connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=52533, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:52533 connected to 192.168.0.1 (port 52533) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.135 U-Boot> setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 2831615/tftp-deploy-on413k4m/kernel/zImage tftp 0x22100000 2831615/tftp-deploy-on413k4m/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '2831615/tftp-deploy-on413k4m/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.4 MiB/s done Bytes transferred = 9671168 (939200 hex) U-Boot> tftp 0x23000000 2831615/tftp-deploy-on413k4m/ramdisk/ramdisk.cpio.gz.uboot tftp 0x23000000 2831615/tftp-deploy-on413k4m/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '2831615/tftp-deploy-on413k4m/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 1.3 MiB/s done Bytes transferred = 16064153 (f51e99 hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 2831615/tftp-deploy-on413k4m/dtb/at91-sama5d4_xplained.dtb tftp 0x22000000 2831615/tftp-deploy-on413k4m/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '2831615/tftp-deploy-on413k4m/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *## 2.6 MiB/s done Bytes transferred = 26763 (688b hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0x939200 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16064089 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200988a Starting kernel ... <6>[ 0.000000] Booting Linux on physical CPU 0x0 <5>[ 0.000000] Linux version 5.10.153-cip19 (KernelCI@build-j478984-arm-gcc-10-multi-v7-defconfig-wtjp6) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Nov 9 10:13:57 UTC 2022 <6>[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d <6>[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache <6>[ 0.000000] OF: fdt: Machine model: Atmel SAMA5D4 Xplained <4>[ 0.000000] Malformed early option 'earlycon' <6>[ 0.000000] Memory policy: Data cache writeback <6>[ 0.000000] efi: UEFI not found. <6>[ 0.000000] cma: Reserved 64 MiB at 0x3c000000 <6>[ 0.000000] Zone ranges: <6>[ 0.000000] DMA [mem 0x0000000020000000-0x000000003fffffff] <6>[ 0.000000] Normal empty <6>[ 0.000000] HighMem empty <6>[ 0.000000] Movable zone start for each node <6>[ 0.000000] Early memory node ranges <6>[ 0.000000] node 0: [mem 0x0000000020000000-0x000000003fffffff] <6>[ 0.000000] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] <6>[ 0.000000] CPU: All CPU(s) started in SVC mode. <6>[ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 <5>[ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 414072K/524288K available (13312K kernel code, 2231K rwdata, 5344K rodata, 2048K init, 424K bss, 44680K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>[ 0.000000] clocksource: timer@fc024000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>[ 0.000019] sched_clock: 32 bits at 11MHz, resolution 90ns, wraps every 195225786322ns <6>[ 0.000053] Switching to timer-based delay loop, resolution 90ns <6>[ 0.000979] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 10859434279 ns <6>[ 0.004423] Console: colour dummy device 80x30 <6>[ 0.004537] Calibrating delay loop (skipped), value calculated using timer frequency.. 22.00 BogoMIPS (lpj=110000) <6>[ 0.004585] pid_max: default: 32768 minimum: 301 <6>[ 0.004930] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.004977] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.006460] CPU: Testing write buffer coherency: ok <6>[ 0.007166] CPU0: thread -1, cpu 0, socket -1, mpidr c0000000 <6>[ 0.008964] Setting up static identity map for 0x20300000 - 0x203000ac <6>[ 0.011252] rcu: Hierarchical SRCU implementation. <6>[ 0.015939] EFI services will not be available. <6>[ 0.016381] smp: Bringing up secondary CPUs ... <6>[ 0.016421] smp: Brought up 1 node, 1 CPU <6>[ 0.016444] SMP: Total of 1 processors activated (22.00 BogoMIPS). <6>[ 0.016462] CPU: All CPU(s) started in SVC mode. <6>[ 0.017509] devtmpfs: initialized <6>[ 0.027829] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.028353] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.028412] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.034079] pinctrl core: initialized pinctrl subsystem <6>[ 0.037523] DMI not present or invalid. <6>[ 0.039360] NET: Registered protocol family 16 <6>[ 