Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 172.16.0.69 (256 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 514110/tftp-deploy-8riqfpgz/kernel/Image tftp 0x82000000 514110/tftp-deploy-8riqfpgz/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.69; sending through gateway 172.16.0.254 Filename '514110/tftp-deploy-8riqfpgz/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################# 13.9 MiB/s done Bytes transferred = 27191808 (19eea00 hex) => tftp 0x90080000 514110/tftp-deploy-8riqfpgz/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 514110/tftp-deploy-8riqfpgz/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.69; sending through gateway 172.16.0.254 Filename '514110/tftp-deploy-8riqfpgz/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################## 5.6 MiB/s done Bytes transferred = 19030446 (12261ae hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 514110/tftp-deploy-8riqfpgz/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 514110/tftp-deploy-8riqfpgz/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.69; sending through gateway 172.16.0.254 Filename '514110/tftp-deploy-8riqfpgz/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *## 6 MiB/s done Bytes transferred = 25056 (61e0 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2024-11-11 14:44:27 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 19030382 Bytes = 18.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900091df WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.226 (KernelCI@build-j372842-arm64-clang-17-defconfig-config-randomize-ba4zzmm) (Debian clang version 17.0.6 (++20231208085813+6009708b4367-1~exp1~20231208085906.81), Debian LLD 17.0.6) #1 SMP PREEMPT Mon Nov 11 14:12:35 UTC 2024 [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7dda80-0x20ff7dffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 [ 0.000000] percpu: Embedded 23 pages/cpu s56856 r8192 d29160 u94208 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: Spectre-v3a [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3969588K/4194304K available (14784K kernel code, 2746K rwdata, 7300K rodata, 1600K init, 528K bss, 191948K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080080000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x0000002080030000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000002080040000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000002] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008706] Console: colour dummy device 80x25 <6>[ 0.013493] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.024212] pid_max: default: 32768 minimum: 301 <6>[ 0.029167] LSM: Security Framework initializing <6>[ 0.034136] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.041892] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.050958] rcu: Hierarchical SRCU implementation. <6>[ 0.056198] Platform MSI: gic-its@6020000 domain created <6>[ 0.061895] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.069752] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.075872] EFI services will not be available. <6>[ 0.080807] smp: Bringing up secondary CPUs ... <6>[ 0.085930] Detected PIPT I-cache on CPU1 <6>[ 0.085948] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.085955] GICv3: CPU1: using allocated LPI pending table @0x0000002080050000 <6>[ 0.085978] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.086033] smp: Brought up 1 node, 2 CPUs <6>[ 0.116347] SMP: Total of 2 processors activated. <6>[ 0.121359] CPU features: detected: 32-bit EL0 Support <6>[ 0.126817] CPU features: detected: CRC32 instructions <6>[ 0.132268] CPU features: detected: 32-bit EL1 Support <6>[ 0.148231] CPU: All CPU(s) started at EL2 <6>[ 0.152650] alternatives: patching kernel code <6>[ 0.158197] devtmpfs: initialized <4>[ 0.163995] KASLR disabled due to lack of seed <6>[ 0.168862] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.178970] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.186647] pinctrl core: initialized pinctrl subsystem <6>[ 0.192806] DMI not present or invalid. <6>[ 0.197306] NET: Registered protocol family 16 <6>[ 0.202957] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.210452] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.218574] audit: initializing netlink subsys (disabled) <5>[ 0.224378] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.224882] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.232466] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.238948] cpuidle: using governor menu <6>[ 0.250124] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.257266] ASID allocator initialised with 65536 entries <6>[ 0.263528] Serial: AMBA PL011 UART driver <6>[ 0.270647] Machine: Kontron KBox A-230-LS <6>[ 0.275049] SoC family: QorIQ LS1028A <6>[ 0.279003] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.295974] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.303013] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.310043] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.317071] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.326132] ACPI: Interpreter disabled. <6>[ 0.331164] iommu: Default domain type: Translated <6>[ 0.336466] vgaarb: loaded <5>[ 0.339611] SCSI subsystem initialized <6>[ 0.343930] usbcore: registered new interface driver usbfs <6>[ 0.349756] usbcore: registered new interface driver hub <6>[ 0.355396] usbcore: registered new device driver usb <6>[ 0.361008] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.368825] i2c i2c-0: IMX I2C adapter registered <6>[ 0.373999] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.381663] i2c i2c-1: IMX I2C adapter registered <6>[ 0.386769] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.394412] i2c i2c-2: IMX I2C adapter registered <6>[ 0.399645] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.404921] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.414422] PTP clock support registered <6>[ 0.418717] EDAC MC: Ver: 3.0.0 <6>[ 0.422812] FPGA manager framework <6>[ 0.426546] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.433343] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.439864] VFS: Disk quotas dquot_6.6.0 <6>[ 0.444115] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.451418] pnp: PnP ACPI: disabled <6>[ 0.458395] NET: Registered protocol family 2 <6>[ 0.463357] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.472516] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) <6>[ 0.481438] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.489777] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear) <6>[ 0.497773] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 0.504735] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.511787] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) <6>[ 0.519348] NET: Registered protocol family 1 <6>[ 0.524310] RPC: Registered named UNIX socket transport module. <6>[ 0.530554] RPC: Registered udp transport module. <6>[ 0.535565] RPC: Registered tcp transport