Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3006 device /dev/ttyimx7d-sdb-1 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 23C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => setenv ipaddr 172.16.1.16; setenv serverip 172.16.1.4; setenv ethact FEC0; setenv ethprime FEC setenv ipaddr 172.16.1.16; setenv serverip 172.16.1.4; setenv ethact FEC0; setenv ethprime FEC => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1181729/tftp-deploy-5kwadhep/kernel/zImage tftp 0x80800000 1181729/tftp-deploy-5kwadhep/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1181729/tftp-deploy-5kwadhep/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 1.6 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x86800000 1181729/tftp-deploy-5kwadhep/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1181729/tftp-deploy-5kwadhep/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1181729/tftp-deploy-5kwadhep/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 10.2 MiB/s done Bytes transferred = 16078463 (f5567f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1181729/tftp-deploy-5kwadhep/dtb/imx7d-sdb.dtb tftp 0x83000000 1181729/tftp-deploy-5kwadhep/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.16 Filename '1181729/tftp-deploy-5kwadhep/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 5.2 MiB/s done Bytes transferred = 37996 (946c hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16078399 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300c46b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29-rt12 (KernelCI@build-j1227395-arm-gcc-10-multi-v7-defconfig-82khf) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 12:47:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] pcpu-alloc: s33612 r8192 d23732 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932788K/1048576K available (14336K kernel code, 2330K rwdata, 5348K rodata, 2048K init, 415K bss, 50252K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000001] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008310] Switching to timer-based delay loop, resolution 125ns <6>[ 0.015998] Switching to timer-based delay loop, resolution 41ns <6>[ 0.020998] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029135] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.043588] Console: colour dummy device 80x30 <6>[ 0.045508] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.056149] pid_max: default: 32768 minimum: 301 <6>[ 0.061205] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.068665] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.077463] CPU: Testing write buffer coherency: ok <6>[ 0.082192] CPU0: update cpu_capacity 1024 <6>[ 0.086231] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.092967] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.100491] rcu: Hierarchical SRCU implementation. <6>[ 0.107633] EFI services will not be available. <6>[ 0.109823] smp: Bringing up secondary CPUs ... <6>[ 0.115113] smp: Brought up 1 node, 1 CPU <6>[ 0.118684] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.125205] CPU: All CPU(s) started in SVC mode. <6>[ 0.130626] devtmpfs: initialized <6>[ 0.142013] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.147435] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.157331] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.166823] pinctrl core: initialized pinctrl subsystem <6>[ 0.171906] DMI not present or invalid. <6>[ 0.175090] NET: Registered protocol family 16 <6>[ 0.180945] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.188701] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.188823] cpuidle: using governor menu <6>[ 0.197007] No ATAGs? <6>[ 0.199069] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.207341] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.216454] Serial: AMBA PL011 UART driver <6>[ 0.266996] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <6>[ 0.272774] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.325635] iommu: Default domain type: Translated <6>[ 0.328922] vgaarb: loaded <5>[ 0.332010] SCSI subsystem initialized <7>[ 0.335315] libata version 3.00 loaded. <6>[ 0.339378] usbcore: registered new interface driver usbfs <6>[ 0.344947] usbcore: registered new interface driver hub <6>[ 0.350479] usbcore: registered new device driver usb <6>[ 0.364001] i2c i2c-0: IMX I2C adapter registered <6>[ 0.372128] i2c i2c-1: IMX I2C adapter registered <6>[ 0.374829] i2c i2c-2: IMX I2C adapter registered <6>[ 0.385127] i2c i2c-3: IMX I2C adapter registered <6>[ 0.388620] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.392535] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.401982] PTP clock support registered <6>[ 0.409931] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.526324] NET: Registered protocol family 2 <6>[ 1.528390] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.537045] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.544534] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.552622] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.560117] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.566728] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.573602] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.581088] NET: Registered protocol family 1 <6>[ 1.586327] RPC: Registered named UNIX socket transport module. <6>[ 1.591782] RPC: Registered udp transport module. <6>[ 1.596715] RPC: Registered tcp transport module. <6>[ 1.601718] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.608447] PCI: CLS 0 bytes, default 64 <6>[ 1.613192] Trying to unpack rootfs image as initramfs... <6>[ 2.949517] Freeing initrd memory: 15704K <6>[ 2.951758] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 2.961208] Initialise system trusted keyrings <6>[ 