[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11676070/tftp-deploy-5_r1k2uz/kernel/zImage tftp 0x10000000 11676070/tftp-deploy-5_r1k2uz/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '11676070/tftp-deploy-5_r1k2uz/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 14.1 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 11676070/tftp-deploy-5_r1k2uz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11676070/tftp-deploy-5_r1k2uz/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '11676070/tftp-deploy-5_r1k2uz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 14 MiB/s done Bytes transferred = 12151410 (b96a72 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11676070/tftp-deploy-5_r1k2uz/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11676070/tftp-deploy-5_r1k2uz/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '11676070/tftp-deploy-5_r1k2uz/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 8.1 MiB/s done Bytes transferred = 42645 (a695 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11676070/extract-nfsrootfs-u3du4f0h,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11676070/extract-nfsrootfs-u3du4f0h,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12151346 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d694 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.194-cip39 (KernelCI@build-j66233-arm-gcc-10-multi-v7-defconfig-fczv5) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Oct 4 10:52:42 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11676070/extract-nfsrootfs-u3du4f0h,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936488K/1048576K available (14336K kernel code, 2239K rwdata, 5360K rodata, 2048K init, 424K bss, 46552K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022197] Console: colour dummy device 80x30 <6>[ 0.024091] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034496] CPU: Testing write buffer coherency: ok <6>[ 0.039630] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044928] pid_max: default: 32768 minimum: 301 <6>[ 0.049963] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057391] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066279] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072001] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079700] rcu: Hierarchical SRCU implementation. <6>[ 0.086698] EFI services will not be available. <6>[ 0.088932] smp: Bringing up secondary CPUs ... <6>[ 0.094223] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094231] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105572] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105580] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116783] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116792] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127215] smp: Brought up 1 node, 4 CPUs <6>[ 0.131441] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137899] CPU: All CPU(s) started in SVC mode. <6>[ 0.143333] devtmpfs: initialized <6>[ 0.153495] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158842] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168707] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.178926] pinctrl core: initialized pinctrl subsystem <6>[ 0.183424] DMI not present or invalid. <6>[ 0.186511] NET: Registered protocol family 16 <6>[ 0.193807] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200443] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200635] cpuidle: using governor menu <6>[ 0.208742] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.384852] vdd1p1: supplied by regulator-dummy <6>[ 0.393863] vdd3p0: supplied by regulator-dummy <6>[ 0.402782] vdd2p5: supplied by regulator-dummy <6>[ 0.411741] vddarm: supplied by regulator-dummy <6>[ 0.420857] vddpu: supplied by regulator-dummy <6>[ 0.429581] vddsoc: supplied by regulator-dummy <6>[ 0.752399] No ATAGs? <6>[ 0.752588] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.760361] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.770527] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.780766] Serial: AMBA PL011 UART driver <6>[ 0.784940] printk: console [ramoops-1] enabled <6>[ 0.787294] pstore: Registered ramoops as persistent store backend <6>[ 0.793495] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.831260] iommu: Default domain type: Translated <6>[ 0.833987] vgaarb: loaded <5>[ 0.837425] SCSI subsystem initialized <6>[ 0.841133] usbcore: registered new interface driver usbfs <6>[ 0.846336] usbcore: registered new interface driver hub <6>[ 0.851859] usbcore: registered new device driver usb <6>[ 0.858693] i2c i2c-0: IMX I2C adapter registered <6>[ 0.863406] i2c i2c-1: IMX I2C adapter registered <6>[ 0.867882] i2c i2c-2: IMX I2C adapter registered <6>[ 0.873345] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.877247] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.886649] PTP clock support registered <6>[ 0.894381] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.047485] NET: Registered protocol family 2 <6>[ 2.049701] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.058102] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.065584] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.073607] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.081081] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.087778] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.094481] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.101893] NET: Registered protocol family 1 <6>[ 2.107023] RPC: Registered named UNIX socket transport module. <6>[ 2.112506] RPC: Registered udp transport module. <6>[ 2.117500] RPC: Registered tcp transport module. <6>[ 2.122423] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.129150] PCI: CLS 0 bytes, default 64 <6>[ 2.133826] Trying to unpack rootfs image as initramfs... <6>[ 3.096004] Freeing initrd memory: 11868K <4>[ 3.098000] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.105251] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.115077] Initialise system trusted keyrings <6>[ 3.118187] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.130461] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.134487] NFS: Registering the id_resolver key type <5>[ 3.139099] Key type id_resolver registered <5>[ 3.143451] Key type id_legacy registered <6>[ 3.147832] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.154694] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.162363] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.167460] Key type asymmetric registered <5>[ 3.171293] Asymmetric key parser 'x509' registered <6>[ 3.176499] bounce: pool size: 64 pages <6>[ 3.180544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.188189] io scheduler mq-deadline registered <6>[ 3.192957] io scheduler kyber registered <6>[ 3.236744] mxs-dma 110000.dma-apbh: initialized <4>[ 3.243435] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.250380] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.307723] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.315953] SuperH (H)SCI(F) driver initialized <6>[ 3.318875] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.327782] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.335709] printk: console [ttymxc1] enabled <6>[ 3.335709] printk: console [ttymxc1] enabled <6>[ 3.344871] printk: bootconsole [ec_imx21] disabled <6>[ 3.344871] printk: bootconsole [ec_imx21] disabled <6>[ 3.356639] msm_serial: driver initialized <6>[ 3.362568] STMicroelectronics ASC driver initialized <6>[ 3.369882] STM32 USART driver initialized <4>[ 3.384675] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.392574] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.399340] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.416126] brd: module loaded <6>[ 3.427008] loop: module loaded <6>[ 3.434309] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.442553] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.450872] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.459331] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.467356] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.475092] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.482635] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.493227] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.500508] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.509588] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.520426] scsi host0: ahci-imx <6>[ 3.524286] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.544914] CAN device driver interface <6>[ 3.550335] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.559855] pps pps0: new PPS source ptp0 <6>[ 3.582081] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.589702] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.594959] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.601210] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.606896] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.618850] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.626581] usbcore: registered new interface driver pegasus <6>[ 3.632547] usbcore: registered new interface driver asix <6>[ 3.638270] usbcore: registered new interface driver ax88179_178a <6>[ 3.644682] usbcore: registered new interface driver cdc_ether <6>[ 3.650826] usbcore: registered new interface driver smsc75xx <6>[ 3.656902] usbcore: registered new interface driver smsc95xx <6>[ 3.662948] usbcore: registered new interface driver net1080 <6>[ 3.668925] usbcore: registered new interface driver cdc_subset <6>[ 3.675178] usbcore: registered new interface driver zaurus <6>[ 3.681087] usbcore: registered new interface driver cdc_ncm <6>[ 3.690594] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.697417] ehci-pci: EHCI PCI platform driver <6>[ 3.702166] ehci-platform: EHCI generic platform driver <6>[ 3.707977] ehci-orion: EHCI orion driver <6>[ 3.712482] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.716964] ehci-st: EHCI STMicroelectronics driver <6>[ 3.722291] ehci-exynos: EHCI Exynos driver <6>[ 3.726938] ehci-atmel: EHCI Atmel driver <6>[ 3.731389] tegra-ehci: Tegra EHCI driver <6>[ 3.735903] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.742368] ohci-pci: OHCI PCI platform driver <6>[ 3.747141] ohci-platform: OHCI generic platform driver <6>[ 3.752886] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.757382] ohci-st: OHCI STMicroelectronics driver <6>[ 3.762729] ohci-atmel: OHCI Atmel driver <6>[ 3.768289] usbcore: registered new interface driver usb-storage <6>[ 3.782751] i2c /dev entries driver <6>[ 3.806295] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.812749] sdhci: Copyright(c) Pierre Ossman <6>[ 3.820157] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.828411] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.835653] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.839838] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.840918] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.851601] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.858965] usbcore: registered new interface driver usbhid <6>[ 3.864840] usbhid: USB HID core driver <6>[ 3.865887] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.874684] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.875570] NET: Registered protocol family 10 <6>[ 3.881226] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.883026] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.886945] Segment Routing with IPv6 <6>[ 3.900741] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.904531] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.918388] NET: Registered protocol family 17 <6>[ 3.923111] can: controller area network core <6>[ 3.923770] mmc2: new high speed SDHC card at address aaaa <6>[ 3.927845] NET: Registered protocol family 29 <6>[ 3.934429] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <6>[ 3.938242] can: raw protocol <6>[ 3.946192] can: broadcast manager protocol <6>[ 3.950667] can: netlink gateway - max_hops=1 <4>[ 3.951247] GPT:Primary header thinks Alt. header is not at the end of the disk. <5>[ 3.955809] Key type dns_resolver registered <4>[ 3.962985] GPT:29296874 != 31116287 <4>[ 3.971372] GPT:Alternate GPT header not at the end of the disk. <6>[ 3.973360] ThumbEE CPU extension supported. <4>[ 3.977674] GPT:29296874 != 31116287 <4>[ 3.977684] GPT: Use GNU Parted to correct GPT errors. <5>[ 3.982225] Registering SWP/SWPB emulation handler <6>[ 3.986114] mmcblk2: p1 p2 p3 <5>[ 3.996694] Loading compiled-in X.509 certificates <6>[ 4.011596] pstore: Using crash dump compression: deflate <4>[ 4.039229] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.047144] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.055100] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.071530] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.081449] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.086644] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.114482] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.121608] hub 1-0:1.0: USB hub found <6>[ 4.125757] hub 1-0:1.0: 1 port detected <6>[ 4.134317] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.149595] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.157520] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.165427] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.177547] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.185455] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.193255] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.203350] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.215556] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.223429] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.231346] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.245478] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.464452] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.666092] hub 1-1:1.0: USB hub found <6>[ 4.670327] hub 1-1:1.0: 3 ports detected <4>[ 4.684707] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.692742] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.702558] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.364861] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.374435] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.404513] Sending DHCP requests ., OK <6>[ 7.448575] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 <6>[ 7.456930] IP-Config: Complete: <6>[ 7.460452] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.471200] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) <6>[ 7.479349] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.479361] nameserver0=192.168.201.1 <6>[ 7.497983] Freeing unused kernel memory: 2048K <6>[ 