module. <6>[ 0.540577] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.547346] PCI: CLS 0 bytes, default 64 <6>[ 0.551649] Unpacking initramfs... <6>[ 1.224449] Freeing initrd memory: 18580K <6>[ 1.229093] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 1.237812] kvm [1]: IPA Size Limit: 44 bits <6>[ 1.243063] kvm [1]: GICv3: no GICV resource entry <6>[ 1.248165] kvm [1]: disabling GICv2 emulation <6>[ 1.252925] kvm [1]: GIC system register CPU interface enabled <6>[ 1.259103] kvm [1]: vgic interrupt IRQ9 <6>[ 1.263404] kvm [1]: Hyp mode initialized successfully <4>[ 1.269362] NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #80!!! <5>[ 1.278162] Initialise system trusted keyrings <6>[ 1.283010] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 1.292902] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.299434] NFS: Registering the id_resolver key type <5>[ 1.304812] Key type id_resolver registered <5>[ 1.309297] Key type id_legacy registered <6>[ 1.313650] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.320680] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.328497] 9p: Installing v9fs 9p2000 file system support <5>[ 1.362592] Key type asymmetric registered <5>[ 1.366993] Asymmetric key parser 'x509' registered <6>[ 1.372198] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.379930] io scheduler mq-deadline registered <6>[ 1.384770] io scheduler kyber registered <4>[ 1.394551] EINJ: ACPI disabled. <6>[ 1.405328] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.413192] printk: console [ttyS0] disabled <6>[ 1.417818] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.426986] printk: console [ttyS0] enabled <6>[ 1.426986] printk: console [ttyS0] enabled <6>[ 1.435926] printk: bootconsole [ns16550a0] disabled <6>[ 1.435926] printk: bootconsole [ns16550a0] disabled <6>[ 1.446764] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 1.456129] SuperH (H)SCI(F) driver initialized <6>[ 1.461217] msm_serial: driver initialized <6>[ 1.469151] loop: module loaded <6>[ 1.477314] megasas: 07.714.04.00-rc1 <6>[ 1.483400] spi-nor spi0.0: w25q32dw (4096 Kbytes) <5>[ 1.497035] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 1.504124] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 1.509643] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 1.517759] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 1.525734] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 1.533731] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 1.545719] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 1.553728] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 1.561730] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 1.569728] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 1.579492] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.585271] thunder_xcv, ver 1.0 <6>[ 1.588793] thunder_bgx, ver 1.0 <6>[ 1.592309] nicpf, ver 1.0 <6>[ 1.595973] hclge is initializing <6>[ 1.599572] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.607086] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.612699] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.617855] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.623903] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.629146] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.635366] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.641045] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.646911] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.653462] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.659846] sky2: driver version 1.30 <6>[ 1.664379] VFIO - User Level meta-driver version: 0.3 <6>[ 1.670870] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.677701] ehci-pci: EHCI PCI platform driver <6>[ 1.682442] ehci-platform: EHCI generic platform driver <6>[ 1.688018] ehci-orion: EHCI orion driver <6>[ 1.692359] ehci-exynos: EHCI Exynos driver <6>[ 1.696867] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.703343] ohci-pci: OHCI PCI platform driver <6>[ 1.708082] ohci-platform: OHCI generic platform driver <6>[ 1.713651] ohci-exynos: OHCI Exynos driver <6>[ 1.718381] usbcore: registered new interface driver usb-storage <6>[ 1.726181] i2c /dev entries driver <6>[ 1.732609] sp805-wdt c000000.watchdog: registration successful <6>[ 1.738924] sp805-wdt c010000.watchdog: registration successful <6>[ 1.746303] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 1.754962] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.761440] sdhci: Copyright(c) Pierre Ossman <6>[ 1.766374] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.773220] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.780114] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.787243] usbcore: registered new interface driver usbhid <6>[ 1.793103] usbhid: USB HID core driver <6>[ 1.799886] NET: Registered protocol family 17 <6>[ 1.804715] 9pnet: Installing 9P2000 support <5>[ 1.809298] Key type dns_resolver registered <6>[ 1.814049] registered taskstats version 1 <5>[ 1.818427] Loading compiled-in X.509 certificates <4>[ 1.823576] <4>[ 1.825327] ******************************************************************** <4>[ 1.833018] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 1.840702] ** ** <4>[ 1.848386] ** WRITEABLE clk DebugFS SUPPORT HAS BEEN ENABLED IN THIS KERNEL ** <4>[ 1.856070] ** ** <4>[ 1.863759] ** This means that this kernel is built to expose clk operations ** <4>[ 1.871443] ** such as parent or rate setting, enabling, disabling, etc. ** <4>[ 1.879129] ** to userspace, which may compromise security on your system. ** <4>[ 1.886813] ** ** <4>[ 1.894497] ** If you see this message and you are not debugging the ** <4>[ 1.902180] ** kernel, report this immediately to your vendor! ** <4>[ 1.909863] ** ** <4>[ 1.917546] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 1.925230] ******************************************************************** <6>[ 1.947017] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 14.245401] clk: Disabling unused clocks <6>[ 14.249731] ALSA device list: <6>[ 14.252990] No soundcards found. <6>[ 14.258591] Freeing unused kernel memory: 1600K <6>[ 14.263839] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.324315] udevd[109]: starting version 3.2.9 <5>[ 14.329618] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.336436] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.343228] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 14.352631] udevd[109]: specified user 'tss' unknown <27>[ 14.358027] udevd[109]: specified group 'tss' unknown <30>[ 14.364269] udevd[110]: starting eudev-3.2.9 <4>[ 14.554208] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 14.579583] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 14.598618] rtc-rv8803 0-0032: Voltage low, data loss detected. <6>[ 14.606757] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 14.617579] at24 1-0057: supply vcc not found, using dummy regulator <4>[ 