[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11330349/tftp-deploy-rhkfrl86/kernel/zImage tftp 0x10000000 11330349/tftp-deploy-rhkfrl86/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11330349/tftp-deploy-rhkfrl86/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 3.6 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 11330349/tftp-deploy-rhkfrl86/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11330349/tftp-deploy-rhkfrl86/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11330349/tftp-deploy-rhkfrl86/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 4.2 MiB/s done Bytes transferred = 16077482 (f552aa hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11330349/tftp-deploy-rhkfrl86/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11330349/tftp-deploy-rhkfrl86/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11330349/tftp-deploy-rhkfrl86/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.2 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16077418 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.186-cip37 (KernelCI@build-j17252-arm-gcc-10-multi-v7-defconfig-8smdh) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Aug 22 11:45:27 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932656K/1048576K available (14336K kernel code, 2239K rwdata, 5356K rodata, 2048K init, 424K bss, 50384K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000007] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008095] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.021716] Console: colour dummy device 80x30 <6>[ 0.023607] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.034280] pid_max: default: 32768 minimum: 301 <6>[ 0.039316] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046734] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055341] CPU: Testing write buffer coherency: ok <6>[ 0.059863] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065401] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071803] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079470] rcu: Hierarchical SRCU implementation. <6>[ 0.086452] EFI services will not be available. <6>[ 0.088691] smp: Bringing up secondary CPUs ... <6>[ 0.093993] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094001] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105326] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105335] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116531] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116538] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.126968] smp: Brought up 1 node, 4 CPUs <6>[ 0.131195] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.137739] CPU: All CPU(s) started in SVC mode. <6>[ 0.143170] devtmpfs: initialized <6>[ 0.153360] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158705] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168572] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178781] pinctrl core: initialized pinctrl subsystem <6>[ 0.183250] DMI not present or invalid. <6>[ 0.186367] NET: Registered protocol family 16 <6>[ 0.193676] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200299] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200492] cpuidle: using governor menu <6>[ 0.208596] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.385916] vdd1p1: supplied by regulator-dummy <6>[ 0.394951] vdd3p0: supplied by regulator-dummy <6>[ 0.403927] vdd2p5: supplied by regulator-dummy <6>[ 0.412919] vddarm: supplied by regulator-dummy <6>[ 0.422059] vddpu: supplied by regulator-dummy <6>[ 0.430832] vddsoc: supplied by regulator-dummy <6>[ 0.756318] No ATAGs? <6>[ 0.756502] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.764260] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.774429] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.784648] Serial: AMBA PL011 UART driver <6>[ 0.788854] printk: console [ramoops-1] enabled <6>[ 0.791145] pstore: Registered ramoops as persistent store backend <6>[ 0.797411] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.834996] iommu: Default domain type: Translated <6>[ 0.837780] vgaarb: loaded <5>[ 0.841121] SCSI subsystem initialized <6>[ 0.844814] usbcore: registered new interface driver usbfs <6>[ 0.850081] usbcore: registered new interface driver hub <6>[ 0.855596] usbcore: registered new device driver usb <6>[ 0.862398] i2c i2c-0: IMX I2C adapter registered <6>[ 0.867205] i2c i2c-1: IMX I2C adapter registered <6>[ 0.871607] i2c i2c-2: IMX I2C adapter registered <6>[ 0.877099] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.880961] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.890394] PTP clock support registered <6>[ 0.898151] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.046088] NET: Registered protocol family 2 <6>[ 2.048340] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.056683] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.064194] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.072230] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.079703] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.086344] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.093085] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.100512] NET: Registered protocol family 1 <6>[ 2.105539] RPC: Registered named UNIX socket transport module. <6>[ 2.111150] RPC: Registered udp transport module. <6>[ 2.116065] RPC: Registered tcp transport module. <6>[ 2.121046] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.127729] PCI: CLS 0 bytes, default 64 <6>[ 2.132444] Trying to unpack rootfs image as initramfs... <6>[ 3.488812] Freeing initrd memory: 15704K <4>[ 3.490772] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.498006] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.507848] Initialise system trusted keyrings <6>[ 3.511035] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.523412] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.527383] NFS: Registering the id_resolver key type <5>[ 3.532062] Key type id_resolver registered <5>[ 3.536403] Key type id_legacy registered <6>[ 3.540784] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.547627] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.555339] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.560404] Key type asymmetric registered <5>[ 3.564244] Asymmetric key parser 'x509' registered <6>[ 3.569447] bounce: pool size: 64 pages <6>[ 3.573495] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.581141] io scheduler mq-deadline registered <6>[ 3.585907] io scheduler kyber registered <6>[ 3.629524] mxs-dma 110000.dma-apbh: initialized <4>[ 3.636224] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.643172] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.695609] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.703789] SuperH (H)SCI(F) driver initialized <6>[ 