Trying 192.168.1.205... Connected to ts5. Escape character is '^]'. ser2net port telnet,2002 device serialdev,/dev/ttyUSB-lf-bbb-02,115200n81,local [] (Debian GNU/Linux) U-Boot SPL 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) Trying to boot from MMC2 U-Boot 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 172.16.3.191 (27 ms) => setenv serverip 172.16.3.3 setenv serverip 172.16.3.3 => tftp 0x82000000 874180/tftp-deploy-q1q1nf07/kernel/zImage tftp 0x82000000 874180/tftp-deploy-q1q1nf07/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.191 Filename '874180/tftp-deploy-q1q1nf07/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 3.9 MiB/s done Bytes transferred = 4603496 (463e68 hex) => tftp 0x83000000 874180/tftp-deploy-q1q1nf07/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 874180/tftp-deploy-q1q1nf07/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.191 Filename '874180/tftp-deploy-q1q1nf07/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 13.5 MiB 3.5 MiB/s done Bytes transferred = 14147134 (d7de3e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 874180/tftp-deploy-q1q1nf07/dtb/am335x-boneblack.dtb tftp 0x88000000 874180/tftp-deploy-q1q1nf07/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.191 Filename '874180/tftp-deploy-q1q1nf07/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 3 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x463e68 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-03-13 12:28:30 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14147070 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.173-cip28 (KernelCI@build-j1168650-arm-gcc-10-omap2plus-defconfig-cgnjz) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Mon Mar 13 11:53:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472052K/522240K available (9216K kernel code, 1027K rwdata, 2172K rodata, 1024K init, 279K bss, 33804K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018566] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030201] Console: colour dummy device 80x30 <3>[ 0.035074] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042132] This ensures that you still see kernel messages. Please <3>[ 0.048857] update your kernel commandline. <6>[ 0.053463] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095546] pid_max: default: 32768 minimum: 301 <6>[ 0.100718] LSM: Security Framework initializing <6>[ 0.105832] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.113647] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.122929] CPU: Testing write buffer coherency: ok <6>[ 0.128295] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.134216] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140702] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147900] rcu: Hierarchical SRCU implementation. <6>[ 0.153707] smp: Bringing up secondary CPUs ... <6>[ 0.158643] smp: Brought up 1 node, 1 CPU <6>[ 0.163091] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169831] CPU: All CPU(s) started in SVC mode. <6>[ 0.175577] devtmpfs: initialized <6>[ 0.191276] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199817] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210251] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218900] pinctrl core: initialized pinctrl subsystem <6>[ 0.226457] NET: Registered protocol family 16 <6>[ 0.234051] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260482] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266570] audit: initializing netlink subsys (disabled) <6>[ 0.273641] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273655] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280266] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.286987] cpuidle: using governor menu <5>[ 1.169025] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.294465] No ATAGs? <6>[ 1.297092] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.321559] Kprobes globally optimized <6>[ 1.334641] iommu: Default domain type: Translated <6>[ 1.342024] vgaarb: loaded <5>[ 1.345616] SCSI subsystem initialized <6>[ 1.350817] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.356202] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.365998] PTP clock support registered <6>[ 1.371606] clocksource: Switched to clocksource dmtimer <5>[ 2.043658] VFS: Disk quotas dquot_6.6.0 <6>[ 2.048069] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.065007] NET: Registered protocol family 2 <6>[ 2.070070] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.078764] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.087719] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.096014] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.103693] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.110617] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.117648] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.125268] NET: Registered protocol family 1 <6>[ 2.131076] RPC: Registered named UNIX socket transport module. <6>[ 2.137537] RPC: Registered udp transport module. <6>[ 2.142667] RPC: Registered tcp transport module. <6>[ 2.147772] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.154700] PCI: CLS 0 bytes, default 64 <6>[ 2.159711] Trying to unpack rootfs image as initramfs... <6>[ 3.151072] Freeing initrd memory: 13816K <6>[ 3.156787] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.167195] Initialise system trusted keyrings <6>[ 3.172660] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.180817] NFS: Registering the id_resolver key type <5>[ 3.186433] Key type id_resolver registered <5>[ 3.191006] Key type id_legacy registered <6>[ 3.195484] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.203472] Key type asymmetric registered <5>[ 3.207965] Asymmetric key parser 'x509' registered <6>[ 3.213313] io scheduler mq-deadline registered <6>[ 3.218244] io scheduler kyber registered <3>[ 3.357085] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.365790] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.474862] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.517063] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.589306] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.598015] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.658018] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.666714] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.684250] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.692930] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.756687] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.765249] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.792423] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.806976] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.817883] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.827325] printk: console [ttyS0] enabled <6>[ 3.827325] printk: console [ttyS0] enabled <6>[ 3.836402] printk: bootconsole [omap8250] disabled <6>[ 3.836402] printk: bootconsole [omap8250] disabled <6>[ 3.860221] brd: module loaded <6>[ 3.872695] loop: module loaded <3>[ 3.878148] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.951590] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.993991] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.003925] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.010577] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.016390] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.023939] cpsw 4a100000.ethernet: Detected MACID = 04:79:b7:e7:06:e0 <6>[ 4.033000] i2c /dev entries driver <5>[ 