14.627472] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 14.634022] rtc-rv8803 0-0032: registered as rtc0 <6>[ 14.639485] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 14.646722] at24 2-0050: supply vcc not found, using dummy regulator <4>[ 14.652845] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 14.659921] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <3>[ 14.662272] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 14.679922] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 14.722306] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <5>[ 14.743676] arm-smmu 5000000.iommu: probing hardware configuration... <6>[ 14.752051] caam 8000000.crypto: job rings = 4, qi = 0 <5>[ 14.759917] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 14.765122] arm-smmu 5000000.iommu: stage 1 translation <5>[ 14.771018] arm-smmu 5000000.iommu: stage 2 translation <5>[ 14.785280] arm-smmu 5000000.iommu: nested translation <5>[ 14.790839] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 14.798305] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 14.805126] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 14.811861] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 14.818594] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 14.826443] mali-dp f080000.display: Adding to iommu group 0 done <6>[ 14.832840] fsl-edma 22c0000.dma-controller: Adding to iommu group 1 Saving random seed: <6>[ 14.841466] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: OK <6>[ 14.850469] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 Starting network<6>[ 14.859784] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 : <6>[ 14.870213] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 OK<6>[ 14.879378] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 14.888633] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 14.897728] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 14.906980] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 14.916139] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 14.925275] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 Starting dropbea<6>[ 14.932540] pci_bus 0000:00: root bus resource [bus 00] r sshd: <6>[ 14.939439] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 14.950857] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 14.961991] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 14.972659] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 14.974199] NET: Registered protocol family 10 <6>[ 14.983769] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 14.989129] Segment Routing with IPv6 <6>[ 14.999135] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) OK<6>[ 15.014206] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 15.025077] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 15.025111] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.025116] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.025121] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 15.025125] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) /bin/sh: <6>[ 15.025145] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 15.025156] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) can't access tty<6>[ 15.025159] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) ; job control tu<6>[ 15.025367] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 rned off<6>[ 15.112368] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.123784] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) / # <6>[ 15.135115] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, pro perties 0x4) <6>[ 15.146461] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 15.157916] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 15.163701] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 15.173918] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 15.184770] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 15.191100] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.201843] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.213035] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 15.218951] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 / # <6>[ 15.225425] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.236417] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.247607] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 15.253530] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 15.259855] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.270597] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000# -0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.281792] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 15.287687] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 15.294011] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.304755] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 15.315935] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.326688] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 15.332603] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 15.338942] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 15.349691] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) #<6>[ 15.360918] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 15.367711] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 15.374162] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 15.383187] fsl_enetc 0000:00:00.0: Adding to iommu group 2 / # export SHELL=/bin/sh export SHELL=/bin/sh<6>[ 15.497398] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 15.503916] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 1e:27:56:4d:02:f4 <6>[ 15.512750] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 7e:b7:45:bc:40:5c / # <6>[ 15.534391] fsl_enetc 0000:00:00.1: Adding to iommu group 3 <6>[ 15.539918] fsl_enetc 0000:00:00.0 enp0s0f0: renamed from eth0 . /lava-514110/environment . /lava-514110/environment<6>[ 15.645418] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 15.651943] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using 12:75:40:50:a5:ef <6>[ 15.660778] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using ea:ed:14:cd:b9:18 / # <6>[ 15.681521] fsl_enetc 0000:00:00.2: Adding to iommu group 4 <6>[ 15.682491] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth0 /lava-514110/bin/lava-test-runner /lava-514110/0 /lava-514110/bin/lava-test-runner /lava-514110/0<6>[ 15.797421] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 15.803947] fsl_enetc 0000:00:00.2: no MAC address specified for SI0, using f6:50:f7:22:f3:18 <6>[ 15.814088] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 5 <6>[ 15.815515] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth0 + export 'TESTRUN_ID=0_dmesg' + c<8>[ 15.849172] d /lava-514110/0/tests/0_dmesg + cat uuid + UUID=514110_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.867925] <8>[ 15.886900] <8>[ 15.906103] + <8>[ 15.915350] set +x <4>[ 15.990876] ptp_qoriq: device tree node missing required elements, try automatic configurati