7.524893] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.412166] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.419224] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.429788] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.437832] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.456760] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.479453] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.479847] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.488085] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.495881] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.504321] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.519255] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.567553] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.605510] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.613345] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.621612] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.623688] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.628506] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.694611] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.722747] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.726640] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.730861] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.742646] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.744466] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.755360] caam 2100000.crypto: Instantiated RNG4 SH1 <4>[ 8.760217] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.765495] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.765506] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.791562] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.798118] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.804537] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.811640] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.820708] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.829385] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.837976] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.846540] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.857015] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.865028] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.873758] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.892555] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.901224] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.909816] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.918390] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.941127] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.949233] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.969427] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.999397] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.008034] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.016605] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.025157] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.152958] caam algorithms registered in /proc/crypto <6>[ 9.163748] caam 2100000.crypto: registering rng-caam <4>[ 9.172195] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.180608] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.192613] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.209294] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.217863] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.226428] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.234977] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.246822] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.254923] panel-simple panel-lcd: Specify missing connector_type Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... <5>[ 9.351730] random: crng init done Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.498425] systemd[1]: System time before build time, advancing clock. <30>[ 10.547516] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.571826] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.617152] systemd[1]: Set hostname to . <30>[ 11.383748] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.393374] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.406243] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.415868] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.456017] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.495950] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.535576] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.574812] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.615172] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.655277] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.667835] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.705564] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.734605] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.774754] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.804983] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.835731] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.907748] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.917385] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.955953] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.996633] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 12.037494] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 12.075173] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 12.115741] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 12.125345] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 12.137931] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 12.180931] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 12.218717] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 12.261066] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.298117] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.341275] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.377718] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.390800] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.433491] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.478312] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.517685] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.570034] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.615138] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.665609] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.728370] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... <46>[ 13.015259] systemd-journald[273]: Received client request to flush runtime journal. Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.194-cip39 #1 SMP Wed Oct 4 10:52:42 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11676070/extract-nfsrootfs-u3du4f0h' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11676070/extract-nfsrootfs-u3du4f0h' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11676070/environment . /lava-11676070/environment / # /lava-11676070/bin/lava-test-runner /lava-11676070/0 /lava-11676070/bin/lava-test-runner /lava-11676070/0 + export TESTRUN_ID=0_dmesg + cd /lava-11676070/0/tests/0_dmesg + cat uuid + UUID=11676070_1.6.2.4.1<8>[ 26.613009] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 26.697773] <8>[ 26.762685] <8>[ 26.829482] + set<8>[ 26.839109] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11676070/environment / # . /lava-11676070/environment/lava-11676070/bin/lava-test-runner /lava-11676070/1 / # /lava-11676070/bin/lava-test-runner /lava-11676070/1 + export TESTRUN_ID=1_bootrr + cd /lava-11676070/1/tests/1_bootrr + cat uuid + UUID=11676070_1.6.2.4.5<8>[ 27.389392] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11676070/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds ldb panel-lcd /lava-11676070/1/../bin/lava-test-case <8>[ 28.512239] /lava-11676070/1/../bin/lava-test-case <8>[ 28.575840] /lava-11676070/1/../bin/lava-test-case <8>[ 28.611345] + set +x<8>[ 28.637709] / #