Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.9 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 982563/tftp-deploy-3wqyugge/kernel/zImage tftp 0x82000000 982563/tftp-deploy-3wqyugge/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '982563/tftp-deploy-3wqyugge/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.2 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x83000000 982563/tftp-deploy-3wqyugge/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 982563/tftp-deploy-3wqyugge/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '982563/tftp-deploy-3wqyugge/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 16075405 (f54a8d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 982563/tftp-deploy-3wqyugge/dtb/am335x-boneblack.dtb tftp 0x88000000 982563/tftp-deploy-3wqyugge/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.9 Filename '982563/tftp-deploy-3wqyugge/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-07-06 3:47:42 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16075341 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip36 (KernelCI@build-j134673-arm-gcc-10-multi-v7-defconfig-hj7nw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jul 6 03:01:05 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 410848K/522240K available (14336K kernel code, 2239K rwdata, 5356K rodata, 2048K init, 424K bss, 45856K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008337] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019076] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033214] Console: colour dummy device 80x30 <3>[ 0.038081] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045123] This ensures that you still see kernel messages. Please <3>[ 0.051841] update your kernel commandline. <6>[ 0.056446] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096044] pid_max: default: 32768 minimum: 301 <6>[ 0.101251] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.109043] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.118053] CPU: Testing write buffer coherency: ok <6>[ 0.123440] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.129231] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135531] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144730] rcu: Hierarchical SRCU implementation. <6>[ 0.154649] EFI services will not be available. <6>[ 0.159828] smp: Bringing up secondary CPUs ... <6>[ 0.164759] smp: Brought up 1 node, 1 CPU <6>[ 0.169147] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.175882] CPU: All CPU(s) started in SVC mode. <6>[ 0.181503] devtmpfs: initialized <6>[ 0.195981] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.204510] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214940] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.226105] pinctrl core: initialized pinctrl subsystem <6>[ 0.234464] DMI not present or invalid. <6>[ 0.239516] NET: Registered protocol family 16 <6>[ 0.246811] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.273424] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.281637] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281837] cpuidle: using governor menu <6>[ 1.368538] No ATAGs? <6>[ 1.371213] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.385783] Serial: AMBA PL011 UART driver <6>[ 1.424451] iommu: Default domain type: Translated <6>[ 1.430294] vgaarb: loaded <5>[ 1.434324] SCSI subsystem initialized <6>[ 1.439099] usbcore: registered new interface driver usbfs <6>[ 1.445181] usbcore: registered new interface driver hub <6>[ 1.450983] usbcore: registered new device driver usb <6>[ 1.458271] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.463706] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.473399] PTP clock support registered <6>[ 1.481798] clocksource: Switched to clocksource dmtimer <6>[ 2.452891] NET: Registered protocol family 2 <6>[ 2.457925] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.466455] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.475387] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.483672] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.491328] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.498249] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.505272] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.512866] NET: Registered protocol family 1 <6>[ 2.518450] RPC: Registered named UNIX socket transport module. <6>[ 2.524889] RPC: Registered udp transport module. <6>[ 2.529992] RPC: Registered tcp transport module. <6>[ 2.535114] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.542030] PCI: CLS 0 bytes, default 64 <6>[ 2.547024] Trying to unpack rootfs image as initramfs... <6>[ 3.611716] Freeing initrd memory: 15700K <6>[ 3.617135] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.627486] Initialise system trusted keyrings <6>[ 3.632856] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.645951] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.653282] NFS: Registering the id_resolver key type <5>[ 3.658807] Key type id_resolver registered <5>[ 3.663436] Key type id_legacy registered <6>[ 3.667947] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.675158] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.683085] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.688417] Key type asymmetric registered <5>[ 3.692953] Asymmetric key parser 'x509' registered <6>[ 3.698288] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.706185] io scheduler mq-deadline registered <6>[ 3.711110] io scheduler kyber registered <3>[ 