[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10500438/tftp-deploy-bhwgh2xe/kernel/zImage tftp 0x10000000 10500438/tftp-deploy-bhwgh2xe/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10500438/tftp-deploy-bhwgh2xe/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 10.4 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10500438/tftp-deploy-bhwgh2xe/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10500438/tftp-deploy-bhwgh2xe/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10500438/tftp-deploy-bhwgh2xe/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 16079910 (f55c26 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10500438/tftp-deploy-bhwgh2xe/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10500438/tftp-deploy-bhwgh2xe/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10500438/tftp-deploy-bhwgh2xe/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16079846 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.180-cip33 (KernelCI@build-j1578061-arm-gcc-10-multi-v7-defconfig-zqrdm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun May 28 23:17:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932656K/1048576K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 50384K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022151] Console: colour dummy device 80x30 <6>[ 0.024041] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034454] pid_max: default: 32768 minimum: 301 <6>[ 0.039491] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046907] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055516] CPU: Testing write buffer coherency: ok <6>[ 0.060034] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065577] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071967] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079614] rcu: Hierarchical SRCU implementation. <6>[ 0.086603] EFI services will not be available. <6>[ 0.088836] smp: Bringing up secondary CPUs ... <6>[ 0.094121] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094130] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105471] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105478] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116681] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116689] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127116] smp: Brought up 1 node, 4 CPUs <6>[ 0.131345] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137804] CPU: All CPU(s) started in SVC mode. <6>[ 0.143233] devtmpfs: initialized <6>[ 0.153851] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159193] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169065] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179280] pinctrl core: initialized pinctrl subsystem <6>[ 0.183754] DMI not present or invalid. <6>[ 0.186871] NET: Registered protocol family 16 <6>[ 0.194109] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200750] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200941] cpuidle: using governor menu <6>[ 0.209026] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.389516] vdd1p1: supplied by regulator-dummy <6>[ 0.398697] vdd3p0: supplied by regulator-dummy <6>[ 0.407828] vdd2p5: supplied by regulator-dummy <6>[ 0.416969] vddarm: supplied by regulator-dummy <6>[ 0.426264] vddpu: supplied by regulator-dummy <6>[ 0.435185] vddsoc: supplied by regulator-dummy <6>[ 0.766819] No ATAGs? <6>[ 0.767005] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.774761] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.784975] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.795304] Serial: AMBA PL011 UART driver <6>[ 0.799541] printk: console [ramoops-1] enabled <6>[ 0.801797] pstore: Registered ramoops as persistent store backend <6>[ 0.808062] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.845958] iommu: Default domain type: Translated <6>[ 0.848676] vgaarb: loaded <5>[ 0.852090] SCSI subsystem initialized <6>[ 0.855807] usbcore: registered new interface driver usbfs <6>[ 0.861003] usbcore: registered new interface driver hub <6>[ 0.866594] usbcore: registered new device driver usb <6>[ 0.873364] i2c i2c-0: IMX I2C adapter registered <6>[ 0.878192] i2c i2c-1: IMX I2C adapter registered <6>[ 0.882571] i2c i2c-2: IMX I2C adapter registered <6>[ 0.888075] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.891924] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.901357] PTP clock support registered <6>[ 0.909116] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.980195] NET: Registered protocol family 2 <6>[ 1.982400] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.990810] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.998270] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.006339] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.013798] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.020497] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.027155] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.034637] NET: Registered protocol family 1 <6>[ 2.039666] RPC: Registered named UNIX socket transport module. <6>[ 2.045216] RPC: Registered udp transport module. <6>[ 2.050211] RPC: Registered tcp transport module. <6>[ 2.055131] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.061859] PCI: CLS 0 bytes, default 64 <6>[ 2.066522] Trying to unpack rootfs image as initramfs... <6>[ 3.421174] Freeing initrd memory: 15704K <4>[ 3.423137] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.430405] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.440239] Initialise system trusted keyrings <6>[ 3.443421] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.455760] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.459775] NFS: Registering the id_resolver key type <5>[ 3.464372] Key type id_resolver registered <5>[ 3.468750] Key type id_legacy registered <6>[ 3.473137] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.479994] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.487656] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.492751] Key type asymmetric registered <5>[ 3.496593] Asymmetric key parser 'x509' registered <6>[ 3.501790] bounce: pool size: 64 pages <6>[ 3.505842] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.513488] io scheduler mq-deadline registered <6>[ 3.518254] io scheduler kyber registered <6>[ 3.562407] mxs-dma 110000.dma-apbh: initialized <4>[ 3.569158] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.576067] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.643334] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.651580] SuperH (H)SCI(F) driver initialized <6>[ 3.654515] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.663428] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.671327] printk: console [ttymxc1] enabled <6>[ 3.671327] printk: console [ttymxc1] enabled <6>[ 3.680497] printk: bootconsole [ec_imx21] disabled <6>[ 3.680497] printk: bootconsole [ec_imx21] disabled <6>[ 3.692198] msm_serial: driver initialized <6>[ 3.698199] STMicroelectronics ASC driver initialized <6>[ 3.705548] STM32 USART driver initialized <4>[ 3.721104] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.729003] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.735843] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.752689] brd: module loaded <6>[ 3.766007] loop: module loaded <6>[ 3.773440] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.781670] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.789985] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.798435] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.806455] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.814214] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.821787] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.832424] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.839707] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.848769] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.859603] scsi host0: ahci-imx <6>[ 3.863471] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.884153] CAN device driver interface <6>[ 3.889631] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.899172] pps pps0: new PPS source ptp0 <6>[ 3.935953] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.943580] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.948815] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.955083] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.960766] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.972874] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.980606] usbcore: registered new interface driver pegasus <6>[ 3.986582] usbcore: registered new interface driver asix <6>[ 3.992300] usbcore: registered new interface driver ax88179_178a <6>[ 3.998696] usbcore: registered new interface driver cdc_ether <6>[ 4.004857] usbcore: registered new interface driver smsc75xx <6>[ 4.010933] usbcore: registered new interface driver smsc95xx <6>[ 4.016979] usbcore: registered new interface driver net1080 <6>[ 4.022956] usbcore: registered new interface driver cdc_subset <6>[ 4.029201] usbcore: registered new interface driver zaurus <6>[ 4.035109] usbcore: registered new interface driver cdc_ncm <6>[ 4.044651] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.051469] ehci-pci: EHCI PCI platform driver <6>[ 4.056218] ehci-platform: EHCI generic platform driver <6>[ 4.062046] ehci-orion: EHCI orion driver <6>[ 4.066544] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.071028] ehci-st: EHCI STMicroelectronics driver <6>[ 4.076358] ehci-exynos: EHCI Exynos driver <6>[ 4.081010] ehci-atmel: EHCI Atmel driver <6>[ 4.085463] tegra-ehci: Tegra EHCI driver <6>[ 4.089983] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.096448] ohci-pci: OHCI PCI platform driver <6>[ 4.101218] ohci-platform: OHCI generic platform driver <6>[ 4.106977] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.111471] ohci-st: OHCI STMicroelectronics driver <6>[ 4.116805] ohci-atmel: OHCI Atmel driver <6>[ 4.122202] usbcore: registered new interface driver usb-storage <6>[ 4.136727] i2c /dev entries driver <6>[ 4.160448] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.166901] sdhci: Copyright(c) Pierre Ossman <6>[ 4.174293] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.182581] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.189826] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.194075] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.195103] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.205863] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.210588] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.213234] usbcore: registered new interface driver usbhid <6>[ 4.217847] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.223668] usbhid: USB HID core driver <6>[ 4.230210] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.237133] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.240989] NET: Registered protocol family 10 <6>[ 4.242004] Segment Routing with IPv6 <6>[ 4.244397] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.264786] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.271576] NET: Registered protocol family 17 <6>[ 4.276298] can: controller area network core <6>[ 4.281027] NET: Registered protocol family 29 <6>[ 4.285740] can: raw protocol <6>[ 4.288978] can: broadcast manager protocol <6>[ 4.293460] can: netlink gateway - max_hops=1 <5>[ 4.298520] Key type dns_resolver registered <6>[ 4.305139] ThumbEE CPU extension supported. <5>[ 4.309722] Registering SWP/SWPB emulation handler <5>[ 4.315133] Loading compiled-in X.509 certificates <6>[ 4.325355] pstore: Using crash dump compression: deflate <4>[ 4.353138] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.361060] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.369113] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.385539] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.395445] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.400650] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.417556] mmc2: new high speed SDHC card at address aaaa <6>[ 4.424223] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <6>[ 4.429117] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.435715] hub 1-0:1.0: USB hub found <6>[ 4.439896] hub 1-0:1.0: 1 port detected <6>[ 4.446835] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.463550] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.471525] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.479904] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.488947] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.493237] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.496671] GPT:29296874 != 31116287 <4>[ 4.504540] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.508232] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.516385] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.520968] GPT:29296874 != 31116287 <4>[ 4.520971] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.521021] mmcblk2: p1 p2 p3 <6>[ 4.535474] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.550712] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.558598] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.566592] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.582943] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.789133] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.990880] hub 1-1:1.0: USB hub found <6>[ 4.995092] hub 1-1:1.0: 3 ports detected <4>[ 