[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.13 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10500440/tftp-deploy-5hda4a8t/kernel/zImage tftp 0x10000000 10500440/tftp-deploy-5hda4a8t/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10500440/tftp-deploy-5hda4a8t/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 2.9 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10500440/tftp-deploy-5hda4a8t/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10500440/tftp-deploy-5hda4a8t/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10500440/tftp-deploy-5hda4a8t/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 4.2 MiB/s done Bytes transferred = 12145054 (b9519e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10500440/tftp-deploy-5hda4a8t/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10500440/tftp-deploy-5hda4a8t/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.13 Filename '10500440/tftp-deploy-5hda4a8t/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10500440/extract-nfsrootfs-pqjkezso,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10500440/extract-nfsrootfs-pqjkezso,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12144990 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.180-cip33 (KernelCI@build-j1578061-arm-gcc-10-multi-v7-defconfig-zqrdm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun May 28 23:17:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10500440/extract-nfsrootfs-pqjkezso,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936496K/1048576K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 46544K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 15ns [ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns [ 0.000024] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns [ 0.003814] Console: colour dummy device 80x30 [ 0.003867] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) [ 0.003885] pid_max: default: 32768 minimum: 301 [ 0.004064] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004088] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004723] CPU: Testing write buffer coherency: ok [ 0.004762] CPU0: Spectre v2: using BPIALL workaround [ 0.005018] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005727] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007318] rcu: Hierarchical SRCU implementation. [ 0.010899] EFI services will not be available. [ 0.011210] smp: Bringing up secondary CPUs ... [ 0.012022] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012031] CPU1: Spectre v2: using BPIALL workaround [ 0.012956] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.012964] CPU2: Spectre v2: using BPIALL workaround [ 0.013869] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.013877] CPU3: Spectre v2: using BPIALL workaround [ 0.014001] smp: Brought up 1 node, 4 CPUs [ 0.014016] SMP: Total of 4 processors activated (528.00 BogoMIPS). [ 0.014026] CPU: All CPU(s) started in SVC mode. [ 0.014594] devtmpfs: initialized [ 0.022341] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022575] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022599] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025723] pinctrl core: initialized pinctrl subsystem [ 0.027576] DMI not present or invalid. [ 0.028424] NET: Registered protocol family 16 [ 0.031939] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034273] thermal_sys: Registered thermal governor 'step_wise' [ 0.034464] cpuidle: using governor menu [ 0.034648] CPU identified as i.MX6Q, silicon rev 1.0 [ 0.210231] vdd1p1: supplied by regulator-dummy [ 0.217461] vdd3p0: supplied by regulator-dummy [ 0.224680] vdd2p5: supplied by regulator-dummy [ 0.231902] vddarm: supplied by regulator-dummy [ 0.239258] vddpu: supplied by regulator-dummy [ 0.246296] vddsoc: supplied by regulator-dummy [ 0.576114] No ATAGs? [ 0.576271] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.576283] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.580440] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.586566] Serial: AMBA PL011 UART driver [ 0.589260] printk: console [ramoops-1] enabled [ 0.589479] pstore: Registered ramoops as persistent store backend [ 0.589495] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.622012] iommu: Default domain type: Translated [ 0.622445] vgaarb: loaded [ 0.623354] SCSI subsystem initialized [ 0.623935] usbcore: registered new interface driver usbfs [ 0.623999] usbcore: registered new interface driver hub [ 0.624053] usbcore: registered new device driver usb [ 0.625596] i2c i2c-0: IMX I2C adapter registered [ 0.626952] i2c i2c-1: IMX I2C adapter registered [ 0.627776] i2c i2c-2: IMX I2C adapter registered [ 0.629190] pps_core: LinuxPPS API ver. 1 registered [ 0.629205] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.629236] PTP clock support registered [ 0.633088] clocksource: Switched to clocksource mxc_timer1 [ 1.690879] NET: Registered protocol family 2 [ 1.691324] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.692494] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.692540] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.692635] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.692787] TCP: Hash tables configured (established 8192 bind 8192) [ 1.693087] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.693139] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.693330] NET: Registered protocol family 1 [ 1.693944] RPC: Registered named UNIX socket transport module. [ 1.693960] RPC: Registered udp transport module. [ 1.693970] RPC: Registered tcp transport module. [ 1.693981] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.693998] PCI: CLS 0 bytes, default 64 [ 1.694484] Trying to unpack rootfs image as initramfs... [ 2.655771] Freeing initrd memory: 11864K [ 2.656268] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.656624] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.658484] Initialise system trusted keyrings [ 2.658809] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.664809] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.665535] NFS: Registering the id_resolver key type [ 2.665608] Key type id_resolver registered [ 2.665620] Key type id_legacy registered [ 2.665730] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.665745] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.665787] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.666303] Key type asymmetric registered [ 2.666321] Asymmetric key parser 'x509' registered [ 2.666379] bounce: pool size: 64 pages [ 2.666424] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.666439] io scheduler mq-deadline registered [ 2.666452] io scheduler kyber registered [ 2.706531] mxs-dma 110000.dma-apbh: initialized [ 2.711332] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.711357] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.772263] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.776857] SuperH (H)SCI(F) driver initialized [ 2.777857] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.778903] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 3.607099] printk: console [ttymxc1] enabled [ 3.612875] msm_serial: driver initialized [ 3.617291] STMicroelectronics ASC driver initialized [ 3.624382] STM32 USART driver initialized [ 3.639496] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.647157] panel-simple panel-lcd: Specify missing connector_type [ 3.653697] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.670228] brd: module loaded [ 3.683339] loop: module loaded [ 3.690486] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 