3.868243] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.876948] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.999095] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.045233] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.124909] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.133604] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.200037] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.208735] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.227553] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.236246] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.306158] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.314708] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.357127] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.460239] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.472699] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.482085] printk: console [ttyS0] enabled <6>[ 4.482085] printk: console [ttyS0] enabled <6>[ 4.491109] printk: bootconsole [omap8250] disabled <6>[ 4.491109] printk: bootconsole [omap8250] disabled <6>[ 4.504948] SuperH (H)SCI(F) driver initialized <6>[ 4.511946] msm_serial: driver initialized <6>[ 4.516787] STMicroelectronics ASC driver initialized <6>[ 4.524971] STM32 USART driver initialized <6>[ 4.532371] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.551854] random: crng init done <6>[ 4.565282] brd: module loaded <6>[ 4.576350] loop: module loaded <6>[ 4.601308] CAN device driver interface <6>[ 4.607491] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.615792] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.621051] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.627434] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.633154] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.701834] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.738481] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.748407] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.755112] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.760944] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.770088] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.778014] usbcore: registered new interface driver pegasus <6>[ 4.784056] usbcore: registered new interface driver asix <6>[ 4.789775] usbcore: registered new interface driver ax88179_178a <6>[ 4.796220] usbcore: registered new interface driver cdc_ether <6>[ 4.802414] usbcore: registered new interface driver smsc75xx <6>[ 4.808486] usbcore: registered new interface driver smsc95xx <6>[ 4.814590] usbcore: registered new interface driver net1080 <6>[ 4.820567] usbcore: registered new interface driver cdc_subset <6>[ 4.826824] usbcore: registered new interface driver zaurus <6>[ 4.832766] usbcore: registered new interface driver cdc_ncm <6>[ 4.844299] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.851136] ehci-pci: EHCI PCI platform driver <6>[ 4.855980] ehci-platform: EHCI generic platform driver <6>[ 4.862022] ehci-orion: EHCI orion driver <6>[ 4.866677] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.871256] ehci-st: EHCI STMicroelectronics driver <6>[ 4.876793] ehci-exynos: EHCI Exynos driver <6>[ 4.881548] ehci-atmel: EHCI Atmel driver <6>[ 4.886201] tegra-ehci: Tegra EHCI driver <6>[ 4.890826] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.897401] ohci-pci: OHCI PCI platform driver <6>[ 4.902232] ohci-platform: OHCI generic platform driver <6>[ 4.908191] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.912866] ohci-st: OHCI STMicroelectronics driver <6>[ 4.918333] ohci-atmel: OHCI Atmel driver <6>[ 4.924622] usbcore: registered new interface driver usb-storage <6>[ 4.941481] i2c /dev entries driver <5>[ 4.973427] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.981612] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.988190] sdhci: Copyright(c) Pierre Ossman <6>[ 4.997127] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.006489] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 5.021119] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.080989] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.090501] usbcore: registered new interface driver usbhid <6>[ 5.096493] usbhid: USB HID core driver <6>[ 5.109971] NET: Registered protocol family 10 <6>[ 5.116262] Segment Routing with IPv6 <6>[ 5.120294] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.127333] NET: Registered protocol family 17 <6>[ 5.132139] can: controller area network core <6>[ 5.136864] NET: Registered protocol family 29 <6>[ 5.141592] can: raw protocol <6>[ 5.144893] can: broadcast manager protocol <6>[ 5.149364] can: netlink gateway - max_hops=1 <5>[ 5.154797] Key type dns_resolver registered <6>[ 5.159493] ThumbEE CPU extension supported. <5>[ 5.164137] Registering SWP/SWPB emulation handler <3>[ 5.169644] omap_voltage_late_init: Voltage driver support not added <6>[ 5.177877] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 5.186770] Loading compiled-in X.509 certificates <6>[ 5.208148] OMAP GPIO hardware version 0.1 <4>[ 5.242381] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 5.255679] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 5.270844] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 5.277210] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 5.284616] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 5.292607] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 5.302568] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 5.312314] mmc1: new high speed MMC card at address 0001 <6>[ 5.318893] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.324142] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.330672] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.337313] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.346825] mmcblk1: p1 <4>[ 5.350963] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.385778] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.425333] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.463888] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.487460] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.496642] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.501789] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.589696] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.631715] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.723321] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.912693] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.921942] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.951955] Sending DHCP requests ., OK <6>[ 8.996060] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.9 <6>[ 9.004219] IP-Config: Complete: <6>[ 9.007763] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.9, mask=255.255.255.0, gw=192.168.11.1 <6>[ 9.018351] host=192.168.11.9, domain=usen.ad.jp, nis-domain=(none) <6>[ 9.025419] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 9.025440] nameserver0=192.168.11.1 <6>[ 9.049386] Freeing unused kernel memory: 2048K <6>[ 9.073026] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.274828] udevd[97]: starting version 3.2.9 <27>[ 9.291124] udevd[97]: specified user 'tss' unknown <27>[ 9.296934] udevd[97]: specified group 'tss' unknown <30>[ 9.313841] udevd[98]: starting eudev-3.2.9 <4>[ 11.037449] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.046586] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 11.213187] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.222276] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 11.444531] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 11.450188] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.693035] hub 1-0:1.0: USB hub found <6>[ 11.712055] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-982563/environment . /lava-982563/environment / # /lava-982563/bin/lava-test-runner /lava-982563/0 /lava-982563/bin/lava-test-runner /lava-982563/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-982563/0/tests/0_dmesg + cat uuid + UUID=982563_1.5.2.4.1 + <8>[ 16.479585] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.537394] <8>[ 16.589468] <8>[ 16.641478] + set +x <8>[ 16.652974] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-982563/environment / # . /lava-982563/environment/lava-982563/bin/lava-test-runner /lava-982563/1 / # /lava-982563/bin/lava-test-runner /lava-982563/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-982563/1/tests/1_bootrr + cat uuid + UUID=982563_1.5.2.4.5 + <8>[ 17.177608] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-982563/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-982563/1/../bin/lava-test-case <8>[ 18.269822] /lava-982563/1/../bin/lava-test-case <8>[ 18.319390] /lava-982563/1/../bin/lava-test-case <8>[ 18.349167] /lava-982563/1/../bin/lava-test-case <8>[ 18.405040] /lava-982563/1/../bin/lava-test-case <8>[ 18.451209] /lava-982563/1/../bin/lava-test-case <8>[ 18.488213] /lava-982563/1/../bin/lava-test-case <8>[ 18.534765] /lava-982563/1/../bin/lava-test-case <8>[ 18.579379] /lava-982563/1/../bin/lava-test-case <8>[ 18.616203] /lava-982563/1/../bin/lava-test-case <8>[ 18.662222] /lava-982563/1/../bin/lava-test-case <8>[ 19.722360] /lava-982563/1/../bin/lava-test-case <8>[ 20.787946] /lava-982563/1/../bin/lava-test-case <8>[ 20.824608] /lava-982563/1/../bin/lava-test-case <8>[ 20.860484] /lava-982563/1/../bin/lava-test-case <8>[ 20.897971] /lava-982563/1/../bin/lava-test-case <8>[ 20.942933] /lava-982563/1/../bin/lava-test-case <8>[ 20.980599] /lava-982563/1/../bin/lava-test-case <8>[ 21.027344] /lava-982563/1/../bin/lava-test-case <8>[ 21.072705] /lava-982563/1/../bin/lava-test-case <8>[ 21.109351] /lava-982563/1/../bin/lava-test-case <8>[ 21.156141] /lava-982563/1/../bin/lava-test-case <8>[ 21.201645] /lava-982563/1/../bin/lava-test-case <8>[ 21.239361] /lava-982563/1/../bin/lava-test-case <8>[ 21.286065] /lava-982563/1/../bin/lava-test-case <8>[ 21.323454] /lava-982563/1/../bin/lava-test-case <8>[ 21.369259] /lava-982563/1/../bin/lava-test-case <8>[ 22.430569] /lava-982563/1/../bin/lava-test-case <8>[ 23.498168] /lava-982563/1/../bin/lava-test-case <8>[ 23.535854] /lava-982563/1/../bin/lava-test-case <8>[ 23.582373] /lava-982563/1/../bin/lava-test-case <8>[ 23.619852] /lava-982563/1/../bin/lava-test-case <8>[ 23.665922] /lava-982563/1/../bin/lava-test-case <8>[ 24.729133] /lava-982563/1/../bin/lava-test-case <8>[ 25.790195] /lava-982563/1/../bin/lava-test-case <8>[ 25.827408] /lava-982563/1/../bin/lava-test-case <8>[ 25.873665] /lava-982563/1/../bin/lava-test-case <8>[ 26.937529] /lava-982563/1/../bin/lava-test-case <8>[ 28.000313] /lava-982563/1/../bin/lava-test-case <8>[ 29.061531] /lava-982563/1/../bin/lava-test-case <8>[ 30.127515] /lava-982563/1/../bin/lava-test-case <8>[ 31.189411] /lava-982563/1/../bin/lava-test-case <8>[ 32.250538] /lava-982563/1/../bin/lava-test-case <8>[ 33.311092] /lava-982563/1/../bin/lava-test-case <8>[ 34.372236] /lava-982563/1/../bin/lava-test-case <8>[ 35.432245] /lava-982563/1/../bin/lava-test-case <8>[ 36.497523] /lava-982563/1/../bin/lava-test-case <8>[ 37.559617] /lava-982563/1/../bin/lava-test-case <8>[ 38.620906] /lava-982563/1/../bin/lava-test-case <8>[ 39.681662] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-982563/1/../bin/lava-test-case <8>[ 39.720304] /lava-982563/1/../bin/lava-test-case <8>[ 40.790440] /lava-982563/1/../bin/lava-test-case <8>[ 41.850201] + set +x <8>[ 41.865773] / #