3.706740] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.715613] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.723534] printk: console [ttymxc1] enabled <6>[ 3.723534] printk: console [ttymxc1] enabled <6>[ 3.732709] printk: bootconsole [ec_imx21] disabled <6>[ 3.732709] printk: bootconsole [ec_imx21] disabled <6>[ 3.744491] msm_serial: driver initialized <6>[ 3.750458] STMicroelectronics ASC driver initialized <6>[ 3.757741] STM32 USART driver initialized <4>[ 3.772577] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.780500] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.787317] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.804083] brd: module loaded <6>[ 3.817346] loop: module loaded <6>[ 3.824751] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.832985] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.841298] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.849766] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.857767] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.865525] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.873097] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.883724] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.891008] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.900084] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.910891] scsi host0: ahci-imx <6>[ 3.914757] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.935250] CAN device driver interface <6>[ 3.940696] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.950200] pps pps0: new PPS source ptp0 <6>[ 3.987376] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.994996] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.000254] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.006501] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.012185] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.024170] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.031900] usbcore: registered new interface driver pegasus <6>[ 4.037874] usbcore: registered new interface driver asix <6>[ 4.043594] usbcore: registered new interface driver ax88179_178a <6>[ 4.050006] usbcore: registered new interface driver cdc_ether <6>[ 4.056150] usbcore: registered new interface driver smsc75xx <6>[ 4.062223] usbcore: registered new interface driver smsc95xx <6>[ 4.068285] usbcore: registered new interface driver net1080 <6>[ 4.074243] usbcore: registered new interface driver cdc_subset <6>[ 4.080485] usbcore: registered new interface driver zaurus <6>[ 4.086392] usbcore: registered new interface driver cdc_ncm <6>[ 4.095897] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.102718] ehci-pci: EHCI PCI platform driver <6>[ 4.107470] ehci-platform: EHCI generic platform driver <6>[ 4.113291] ehci-orion: EHCI orion driver <6>[ 4.117791] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.122285] ehci-st: EHCI STMicroelectronics driver <6>[ 4.127613] ehci-exynos: EHCI Exynos driver <6>[ 4.132260] ehci-atmel: EHCI Atmel driver <6>[ 4.136711] tegra-ehci: Tegra EHCI driver <6>[ 4.141222] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.147686] ohci-pci: OHCI PCI platform driver <6>[ 4.152455] ohci-platform: OHCI generic platform driver <6>[ 4.158228] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.162695] ohci-st: OHCI STMicroelectronics driver <6>[ 4.168030] ohci-atmel: OHCI Atmel driver <6>[ 4.173564] usbcore: registered new interface driver usb-storage <6>[ 4.188013] i2c /dev entries driver <6>[ 4.211525] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.217978] sdhci: Copyright(c) Pierre Ossman <6>[ 4.225384] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.233641] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.240886] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.245094] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.246163] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.256935] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.259613] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.264289] usbcore: registered new interface driver usbhid <6>[ 4.268945] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.274740] usbhid: USB HID core driver <6>[ 4.281282] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.288228] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.293427] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.299422] NET: Registered protocol family 10 <6>[ 4.300612] Segment Routing with IPv6 <6>[ 4.315854] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.322638] NET: Registered protocol family 17 <6>[ 4.327363] can: controller area network core <6>[ 4.332088] NET: Registered protocol family 29 <6>[ 4.336803] can: raw protocol <6>[ 4.340066] can: broadcast manager protocol <6>[ 4.344532] can: netlink gateway - max_hops=1 <5>[ 4.349605] Key type dns_resolver registered <6>[ 4.355885] ThumbEE CPU extension supported. <5>[ 4.360476] Registering SWP/SWPB emulation handler <5>[ 4.365917] Loading compiled-in X.509 certificates <6>[ 4.376547] pstore: Using crash dump compression: deflate <4>[ 4.407852] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.415829] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.424129] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.441506] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.451536] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.456730] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.464352] mmc2: new high speed SDHC card at address 0001 <6>[ 4.471005] mmcblk2: mmc2:0001 SD 14.8 GiB <4>[ 4.487795] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 4.488134] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <4>[ 4.495498] GPT:29296874 != 30965759 <4>[ 4.504989] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.511283] GPT:29296874 != 30965759 <6>[ 4.511708] hub 1-0:1.0: USB hub found <4>[ 4.515131] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.519204] hub 1-0:1.0: 1 port detected <6>[ 4.524606] mmcblk2: p1 p2 p3 <3>[ 4.531132] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 4.539707] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 4.548102] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 4.560431] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.568354] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.576518] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.589595] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.597493] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.605664] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.616079] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.628851] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.636751] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.644996] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.658932] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 