Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3023 device /dev/ttyimx6ul-14x14-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 30C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.160 (1376 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1181480/tftp-deploy-86n5y4z4/kernel/zImage tftp 0x80800000 1181480/tftp-deploy-86n5y4z4/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181480/tftp-deploy-86n5y4z4/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.4 MiB/s done Bytes transferred = 9691648 (93e200 hex) => tftp 0x86800000 1181480/tftp-deploy-86n5y4z4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1181480/tftp-deploy-86n5y4z4/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181480/tftp-deploy-86n5y4z4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 16077171 (f55173 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1181480/tftp-deploy-86n5y4z4/dtb/imx6ul-14x14-evk.dtb tftp 0x83000000 1181480/tftp-deploy-86n5y4z4/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1181480/tftp-deploy-86n5y4z4/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *### 418 KiB/s done Bytes transferred = 30855 (7887 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x93e200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16077107 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300a886 ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29 (KernelCI@build-j1225928-arm-gcc-10-multi-v7-defconfig-b8sqc) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 07:17:42 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 414044K/524288K available (13312K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 44708K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000019] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008103] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.025032] Console: colour dummy device 80x30 <6>[ 0.026993] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.037608] pid_max: default: 32768 minimum: 301 <6>[ 0.042750] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.050024] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.059462] CPU: Testing write buffer coherency: ok <6>[ 0.063762] CPU0: update cpu_capacity 1024 <6>[ 0.067458] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.075184] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.082580] rcu: Hierarchical SRCU implementation. <6>[ 0.090915] EFI services will not be available. <6>[ 0.093305] smp: Bringing up secondary CPUs ... <6>[ 0.097763] smp: Brought up 1 node, 1 CPU <6>[ 0.101938] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.108407] CPU: All CPU(s) started in SVC mode. <6>[ 0.114302] devtmpfs: initialized <6>[ 0.130713] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.136331] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.146080] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.157768] pinctrl core: initialized pinctrl subsystem <6>[ 0.164159] DMI not present or invalid. <6>[ 0.167635] NET: Registered protocol family 16 <6>[ 0.174927] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.184793] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.184985] cpuidle: using governor menu <6>[ 0.435672] vdd3p0: supplied by regulator-dummy <6>[ 0.450523] cpu: supplied by regulator-dummy <6>[ 0.465627] vddsoc: supplied by regulator-dummy <6>[ 0.895634] No ATAGs? <6>[ 0.896767] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.903696] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.918411] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.932756] Serial: AMBA PL011 UART driver <6>[ 1.005759] iommu: Default domain type: Translated <6>[ 1.008930] vgaarb: loaded <5>[ 1.013188] SCSI subsystem initialized <6>[ 1.016439] usbcore: registered new interface driver usbfs <6>[ 1.020897] usbcore: registered new interface driver hub <6>[ 1.026546] usbcore: registered new device driver usb <6>[ 1.035086] i2c i2c-0: IMX I2C adapter registered <6>[ 1.039337] i2c i2c-1: IMX I2C adapter registered <6>[ 1.045008] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.047519] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.056859] PTP clock support registered <6>[ 1.069394] clocksource: Switched to clocksource mxc_timer1 <6>[ 3.323548] NET: Registered protocol family 2 <6>[ 3.325852] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 3.334826] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 3.341587] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 3.349587] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 3.356972] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 3.363711] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.370357] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.377867] NET: Registered protocol family 1 <6>[ 3.383959] RPC: Registered named UNIX socket transport module. <6>[ 3.388243] RPC: Registered udp transport module. <6>[ 3.393338] RPC: Registered tcp transport module. <6>[ 3.398157] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 3.404923] PCI: CLS 0 bytes, default 64 <6>[ 3.410180] Trying to unpack rootfs image as initramfs... <6>[ 6.407645] Freeing initrd memory: 15704K <6>[ 6.410577] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 6.421197] Initialise system trusted keyrings <6>[ 6.423977] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 6.445896] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.451244] NFS: Registering the id_resolver key type <5>[ 6.454646] Key type id_resolver registered <5>[ 6.458912] Key type id_legacy registered <6>[ 