2.964682] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 2.978035] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.982236] NFS: Registering the id_resolver key type <5>[ 2.986779] Key type id_resolver registered <5>[ 2.991138] Key type id_legacy registered <6>[ 2.995513] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.002416] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.010150] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.015274] Key type asymmetric registered <5>[ 3.019108] Asymmetric key parser 'x509' registered <6>[ 3.024355] bounce: pool size: 64 pages <6>[ 3.028421] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.036103] io scheduler mq-deadline registered <6>[ 3.040924] io scheduler kyber registered <4>[ 3.068696] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 3.086468] mxs-dma 33000000.dma-apbh: initialized <4>[ 3.101545] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 3.108596] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 3.171889] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.180361] SuperH (H)SCI(F) driver initialized <3>[ 3.183128] clk: failed to reparent uart1_src to pll_sys_main_240m_clk: -16 <6>[ 3.189846] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 58, base_baud = 1500000) is a IMX <6>[ 3.198823] printk: console [ttymxc0] enabled <6>[ 3.203313] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.198823] printk: console [ttymxc0] enabled <6>[ 3.203313] printk: bootconsole [ec_imx6q0] disabled <6>[ 3.209586] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 67, base_baud = 15000000) is a IMX <6>[ 3.211027] msm_serial: driver initialized <6>[ 3.211277] STMicroelectronics ASC driver initialized <6>[ 3.213003] STM32 USART driver initialized <6>[ 3.232873] brd: module loaded <6>[ 3.240779] loop: module loaded <6>[ 3.256073] CAN device driver interface <6>[ 3.257305] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.262594] pps pps0: new PPS source ptp0 <3>[ 3.263542] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 3.263602] fec 30bf0000.ethernet: Using random MAC address: 0a:a5:07:91:bc:49 <6>[ 4.312687] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 4.314136] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.314145] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.314219] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.314226] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.319690] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.319745] usbcore: registered new interface driver pegasus <6>[ 4.319803] usbcore: registered new interface driver asix <6>[ 4.319851] usbcore: registered new interface driver ax88179_178a <6>[ 4.319983] usbcore: registered new interface driver cdc_ether <6>[ 4.320044] usbcore: registered new interface driver smsc75xx <6>[ 4.320098] usbcore: registered new interface driver smsc95xx <6>[ 4.320139] usbcore: registered new interface driver net1080 <6>[ 4.320179] usbcore: registered new interface driver cdc_subset <6>[ 4.320226] usbcore: registered new interface driver zaurus <6>[ 4.320316] usbcore: registered new interface driver cdc_ncm <6>[ 4.323562] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.323573] ehci-pci: EHCI PCI platform driver <6>[ 4.323617] ehci-platform: EHCI generic platform driver <6>[ 4.323867] ehci-orion: EHCI orion driver <6>[ 4.324061] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.324216] ehci-st: EHCI STMicroelectronics driver <6>[ 4.324368] ehci-exynos: EHCI Exynos driver <6>[ 4.324518] ehci-atmel: EHCI Atmel driver <6>[ 4.324664] tegra-ehci: Tegra EHCI driver <6>[ 4.324850] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.324877] ohci-pci: OHCI PCI platform driver <6>[ 4.324926] ohci-platform: OHCI generic platform driver <6>[ 4.325149] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.325301] ohci-st: OHCI STMicroelectronics driver <6>[ 4.325459] ohci-atmel: OHCI Atmel driver <6>[ 4.326460] usbcore: registered new interface driver usb-storage <6>[ 4.333880] i2c /dev entries driver <3>[ 4.351570] CPUidle arm: CPU 0 failed to init idle CPU ops <6>[ 4.352105] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.352111] sdhci: Copyright(c) Pierre Ossman <6>[ 4.354507] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.356198] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.361176] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO <6>[ 4.361212] sdhci-esdhc-imx 30b40000.mmc: Got WP GPIO <6>[ 4.366466] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.367643] usbcore: registered new interface driver usbhid <6>[ 4.367653] usbhid: USB HID core driver <6>[ 4.374073] NET: Registered protocol family 10 <6>[ 4.375326] Segment Routing with IPv6 <6>[ 4.375410] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.376092] NET: Registered protocol family 17 <6>[ 4.376113] can: controller area network core <6>[ 4.376182] NET: Registered protocol family 29 <6>[ 4.376191] can: raw protocol <6>[ 4.376200] can: broadcast manager protocol <6>[ 4.376212] can: netlink gateway - max_hops=1 <5>[ 4.376734] Key type dns_resolver registered <6>[ 4.376857] ThumbEE CPU extension supported. <5>[ 4.376870] Registering SWP/SWPB emulation handler <6>[ 4.377384] printk: console [ttymxc0]: printing thread started <5>[ 4.377417] Loading compiled-in X.509 certificates <4>[ 4.416394] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.806963] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 4.807660] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA <4>[ 4.811737] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.814232] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.819487] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.867351] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <4>[ 