4.868174] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.069827] hub 1-1:1.0: USB hub found <6>[ 5.074059] hub 1-1:1.0: 3 ports detected <4>[ 5.088556] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.096646] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.106492] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.718687] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.738231] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.768209] Sending DHCP requests ., OK <6>[ 6.812373] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 6.820796] IP-Config: Complete: <6>[ 6.824317] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.835165] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 6.842361] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.842373] nameserver0=192.168.201.1 <6>[ 6.861476] Freeing unused kernel memory: 2048K <6>[ 6.889149] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.043879] udevd[126]: starting version 3.2.9 <5>[ 7.049774] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.056725] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.063621] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.079167] udevd[126]: specified user 'tss' unknown <27>[ 7.084640] udevd[126]: specified group 'tss' unknown <30>[ 7.092850] udevd[127]: starting eudev-3.2.9 <6>[ 7.510536] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 7.517892] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.528723] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.536678] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.585883] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.603976] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.611996] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.624580] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.644039] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.652232] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.723399] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.732079] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 7.740710] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 7.821617] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 7.822559] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.896267] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 7.900390] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.926300] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.934272] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.957024] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.962502] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.969418] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.010135] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.108468] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.128347] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.162671] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.169539] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.176182] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.185347] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.191779] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.198858] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.209335] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.217841] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.226437] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.234985] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.246982] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.255052] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.276200] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.372249] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.380562] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.389385] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.397530] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.419555] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.439385] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.447942] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.453097] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.456572] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.472848] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.500191] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.508274] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.519875] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.540150] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.548812] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.557399] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.566034] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.619976] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.627927] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.660383] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.811953] caam algorithms registered in /proc/crypto <6>[ 8.819304] caam 2100000.crypto: registering rng-caam <6>[ 8.830817] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.839377] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.847894] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done <6>[ 8.856480] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.868044] panel-simple panel-lcd: supply power not found, using dummy regulator Saving random seed: <4>[ 8.876191] panel-simple panel-lcd: Specify missing connector_type <5>[ 8.888735] random: dd: uninitialized urandom read (32 bytes read) OK <4>[ 8.901831] panel-simple panel-lvds0: supply power not found, using dummy regulator Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 9.001584] random: dropbear: uninitialized urandom read (32 bytes read) <5>[ 9.007057] random: crng init done <5>[ 9.012288] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11330349/environment . /lava-11330349/environment / # /lava-11330349/bin/lava-test-runner /lava-11330349/0 /lava-11330349/bin/lava-test-runner /lava-11330349/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11330349/0/tests/0_dmesg + cat uuid + UUID=11330349_1.5.2<8>[ 9.629567] .4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.675641] <8>[ 9.716769] <8>[ 9.757909] + set<8>[ 9.767876] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11330349/environment / # . /lava-11330349/environment/lava-11330349/bin/lava-test-runner /lava-11330349/1 / # /lava-11330349/bin/lava-test-runner /lava-11330349/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11330349/1/tests/1_bootrr + cat uuid + UUID=11330349_1.5<8>[ 10.302107] .2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11330349/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds 120000.hdmi panel-lcd panel-lvds0 backlight-lcd /lava-11330349/1/../bin/lava-test-case <8>[ 11.388987] /lava-11330349/1/../bin/lava-test-case <8>[ 11.439389] /lava-11330349/1/../bin/lava-test-case <8>[ 11.465368] + set<8>[ 11.492092] +x / #