[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Couldn't find partition mmc 0:1 Error selecting device File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (10 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11025642/tftp-deploy-qp4opzzy/kernel/zImage tftp 0x10000000 11025642/tftp-deploy-qp4opzzy/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11025642/tftp-deploy-qp4opzzy/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 11.1 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 11025642/tftp-deploy-qp4opzzy/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11025642/tftp-deploy-qp4opzzy/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11025642/tftp-deploy-qp4opzzy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 10.6 MiB/s done Bytes transferred = 12150023 (b96507 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11025642/tftp-deploy-qp4opzzy/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11025642/tftp-deploy-qp4opzzy/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '11025642/tftp-deploy-qp4opzzy/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11025642/extract-nfsrootfs-f6ekk1a8,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11025642/extract-nfsrootfs-f6ekk1a8,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12149959 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip36 (KernelCI@build-j134673-arm-gcc-10-multi-v7-defconfig-hj7nw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jul 6 03:01:05 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11025642/extract-nfsrootfs-f6ekk1a8,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936492K/1048576K available (14336K kernel code, 2239K rwdata, 5356K rodata, 2048K init, 424K bss, 46548K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008442] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022278] Console: colour dummy device 80x30 <6>[ 0.024173] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034581] pid_max: default: 32768 minimum: 301 <6>[ 0.039618] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047034] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055658] CPU: Testing write buffer coherency: ok <6>[ 0.060148] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065712] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072077] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079777] rcu: Hierarchical SRCU implementation. <6>[ 0.086778] EFI services will not be available. <6>[ 0.089010] smp: Bringing up secondary CPUs ... <6>[ 0.094308] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094317] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105656] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105663] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116855] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116863] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127292] smp: Brought up 1 node, 4 CPUs <6>[ 0.131522] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137975] CPU: All CPU(s) started in SVC mode. <6>[ 0.143399] devtmpfs: initialized <6>[ 0.153902] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159233] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169112] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179336] pinctrl core: initialized pinctrl subsystem <6>[ 0.183785] DMI not present or invalid. <6>[ 0.186924] NET: Registered protocol family 16 <6>[ 0.194206] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200875] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201075] cpuidle: using governor menu <6>[ 0.209140] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.386989] vdd1p1: supplied by regulator-dummy <6>[ 0.396054] vdd3p0: supplied by regulator-dummy <6>[ 0.405032] vdd2p5: supplied by regulator-dummy <6>[ 0.414042] vddarm: supplied by regulator-dummy <6>[ 0.423234] vddpu: supplied by regulator-dummy <6>[ 0.432028] vddsoc: supplied by regulator-dummy <6>[ 0.759436] No ATAGs? <6>[ 0.759622] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.767400] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.777563] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.787787] Serial: AMBA PL011 UART driver <6>[ 0.791944] printk: console [ramoops-1] enabled <6>[ 0.794290] pstore: Registered ramoops as persistent store backend <6>[ 0.800547] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.838302] iommu: Default domain type: Translated <6>[ 0.841011] vgaarb: loaded <5>[ 0.844452] SCSI subsystem initialized <6>[ 0.848204] usbcore: registered new interface driver usbfs <6>[ 0.853344] usbcore: registered new interface driver hub <6>[ 0.858928] usbcore: registered new device driver usb <6>[ 0.865748] i2c i2c-0: IMX I2C adapter registered <6>[ 0.870479] i2c i2c-1: IMX I2C adapter registered <6>[ 0.874907] i2c i2c-2: IMX I2C adapter registered <6>[ 0.880430] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.884268] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.893702] PTP clock support registered <6>[ 0.901422] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.963265] NET: Registered protocol family 2 <6>[ 1.965481] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.973883] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.981339] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.989413] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.996855] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.003560] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.010227] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.017712] NET: Registered protocol family 1 <6>[ 2.022755] RPC: Registered named UNIX socket transport module. <6>[ 2.028287] RPC: Registered udp transport module. <6>[ 2.033277] RPC: Registered tcp transport module. <6>[ 2.038203] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.044930] PCI: CLS 0 bytes, default 64 <6>[ 2.049612] Trying to unpack rootfs image as initramfs... <6>[ 3.012094] Freeing initrd memory: 11868K <4>[ 3.013950] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.021249] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.031151] Initialise system trusted keyrings <6>[ 3.034282] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.046558] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.050532] NFS: Registering the id_resolver key type <5>[ 3.055189] Key type id_resolver registered <5>[ 3.059550] Key type id_legacy registered <6>[ 3.063927] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.070775] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.078476] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.083558] Key type asymmetric registered <5>[ 3.087392] Asymmetric key parser 'x509' registered <6>[ 3.092594] bounce: pool size: 64 pages <6>[ 3.096645] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.104287] io scheduler mq-deadline registered <6>[ 3.109055] io scheduler kyber registered <6>[ 3.152746] mxs-dma 110000.dma-apbh: initialized <4>[ 3.159505] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.166449] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.218878] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.227018] SuperH (H)SCI(F) driver initialized <6>[ 3.229972] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.238856] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.246762] printk: console [ttymxc1] enabled <6>[ 3.246762] printk: console [ttymxc1] enabled <6>[ 3.255940] printk: bootconsole [ec_imx21] disabled <6>[ 3.255940] printk: bootconsole [ec_imx21] disabled <6>[ 3.267738] msm_serial: driver initialized <6>[ 3.273683] STMicroelectronics ASC driver initialized <6>[ 3.280965] STM32 USART driver initialized <4>[ 3.295767] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.303698] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.310505] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.327275] brd: module loaded <6>[ 3.340527] loop: module loaded <6>[ 3.347910] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.356141] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.364446] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.372915] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.380921] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.388680] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.396254] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.406864] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.414143] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.423221] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.434054] scsi host0: ahci-imx <6>[ 3.437915] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.458449] CAN device driver interface <6>[ 3.463903] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.473397] pps pps0: new PPS source ptp0 <6>[ 3.495637] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.503265] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.508501] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.514770] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.520438] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.532415] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.540117] usbcore: registered new interface driver pegasus <6>[ 3.546119] usbcore: registered new interface driver asix <6>[ 3.551840] usbcore: registered new interface driver ax88179_178a <6>[ 3.558235] usbcore: registered new interface driver cdc_ether <6>[ 3.564396] usbcore: registered new interface driver smsc75xx <6>[ 3.570452] usbcore: registered new interface driver smsc95xx <6>[ 3.576516] usbcore: registered new interface driver net1080 <6>[ 3.582511] usbcore: registered new interface driver cdc_subset <6>[ 3.588730] usbcore: registered new interface driver zaurus <6>[ 3.594653] usbcore: registered new interface driver cdc_ncm <6>[ 3.604166] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.610965] ehci-pci: EHCI PCI platform driver <6>[ 3.615742] ehci-platform: EHCI generic platform driver <6>[ 3.621549] ehci-orion: EHCI orion driver <6>[ 3.626044] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.630503] ehci-st: EHCI STMicroelectronics driver <6>[ 3.635854] ehci-exynos: EHCI Exynos driver <6>[ 3.640481] ehci-atmel: EHCI Atmel driver <6>[ 3.644962] tegra-ehci: Tegra EHCI driver <6>[ 3.649454] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.655938] ohci-pci: OHCI PCI platform driver <6>[ 3.660691] ohci-platform: OHCI generic platform driver <6>[ 3.666459] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.670927] ohci-st: OHCI STMicroelectronics driver <6>[ 3.676296] ohci-atmel: OHCI Atmel driver <6>[ 3.681883] usbcore: registered new interface driver usb-storage <6>[ 3.696343] i2c /dev entries driver <6>[ 3.719709] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.726189] sdhci: Copyright(c) Pierre Ossman <6>[ 3.733589] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.741837] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.749066] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.753289] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.754370] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.765056] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.772419] usbcore: registered new interface driver usbhid <6>[ 3.778261] usbhid: USB HID core driver <6>[ 3.782899] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.788608] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.788916] NET: Registered protocol family 10 <6>[ 3.795174] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.796389] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.796659] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.800925] Segment Routing with IPv6 <6>[ 3.825641] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.832415] NET: Registered protocol family 17 <6>[ 3.837137] can: controller area network core <6>[ 3.841857] NET: Registered protocol family 29 <6>[ 3.846571] can: raw protocol <6>[ 3.849811] can: broadcast manager protocol <6>[ 3.854291] can: netlink gateway - max_hops=1 <5>[ 3.859354] Key type dns_resolver registered <6>[ 3.865986] ThumbEE CPU extension supported. <5>[ 3.870537] Registering SWP/SWPB emulation handler <5>[ 3.876241] Loading compiled-in X.509 certificates <6>[ 3.886902] pstore: Using crash dump compression: deflate <4>[ 3.914299] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.922234] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.930215] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.942984] mmc2: new high speed SDHC card at address 59b4 <4>[ 3.948688] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.950226] mmcblk2: mmc2:59b4 SD 14.7 GiB <6>[ 3.959476] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.965250] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 3.977845] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.985534] GPT:29296874 != 30863359 <4>[ 3.989375] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.995659] GPT:29296874 != 30863359 <4>[ 3.999498] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.001402] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.004958] mmcblk2: p1 p2 p3 <6>[ 4.014283] hub 1-0:1.0: USB hub found <6>[ 4.018337] hub 1-0:1.0: 1 port detected <6>[ 4.024765] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.040086] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.048002] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.055923] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.068021] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.075929] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.083817] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.093821] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.105680] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.113621] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.121603] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.135338] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.351468] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.553090] hub 1-1:1.0: USB hub found <6>[ 4.557321] hub 1-1:1.0: 3 ports detected <4>[ 4.571793] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.579883] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.589731] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.281928] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.291481] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.321558] Sending DHCP requests ., OK <6>[ 7.365626] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 7.373972] IP-Config: Complete: <6>[ 7.377495] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.388252] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 7.396399] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.396414] nameserver0=192.168.201.1 <6>[ 7.415099] Freeing unused kernel memory: 2048K <6>[ 7.452413] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.299685] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.327244] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.335293] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.345446] imx-ipuv3 