4.870044] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.872505] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.877738] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 4.892205] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.895730] imx_usb 30b10000.usb: No over current polarity defined <4>[ 4.898262] imx_usb 30b20000.usb: No over current polarity defined <4>[ 4.903759] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 4.976812] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 4.980298] IP-Config: Failed to open eth0 <3>[ 4.980314] IP-Config: No network devices available <4>[ 5.008966] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <6>[ 5.021446] Freeing unused kernel memory: 2048K <6>[ 5.021970] Run /init as init process <4>[ 5.022716] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 5.025829] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <6>[ 5.050521] mmc0: new high speed SDHC card at address e624 <6>[ 5.053880] mmcblk0: mmc0:e624 SA16G 14.8 GiB <6>[ 5.056599] mmcblk0: p1 p2 <4>[ 5.063465] imx_usb 30b10000.usb: No over current polarity defined <4>[ 5.066027] imx_usb 30b20000.usb: No over current polarity defined <4>[ 5.071520] pwm-backlight backlight: supply power not found, using dummy regulator Starting syslogd: OK Starting klogd: OK Running sysctl: <6>[ 5.250814] mmc1: new ultra high speed SDR104 SDIO card at address 0001 OK Populating /dev using udev: <30>[ 5.324371] udevd[129]: starting version 3.2.9 <5>[ 5.325421] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.325764] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.325901] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.361369] udevd[129]: specified user 'tss' unknown <27>[ 5.361552] udevd[129]: specified group 'tss' unknown <30>[ 5.371943] udevd[130]: starting eudev-3.2.9 <6>[ 6.960490] gpio-expander@0 enforce active low on chipselect handle <4>[ 7.008415] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 7.008671] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 7.008826] usb_phy_generic usbphynop3: deferred probe timeout, ignoring dependency <4>[ 7.008852] usb_phy_generic: probe of usbphynop3 failed with error -110 <4>[ 7.009093] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 7.009263] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 7.011718] imx_usb 30b10000.usb: No over current polarity defined <4>[ 7.213257] imx_usb 30b20000.usb: No over current polarity defined <6>[ 7.216811] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 7.216864] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 7.259971] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 7.261012] hub 1-0:1.0: USB hub found <6>[ 7.261076] hub 1-0:1.0: 1 port detected <4>[ 7.267434] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 8.551999] caam 30900000.crypto: Entropy delay = 3200 <6>[ 8.611452] caam 30900000.crypto: Instantiated RNG4 SH0 <6>[ 8.670864] caam 30900000.crypto: Instantiated RNG4 SH1 <6>[ 8.670880] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 8.670892] caam 30900000.crypto: job rings = 3, qi = 0 <4>[ 8.755469] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 8.941876] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.295892] pwm-backlight backlight: supply power not found, using dummy regulator <5>[ 9.613673] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 10.174908] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 10.175077] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 10.175097] cfg80211: failed to load regulatory.db <4>[ 10.258043] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 10.289771] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 10.290301] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 10.386002] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 10.936238] caam algorithms registered in /proc/crypto <6>[ 10.937962] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 10.937985] caam 30900000.crypto: registering rng-caam <4>[ 10.967867] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 11.019754] pwm-backlight backlight: supply power not found, using dummy regulator done Saving random seed: OK <5>[ 11.067414] random: dd: uninitialized urandom read (32 bytes read) Starting network: ip: RTNETLINK answers: File exists FAIL <5>[ 11.116698] random: crng init done Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # <3>[ 11.308692] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181729/environment . /lava-1181729/environment / # /lava-1181729/bin/lava-test-runner /lava-1181729/0 /lava-1181729/bin/lava-test-runner /lava-1181729/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1181729/0/tests/0_dmesg + cat uuid + UUID=1181729_1.5.2.4.1 + set +x + KERNELCI_LAVA=y<8>[ 16.995943] /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.043407] <8>[ 17.087200] + set +x / # <8>[ 17.131754] <8>[ 17.133179] # / # export SHELL=/bin/sh. /lava-1181729/environment / # . /lava-1181729/environment/lava-1181729/bin/lava-test-runner /lava-1181729/1 / # /lava-1181729/bin/lava-test-runner /lava-1181729/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1181729/1/tests/1_bootrr + cat uuid + UUID=1181729_1.5.2.4.5 + set +x + export 'PATH=<8>[ 22.875141] /opt/bootrr/libexec/bootrr/helpers:/lava-1181729/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 30730000.lcdif 30360000.anatop:tempmon imx_thermal: failed to register cpufreq cooling device regulator-lcd-3v3 backlight imx-pgc-domain.0 imx-pgc: Failed to get domain's regulator imx-pgc-domain.1 imx-pgc: Failed to get domain's regulator imx-pgc-domain.2 imx-pgc: Failed to get domain's regulator panel 30be0000.ethernet /lava-1181729/1/../bin/lava-test-case <8>[ 23.933859] /lava-1181729/1/../bin/lava-test-case <8>[ 24.978461] /lava-1181729/1/../bin/lava-test-case <8>[ 25.004139] + set +x