6.463569] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.470200] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.477874] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.483708] Key type asymmetric registered <5>[ 6.486756] Asymmetric key parser 'x509' registered <6>[ 6.492083] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.499599] io scheduler mq-deadline registered <6>[ 6.504328] io scheduler kyber registered <4>[ 6.560465] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 6.594285] mxs-dma 1804000.dma-apbh: initialized <4>[ 6.625237] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.632354] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 6.768314] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.782522] SuperH (H)SCI(F) driver 鹥ѥ���镑5 <6>[ 6.786633] printk: console [ttymxc0] enabled <6>[ 6.786633] printk: console [ttymxc0] enabled <6>[ 6.794054] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.794054] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.807099] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 73, base_baud = 5000000) is a IMX <6>[ 6.819641] msm_serial: driver initialized <6>[ 6.824679] STMicroelectronics ASC driver initialized <6>[ 6.834110] STM32 USART driver initialized <4>[ 6.861022] panel-simple panel: supply power not found, using dummy regulator <4>[ 6.868875] panel-simple panel: Specify missing connector_type <6>[ 6.900529] brd: module loaded <6>[ 6.921919] loop: module loaded <6>[ 6.960731] CAN device driver interface <6>[ 6.967576] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.976973] pps pps0: new PPS source ptp0 <6>[ 7.126321] fec 20b4000.ethernet eth0: registered PHC device 0 <6>[ 7.135946] pps pps1: new PPS source ptp1 <6>[ 9.361761] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 9.371049] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 9.376311] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 9.382815] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 9.388502] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 9.407624] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 9.415591] usbcore: registered new interface driver pegasus <6>[ 9.421729] usbcore: registered new interface driver asix <6>[ 9.427519] usbcore: registered new interface driver ax88179_178a <6>[ 9.434052] usbcore: registered new interface driver cdc_ether <6>[ 9.440341] usbcore: registered new interface driver smsc75xx <6>[ 9.446480] usbcore: registered new interface driver smsc95xx <6>[ 9.452662] usbcore: registered new interface driver net1080 <6>[ 9.458689] usbcore: registered new interface driver cdc_subset <6>[ 9.465033] usbcore: registered new interface driver zaurus <6>[ 9.471195] usbcore: registered new interface driver cdc_ncm <6>[ 9.485044] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 9.492025] ehci-pci: EHCI PCI platform driver <6>[ 9.496885] ehci-platform: EHCI generic platform driver <6>[ 9.503187] ehci-orion: EHCI orion driver <6>[ 9.507976] SPEAr-ehci: EHCI SPEAr driver <6>[ 9.512820] ehci-st: EHCI STMicroelectronics driver <6>[ 9.518402] ehci-exynos: EHCI Exynos driver <6>[ 9.523394] ehci-atmel: EHCI Atmel driver <6>[ 9.528093] tegra-ehci: Tegra EHCI driver <6>[ 9.532967] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 9.539565] ohci-pci: OHCI PCI platform driver <6>[ 9.544460] ohci-platform: OHCI generic platform driver <6>[ 9.550706] SPEAr-ohci: OHCI SPEAr driver <6>[ 9.555450] ohci-st: OHCI STMicroelectronics driver <6>[ 9.561190] ohci-atmel: OHCI Atmel driver <6>[ 9.567949] usbcore: registered new interface driver usb-storage <6>[ 9.592938] i2c /dev entries driver <6>[ 9.644528] sdhci: Secure Digital Host Controller Interface driver <6>[ 9.651162] sdhci: Copyright(c) Pierre Ossman <6>[ 9.662203] Synopsys Designware Multimedia Card Interface Driver <6>[ 9.673143] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 9.692112] sdhci-esdhc-imx 2190000.mmc: Got CD GPIO <6>[ 9.703555] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 9.712544] usbcore: registered new interface driver usbhid <6>[ 9.718412] usbhid: USB HID core driver <6>[ 9.738544] NET: Registered protocol family 10 <6>[ 9.746304] Segment Routing with IPv6 <6>[ 9.750580] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 9.758331] NET: Registered protocol family 17 <6>[ 9.763206] can: controller area network core <6>[ 9.768028] NET: Registered protocol family 29 <6>[ 9.772850] can: raw protocol <6>[ 9.776114] can: broadcast manager protocol <6>[ 9.780653] can: netlink gateway - max_hops=1 <5>[ 9.786475] Key type dns_resolver registered <6>[ 9.795295] ThumbEE CPU extension supported. <5>[ 9.800032] Registering SWP/SWPB emulation handler <5>[ 9.807063] Loading compiled-in X.509 certificates <6>[ 9.838334] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <4>[ 9.850246] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 9.863217] panel-simple panel: supply power not found, using dummy regulator <4>[ 9.871127] panel-simple panel: Specify missing connector_type <6>[ 9.877552] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA <4>[ 9.889199] imx_usb 2184000.usb: No over current polarity defined <6>[ 9.912197] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 9.917436] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.952087] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 9.962512] hub 1-0:1.0: USB hub found <6>[ 9.966752] hub 1-0:1.0: 1 port detected <6>[ 9.978223] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 