0.044347] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.048431] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.048669] cpuidle: using governor menu <6>[ 0.486557] AT91: PM: standby: standby, suspend: ulp0 <6>[ 0.486603] No ATAGs? <6>[ 0.486758] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.486785] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.489219] gpio-at91 fc06a000.gpio: at address (ptrval) <6>[ 0.491101] gpio-at91 fc06b000.gpio: at address (ptrval) <6>[ 0.493013] gpio-at91 fc06c000.gpio: at address (ptrval) <6>[ 0.494541] gpio-at91 fc068000.gpio: at address (ptrval) <6>[ 0.496614] gpio-at91 fc06d000.gpio: at address (ptrval) <6>[ 0.498878] pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>[ 0.508459] Serial: AMBA PL011 UART driver <3>[ 0.509300] atmel_tcb f801c000.timer: IRQ index 1 not found <3>[ 0.509351] atmel_tcb f801c000.timer: IRQ index 2 not found <3>[ 0.509918] atmel_tcb fc020000.timer: IRQ index 1 not found <3>[ 0.509967] atmel_tcb fc020000.timer: IRQ index 2 not found <4>[ 0.510472] atmel_tcb: probe of fc024000.timer failed with error -16 <6>[ 0.547000] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.550256] at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.554051] AT91: Detected SoC family: sama5d4 <6>[ 0.554091] AT91: Detected SoC: sama5d44, revision 0 <6>[ 0.555701] VDD MCI1: supplied by VCC 3V3 <6>[ 0.560605] iommu: Default domain type: Translated <6>[ 0.561818] vgaarb: loaded <5>[ 0.563601] SCSI subsystem initialized <6>[ 0.564858] usbcore: registered new interface driver usbfs <6>[ 0.564990] usbcore: registered new interface driver hub <6>[ 0.565111] usbcore: registered new device driver usb <6>[ 0.567592] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.567629] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.567689] PTP clock support registered <6>[ 0.574156] clocksource: Switched to clocksource timer@fc024000 <6>[ 2.683377] NET: Registered protocol family 2 <6>[ 2.683987] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.685798] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.685904] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.686008] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.686156] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.686427] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.686515] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.686958] NET: Registered protocol family 1 <6>[ 2.688811] RPC: Registered named UNIX socket transport module. <6>[ 2.688857] RPC: Registered udp transport module. <6>[ 2.688877] RPC: Registered tcp transport module. <6>[ 2.688896] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.688924] PCI: CLS 0 bytes, default 64 <6>[ 2.689710] Trying to unpack rootfs image as initramfs... <6>[ 5.202900] Freeing initrd memory: 15688K <5>[ 5.205863] Initialise system trusted keyrings <6>[ 5.206633] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 5.219140] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 5.221023] NFS: Registering the id_resolver key type <5>[ 5.221192] Key type id_resolver registered <5>[ 5.221220] Key type id_legacy registered <6>[ 5.221453] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 5.221484] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 5.221574] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 5.222711] Key type asymmetric registered <5>[ 5.222753] Asymmetric key parser 'x509' registered <6>[ 5.222868] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 5.222896] io scheduler mq-deadline registered <6>[ 5.222916] io scheduler kyber registered <6>[ 5.408898] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 5.416895] SuperH (H)SCI(F) driver initialized <6>[ 5.418870] msm_serial: driver initialized <6>[ 5.419251] STMicroelectronics ASC driver initialized <6>[ 5.421813] STM32 USART driver initialized <6>[ 5.460813] brd: module loaded <6>[ 5.479304] loop: module loaded <4>[ 5.482205] atmel_usart_serial: Failed to locate of_node [id: -2] <6>[ 5.483271] atmel_usart_serial.0.auto: ttyAT5 at MMIO 0xf8004000 (irq = 24, base_baud = 5500000) is a ATMEL_SERIAL <4>[ 5.485787] atmel_usart_serial: Failed to locate of_node [id: -2] <6>[ 5.486812] atmel_usart_serial.1.auto: ttyAT0 at MMIO 0xfc00c000 (irq = 30, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 