3.698446] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 3.706472] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 3.714676] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 3.722415] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 3.729925] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 3.737233] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 3.747551] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.754581] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.763402] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.773980] scsi host0: ahci-imx [ 3.777592] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 3.798047] CAN device driver interface [ 3.803284] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.812536] pps pps0: new PPS source ptp0 [ 3.834947] fec 2188000.ethernet eth0: registered PHC device 0 [ 3.842297] e1000e: Intel(R) PRO/1000 Network Driver [ 3.847304] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.853305] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.858711] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.870482] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.877952] usbcore: registered new interface driver pegasus [ 3.883674] usbcore: registered new interface driver asix [ 3.889113] usbcore: registered new interface driver ax88179_178a [ 3.895264] usbcore: registered new interface driver cdc_ether [ 3.901148] usbcore: registered new interface driver smsc75xx [ 3.906971] usbcore: registered new interface driver smsc95xx [ 3.912758] usbcore: registered new interface driver net1080 [ 3.918476] usbcore: registered new interface driver cdc_subset [ 3.924449] usbcore: registered new interface driver zaurus [ 3.930095] usbcore: registered new interface driver cdc_ncm [ 3.939369] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.945927] ehci-pci: EHCI PCI platform driver [ 3.950415] ehci-platform: EHCI generic platform driver [ 3.955955] ehci-orion: EHCI orion driver [ 3.960191] SPEAr-ehci: EHCI SPEAr driver [ 3.964439] ehci-st: EHCI STMicroelectronics driver [ 3.969511] ehci-exynos: EHCI Exynos driver [ 3.973903] ehci-atmel: EHCI Atmel driver [ 3.978095] tegra-ehci: Tegra EHCI driver [ 3.982321] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.988542] ohci-pci: OHCI PCI platform driver [ 3.993055] ohci-platform: OHCI generic platform driver [ 3.998549] SPEAr-ohci: OHCI SPEAr driver [ 4.002748] ohci-st: OHCI STMicroelectronics driver [ 4.007842] ohci-atmel: OHCI Atmel driver [ 4.012932] usbcore: registered new interface driver usb-storage [ 4.027237] i2c /dev entries driver [ 4.050523] sdhci: Secure Digital Host Controller Interface driver [ 4.056734] sdhci: Copyright(c) Pierre Ossman [ 4.063860] Synopsys Designware Multimedia Card Interface Driver [ 4.071836] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.078828] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 4.083085] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 4.083888] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 4.094113] ledtrig-cpu: registered to indicate activity on CPUs [ 4.101217] usbcore: registered new interface driver usbhid [ 4.106822] usbhid: USB HID core driver [ 4.117288] NET: Registered protocol family 10 [ 4.122705] Segment Routing with IPv6 [ 4.124645] ata1: SATA link down (SStatus 0 SControl 300) [ 4.126483] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.131836] ahci-imx 2200000.sata: no device found, disabling link. [ 4.138296] NET: Registered protocol family 17 [ 4.144029] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 4.144302] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 4.144377] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 4.148496] can: controller area network core [ 4.173887] NET: Registered protocol family 29 [ 4.178342] can: raw protocol [ 4.181320] can: broadcast manager protocol [ 4.185535] can: netlink gateway - max_hops=1 [ 4.190324] Key type dns_resolver registered [ 4.190810] mmc2: new high speed SDHC card at address 0001 [ 4.196375] ThumbEE CPU extension supported. [ 4.201005] mmcblk2: mmc2:0001 SD 14.8 GiB [ 4.204434] Registering SWP/SWPB emulation handler [ 4.213803] Loading compiled-in X.509 certificates [ 4.224417] pstore: Using crash dump compression: deflate [ 4.226069] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.237325] GPT:29296874 != 30965759 [ 4.240912] GPT:Alternate GPT header not at the end of the disk. [ 4.246964] GPT:29296874 != 30965759 [ 4.250553] GPT: Use GNU Parted to correct GPT errors. [ 4.255206] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.255771] mmcblk2: p1 p2 p3 [ 4.263360] panel-simple panel-lcd: Specify missing connector_type [ 4.274402] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.291581] imx_usb 2184200.usb: No over current polarity defined [ 4.301340] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.306289] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.342980] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.349750] hub 1-0:1.0: USB hub found [ 4.353636] hub 1-0:1.0: 1 port detected [ 4.361476] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data [ 4.368846] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem [ 4.376976] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 [ 4.388834] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.396515] panel-simple panel-lcd: Specify missing connector_type [ 4.404451] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.417196] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.424882] panel-simple panel-lcd: Specify missing connector_type [ 4.432736] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.443013] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.455737] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.463434] panel-simple panel-lcd: Specify missing connector_type [ 4.471354] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.484952] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) [ 4.693048] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.894655] hub 1-1:1.0: USB hub found [ 4.898638] hub 1-1:1.0: 3 ports detected [ 4.912910] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.920816] panel-simple panel-lcd: Specify missing connector_type [ 4.930379] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.553549] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 6.573089] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.603040] Sending DHCP requests ., OK [ 6.646959] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.13 [ 6.655037] IP-Config: Complete: [ 6.658297] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.201.13, mask=255.255.255.0, gw=192.168.201.1 [ 6.668800] host=imx6q-sabrelite-lava-cbg-2, domain=lava-rack, nis-domain=(none) [ 6.676690] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.676701] nameserver0=192.168.201.1 [ 6.695191] Freeing unused kernel memory: 2048K [ 6.724010] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.759760] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.772148] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.779981] panel-simple panel-lcd: Specify missing connector_type [ 7.787411] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.795868] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.818393] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.826184] panel-simple panel-lcd: Specify missing connector_type [ 