connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='default', state=, avail=True, host='nuc-1', port=38073, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:38073 connected to 192.168.0.1 (port 38073) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.0.135 U-Boot>setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3995544/tftp-deploy-k0q4hako/kernel/zImage tftp 0x22100000 3995544/tftp-deploy-k0q4hako/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3995544/tftp-deploy-k0q4hako/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 3.2 MiB/s done Bytes transferred = 5851032 (594798 hex) U-Boot> tftp 0x23000000 3995544/tftp-deploy-k0q4hako/ramdisk/ramdisk.cpio.gz.uboot tftp 0x23000000 3995544/tftp-deploy-k0q4hako/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3995544/tftp-deploy-k0q4hako/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 2.8 MiB/s done Bytes transferred = 8768449 (85cbc1 hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3995544/tftp-deploy-k0q4hako/dtb/at91-sama5d4_xplained.dtb tftp 0x22000000 3995544/tftp-deploy-k0q4hako/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3995544/tftp-deploy-k0q4hako/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 2.2 MiB/s done Bytes transferred = 36163 (8d43 hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0x594798 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 8768385 Bytes = 8.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200bd42 Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 6.9.0-rc5-next-20240426 (KernelCI@build-j177796-arm-gcc-10-sama5-defconfig-7x2tb) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Fri Apr 26 08:01:56 UTC 2024 CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt: Machine model: Atmel SAMA5D4 Xplained earlycon: atmel_serial0 at MMIO 0xfc00c000 (options '115200n8') printk: legacy bootconsole [atmel_serial0] enabled Memory policy: Data cache writeback Zone ranges: Normal [mem 0x0000000020000000-0x000000003fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000020000000-0x000000003fffffff] Initmem setup node 0 [mem 0x0000000020000000-0x000000003fffffff] CPU: All CPU(s) started in SVC mode. Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>Built 1 zonelists, mobility grouping on. Total pages: 131072 <6>mem auto-init: stack:off, heap alloc:off, heap free:off, mlocked free:off <6>Memory: 497320K/524288K available (9216K kernel code, 272K rwdata, 2348K rodata, 1024K init, 136K bss, 26968K reserved, 0K cma-reserved) <6>SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>L2C-310 dynamic clock gating enabled, standby mode enabled <6>L2C-310 cache controller enabled, 8 ways, 128 kB <6>L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>clocksource: timer@fc024000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>sched_clock: 32 bits at 11MHz, resolution 90ns, wraps every 195225786322ns <6>Switching to timer-based delay loop, resolution 90ns <6>Console: colour dummy device 80x30 <6>Calibrating delay loop (skipped), value calculated using timer frequency.. 22.00 BogoMIPS (lpj=110000) <6>CPU: Testing write buffer coherency: ok <6>pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>Setting up static identity map for 0x20100000 - 0x20100060 <6>devtmpfs: initialized <6>VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>futex hash table entries: 256 (order: -1, 3072 bytes, linear) <6>pinctrl core: initialized pinctrl subsystem <6>NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>DMA: preallocated 256 KiB pool for atomic coherent allocations <6>AT91: PM: standby: standby, suspend: standby <4>gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>gpio-at91 fc06a000.gpio: at address (ptrval) <4>gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>gpio-at91 fc06b000.gpio: at address (ptrval) <4>gpio gpiochip2: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>gpio-at91 fc06c000.gpio: at address (ptrval) <4>gpio gpiochip3: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>gpio-at91 fc068000.gpio: at address (ptrval) <4>gpio gpiochip4: Static allocation of GPIO base is deprecated, use dynamic allocation. <6>gpio-at91 fc06d000.gpio: at address (ptrval) <6>pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>AT91: Detected SoC family: sama5d4 <6>AT91: Detected SoC: sama5d44, revision 0 <5>SCSI subsystem initialized <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>at91_i2c f8014000.i2c: using dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers <6>i2c i2c-0: using pinctrl states for GPIO recovery <6>i2c i2c-0: using generic GPIOs for recovery <6>at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <6>mc: Linux media interface: v0.10 <6>videodev: Linux video capture interface: v2.00 <6>pps_core: LinuxPPS API ver. 1 registered <6>pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>PTP clock support registered <6>Advanced Linux Sound Architecture Driver Initialized. <6>clocksource: Switched to clocksource timer@fc024000 <6>NET: Registered PF_INET protocol family <6>IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>TCP: Hash tables configured (established 4096 bind 4096) <6>UDP hash table entries: 256 (order: 0, 4096 bytes, linear) <6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) <6>NET: Registered PF_UNIX/PF_LOCAL protocol family <6>RPC: Registered named UNIX socket transport module. <6>RPC: Registered udp transport module. <6>RPC: Registered tcp transport module. <6>RPC: Registered tcp-with-tls transport module. <6>RPC: Registered tcp NFSv4.1 backchannel transport module. <5>Initialise system trusted keyrings <6>Trying to unpack rootfs image as initramfs... <6>workingset: timestamp_bits=30 max_order=17 bucket_order=0 <5>Key type asymmetric registered <5>Asymmetric key parser 'x509' registered <6>io scheduler mq-deadline registered <6>io scheduler kyber registered <6>io scheduler bfq registered <5>random: crng init done <6>brd: module loaded <6>loop: module loaded <6>atmel_usart_serial.0.auto: ttyS5 at MMIO 0xf8004000 (irq = 25, base_baud = 5500000) is a ATMEL_SERIAL <6>atmel_usart_serial.1.auto: ttyS0 at MMIO 0xfc00c000 (irq = 26, base_baud = 5500000) is a ATMEL_SERIAL