Trying 192.168.1.205... Connected to ts5. Escape character is '^]'. ser2net port telnet,2002 device serialdev,/dev/ttyUSB-lf-bbb-02,115200n81,local [] (Debian GNU/Linux) U-Boot SPL 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) Trying to boot from MMC2 U-Boot 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 172.16.3.199 (81 ms) => setenv serverip 172.16.3.3 setenv serverip 172.16.3.3 => tftp 0x82000000 1053322/tftp-deploy-m7001vu7/kernel/zImage tftp 0x82000000 1053322/tftp-deploy-m7001vu7/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.199 Filename '1053322/tftp-deploy-m7001vu7/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 3.5 MiB/s done Bytes transferred = 4609536 (465600 hex) => tftp 0x83000000 1053322/tftp-deploy-m7001vu7/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1053322/tftp-deploy-m7001vu7/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.199 Filename '1053322/tftp-deploy-m7001vu7/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 10.4 MiB 3.4 MiB/s done Bytes transferred = 10927074 (a6bbe2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1053322/tftp-deploy-m7001vu7/dtb/am335x-boneblack.dtb tftp 0x88000000 1053322/tftp-deploy-m7001vu7/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.199 Filename '1053322/tftp-deploy-m7001vu7/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 3 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=172.16.3.3:/var/lib/lava/dispatcher/tmp/1053322/extract-nfsrootfs-xohsqn8c,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=172.16.3.3:/var/lib/lava/dispatcher/tmp/1053322/extract-nfsrootfs-xohsqn8c,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x465600 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-12-07 13:25:33 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10927010 Bytes = 10.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip41 (KernelCI@build-j37630-arm-gcc-10-omap2plus-defconfig-7z2ck) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Dec 7 12:04:00 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=172.16.3.3:/var/lib/lava/dispatcher/tmp/1053322/extract-nfsrootfs-xohsqn8c,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 475196K/522240K available (9216K kernel code, 1027K rwdata, 2180K rodata, 1024K init, 278K bss, 30660K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018569] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030217] Console: colour dummy device 80x30 <3>[ 0.035089] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042149] This ensures that you still see kernel messages. Please <3>[ 0.048874] update your kernel commandline. <6>[ 0.053477] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095548] CPU: Testing write buffer coherency: ok <6>[ 0.100931] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106396] pid_max: default: 32768 minimum: 301 <6>[ 0.111558] LSM: Security Framework initializing <6>[ 0.116658] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124474] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134139] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140651] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147848] rcu: Hierarchical SRCU implementation. <6>[ 0.153648] smp: Bringing up secondary CPUs ... <6>[ 0.158585] smp: Brought up 1 node, 1 CPU <6>[ 0.163013] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169744] CPU: All CPU(s) started in SVC mode. <6>[ 0.175475] devtmpfs: initialized <6>[ 0.191326] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199865] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210301] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218956] pinctrl core: initialized pinctrl subsystem <6>[ 0.226533] NET: Registered protocol family 16 <6>[ 0.234224] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260718] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266813] audit: initializing netlink subsys (disabled) <6>[ 0.273896] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273909] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280519] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287243] cpuidle: using governor menu <5>[ 1.166017] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.291155] No ATAGs? <6>[ 1.293783] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.318156] Kprobes globally optimized <6>[ 1.331426] iommu: Default domain type: Translated <6>[ 1.338454] vgaarb: loaded <5>[ 1.342168] SCSI subsystem initialized <6>[ 1.347464] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.352951] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.362673] PTP clock support registered <6>[ 1.368251] clocksource: Switched to clocksource dmtimer <5>[ 2.006123] VFS: Disk quotas dquot_6.6.0 <6>[ 2.010638] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.027532] NET: Registered protocol family 2 <6>[ 2.032719] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.041389] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.050348] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.058645] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.066305] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.073244] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.080277] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.087883] NET: Registered protocol family 1 <6>[ 2.093687] RPC: Registered named UNIX socket transport module. <6>[ 2.100148] RPC: Registered udp transport module. <6>[ 2.105256] RPC: Registered tcp transport module. <6>[ 2.110382] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.117289] PCI: CLS 0 bytes, default 64 <6>[ 2.122330] Trying to unpack rootfs image as initramfs... <6>[ 2.840556] Freeing initrd memory: 10672K <6>[ 2.846219] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.856630] Initialise system trusted keyrings <6>[ 2.862110] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 2.870478] NFS: Registering the id_resolver key type <5>[ 2.876004] Key type id_resolver registered <5>[ 2.880663] Key type id_legacy registered <6>[ 2.885116] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 2.893132] Key type asymmetric registered <5>[ 2.897623] Asymmetric key parser 'x509' registered <6>[ 2.902973] io scheduler mq-deadline registered <6>[ 2.907903] io scheduler kyber registered <3>[ 3.046147] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.054864] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.163737] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.205823] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.277653] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.286370] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.346244] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.354944] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.372518] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.381211] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.444750] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.453317] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.480384] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.494925] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.505873] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.515308] printk: console [ttyS0] enabled <6>[ 3.515308] printk: console [ttyS0] enabled <6>[ 3.524376] printk: bootconsole [omap8250] disabled <6>[ 3.524376] printk: bootconsole [omap8250] disabled <6>[ 3.548009] brd: module loaded <6>[ 3.558964] loop: module loaded <3>[ 3.564421] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.638242] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.667537] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.677477] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.684191] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.690005] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.697504] cpsw 4a100000.ethernet: Detected MACID = 04:79:b7:e7:06:e0 <6>[ 3.706540] i2c /dev entries driver <5>[ 3.712180] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 3.720075] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.726555] sdhci: Copyright(c) Pierre Ossman <6>[ 3.731972] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 3.740262] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.750121] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.758628] Initializing XFRM netlink socket <6>[ 3.763404] NET: Registered protocol family 10 <6>[ 3.769910] Segment Routing with IPv6 <6>[ 3.773956] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.781025] NET: Registered protocol family 17 <6>[ 3.785788] NET: Registered protocol family 15 <5>[ 3.790713] Key type dns_resolver registered <6>[ 3.795870] oprofile: using arm/armv7 <6>[ 3.800016] ThumbEE CPU extension supported. <5>[ 3.804597] Registering SWP/SWPB emulation handler <3>[ 3.810111] omap_voltage_late_init: Voltage driver support not added <3>[ 3.816774] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 3.825219] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 3.833908] SmartReflex Class3 initialized <6>[ 3.838765] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 3.847616] Loading compiled-in X.509 certificates <6>[ 3.872849] OMAP GPIO hardware version 0.1 <4>[ 3.908921] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 3.922589] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 3.931403] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 3.937741] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 3.947797] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 3.959252] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 3.968348] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 3.973514] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.983946] mmc1: new high speed MMC card at address 0001 <6>[ 3.990891] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 3.996153] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.002935] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.010432] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.020821] mmcblk1: p1 <6>[ 4.044616] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.054272] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.139807] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 6.288915] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.318245] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.348372] Sending DHCP requests ., OK <6>[ 6.492329] IP-Config: Got DHCP answer from 172.16.3.3, my address is 172.16.3.199 <6>[ 6.500229] IP-Config: Complete: <6>[ 6.503740] device=eth0, hwaddr=04:79:b7:e7:06:e0, ipaddr=172.16.3.199, mask=255.255.255.0, gw=172.16.3.3 <6>[ 6.514064] host=172.16.3.199, domain=denx.de, nis-domain=(none) <6>[ 6.520811] bootserver=172.16.3.33, rootserver=172.16.3.3, rootpath= <6>[ 6.520818] nameserver0=172.16.3.3 <6>[ 6.532024] ntpserver0=172.16.3.3 <6>[ 6.538937] Freeing unused kernel memory: 1024K <6>[ 6.558711] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.12-1~deb12u1 <4>[ 7.823924] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 7.907790] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <3>[ 7.924310] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 7.963938] remoteproc remoteproc0: wkup_m3 is available <6>[ 7.992750] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 8.000471] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 8.029073] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 8.034495] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:01 UTC (946684801) <6>[ 8.048718] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 8.057474] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 8.087227] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.096387] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 8.133485] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 8.202712] usbcore: registered new interface driver usbfs <6>[ 8.208772] usbcore: registered new interface driver hub <6>[ 8.214456] usbcore: registered new device driver usb <4>[ 8.223297] at24 2-0056: supply vcc not found, using dummy regulator <3>[ 8.258809] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 8.302417] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 8.399215] tda998x 0-0070: found TDA19988 <6>[ 8.588705] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 8.723059] davinci-mcasp 48038000.mcasp: IRQ common not found <4>[ 8.802351] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.811476] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.821316] remoteproc remoteproc0: powering up wkup_m3 <4>[ 8.864712] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 8.874697] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 8.880954] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 8.964503] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 8.971886] random: crng init done <6>[ 9.040080] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.045735] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.169485] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 9.186681] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 9.258068] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <3>[ 9.267944] PM: Cannot get wkup_m3_ipc handle <6>[ 9.280939] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 9.308762] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.317354] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.324955] usb usb1: Product: MUSB HDRC host driver <6>[ 9.330226] usb usb1: Manufacturer: Linux 5.10.201-cip41 musb-hcd <6>[ 9.336607] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.348778] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 9.378666] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 9.424394] omap-aes 53500000.aes: will run requests pump with realtime priority <6>[ 9.475220] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 9.644326] hub 1-0:1.0: USB hub found <6>[ 9.678446] hub 1-0:1.0: 1 port detected <3>[ 9.693277] PM: Cannot get wkup_m3_ipc handle <3>[ 9.936194] PM: Cannot get wkup_m3_ipc handle <3>[ 9.975073] PM: Cannot get wkup_m3_ipc handle Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: eth0 hardware address 04:79:b7:e7:06:e0 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 172.16.3.3): address: 172.16.3.199 broadcast: 172.16.3.255 netmask: 255.255.255.0 gateway: 172.16.3.3 dns0 : 172.16.3.3 dns1 : 0.0.0.0 domain : denx.de rootserver: 172.16.3.33 rootpath: filename : this-host-is-not-configured.kpxe done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... mount: No such file or directory mount: invalid option -- done. mount: No such file or directory run-init: opening console: No such file or directory Target filesystem doesn't have requested /sbin/init. run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory No init found. Try passing init= bootarg. (initramfs) <3>[ 64.528883] PM: Cannot get wkup_m3_ipc handle <6>[ 64.533771] platform pm33xx: deferred probe pending