9.999790] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.013045] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.020971] panel-simple panel: Specify missing connector_type <4>[ 10.027251] mmc1: host does not support reading read-only switch, assuming write-enable <4>[ 10.041262] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 10.050747] mmc1: new high speed SDHC card at address aaaa <4>[ 10.060961] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.068675] panel-simple panel: Specify missing connector_type <6>[ 10.075657] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <6>[ 10.092001] mmcblk1: p1 p2 <4>[ 10.101508] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.116116] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.124006] panel-simple panel: Specify missing connector_type <6>[ 10.197652] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <6>[ 10.277753] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 13.362684] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 13.382688] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 13.411911] Sending DHCP requests .., OK <6>[ 16.156423] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.160 <6>[ 16.164524] IP-Config: Complete: <6>[ 16.168082] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.160, mask=255.255.255.0, gw=172.16.1.4 <6>[ 16.178476] host=172.16.1.160, domain=example.org, nis-domain=(none) <6>[ 16.185640] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 16.185666] nameserver0=172.16.1.4 <6>[ 16.211960] Freeing unused kernel memory: 2048K <6>[ 16.222284] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.471641] udevd[126]: starting version 3.2.9 <5>[ 16.478154] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.486439] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.493731] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 16.515004] udevd[126]: specified user 'tss' unknown <27>[ 16.520958] udevd[126]: specified group 'tss' unknown <30>[ 16.532185] udevd[127]: starting eudev-3.2.9 <4>[ 19.701604] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 19.853316] panel-simple panel: supply power not found, using dummy regulator <4>[ 19.861223] panel-simple panel: Specify missing connector_type <6>[ 20.463231] caam 2140000.crypto: RNG4 SH0 was previously instantiated without prediction resistance. Tearing it down <6>[ 20.474234] caam 2140000.crypto: Deinstantiated RNG4 SH0 <6>[ 20.479925] caam 2140000.crypto: Instantiated RNG4 SH0 <6>[ 20.485338] caam 2140000.crypto: RNG4 SH1 was previously instantiated without prediction resistance. Tearing it down <6>[ 20.496179] caam 2140000.crypto: Deinstantiated RNG4 SH1 <6>[ 20.501808] caam 2140000.crypto: Instantiated RNG4 SH1 <6>[ 20.507228] caam 2140000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 20.514142] caam 2140000.crypto: job rings = 3, qi = 0 <4>[ 20.534666] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 20.603304] panel-simple panel: supply power not found, using dummy regulator <4>[ 20.611232] panel-simple panel: Specify missing connector_type <6>[ 21.135605] spi-nor spi4.0: n25q256a (32768 Kbytes) <4>[ 21.198335] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 21.304984] panel-simple panel: supply power not found, using dummy regulator <4>[ 21.312905] panel-simple panel: Specify missing connector_type <6>[ 21.533543] gpio@0 enforce active low on chipselect handle <4>[ 21.604736] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 21.648390] panel-simple panel: supply power not found, using dummy regulator <4>[ 21.656348] panel-simple panel: Specify missing connector_type <6>[ 23.263478] caam algorithms registered in /proc/crypto <6>[ 23.272643] caam 2140000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 23.280485] caam 2140000.crypto: registering rng-caam <4>[ 23.292033] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.307850] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.315812] panel-simple panel: Specify missing connector_type <5>[ 23.325049] random: crng init done <4>[ 23.354041] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.369017] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.377031] panel-simple panel: Specify missing connector_type <4>[ 23.433760] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.448746] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.456689] panel-simple panel: Specify missing connector_type done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181480/environment . /lava-1181480/environment / # /lava-1181480/bin/lava-test-runner /lava-1181480/0 /lava-1181480/bin/lava-test-runner /lava-1181480/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1181480/0/tests/0_dmesg + cat uuid + UUID=1181480_1.5.2.4.1<8>[ 29.496457] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 29.564255] <8>[ 29.625560] <8>[ 29.687270] + set +x <8>[ 29.698566] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-1181480/environment / # . /lava-1181480/environment /lava-1181480/bin/lava-test-runner /lava-1181480/1 / # /lava-1181480/bin/lava-test-runner /lava-1181480/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1181480/1/tests/1_bootrr + cat uuid + UUID=1181480_1.5.2.4.5<8>[ 35.463015] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1181480/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound regulator-can-3v3 backlight-display panel 2090000.flexcan 2094000.flexcan 21c8000.lcdif /lava-1181480/1/../bin/lava-test-case <8>[ 36.569221] /lava-1181480/1/../bin/lava-test-case <8>[ 36.625747] /lava-1181480/1/../bin/lava-test-case <8>[ 36.660405] + set +x <8>[ 36.685998] / #