6.320087] printk: console [ttyAT0] enabled <4>[ 6.326911] atmel_usart_serial: Failed to locate of_node [id: -2] <6>[ 6.334417] atmel_usart_serial.2.auto: ttyAT1 at MMIO 0xfc010000 (irq = 31, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 6.370180] CAN device driver interface <6>[ 6.443840] macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 28 (52:11:6d:6b:d5:8f) <6>[ 6.455315] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.463476] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 6.468787] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 6.475152] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 6.480776] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 6.495287] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 6.503049] usbcore: registered new interface driver pegasus <6>[ 6.509165] usbcore: registered new interface driver asix <6>[ 6.514956] usbcore: registered new interface driver ax88179_178a <6>[ 6.521353] usbcore: registered new interface driver cdc_ether <6>[ 6.527584] usbcore: registered new interface driver smsc75xx <6>[ 6.533666] usbcore: registered new interface driver smsc95xx <6>[ 6.539789] usbcore: registered new interface driver net1080 <6>[ 6.545820] usbcore: registered new interface driver cdc_subset <6>[ 6.552066] usbcore: registered new interface driver zaurus <6>[ 6.558125] usbcore: registered new interface driver cdc_ncm <6>[ 6.569247] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 6.576143] ehci-pci: EHCI PCI platform driver <6>[ 6.580917] ehci-platform: EHCI generic platform driver <6>[ 6.586918] ehci-orion: EHCI orion driver <6>[ 6.591497] SPEAr-ehci: EHCI SPEAr driver <6>[ 6.596125] ehci-st: EHCI STMicroelectronics driver <6>[ 6.601516] ehci-exynos: EHCI Exynos driver <6>[ 6.606299] ehci-atmel: EHCI Atmel driver <6>[ 6.614753] atmel-ehci 600000.ehci: EHCI Host Controller <6>[ 6.620371] atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1 <6>[ 6.629528] atmel-ehci 600000.ehci: irq 19, io mem 0x00600000 <6>[ 6.664195] atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00 <6>[ 6.672212] hub 1-0:1.0: USB hub found <6>[ 6.676502] hub 1-0:1.0: 3 ports detected <6>[ 6.682559] tegra-ehci: Tegra EHCI driver <6>[ 6.687424] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 6.693901] ohci-pci: OHCI PCI platform driver <6>[ 6.698804] ohci-platform: OHCI generic platform driver <6>[ 6.704797] SPEAr-ohci: OHCI SPEAr driver <6>[ 6.709341] ohci-st: OHCI STMicroelectronics driver <6>[ 6.714852] ohci-atmel: OHCI Atmel driver <6>[ 6.720907] at91_ohci 500000.ohci: USB Host Controller <6>[ 6.726479] at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2 <6>[ 6.735965] at91_ohci 500000.ohci: irq 19, io mem 0x00500000 <6>[ 6.810111] hub 2-0:1.0: USB hub found <6>[ 6.814388] hub 2-0:1.0: 3 ports detected <6>[ 6.822432] usbcore: registered new interface driver usb-storage <6>[ 6.840100] i2c /dev entries driver <6>[ 6.854558] at91-reset fc068600.rstc: Starting after wakeup <6>[ 6.872250] sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0) <6>[ 6.890235] sdhci: Secure Digital Host Controller Interface driver <6>[ 6.896770] sdhci: Copyright(c) Pierre Ossman <6>[ 6.905599] Synopsys Designware Multimedia Card Interface Driver <6>[ 6.914895] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 6.929706] atmel_mci fc000000.mmc: version: 0x600 <6>[ 6.935516] atmel_mci fc000000.mmc: using dma0chan0 for DMA transfers <6>[ 6.943477] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 6.951700] usbcore: registered new interface driver usbhid <6>[ 6.957671] usbhid: USB HID core driver <6>[ 6.978050] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc <6>[ 6.984817] nand: Micron MT29F4G08ABAEAWP <6>[ 6.989051] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 <6>[ 6.998200] atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 29, 1 slots <6>[ 7.009773] Bad block table found at page 131008, version 0x01 <6>[ 7.017048] Bad block table found at page 130944, version 0x01 <5>[ 7.023835] 7 fixed-partitions partitions found on MTD device atmel_nand <5>[ 7.030894] Creating 7 MTD partitions on \"atmel_nand\": <5>[ 7.036330] 0x000000000000-0x000000040000 : \"at91bootstrap\" <5>[ 7.045362] 0x000000040000-0x000000100000 : \"bootloader\" <5>[ 7.053960] 0x000000100000-0x000000140000 : \"bootloader env redundant\" <5>[ 7.063939] 0x000000140000-0x000000180000 : \"bootloader env\" <5>[ 7.073131] 0x000000180000-0x000000200000 : \"device tree\" <5>[ 7.081966] 0x000000200000-0x000000800000 : \"kernel\" <5>[ 7.090345] 0x000000800000-0x000020000000 : \"rootfs\" <6>[ 7.108475] NET: Registered protocol family 10 <6>[ 7.116066] Segment Routing with IPv6 <6>[ 7.120121] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.127827] NET: Registered protocol family 17 <6>[ 7.132535] can: controller area network core <6>[ 7.137441] NET: Registered protocol family 29 <6>[ 7.142116] can: raw protocol <6>[ 7.145423] can: broadcast manager protocol <6>[ 7.149847] can: netlink gateway - max_hops=1 <5>[ 7.155397] Key type dns_resolver registered <6>[ 7.160105] ThumbEE CPU extension supported. <5>[ 7.164730] Registering SWP/SWPB emulation handler <5>[ 7.170577] Loading compiled-in X.509 certificates <6>[ 7.196081] input: gpio_keys as /devices/platform/gpio_keys/input/input0 <6>[ 7.287013] macb f8020000.ethernet eth0: PHY [f8020000.ethernet-ffffffff:01] driver [Micrel KSZ8081 or KSZ8091] (irq=46) <6>[ 7.299101] macb f8020000.ethernet eth0: configuring for phy/rmii link mode <6>[ 9.107099] macb f8020000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 9.115414] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 9.144388] Sending DHCP requests ., OK <6>[ 9.188306] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.135 <6>[ 9.196409] IP-Config: Complete: <6>[ 9.199866] device=eth0, hwaddr=52:11:6d:6b:d5:8f, ipaddr=192.168.0.135, mask=255.255.255.0, gw=192.168.0.254 <6>[ 9.210566] host=192.168.0.135, domain=, nis-domain=(none) <6>[ 9.216765] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 9.216778] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 9.232498] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan2 for rx DMA transfers <6>[ 9.241889] atmel_usart_serial atmel_usart_serial.1.auto: using dma0chan3 for tx DMA transfers <6>[ 9.256922] Freeing unused kernel memory: 2048K <6>[ 9.262042] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.678473] udevd[83]: starting version 3.2.9 <5>[ 9.686514] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.693771] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.701774] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.731030] udevd[83]: specified user 'tss' unknown <27>[ 9.737091] udevd[83]: specified group 'tss' unknown <30>[ 9.751643] udevd[84]: starting eudev-3.2.9 <6>[ 13.822113] atmel_spi f8010000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <6>[ 13.831378] m25p80@0 enforce active low on chipselect handle <3>[ 13.965524] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 <6>[ 13.972725] atmel_spi f8010000.spi: Atmel SPI Controller version 0x221 at 0xf8010000 (irq 25) <6>[ 14.115036] atmel_spi fc018000.spi: Using dma0chan6 (tx) and dma0chan7 (rx) for DMA transfers <6>[ 14.194401] atmel_spi fc018000.spi: Atmel SPI Controller version 0x221 at 0xfc018000 (irq 32) <6>[ 14.950887] at91_i2c f8014000.i2c: using dma0chan8 (tx) and dma0chan9 (rx) for DMA transfers <6>[ 15.074789] i2c i2c-0: using pinctrl states for GPIO recovery <6>[ 15.080865] i2c i2c-0: using generic GPIOs for recovery <6>[ 15.086612] at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <6>[ 15.685603] iio iio:device0: Resolution used: 10 bits <6>[ 15.690903] iio iio:device0: ADC Touch screen is disabled. <6>[ 15.835209] atmel_tdes fc04c000.tdes: version: 0x702 <6>[ 15.870897] atmel_aes fc044000.aes: version: 0x201 <6>[ 15.882035] atmel_sha fc050000.sha: version: 0x420 <6>[ 15.905100] atmel_tdes fc04c000.tdes: using dma1chan0, dma1chan1 for DMA transfers <6>[ 15.964628] atmel_sha fc050000.sha: using dma1chan4 for DMA transfers <6>[ 16.035746] atmel_aes fc044000.aes: Atmel AES - Using dma1chan2, dma1chan3 for DMA transfers <6>[ 16.085155] atmel_sha fc050000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 16.104726] atmel_tdes fc04c000.tdes: Atmel DES/TDES <6>[ 16.513147] at91_rtc fc0686b0.rtc: registered as rtc0 <6>[ 16.518684] at91_rtc fc0686b0.rtc: setting system clock to 2012-01-01T00:00:38 UTC (1325376038) <6>[ 16.527696] at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  2  1  0 Rien a faire U-Boot> RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  2  1  0 Rien a faire U-Boot>