2800000.ipu: IPUv3H probed <6>[ 8.361264] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.363629] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.369975] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.386344] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.393423] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.394956] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.402724] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.424331] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.497079] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.504419] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.504797] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.516858] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.523693] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.570525] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.631286] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.636711] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.643609] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.672456] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.686906] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.693348] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.709999] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.731758] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.739651] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.740302] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.748378] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.756742] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.765362] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.773730] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.773785] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.778181] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.781779] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 8.814378] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.822375] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.833869] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.861012] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.869591] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.878137] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.886661] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.145988] caam algorithms registered in /proc/crypto <6>[ 9.152943] caam 2100000.crypto: registering rng-caam <4>[ 9.159872] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.167833] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.185011] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.199765] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers <6>[ 9.208313] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ... <6>[ 9.219599] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done.<6>[ 9.228375] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-pr<4>[ 9.238918] panel-simple panel-lcd: supply power not found, using dummy regulator emount ... done. Begin: Mounting<4>[ 9.248017] panel-simple panel-lcd: Specify missing connector_type root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 9.340747] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.104330] systemd[1]: System time before build time, advancing clock. <30>[ 10.155224] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.179340] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.223700] systemd[1]: Set hostname to . <30>[ 11.096730] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.106412] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.119605] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.129281] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.162851] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.202153] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.242500] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.282201] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.321814] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.362114] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.374900] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.412346] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.441892] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.481550] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.511997] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.542622] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.616635] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.627046] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.663003] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.704173] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.745921] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.782212] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.822733] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.832199] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.844646] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.887696] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.926057] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.965330] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.005179] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.045175] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.086023] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.099199] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.139889] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.175168] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.214758] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.267725] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.312169] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.352662] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.420408] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 12.722917] systemd-journald[273]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Finished Permit User Sessions. [ OK ] Started User Login Management. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.184-cip36 #1 SMP Thu Jul 6 03:01:05 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11025642/extract-nfsrootfs-f6ekk1a8' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11025642/extract-nfsrootfs-f6ekk1a8' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11025642/environment . /lava-11025642/environment / # /lava-11025642/bin/lava-test-runner /lava-11025642/0 /lava-11025642/bin/lava-test-runner /lava-11025642/0 + export TESTRUN_ID=0_dmesg + cd /lava-11025642/0/tests/0_dmesg + cat uuid + UUID=11025642_1.6.2.4.1<8>[ 26.462904] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 26.572552] <8>[ 26.659936] <8>[ 26.751182] + set<8>[ 26.760785] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11025642/environment / # . /lava-11025642/environment/lava-11025642/bin/lava-test-runner /lava-11025642/1 / # /lava-11025642/bin/lava-test-runner /lava-11025642/1 + export TESTRUN_ID=1_bootrr + cd /lava-11025642/1/tests/1_bootrr + cat uuid + UUID=11025642_1.6.2.4.5<8>[ 27.350795] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11025642/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds disp0 panel-lcd /lava-11025642/1/../bin/lava-test-case <8>[ 28.522947] /lava-11025642/1/../bin/lava-test-case <8>[ 28.593580] /lava-11025642/1/../bin/lava-test-case <8>[ 28.640684] + set +x<8>[ 28.673923] / #