4.038484] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.046415] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.052961] sdhci: Copyright(c) Pierre Ossman <6>[ 4.058315] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.066639] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.076487] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.084941] Initializing XFRM netlink socket <6>[ 4.089744] NET: Registered protocol family 10 <6>[ 4.096170] Segment Routing with IPv6 <6>[ 4.100232] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.107303] NET: Registered protocol family 17 <6>[ 4.112160] NET: Registered protocol family 15 <5>[ 4.116996] Key type dns_resolver registered <6>[ 4.122201] oprofile: using arm/armv7 <6>[ 4.126242] ThumbEE CPU extension supported. <5>[ 4.130817] Registering SWP/SWPB emulation handler <3>[ 4.136367] omap_voltage_late_init: Voltage driver support not added <3>[ 4.143086] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.151500] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.160167] SmartReflex Class3 initialized <6>[ 4.165288] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.174241] Loading compiled-in X.509 certificates <6>[ 4.199138] OMAP GPIO hardware version 0.1 <4>[ 4.232244] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.245896] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.254710] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.261070] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.271122] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.282548] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.291646] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.296806] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.307187] mmc1: new high speed MMC card at address 0001 <6>[ 4.314183] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.319429] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.326148] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.333605] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.343937] mmcblk1: p1 <6>[ 4.367712] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.377363] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.463101] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 6.602229] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.611573] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.641705] Sending DHCP requests ., OK <6>[ 6.765666] IP-Config: Got DHCP answer from 172.16.3.3, my address is 172.16.3.191 <6>[ 6.773565] IP-Config: Complete: <6>[ 6.777076] device=eth0, hwaddr=04:79:b7:e7:06:e0, ipaddr=172.16.3.191, mask=255.255.255.0, gw=172.16.3.3 <6>[ 6.787402] host=172.16.3.191, domain=denx.de, nis-domain=(none) <6>[ 6.794149] bootserver=172.16.3.33, rootserver=172.16.3.33, rootpath= <6>[ 6.794156] nameserver0=172.16.3.3 <6>[ 6.805449] ntpserver0=172.16.3.3 <6>[ 6.812346] Freeing unused kernel memory: 1024K <6>[ 6.832046] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.066770] udevd[100]: starting version 3.2.9 <5>[ 7.073518] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.080725] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.088364] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.105675] udevd[100]: specified user 'tss' unknown <27>[ 7.111245] udevd[100]: specified group 'tss' unknown <30>[ 7.123755] udevd[101]: starting eudev-3.2.9 <6>[ 7.790219] remoteproc remoteproc0: wkup_m3 is available <4>[ 8.246071] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.255245] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.322116] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 8.330706] usbcore: registered new interface driver usbfs <6>[ 8.336746] usbcore: registered new interface driver hub <6>[ 8.342480] usbcore: registered new device driver usb <4>[ 8.553097] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.562209] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 8.581234] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 8.699137] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 8.706874] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 8.855962] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 8.861796] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 8.918028] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <4>[ 8.929766] at24 2-0055: supply vcc not found, using dummy regulator <3>[ 8.983632] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.002832] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 9.008268] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 9.056538] at24 2-0056: supply vcc not found, using dummy regulator <6>[ 9.064536] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.073219] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.080736] usb usb1: Product: MUSB HDRC host driver <6>[ 9.086011] usb usb1: Manufacturer: Linux 5.10.173-cip28 musb-hcd <6>[ 9.092411] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.099310] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 9.174681] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 9.422451] hub 1-0:1.0: USB hub found <6>[ 9.432601] tda998x 0-0070: found TDA19988 <6>[ 9.508903] hub 1-0:1.0: 1 port detected <3>[ 9.572960] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.972456] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 9.999274] remoteproc remoteproc0: powering up wkup_m3 <3>[ 10.037524] davinci-mcasp 48038000.mcasp: IRQ common not found <4>[ 10.085468] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 10.095415] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 10.101682] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 10.704496] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 10.711704] random: crng init done <6>[ 10.746535] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 10.770185] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 10.882002] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.928921] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 10.987741] PM: Cannot get wkup_m3_ipc handle <6>[ 11.186724] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 11.215265] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 11.265561] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 11.274935] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 11.373682] PM: Cannot get wkup_m3_ipc handle <3>[ 11.404236] PM: Cannot get wkup_m3_ipc handle <3>[ 11.880585] PM: Cannot get wkup_m3_ipc handle <3>[ 11.922704] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-874180/environment . /lava-874180/environment / # /lava-874180/bin/lava-test-runner /lava-874180/0 /lava-874180/bin/lava-test-runner /lava-874180/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-874180/0/tests/0_dmesg + cat uuid + UUID=874180_1.5.2.4.1 <8>[ 12.846746] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.912452] <8>[ 12.972488] <8>[ 13.032625] + set +x <8>[ 13.044221] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-874180/environment / # . /lava-874180/environment/lava-874180/bin/lava-test-runner /lava-874180/1 / # /lava-874180/bin/lava-test-runner /lava-874180/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-874180/1/tests/1_bootrr + cat uuid + UUID=874180_1.5.2.4.5 <8>[ 13.588732] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-874180/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto pm33xx /lava-874180/1/../bin/lava-test-case <8>[ 14.692064] /lava-874180/1/../bin/lava-test-case <8>[ 14.746632] /lava-874180/1/../bin/lava-test-case <8>[ 14.779574] + set +x <8>[ 14.807696] / #