7.837105] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.855239] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.863655] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.872053] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.880452] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.885891] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.896402] panel-simple panel-lcd: Specify missing connector_type [ 7.923409] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.980343] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.989355] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 8.010265] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 8.012030] caam 2100000.crypto: Entropy delay = 3200 [ 8.016913] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 8.071836] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 8.082717] caam 2100000.crypto: Instantiated RNG4 SH0 [ 8.109462] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 8.111472] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 8.117360] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 8.133199] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 8.141030] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 8.143476] caam 2100000.crypto: Instantiated RNG4 SH1 [ 8.154387] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 8.161017] caam 2100000.crypto: job rings = 2, qi = 0 [ 8.182370] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 8.191085] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 8.197270] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 8.205877] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 8.214191] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.222468] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.230794] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.239114] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.250633] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.258654] panel-simple panel-lcd: Specify missing connector_type [ 8.279711] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.311976] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.320340] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.328756] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.337070] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.623403] caam algorithms registered in /proc/crypto [ 8.630125] caam 2100000.crypto: registering rng-caam [ 8.639187] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.647091] panel-simple panel-lcd: Specify missing connector_type [ 8.657668] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.673632] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.681871] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.690150] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.698469] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Ru[ 8.719174] panel-simple panel-lcd: supply power not found, using dummy regulator nning /scripts/nfs-top ... done. [ 8.728427] panel-simple panel-lcd: Specify missing connector_type Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 8.817715] random: crng init done IP-Config: eth0 hardware address 00:19:b8:00:e5:47 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.13 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-2 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.970180] systemd[1]: System time before build time, advancing clock. [ 10.057415] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.081221] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.126070] systemd[1]: Set hostname to . [ 11.030383] systemd[1]: Queued start job for default target Graphical Interface. [ 11.039425] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.051868] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.061358] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.094437] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.134382] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.174081] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.213807] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.253815] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.293686] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.306003] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.343892] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.373498] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.413314] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.443545] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 11.474405] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 11.555138] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 11.566649] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 11.604627] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 11.645534] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 11.686907] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 11.724490] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 11.764261] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 11.773538] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.788282] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 11.830861] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 11.877898] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 11.921377] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 11.956788] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 11.996640] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.037413] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.053542] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.092013] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.128712] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.167578] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.208916] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 12.244409] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 12.284393] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 12.348922] systemd[1]: modprobe@configfs.service: Succeeded. [ 12.355603] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 12.394682] systemd[1]: modprobe@drm.service: Succeeded. [ 12.400927] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 12.433785] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 12.691112] systemd-journald[265]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started Network Name Resolution. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.180-cip33 #1 SMP Sun May 28 23:17:23 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10500440/extract-nfsrootfs-pqjkezso' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10500440/extract-nfsrootfs-pqjkezso' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10500440/environment . /lava-10500440/environment / # /lava-10500440/bin/lava-test-runner /lava-10500440/0 /lava-10500440/bin/lava-test-runner /lava-10500440/0 + export TESTRUN_ID=0_dmesg + cd /lava-10500440/0/tests/0_dmesg + cat uuid + UUID=10500440_1.6.2.4.1[ 29.311359] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 29.455454] [ 29.561444] [ 29.679871] + set[ 29.689262] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10500440/environment / # . /lava-10500440/environment/lava-10500440/bin/lava-test-runner /lava-10500440/1 / # /lava-10500440/bin/lava-test-runner /lava-10500440/1 + export TESTRUN_ID=1_bootrr + cd /lava-10500440/1/tests/1_bootrr + cat uuid + UUID=10500440_1.6.2.4.5[ 30.303252] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10500440/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi panel-lcd /lava-10500440/1/../bin/lava-test-case [ 31.457753] /lava-10500440/1/../bin/lava-test-case [ 31.561993] /lava-10500440/1/../bin/lava-test-case [ 31.618286] + set[ 31.658906] +x / #