5.003214] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.011365] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.021414] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.679586] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.699214] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.729238] Sending DHCP requests ., OK <6>[ 7.773304] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 7.781653] IP-Config: Complete: <6>[ 7.785175] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.795936] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 7.804084] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.804098] nameserver0=192.168.201.1 <6>[ 7.822869] Freeing unused kernel memory: 2048K <6>[ 7.850121] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.974950] udevd[129]: starting version 3.2.9 <5>[ 7.980598] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.987523] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.994406] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.008105] udevd[129]: specified user 'tss' unknown <27>[ 8.013604] udevd[129]: specified group 'tss' unknown <30>[ 8.021203] udevd[130]: starting eudev-3.2.9 <6>[ 8.311305] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.318165] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.331213] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.339262] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.361320] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.378988] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.387012] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.413168] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.487266] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.495248] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.514863] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.579348] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 8.589593] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.597559] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.614311] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.619272] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.659975] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.666793] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.709323] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.716607] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.733286] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.739709] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.769368] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 8.779913] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.782813] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.787847] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.801802] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.810463] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.819026] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.827640] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.842167] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.843573] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.855539] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <4>[ 8.856257] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.862465] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.875853] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.948124] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.964106] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.972769] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.981203] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.981402] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.991911] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.997729] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.006377] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 9.023005] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 9.072027] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.080145] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.093901] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.102456] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 9.111268] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.112227] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 9.119957] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.136213] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.144870] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.168756] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.176741] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.187596] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.203103] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.211738] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.220321] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.228846] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.372539] caam algorithms registered in /proc/crypto <6>[ 9.379411] caam 2100000.crypto: registering rng-caam <4>[ 9.386404] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.394956] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.404102] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.418158] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.426679] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.435243] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done<6>[ 9.443782] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Saving random seed: <4>[ 9.465778] panel-simple panel-lcd: supply power not found, using dummy regulator <5>[ 9.466203] random: dd: uninitialized urandom read (32 bytes read) <4>[ 9.473752] panel-simple panel-lcd: Specify missing connector_type OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 9.567188] random: crng init done <5>[ 9.571001] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10500438/environment . /lava-10500438/environment / # /lava-10500438/bin/lava-test-runner /lava-10500438/0 /lava-10500438/bin/lava-test-runner /lava-10500438/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10500438/0/tests/0_dmesg + cat uuid + UUID=10500438_1.5.2<8>[ 10.180868] .4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.227058] <8>[ 10.268086] <8>[ 10.308840] + set<8>[ 10.318719] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10500438/environment / # . /lava-10500438/environment/lava-10500438/bin/lava-test-runner /lava-10500438/1 / # /lava-10500438/bin/lava-test-runner /lava-10500438/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10500438/1/tests/1_bootrr <8>[ 10.821205] + cat uuid + UUID=10500438_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10500438/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd 120000.hdmi backlight-lvds panel-lcd /lava-10500438/1/../bin/lava-test-case <8>[ 11.901847] /lava-10500438/1/../bin/lava-test-case <8>[ 11.941241] /lava-10500438/1/../bin/lava-test-case <8>[ 11.966092] + set<8>[ 11.985103] +x / #