6.482813] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) [ 6.482826] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.482840] nameserver0=192.168.201.1 [ 6.491337] Freeing unused kernel memory: 2048K [ 6.543674] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.371427] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.373436] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.378495] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.378685] panel-simple panel-lcd: Specify missing connector_type [ 7.380355] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.395122] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.395300] panel-simple panel-lcd: Specify missing connector_type [ 7.397066] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.466766] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.466962] panel-simple panel-lcd: Specify missing connector_type [ 7.468900] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.486121] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.486241] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.486364] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.486466] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.497350] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.497546] panel-simple panel-lcd: Specify missing connector_type [ 7.499471] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.563373] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.564225] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.564563] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.564650] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.575892] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.575974] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.575987] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.583462] caam 2100000.crypto: Entropy delay = 3200 [ 7.644259] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.670613] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.682143] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 7.682298] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 7.682427] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 7.682535] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 7.699872] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.702911] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.705021] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.705040] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.705049] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.716556] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.716627] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.716687] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.716737] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.718598] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.718776] panel-simple panel-lcd: Specify missing connector_type [ 7.720880] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.742447] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.742533] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.742594] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.742684] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.752566] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.752808] panel-simple panel-lcd: Specify missing connector_type [ 7.754684] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.765390] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.765470] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.765530] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.765577] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.153933] caam algorithms registered in /proc/crypto [ 8.155276] caam 2100000.crypto: registering rng-caam [ 8.156966] panel-simple panel-lcd: supply power not found, using dummy regulator Begin: Loading essential drivers [ 8.157180] panel-simple panel-lcd: Specify missing connector_type ... [ 8.159201] panel-simple panel-lvds0: supply power not found, using dummy regulator done. Begin: Running /scripts/init-premount ... done. Begin: M[ 8.166063] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) ounting root file system ... Begi[ 8.166124] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) n: Running /scripts/nfs-top ... [ 8.166187] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done. [ 8.166234] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/nfs-premo[ 8.167580] panel-simple panel-lcd: supply power not found, using dummy regulator unt ... Waiting up to 60 secs for[ 8.167737] panel-simple panel-lcd: Specify missing connector_type any ethernet to become available Device /sys/class/net/eth0 found done. [ 8.337699] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.327866] systemd[1]: System time before build time, advancing clock. [ 9.377413] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.378165] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.455766] systemd[1]: Set hostname to . [ OK ] Created slice[ 10.329438] systemd[1]: Queued start job for default target Graphical Interface. system-getty.slice.[ 10.330912] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.330936] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.331778] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. [ 10.393478] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.424013] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 10.453774] systemd[1]: Created slice User and Session Slice. [ OK ] Started [0;1[ 10.483494] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. ;39mDispatch Password …ts to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.523074] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ 10.553414] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.553713] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Paths. [ 10.583177] systemd[1]: Reached target Paths. [ OK ] Reached target Remote File Systems. [ 10.612917] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. [ 10.625089] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. [ 10.653214] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.683994] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on Journal Socket (/dev/l[ 10.766579] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. og). [ 10.768659] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket. [ 10.813642] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.845384] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ 10.876270] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on [ 10.904260] systemd[1]: Listening on udev Kernel Socket. udev Kernel Socket. Mounting Kernel[ 10.944033] systemd[1]: Condition check resulted in Huge Pages File System being skipped. Debug File System... [ 10.944975] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 10.950993] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Trace File System... [ 10.996497] systemd[1]: Mounting Kernel Trace File System... Starting Create list of st…odes for the curr[ 11.038062] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel... Starting Load K[ 11.099461] systemd[1]: Starting Load Kernel Module configfs... ernel Module configfs... Starting Load Kernel Module drm... [ 11.148301] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... [ 11.177860] systemd[1]: Starting Load Kernel Module fuse... Starting Journa[ 11.207263] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... [ 11.211029] systemd[1]: Starting Journal Service... Starting Load K[ 11.271559] systemd[1]: Starting Load Kernel Modules... ernel Modules... Starting Remount Root and Kernel File Systems[ 11.307087] systemd[1]: Starting Remount Root and Kernel File Systems... [0m... Starting Coldplug All udev Devices... [ 11.356565] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0[ 11.397800] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. [ 11.443397] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.473931] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Started Journal Service. [ 11.523706] systemd[1]: Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 11.835442] systemd-journald[279]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.175-cip29-rt12 #1 SMP Wed Mar 22 12:47:20 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9730077/extract-nfsrootfs-lyt8nkbg' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9730077/extract-nfsrootfs-lyt8nkbg' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9730077/environment . /lava-9730077/environment / # /lava-9730077/bin/lava-test-runner /lava-9730077/0 /lava-9730077/bin/lava-test-runner /lava-9730077/0 + export TESTRUN_ID=0_dmesg + cd /lava-9730077/0/tests/0_dmesg + cat uuid + UUID=9730077_1.6.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 25.537754] [ 25.631773] [ 25.710113] + set +x [ 25.790118] [ 25.791052] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9730077/environment / # . /lava-9730077/environment/lava-9730077/bin/lava-test-runner /lava-9730077/1 / # /lava-9730077/bin/lava-test-runner /lava-9730077/1 + export TESTRUN_ID=1_bootrr + cd /lava-9730077/1/tests/1_bootrr + cat uuid + UUID=9730077_1.6.2.4.5 + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/[ 26.387338] lava-9730077/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi panel-lcd /lava-9730077/1/../bin/lava-test-case [ 27.527386] /lava-9730077/1/../bin/lava-test-case [ 27.595619] /lava-9730077/1/../bin/lava-test-case [ 27.636340] + set +x [ 27.659655] / #